Download C2R-CHY4
Transcript
C2R-CHY4 Radio Replacement Interface with Nav Outputs for all Chrysler Dodge / Jeep CANbus Vehicles With or Without Premium Audio Systems J1850 CRC Class 2 1 0 0 0 111 0 1111 0 0 1 0 0 11 0 11 0 0 Radio Connection Chart White / Black Front L - input Grey Front R + input Grey / Black Front R - input Green Rear L + input Green / Black Rear L - input Purple Rear R + input Purple / Black Rear R - input CAN Interface Connection Chart: Red Acc. Output (1 amp) Red / White P.B. Output (-) Purple / White VSS Output (Pulse) Orange / White Illum. Output (+) 2 11 Front L + input 3 White 4 Antenna On Input 5 Blue Radio Connections. See aside Chart for color description. SWC Interface. Program for Version 2 Ground CAN INTERFACE Black Accessory Output +12volts 1amp max. Battery +12v Class 2 111 0 1 0 0 0 0 11 0 11 0 111 0 0 11 0 0 Navigation outputs and Amplifier Remote Input See Chart for wire color descriptions. (Read the Installation Notes before making connections to the provided radio harness) Yellow J1850 11 10 9 8 7 6 EOD 111 0 1 0 0 0 0 11 0 11 0 111 0 0 11 0 0 2 11 Class 2 3 J1850 4 Class 2 5 Arbitration 11 10 9 8 7 6 VPW 1 0 0 0 111 0 1111 0 0 1 0 0 11 0 11 0 0 Chrysler Radio Specific Steering Wheel Control Interface (Sold Separately) Program SWC Interface for Version 2. Installation Notes 1. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your particular vehicle. 2. Vehicles without a factory amplifier: Connect the aftermarket radio’s front and Green Reverse Output (+) rear speaker wires to the 22 pin plug. White / Green SWC Output 3. Vehicles with a factory amplifier: The factory amplifier only accepts two audio Blue / White Amp Turn On Input channels (left and right). The amplifier’s fading is controlled by data communication from the factory radio. The aftermarket radio does not have the ability to control the amplifier’s fader. Connect the front outputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This will allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. 4. The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory wire. The accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (fig. 1: If more current is needed). 5. 11 pin plug (to CAN INTERFACE): 1. Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp present! 2. White/Green - SWC output. Fig. 1 High Current 12v (using a SPDT relay) 3. Green - Connect this wire to the radio’s reverse input wire only. (Fused) 4. Orange/White - Connect this wire to the radio’s Illumination input wire only. 5. Violet/White - Connect this wire to the radio’s VSS input wire only. 85 86 87 12v Acc. 6. Red/White - Connect this wire to the radio’s parking brake input wire only. Note: Do not connect these wires to any circuit other than the radio’s wire harness. From Interface 87a Ground 6. 11 pin plug (to SWC INTERFACE): 30 This is a quick connection to a radio specific SWC interface. No additional Diode 1N4005 or equivelant New High connections are necessary other than radio control connections. Plug the radio Current Output specific SWC interface in to this connector and program the radio specific SWC interface for version 2. Do not cut the loops. Refer to the SWC interface instruction manual for the radio specific control function programming order. 7. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs. For the most current and Up-to-Date application guide please visit www.pac-audio.com 7-19-10 Pacific Accessory Corporation - Santa Ana, CA 92705 techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com Using the VES & Reverse Camera (if equipped) Vehicles equipped with a DVD player built into the rear screen assembly: The C2R-CHY4 will allow the VES DVD player and rear screen to function as if the factory radio were present. A/V will be passed from the factory DVD player to the rear screen and audio can be heard through the headphones. A/V cannot be passed from the factory DVD player to the aftermarket head unit. Vehicles equipped with a stand alone VES DVD Player: The C2R-CHY4 will allow the VES DVD player and rear screen(s) to function as if the factory radio were present. A/V will be passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones. A/V can also be fed from the VES DVD player into an aftermarket head unit (head unit must support A/V in) with the use of the CHYRVD. Vehicles not equipped with a VES DVD Player (rear screen(s) only): In this application the CHYRVD must be used in order to feed A/V into the factory screen(s) from an aftermarket head unit (head unit must support A/V out). With the CHYRVD, A/V will be passed from the aftermarket head unit to the rear screen(s) and audio can be heard through the headphones. If you wish to retain the Auxiliary inputs on the rear of the console you must disconnect the factory wires from the auxiliary input then connect and run your own RCAs into the aftermarket head unit. Vehicles equipped with a Reverse Camera: In order to retain the factory reverse camera the CHYRVD must be used to feed video into the aftermarket head unit (head unit must support reverse camera input). DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-CHY4 be held liable for consequential damages sustained in connection with the C2R-CHY4. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the C2R-CHY4 other than its replacement. 7-19-10 Pacific Accessory Corporation - Santa Ana, CA 92705 techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com