Download Carel Application geothermal heat pumps management User Manual
Transcript
Smart HP Application geothermal heat pumps management Part No. FLSTDmHPGE User Manual Integrated Control Solutions & Energy Savings +030220741 Smart HP – rel. 1.0 - 05/09/2008 1 +030220741 Smart HP – rel. 1.0 - 05/09/2008 2 damages of any type, regardless if these are contractual, extra-contractual, or due to negligence or other responsibility on installation, use, or impossibility to use the product, even if CAREL or its subsidiaries/affiliates have been advised of the possibility of damages. CAUTION DISPOSAL CAREL develops its products based on the company's multiple decade experience in the field of HVAC, on continuous investment in product technology innovation, on rigorous quality processes and procedures with in-circuit tests and 100% functional tests on all products, and on the most innovative production technologies available on the market. CAREL and its subsidiaries/affiliates, however, do not guarantee that all of the features of the product and software included will meet the requirements of the final application, even if they are manufactured with state-of-the-art technology. The customer (manufacturer, designer or installer of the final equipment) assumes all responsibility and risk regarding product configuration to obtain the results expected upon the final specific installation and/or equipment. Under these circumstances, unless other agreements have been made, CAREL can act as a consultant for the success of the final unit/application start-up, but under no conditions can CAREL be held responsible for the correct operation of the final equipment/installation. USER INFORMATION FOR THE CORRECT DISPOSAL OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). In regard to European Directive 2002/96/EC and Italian legislation dated 27 January 2003 and the current relative national legislation, we inform you that: • There exists the obligation to not dispose of WEEE with municipal waste and to perform, for separate collection for these wastes. • Public or private collection systems must be used for disposal as required by local law. Equipment at the end of its life-time may also be returned to the distributor upon the purchase of new, similar equipment. • This equipment may contain hazardous substances. Improper use or disposal may have negative effects on human health and the environment. • The symbol (crossed-out wheeled bin) provided on the product, its packaging, and on the instruction sheet indicate that the equipment entered the market after 13 August 2005 and is subject to separate collection. • Should the electric and electronic equipment be disposed of incorrectly, the sanctions established by the current local laws are applicable. CAREL's product is a high-tech product, whose function is specified in the technical documentation supplied with the product. The documentation can also be downloaded prior to purchase from the internet site www . CAREL . com. Every CAREL product, in relation to its advanced technical level, requires phases for qualification / configuration /programming / commissioning in order to best operate in the specific application. The lack of this design phase, as indicated in the User Manual, can result in malfunction of the final product for which CAREL cannot be held responsible. Only qualified personnel may install or perform technical assistance on this product. The final customer must use the product within the limits of the modes described in product documentation. Without excluding the customer from the due observance of the additional warnings illustrated in this manual, which must be observed at all times, the following warnings must be observed for every CAREL product: • Avoid getting the electronic circuits wet. Rain, humidity, all liquids and condensate contain corrosive minerals that my damage the electronic circuits. The product must be used and stored in areas the meet the temperature and humidity limits specified in the User Manual. • Do not install the equipment in extremely hot areas. Very high temperatures may reduce the life-time or damage of electronic equipment. Plastic parts may deform or melt. The product must be used and stored in areas the meet the temperature and humidity limits specified in the User Manual. • Do not attempt to open the device except according to the method described in the User Manual. • Do not drop, impact, or shake the device as the internal circuits and mechanisms may be irreparably damaged. • Do not use corrosive chemicals, solvents or harsh detergents to clean the device. • Do not use the product in application environments other than those specified in the technical manual. All of the above listed recommendations are also valid for controllers, serial boards, programming keys, or any other accessory in the CAREL product offering. CAREL has a policy of continuous development. Thus, CAREL reserves the right to make any changes and/or improvement to any of the products described in this document without prior notice. The technical data in this manual may be changed without prior notice. ICON KEY CAREL's responsibility for its products is outlined in CAREL's general sales terms that are provided on the Internet site www . CAREL . com and/or by specific customer agreements. In particular, within the limits of the applicable legislation, under no terms will CAREL, its employees, or its subsidiaries/affiliates be responsible for any losses in profits or sales, loss of data or information, costs for replacement goods or services, damages to things or individuals, interruptions in business; or direct, indirect, accidental, capital, coverage, punitive, special and/or consequential +030220741 Smart HP – rel. 1.0 - 05/09/2008 NOTE: to place special attention on important subjects, especially for the practical use of the various product functions. CAUTION: informs the user of critical topics for the use of the product. TUTORIAL: accompanies the user through simple example configurations of the more common settings. 3 +030220741 Smart HP – rel. 1.0 - 05/09/2008 4 INDEX 1. INTRODUCTION .............................................................................................................................................................................................................................. 7 Main Characteristics.................................................................................................................................................................................................................. 7 Parts and Accessories ............................................................................................................................................................................................................... 8 I/O Configurations - Unit Type (Default) ........................................................................................................................................................................... 8 HARDWARE CHARACTERISTICS AND INSTALLATION.......................................................................................................................................................... 15 2.1 Characteristics of pCO3 Board .............................................................................................................................................................................................. 15 2.2 Installation................................................................................................................................................................................................................................. 16 START UP.........................................................................................................................................................................................................................................20 3.1 pCO Manager (Winload)....................................................................................................................................................................................................... 20 3.2 SmartKey ................................................................................................................................................................................................................................... 21 3.3 First Start Up.............................................................................................................................................................................................................................21 USER INTERFACE ...........................................................................................................................................................................................................................23 4.1 Graphic terminal...................................................................................................................................................................................................................... 23 4.2 Display ....................................................................................................................................................................................................................................... 23 MENU DESCRIPTION....................................................................................................................................................................................................................25 5.1 A. On-Off/Mode .............................................................................................................................................................................................................. 25 5.2 B. Setpoint ........................................................................................................................................................................................................................ 25 5.3 C. Time bands.................................................................................................................................................................................................................. 26 5.4 D. Inputs/Outputs........................................................................................................................................................................................................... 26 5.5 E. Alarm Log..................................................................................................................................................................................................................... 27 5.6 F. Change Unit................................................................................................................................................................................................................. 27 5.7 G. Service..........................................................................................................................................................................................................................27 5.8 H. Manufacturer .............................................................................................................................................................................................................. 28 FUNCTIONS .................................................................................................................................................................................................................................... 29 6.1 Compressor Management .................................................................................................................................................................................................... 29 6.2 EVD400 Electronic Valve Management.............................................................................................................................................................................. 29 6.3 Antifreeze Function.................................................................................................................................................................................................................29 6.4 Control of the installation Water and the Geothermal Circuit...................................................................................................................................... 29 6.5 Humidify and Dehumidify Management........................................................................................................................................................................... 30 6.6 Domestic Water Temperature Control and Anti-Legionnaire Function...................................................................................................................... 30 6.7 Solar Panel Management ...................................................................................................................................................................................................... 31 6.8 Temperature Compensation ................................................................................................................................................................................................ 31 6.9 Management of the zones using the Serial probes or Clima ....................................................................................................................................... 31 6.10 Recovery Fans ..........................................................................................................................................................................................................................31 PARAMETER TABLE .......................................................................................................................................................................................................................32 VARIABLES SENT TO THE SUPERVISOR................................................................................................................................................................................... 49 ALARMS............................................................................................................................................................................................................................................ 53 9.1 Alarm Management................................................................................................................................................................................................................53 9.2 Alarm Log.................................................................................................................................................................................................................................. 53 9.3 Alarm Table...............................................................................................................................................................................................................................53 1.1 1.2 1.3 2. 3. 4. 5. 6. 7. 8. 9. +030220741 Smart HP – rel. 1.0 - 05/09/2008 5 +030220741 Smart HP – rel. 1.0 - 05/09/2008 6 1. INTRODUCTION 1.1 Main Characteristics Smart HP is CAREL's new solution for the management of geothermal heat pumps. 3 The Smart HP software installed in the programmable pCO board allows you to: • Control the heat pump • Produce hot water with the integration of thermal solar panels • Manage six different rooms organized on two schedulers/zones • Use the electronic expansion valve • Use serials to make installations "modular" • Completely customise the installation by selecting the control board from among the different sizes available (Small, Medium and Large) based on your specific needs • Connect the installations to BMS systems. • Save energy and consequently money thanks to the integration of the unit + installation management. • Improve system management, which can be set using a simple graphic user interface (pGD1). 3 This CAREL product is certified by the well-tested and proven reliability of the pCO control board. Fig. 1.a Key 1 2 3 4 5 6 7 Controller System User Interface Connection to BMS Driver and electronic expansion valve Zone Control, ex. Clima or Serial Probes ... Compressor/Pump Inverter and Speed Control A few system probes +030220741 Smart HP – rel. 1.0 - 05/09/2008 7 1.2 Parts and Accessories 3 The figure below shows the system architecture formed by the pCO programmable platform on which the Smart HP application and its components and accessories will be installed. Fig. 1.b Key 1 2 3 4 5 6 7 8 9 Description 3 Small, Medium, Large pCO Controller board pDG1 panel or wall installation + telephone line Electronic expansion valve driver Wall probe with serial output Clima Environmental thermostat/humidistat Temperature sensors Pressure sensors Serial board for Field-Bus Serial board for BMS Part No. PCO3000A*0 / PCO3000B*0 PGD1000**0 + S90CONN00* EVD0000440 + E2V**BS*00 DPW**14000 ADC*000**0 TSC1500030, NTC*****00 SPKT00***0 PCO100FD10 Depends on the supervisor connected 1.3 I/O Configurations - Unit Type (Default) From the main menu, using the submenus dedicated to the manufacturer, you can use the "Configure unit Type" parameter Æ ), to select the I/O configuration type from the default list. Smart HP offers six different pre-loaded ( configurations that can be selected using the abovementioned parameter. All of the units operate with water/water. Type Hardware 1 pCO Small Description Installation Control Compressors Reversible 3 Heating + ACS 1 mixing zone 1 on/off 2 pCO Small NO 3 Heating + ACS + High temperature desuperheater 1 mixing zone 1 mixing zone + room T+H probe 1 mixing zone + room T+H probe 1 mixing zone + room T+H probe 1 mixing zone + room T+H probe 1 on/off NO 3 pCO Medium 2 on/off NO 4 pCO Medium 2 on/off SI Gas side 5 pCO Medium + EVD400 2 on/off SI Gas side 6 pCO Medium + EVD400 2 on/off SI Gas side 3 3 3 3 Heating + ACS + High temperature desuperheater Heating / Cooling + ACS + High Temperature Desuperheater Heating / Cooling + ACS + High Temperature Desuperheater Heating / Cooling + ACS + High Temperature Desuperheater + Solar Heater Integration The following pages show the schematic drawings for the different configuration pre-loaded on the Smart HP. +030220741 Smart HP – rel. 1.0 - 05/09/2008 8 1.3.1 Unit “Type 1”: Water-Water Unit, Only Hot Fig. 1.c Analogue Inputs No. Description Geothermal Circuit Outlet B1 Temperature Geothermal Circuit Return Temperature B2 Domestic Water Control B3 Temperature B4 Mixing Circuit Outlet Temperature B5 Installation Return Temperature Analogue Inputs Via RS485 Bus No. Description Sn.B1 Outside Temperature Probe Sn.B2 Outside Humidity Probe +030220741 Smart HP – rel. 1.0 - 05/09/2008 Digital Inputs No. Description ID1 Geothermal Field Side Flow Switch ID2 Compressor 1 Thermal Overload Switch ID3 High Pressure Switch ID4 Low Pressure Switch Unit/Installation Pump Thermal Overload ID5 Switch ACS Storage Heater Thermal Overload Switch ID6 ID7 Furnace/Heater Alarm addition ID8 On-Off Remote 9 Analogue Outputs No. Description Y1 Y2 Modulating Geothermal Pump Y3 3-way Installation valve Y4 Digital Outputs No. Description NO1 Compressor 1 NO2 Geothermal pump NO3 Primary circuit pump Domestic Water/Installation Deviation NO4 Valve NO5 Mixing circuit pump NO6 Integrated Furnace/Heater Installation ACS Storage Electric NO7 Heater NO8 General Alarm 1.3.2 Unit “type 2”: Water-water Unit, Only Hot Water with High Temperature Circuit from Desuperheater Fig. 1.d Analogue Inputs No. Description B1 Geothermal Circuit Outlet Temperature B2 Geothermal Circuit Return Temperature B3 Domestic Water Control Temperature B4 Mixing Installation Outlet Temperature B5 Installation Return Temperature Analogue Inputs Via RS485 Bus No. Description Sn.B1 Outside Temperature Probe Sn.B2 Outside Humidity Probe +030220741 Smart HP – rel. 1.0 - 05/09/2008 Digital Inputs No. Description ID1 Geothermal Field Side Flow Switch Compressor 1 Thermal Overload ID2 Switch ID3 High Pressure Switch ID4 Low Pressure Switch Unit/Installation Pump Thermal ID5 Overload Switch ACS Storage Heater Thermal Overload Switch ID6 ID7 Furnace/Heater Alarm addition ID8 On-Off remote 10 Analogue Outputs No. Description Y1 Modulating Domestic Water Pump Y2 Modulating Geothermal Pump Y3 3-way Installation valve Y4 Digital Outputs No. Description NO1 Compressor 1 NO2 Geothermal Pump NO3 Primary Circuit Pump NO4 Modulating Domestic Water Pump NO5 Mixing Circuit Pump NO6 Installation Integrated Furnace/Heater NO7 ACS Storage Electric Heater NO8 General Alarm 1.3.3 Unit “Type 3”: Water-Water Unit, Only Hot, 2 Compressors, Single Circuit Fig. 1.e Analogue Inputs No. Description B1 Geothermal Circuit Outlet Temp. B2 Return Circuit Outlet Temp. B3 Domestic Water Control Temperature B4 Mixing Installation Outlet Temperature B5 Installation Return Temperature B6 Outside Air Temp. B7 High Pressure Transducer B8 High Pressure Transducer Analogue Inputs Via RS485 Bus No. Description Sn.B1 Outside Temperature Probe Sn.B2 Outside Humidity Probe Sn.Bx Room 1 Temperature Probe Sn.By Room 1 Humidity Probe Up To Six Rooms From Probes +030220741 Smart HP – rel. 1.0 - 05/09/2008 Digital Inputs No. Description ID1 Geothermal Field Side Flow Switch ID2 Compressor 1 Thermal Overload Switch ID3 High Pressure Switch Comp. 1 ID4 Low Pressure Switch Geothermal Circuit Pump Thermal Overload ID5 Switch Primary/Mixing Circuit Pump Thermal ID6 Overload Switch ID7 Furnace/Heater Alarm addition ID8 On-Off Remote ID9 Compressor 2 Thermal Overload Switch ID10 High Pressure Switch Comp. 2 Domestic Water Pump Thermal Overload Switch ID11 ID12 Primary Circuit Flow Switch ID13 Humidifier/Dehumidifier Alarm ACS Storage Heater Thermal Overload ID14 Switch 11 Analogue Outputs No. Description Y1 Modulating Domestic Water Pump Y2 Modulating Geothermal Pump Y3 3-way Installation valve Y4 Humidifier Digital Outputs No. Description NO1 Compressor 1 NO2 Geothermal Pump NO3 Primary Circuit Pump NO4 Domestic Water Circuit Pump NO5 Mixing Circuit Outlet Pump NO6 Installation Integrated Furnace/Heater NO7 ACS Storage Electric Heater NO8 General Alarm NO9 Compressor 2 NO10 Recovery Fan NO11 Dehumidifier NO12 Control Zone 1 NO13 Control Zone 2 1.3.4 Unit “Type 4”: Reversible Water-water Unit with 2 Compressors, Single Circuit Fig. 1.f Analogue Inputs No. Description B1 Geothermal Circuit Outlet Temp. B2 Return Circuit Outlet Temp. B3 Domestic Water Control Temperature B4 Mixing Installation Outlet Temperature B5 Installation Return Temperature B6 Primary Installation Outlet Temperature B7 High Pressure Transducer B8 Low Pressure Transducer Analogue Inputs Via RS485 Bus No. Description Sn.B1 Outside Temperature Probe Sn.B2 Outside Humidity Probe Sm.Bx Room 1 Temperature Probe Sm.By Room 1 Humidity Probe Up To Six Rooms From Serial Probes Or Clima +030220741 Smart HP – rel. 1.0 - 05/09/2008 Digital Inputs No. Description ID1 Geothermal Field Side Flow Switch ID2 Compressor 1 Thermal Overload Switch ID3 High Pressure Switch Comp. 1 ID4 Low Pressure Switch Geothermal Circuit Pump Thermal Overload Switch ID5 Primary/Mixing Circuits Pump Overload ID6 Switch ID7 Furnace/Heater Alarm addition ID8 On-Off Remote ID9 Compressor 2 Thermal Overload Switch ID10 High Pressure Switch Comp. 2 Domestic Water Pump Thermal ID11 Overload Switch ID12 Primary Circuit Flow Switch ID13 Humidifier/Dehumidifier Alarm ACS Storage Heater Thermal Overload Switch ID14 12 Analogue Outputs No. Description Y1 Modulating Domestic Water Pump Y2 Modulating Geothermal Pump Y3 3-way Installation valve Y4 Humidifier Digital Outputs No. Description NO1 Compressor 1 NO2 Geothermal Pump NO3 Primary Circuit Pump NO4 Domestic Water Circuit Pump NO5 Mixing Circuit Outlet Pump NO6 Installation Integrated Furnace/Heater NO7 ACS Storage Electric Heater NO8 General Alarm / Recovery Fan NO9 Compressor 2 NO10 Cycle Reversal 4-way Valve NO11 Dehumidifier NO12 Zone 1 NO13 Zone 2 1.3.5 Unit “Type 5”: Reversible Water-water Unit with 2 Compressors, Single Circuit with Electronic Expansion Valve Fig. 1.g Analogue Inputs No. Description B1 Geothermal Circuit Outlet Temp. B2 Geothermal Circuit Return Temperature B3 Domestic Water Control Temperature B4 Exhaust Gas Temp. (Comp. Outlet) B5 Installation Return Temperature B6 Outside Air Temp. B7 Primary Installation Outlet Temperature B8 Mixing Installation Outlet Temperature EVD 400 Analogue Inputs No. Description S1 Low Pressure Transducer S2 High Pressure Transducer S3 Compressor Intake Gas Temp. Analogue Inputs Via RS485 Bus No. Description Sn.B1 Outside Temperature Probe (Opt.) Sn.B2 Outside Humidity Probe (Opt.) Sm.Bx Room 1 Temperature Probe Sm.By Room 1 Humidity Probe Up To Six Rooms From Serial Probes Or Clima +030220741 Smart HP – rel. 1.0 - 05/09/2008 Digital Inputs No. Description ID1 Geothermal Field Side Flow Switch ID2 Compressor 1 Thermal Overload Switch ID3 High Pressure Switch Comp. 1 ID4 Low Pressure Switch Geothermal Circuit Pump Thermal ID5 Overload Switch Primary/Mixing Circuits Pump Overload ID6 Switch ID7 Furnace/Heater Alarm addition ID8 On-Off remote ID9 Compressor 2 Thermal Overload Switch ID10 High Pressure Switch Comp. 2 Domestic Water Pump Thermal Overload Switch ID11 ID12 Primary Circuit Flow Switch ID13 Humidifier/Dehumidifier Alarm ACS Storage Heater Thermal Overload ID14 Switch 13 Analogue Outputs No. Description Y1 Modulating Domestic Water Pump Y2 Modulating Geothermal Pump Y3 3-way Installation valve Y4 Humidifier EVD400 Analogue Outputs No. Description EVD EVD Control Impulse Output Digital Outputs No. Description NO1 Compressor 1 NO2 Geothermal Pump NO3 Primary Circuit Pump NO4 Domestic Water Circuit Pump NO5 Mixing Circuit Pump NO6 Installation Integrated Furnace/Heater NO7 ACS Storage Heater NO8 General Alarm / Fan(s) Recovery NO9 Compressor 2 NO10 Cycle Reversal 4-way Valve NO11 Dehumidifier NO12 Zone 1 NO13 Zone 2 1.3.6 Unit “Type 6”: Reversible Water-water Unit with 2 Compressors, Single Circuit, Electronic Expansion Valve and Solar Heating Installation Fig. 1.h Analogue Inputs No. Description B1 Geothermal Outlet Temp. B2 Return Outlet Temp. B3 Domestic Water Control Temperature B4 Mixing Circuit Outlet Temp. B5 Installation Return Temperature B6 Outside Temp. B7 Primary Circuit Outlet Temp. B8 ACS Tank Lower Temp. B9 Solar Manifold 1 Temp. B10 Solar Manifold 2 Temp. B9 and B10 must be connected to PT1000 probes EVD 400 Analogue Inputs No. Description S1 Low Pressure Transducer S2 High Pressure Transducer S3 Compressor Intake Gas Temp. . Analogue Inputs Via RS485 Bus No. Description Sn.B1 Outside Temperature Probe (Opt.) Sn.B2 Outside Humidity Probe (Opt.) Sm.Bx Room 1 Temperature Probe Sm.By Room 1 Humidity Probe Up To Six Rooms From Serial Probes +030220741 Smart HP – rel. 1.0 - 05/09/2008 Digital Inputs No. Description ID1 Geothermal Field Side Flow Switch ID2 Compressor 1 Thermal Overload Switch ID3 High Pressure Switch Compressor 1 ID4 Low Pressure Switch Geothermal Pump Thermal Overload Switch ID5 Primary Circuit Pump Thermal Overload ID6 Switch Installation Integrated Furnace/Heater ID7 Alarm ID8 On-Off Remote ID9 Compressor 2 Thermal Overload Switch ID10 High Pressure Switch Compressor 2 Domestic Water Pump Thermal Overload Switch ID11 ID12 Primary Circuit Flow Switch ID13 Humidifier/Dehumidifier Alarm ACS Storage Heater Thermal Overload ID14 Switch Mixing Circuit Pump Thermal Overload ID15 Switch ID16 Dehumidifier Alarm Solar Circuit Pump 1 Thermal Overload Switch ID17 Solar Circuit Pump 2 Thermal Overload ID18 Switch 14 Analogue Outputs No. Description Y1 Modulating Domestic Water Pump Y2 Modulating Geothermal Pump Y3 3-way Installation valve Y4 Humidifier Y5 Y6 EVD400 Analogue Outputs No. Description EVD EVD Control Impulse Output Digital Outputs No. Description NO1 Compressor 1 NO2 Geothermal Pump NO3 Primary Circuit Pump NO4 Domestic Water Circuit Pump NO5 Mixing Circuit Pump NO6 Installation Integrated Furnace/Heater NO7 ACS Storage Heater NO8 General Alarm NO9 Compressor 2 NO10 Cycle Reversal 4-way Valve NO11 Dehumidifier NO12 Control Zone 1 NO13 Control Zone 2 NO14 Recovery Fan NO15 Solar Circuit Pump 1 Control NO16 Solar Circuit Pump 2 Control NO17 NO18 2. HARDWARE CHARACTERISTICS AND INSTALLATION 2.1 Characteristics of pCO3 Board Fig. 2.a Key 1 2 3 4 5 6 7 Power supply connector Yellow LED indicating power supply active and three status LEDs Additional power supply for terminal and 0-5 V ratiometric probes Universal analogue inputs: NTC 0 - 1 V, 0 - 5 V - ratiometric, 0 -10 V, 0 -20 mA, 4 -20 mA Passive analogue inputs: NTC, PT1000, ON/OFF Analogue outputs: 0 -10 V Digital inputs, 24 V AC/V DC 8 Digital inputs: 230 V AC or 24 V AC/V DC 9 10 11 Connector for display terminal (external panel with direct messages) Connector for standard terminal in pCO series and for download of application program Relay digital outputs 12 13 14 15 16 Connector for I/O expansion board Local pLAN network connector Flap to insert the supervision and telemaintenance option Flap to insert the Field Card option Built-in terminal (LCD, keys and LED). Models e Characteristics No. Analogue Inputs No. Digital Inputs No. Analogue Outputs No. Digital Outputs Modbus RTU/CAREL Protocol LonWorks Protocol BACnet Ethernet Protocol BACnet MS/TP Protocol http/FTP/SNMP Protocol Setup for modem, GSM modem, SMS 3 G, G0 +Vterm, GND, +5 VREF B1, B2, B3, GND, +VDC e B6, B7, B8, GND B4, BC4, B5, BC5 e B9, BC9, B10, BC10 VG, VG0, Y1, Y2, Y3, Y4 e Y5, Y6 ID1, ID2, ID3, ID4, ID5, ID6, ID7, ID8, IDC1, e ID9, ID10, ID11, ID12, IDC9 e ID17, ID18, IDC17 ID13H,ID13, IDC13, ID14, ID14H e ID15H, ID15, IDC15, ID16, ID16H C1, NO1, NO2, NO3, C1 e C4, NO4, NO5, NO6, C4 e C7, NO7, C7 e NO8, C8, NC8 e C9, N09, N10, NO11, C9 e NO12, C12, NC12 e NO13, C13, NC13 e NO14, C14, NC14, NO15, C15, NC15 e C16, NO16, NO17, NO18, C16 E-, E+, GND Rx-/Tx-, Rx+/Tx+, GND 3 pCO SMALL 5 8 4 8 PCOS004850 PCO10000F0 PCO1000WB0 PCO1000BA0 PCO1000WB0 PCO100MDM0 pCO MEDIUM 8 14 4 13 3 pCO LARGE 10 18 6 18 Product Certifications: IEC EN 50155: “Railway applications. Electronic equipment used on rolling stock”; UL 873 and C22.2 No.24-93: “Temperature-indicating and regulating equipment”; and Regulation EC 37/2005 dated 12 January 2005. In particular, if the electronic control is equipped with CAREL standard NTC probes, it is compliant with EN 13485, “ Thermometers for measuring the air and product temperature for the transport, storage and distribution of chilled, frozen, deep-frozen/quick-frozen food and ice cream. Tests, performance, suitability”. +030220741 Smart HP – rel. 1.0 - 05/09/2008 15 2.2 Installation 2.2.1 How to Install • Caution: Environmental Conditions Avoid installing the pCO board and terminal in areas with the following conditions: y Temperature and humidity do not comply with the values for operation of the product y Strong vibrations or impacts; y Exposure to harsh and polluted atmosphere (ex. sulphuric and ammonia gasses, salt fogs, fumes) with consequential corrosion and/or oxidation y High levels of magnetic and/or radio frequency interference (therefore avoid installation of the units near transmitting antennas) y Exposure of the pCO board to direct sunlight and other weather conditions y Ample and rapid environmental temperature changes y Areas containing explosives or mixes of flammable gasses y Exposition to dust (formation of corrosive layers with resulting oxidation and reduction of insulation) • • • • • • • Location of the instrument inside the panel The position of the instrument inside the electrical cabinet must be selected to ensure consistent physical separation of the instrument from power parts (solenoids, teleroutors, drives, inverters, etc.) and from the cables connected to them. Positioning the instrument too near these types of parts may lead to random malfunctions that are not immediately detectable. The structure of the panel must allow correct passage of cooling air. 2.2.2 • • • Do not press on screwdriver too hard when fastening the cables to the terminals to avoid damaging the pCO controller. For applications subject to strong vibrations (1.5 mm pk-pk 10/55 Hz) we recommend fastening the cables connected to the pCO with clamps at a distance of about 3 cm from the connectors. If the product is installed in an industrial environment (application of EN 61000-6-2) the length of the connections must be less than 30 m. All very low voltage connections (analogue and 24 V AD/ V DC digital inputs, analogue outputs, serial bus connections, and power sources) must have reinforced, double insulation compared to the network. In residential areas, the cable connecting the pCO controller and the terminal must be shielded. There is no limit to the number of cables that can be inserted in a single terminal. The only limitation regards the maximum power in a single terminal: this must not exceed 8 A. The maximum cross-section of the cable that can be inserted in a terminal is 2.5 sq. mm (12 AWG). The maximum value of the twisting moment (or tightening torque) used to tighten the terminal screw is 0.6 Nm. Installation must be performed according to the current laws and norms in the country where the equipment is used. For safety reasons, the equipment must be set inside an electric panel so that the only accessible part is the display and the control keypad. Should the equipment malfunction, do not attempt to repair it; send it back to CAREL. How to Perform Cabling Caution: when performing the cabling "physically" separate the power portion from the command portion. Usually, if these cables are near each other it leads to problems of induced disturbances, or over time, malfunction and/or damage of the components. Ideal conditions are obtained by preparing the location for these to circuits in two separate cabinets. At times this is not possible. It is then necessary to position the power parts in a distinctly separate area inside the same panel than the control parts. For control signals, we recommend using shielded cables with braided wires. Should control cables need to cross power cables, the intersection must be as close as possible to right angles, avoiding in all cases that control cables be positioned parallel to power cables. CAREL recommends paying careful attention to the following warnings: • • • • • Anchoring the pCO Board 2.2.3 The pCO controller is to be installed on a DIN rail. To fasten it to the DIN rail, position the device on the rail and push on it lightly. The click of the tabs on the back confirm that it is fastened on the rail. To dismount, simply use a screwdriver as a lever on the release holes of the same tabs to lift them up. The tabs are held in place by self-closing springs. 2.2.4 Power Supply 3 Power supply for the pCO board (controller with terminal connected): 28 - 36 V DC + 10/- 20 % or 24 V AC + 10/- 15 % 50-60 Hz Maximum absorption P= 15 W (DC power source), P= 40 VA (AC power source). y Electric power source voltage other than that listed may seriously damage the system. y When installing, we recommend using a 50 VA Class II transformer, to power a single pCO controller. y We recommend separating the power supply to the pCO control and the terminal (or more than one pCO and terminals) from the power supply of the other electric devices (counters and other electromechanical components) within the electric panel. y Should the transformer secondary be earthed, check that the earth wire is connected to the G0 terminal. This must be performed for all devices connected to the pCO. y If more than one pCO board connected to a pLAN network is powered, make certain that the G and G0 references are respected (the G0 reference must be maintained for all boards). y A yellow LED indicates the presence of power supply tot he pCO board. Use cable ends suitable for the terminals used. Loosen each screw and insert the cable ends. Then tighten the screws. When all steps have been completed, lightly pull on the cables to ensure they have been tightened correctly. Separate the cables from the probes, digital inputs, and serial lines as much as possible from cables with inductive loads and power in order to avoid any possible electromagnetic disturbances. Never position power cables and probe cables in the same ducts (including those for electrical cables). Avoid installing the probe cables near power devices (counters, magnetic-thermal devices, or others). Minimize probe cable paths and avoid spiral paths that wind around power devices. Avoid putting fingers near the electronic components on the boards in order to avoid static electric shocks (extremely dangerous) from the operator to the components. Should the power transformer secondary be connected to earth, check that the earth wire corresponds to the wire from the controller that enters the G0 terminal. Make certain that this is true for all of the devices connected to the pCO. +030220741 Smart HP – rel. 1.0 - 05/09/2008 16 2.2.5 Connection of Active Probes with 0 - 10 V Output The inputs must be pre-configured for 0 - 10 V signals from the application program. Control 0 - 10 V Probe Cable 3 pCO GND Reference B1, B2, B3, B6, B7, B8 Signal Connection of the analogue inputs Note: in Smart HP the analogue input configuration is automatically setup based on the type of unit selected. The analogue inputs on the pCO board can be configured for the various probes available on the market: NTC, PT1000, 0…1 V, 0 - 5 V ratiometric, 0 10 V, 0 - 20 mA, or 4 - 20 mA. To select the type of probe used, set the parameter on the user terminal (if equipped with the application program). Connection of Selected Analogue Inputs, such as ON/OFF The pCO controller can be configure some clean, not optoisolated, digital inputs. The inputs must be pre-configured as clean digital inputs from the application program. Control pCO Terminals Digital Input Cable 3 pCO Digit 1 Digit 2 Digit 3 Digit 4 BC4 BC5 BC9 BC10 1 B4 B5 B9 B10 2 Connection of active temperature and humidity probes All of the active temperature and humidity probes in the DP*2 CAREL series configured as 0 - 1 V or 4 - 20 mA can be connected to the pCO board. For temperature probes, use the 4 - 20 mA or NTC configuration as the 0/1 V DC signal is understood to be limited to 0 - 1 V and therefore not always compatible with the standard 10 mV/°C signal from the CAREL probes (negative temperatures or temperatures greater than 100 °C may generate an probe alarm). The inputs must be pre-configured for 0 - 1 V or 4 - 20 mA signals from the application program. Control pCO Probe Description Terminals Terminals GND M Reference +V DC +(G) Power Supply B1, B2, B3, B6, Out H Active Humidity Output 3 pCO B7, B8 B1, B2, B3, B6, Out T Active Temperature Output B7, B8 Remoting Analogue Inputs The cross-section of the cables for remoting the analouge inputs are provided in the following table: 2 2 Cross-Section (mm ) per Type of Input Cross-Section (mm ) per lengths up to 50 m lengths up to 100 m NTC 0.5 1.0 PT1000 0.75 1.5 I (in current) 0.25 0.5 V (in voltage) 1.5 Not Recommended Connection to Universal NTC Temperature Probes All of the analogue inputs are compatible with NTC probes with 2 wires. The inputs must be pre-configured for NTC type signals from the application program in the flash memory. Control pCO Terminals NTC Probe Cable 3 pCO GND, BC4, BC5, BC9, 1 BC10 B1, B2, B3, B4, B5, B6, 2 B7, B8, B9, B10 Note: If the product is installed in an industrial environment (application of EN 61000-6-2) the length of the connections must be less than 30 m. In any case, we recommend not exceeding this length in order to avoid measurement errors. 2.2.6 Connection of the Digital Inputs The pCO controller has digital inputs for connection to safeties, alarms, device statuses, and remote consensus. These inputs are all optoisolated compared to the other terminals and can operate at 24 V AC, 24 V DC and a few at 230 V AC. Connection to the PT1000 Temperature Probes The pCO controller can be connected to PT1000 probes with 2 wires for all high temperature applications. Their operative range is -50 - 200 °C. The inputs must be pre-configured for PT1000 type signals from the application program in the flash memory. Control 3 pCO Note: Separate the cables from the probes and the digital inputs from cables with inductive loads and power in order to avoid any possible electromagnetic disturbances. PT1000 Probe Cable Probe 1 BC4 B4 Probe 2 BC5 B5 Probe 3 BC9 B9 Probe 4 BC10 B10 1 2 Digital Inputs with 24 V AC Power Supply 3 For pCO all inputs can be at 24V AC. The following figure represents one of the most common wiring diagrams for connecting the 24 V AC digital inputs. Connection to the Pressure Probes in Current The pCO can be connected to all active pressure probes in the SPKT****C0 CAREL series or any other pressure probe on the market with 0 - 20 mA or 4 20 mA signal. The inputs must be pre-configured for 0 - 20 mA or 4 - 20 mA signals. Control pCO Terminals Probe Cable Colour Description 3 pCO +V DC Black Power supply B1, B2, B3 White Signal B6, B7, B8 Green Not used Fig. 2.b Connection to Ratiometric 0/5 V Pressure Probes The pCO can be connected to all active pressure probes in the SPKT****R0 CAREL series or any other pressure probe on the market with 0/5 V ratiometric signal. The inputs must be pre-configured for 0/5 V ratiometric signals from the application program. Control pCO Terminals Probe Cable Colour Description 3 pCO +5 V Ref Black Power Supply GND Green Power Supply Reference B1, B2, B3 White Signal B6, B7, B8 +030220741 Smart HP – rel. 1.0 - 05/09/2008 Note: the wiring diagrams provided in these figures, although representing the most common and most simple configurations, do not exclude the possibility of powering the digital inputs separately from the pCO board power supply. In any case, the inputs have only functional insulation compared to the rest of the control. 17 Digital Inputs with 24 V DC Power Supply 3 For pCO all inputs can be at 24V DC. The following figure represents one of the most common wiring diagrams for connecting the 24 V DC digital inputs. Electromechanical Relay Digital Outputs The relays are divided into groups based on the insulation distance. Within each group, the relays have a main insulation between each other and therefore must be exposed to the same voltage (normally 24 V AC or 110 - 230 V AC). On the other hand, among groups insulation is doubled and therefore the groups can be at different voltages. In any case, there is double insulation towards the rest of the control. Version Reference to equally insulated relays Group Group Group Group 1 2 3 4 Group 1-7 8 Composition SMALL MEDIUM 1-7 8 9 - 13 LARGE 1-7 8 9 - 13 14 - 18 Fig. 2.c Relay ID tag data Digital Inputs with 230 V AC Power Supply Up to two groups of inputs are present that can be powered with 230 V AC; each group has two inputs. The groups are double insulated from each other and can refer to different voltages. Within each group, the digital inputs cannot be independent: for example, due to their common terminal, inputs ID15 and ID16 must have the same voltage supply in order to avoid dangerous short circuits and/or be powered at 230 V AC for lower voltage circuits. In any case, the inputs have double insulation compared to the rest of the control. 3 pCO Terminals 3 pCO Certifications SPDT, 2000 VA, 250 V AC, 8A Resistive 2.5 A Resistive, 2A FLA, 12A LRA, 250 V UL873 AC, C300 Pilot Duty (30,000 Cycles) 2A Resistive, 2A Inductive, cosϕ=0.6, EN 60730-1 2(2)A (100,000 Cycles) Solid State Relay (SSR) Digital Outputs The pCO controller can also be equipped with solid state relays (SSR) (for example pCO LARGE part no. PCO300*AL0) for the control of devices that require an unlimited number of manoeuvres that may not be supported by the electromechanical versions. These outputs are dedicated to loads powered at 24 V AC/V DC with maximum power Pmax= 10 W. Input ID13H, ID14H, ID15H, ID16H Summary table of Digital Outputs Based on the Available Versions 3 No. No. SPDT No. Total SSR Reference pCO Terminals SPST Outputs Relay SMALL 7 1 (8) 8 1 (7) MEDIUM 10 3 (8, 12, 13) 13 2 (7, 12) LARGE 13 5 (8, 12, 13, 18 3 (7, 12, 14) o 14, 15) 4 (7, 12, 14, 15) Fig. 2.d Note: the number between parenthesis is the corresponding terminal. For ex.: 8 = N08. The uncertainty range of the trip threshold ranges from 43 to 90 V AC. We recommend using a 100 mA fuse in series with the digital inputs. Remoting Digital Outputs The cross-section of the cables for remoting the digital outputs can be found in the following table. 2 Current (A) AWG Cross-Section (mm ) 20 0.5 2 15 1.5 6 14 2.5 8 Remoting Digital Inputs Caution: do not connect other devices to the IDn inputs. The cross-section of the cables for remoting the digital inputs can be found in the following table. 2 2 Cross-Section (mm ) per lengths Cross-Section (mm ) for lengths up to 50 m up to 100 m 0.25 0.5 If the product is installed in an industrial environment (application of EN 610006-2) the length of the connections must be less than 30 m. Note: If the product is installed in an industrial environment (application of EN 61000-6-2) the length of the connections must be less than 30 m. In any case, we recommend not exceeding this length in order to avoid reading errors. Note: For further information and wiring diagrams, please refer to the dedicated manual for the pCO system (+030220335). 2.2.7 Connection of the Analogue Outputs Connection of the 0 - 10V Analogue Outputs The pCO controller provides 0 - 10 V optoisolated analogue outputs externally powered by 24 V AC/V DC. The table below summarizes the distribution of the analogue outputs based on the available versions. pCO Terminal Reference 3 pCO Terminals SMALL Y1, Y2, Y3, Y4 VG0 MEDIUM Y1, Y2, Y3, Y4 VG0 LARGE Y1, Y2, Y3, Y4, Y5, Y6 VG0 2.2.8 Connection of the Digital Outputs The pCO controller has digital outputs with electromechanical relays to facility assembly. The common terminals for some relays have been grouped together. +030220741 Smart HP – rel. 1.0 - 05/09/2008 18 service port using the EVD4-UI software . Connect the converter (CVSTDUTTL0 or CVSTD0TTL0) to the serial service port and a PC with a USB or serial RS232 port. Then, launch the ‘‘EVD4_UI Address’’ connection as described in the EVD400 valve manual (+030220225) and set the Net address parameter. In the space on the top right of the interface, the new value will appear under ‘‘Network address’’, after pressing the ‘‘READ’’ key. If not modified by the user, the Net Address parameter will have the following default values: 2.2.9 Installation of the Serial Field Bus for Connection of Serial Probes or Clima The serial probes and Clima terminal must be installed according to the following diagram and require the PCO100FD10 field bus be inserted in the dedicated slot (“Field-Bus”). The Clima terminal also requires the IROPZ48500 converter. Both must be powered with 24 V AC voltage. Net address 2 30 32 1 EVD000*40* and EVD000*43* EVD000*41* and EVD000*44* EVD000*42* and EVD000*45* EVD0001460 Following is a list describing the connectors supplied with EVD000*4*0 or purchase separately EVDCON0001 for EVD000*4*1. Note: if the change in address is performed using the pLAN o Modbus®protocol, the ‘‘Network address’’ item is updated when the device is turned off and turned back on. Note: it is possible to set the network address of the EVD400 valve using the CAREL ComTool software. Note: for further information and wiring diagrams, please refer to the dedicated manual for the pEVD400 system (+030220225). 2.2.11 Remoting terminal with pLAN Network If the pCO boards are connected to a pLAN network, the terminal can be remoted up to 50 m away using a telephone wire, whereas, if a shielded pair cable, TCONN6J000, and separate power supply are used, it can be remoted up to 500 m. Fig. 2.e Note: if the terminal is used in a residential application, the cable must always be shielded. The maximum distance between the pCO and the user terminal is shown in the following table: Setup of Parameters and Addresses The default values (Baud rate = 19200, Stop bit = 2, Time out = 300 ms, Priority = none) are displayed and can be modified if required on the screen Gfc02. The settings to be made on the Clima terminal are the parameter SEr = 5 and the parameter Adr = 1- 6 (of addressing). For the DP probes, on the other hand, it is necessary to set dip switches 6, 7 and 8 (6 = OFF, 7 = ON, 8 = ON) and the parameter Adr = 128 - 133. Cable Type Telephone Shielded AWG24 cable Shielded AWG20/22 cable Note: For further information and for the wiring diagrams, please refer to the manual dedicated to the Clima terminal (+030220640) and the manual for the DP serial probes (+030220660). Installation of EVD400 Valve Driver 2.2.10 For connection in pLAN network of the EVD400 valve with pCO board, please refer to the figure below: Distance to Power Power Supply Supply 50 m Taken from pCO (150 mA) 200 m Taken from pCO (150 mA) 500 m Separate Power Supply Using TCONN6J000 3 The maximum distance between two pCO with shielded cable is AWG 20/22l, equal to 500 Note: For further information and wiring diagrams, please refer to the dedicated manual for the pCO system (+030220335). Fig. 2.f Setting Network Address The functional parameters of the EVD400, including the network address, are stored in the EEPROM. To modify the values, you must access the serial +030220741 Smart HP – rel. 1.0 - 05/09/2008 19 3. START UP The following systems allow you to update and install the Smart HP application on the pCO board: • pCO Manager (Winload) • SmartKey programming key parameters Loading/downloading logs Loading/downloading Flash NAND (pCO3) 3.1 pCO Manager (Winload) REMOTE (not via pLAN) BMS Serial Load Boot and BIOS NO Loading application and YES parameters Loading/downloading logs YES Loading/downloading NO Flash NAND (pCO3) It is possible to update the resident software in all CAREL 16-bit controllers on the pCO Sistema board (see the manual dedicated tot he pCO system) using a PC. For this reason, CAREL supplies the WinLoad32.exe program and a serial converter with RS485 output (part no. CVSTDUTLF0) for connection tot he pCO. It is necessary to install the required driver on the PC, also released by CAREL. Installation of the WinLoad32.exe program is included in the entire “1Tool” program suite, inside the pCO Manager program, or separately from the Internet site http : // ksa . CAREL . com in the “Download Æ Support Æ Software Utilities” section. In addition to the WinLoad32.exe program, installation includes the user manual. The pCO controller can be connected to the PC directly using the RS485 serial port used for “pLAN” connection, or using the BMS serial port with RS485 serial board, optionally used for the “supervisor” connection. Using the BMS serial port and the optional RS232 serial board, it is possible to connect the pCO controller to an analogue (PSTN) or GSM modem and thus connect to WinLoad32 by remote. Winload allows communication with all of the programmable controllers in the pCO family. Using this program, it is generally possible to update and download to a PC the 3 BOOT, BIOS, application, file configuration log, with special cases for the pCO controller, using which it is also possible to store files in the new Flash NAND. Let us underscore that generally CAREL DOES NOT RECOMMEND updating the BOOT. CAREL always loads the correct BOOT required for unit's operation directly in production. Only under very special conditions may CAREL request that a user update the BOOT. It is only possible to load the BIOS using the serial pLAN connection. The update of the BIOS causes a change in the unit method, which shifts to a low level. In this particular mode it is not possible to download the log data to a PC or load the application in compressed format. To restore the unit to its normal mode of communication with Winload it is necessary to reset the pCO board after successfully loading the BIOS. Winload will automatically configure for the unit connected. For example, allowing or not the download of a special BIOS version, enabling or not the download of the log configuration, recognising or not if the unit has the possibility to use the greatest possible size of RAM and, therefore, enabling or not the download of an application that takes advantage of the total amount of RAM. In a few cases, however, it is necessary to set a few options, such as, for example, the operative Baud Rate if the pCO to be used has a 14.7 MHz or 16 MHz quartz, using the command line in a normal windows connection to the executable Winload32.exe. In-line help and the record file for changes, “CHANGELOG”, offer help for the user in any case. In general, the sequence for operations to begin communications between Winload in the graphic mode and pCO is the following: • Connect the RS485/USB converter to the PC and to pCO. • Open the Winload program on the PC by double clicking on the icon only after activating any options using the control line. • On the main screen, set the serial port of the PC that is connected to the serial converter and the pLAN address of the pCO board to communicate with. • Power the pCO Controller. • Wait for "on-line" to be indicated on the lower left on the main screen. • At this point, select the proper file on the main page to perform the desired operation. For the “EASYWINLOAD” mode, the automatic loading mode in which the settings are supplied before executing the program, and for remote connection via MODEM, please follow the instructions provided in Winload's on-line Help. The possibilities for download are listed in the following tables: LOCAL Load Boot and BIOS Loading application and pLAN Serial BMS Serial YES YES NO YES +030220741 Smart HP – rel. 1.0 - 05/09/2008 YES YES YES NO YES NO FieldBus Serial NO NO NO NO All of the functions of the Winload32 program are also available in the pCO Manager tool, which includes the Commissioning Tool . Fig. 3.a 3.1.1 Commissioning Tool Required setup on pCO to use the Commissioning Tool: 1) the application uses a screen (Ge_01) through which it is possible to setup the Winload protocol on the BMS serial. 2) If you want to have a remote connection, the system variables regarding the PSTN or GSM modem must be setup correctly. 3) To perform the operations available using the Commissioning Tool it is necessary to connect to the already functioning application. This means that the Winload protocol must be set up in some way (using an application screen or by the supervisor) after the pCO controller has been turned on. If the pCO controller is connected directly to start-up via the pLAN serial port, it enters the Winload mode and under these conditions it is not possible to perform the operations of the Commissioning Tool. 4) If firmware and the application are updated, before using the Commissioning Tool you must reset the pCO board. 5) Once the protocol is correctly setup on the desired serial, it is possible to connect the PC. CAUTION: If you use the BMS OR FIELD BUS serial ports, once the pCO controller is disconnected with a PC command (for example when you move from the PCLoad window to the Commissioning Tool window and vice versa), the pCO controller resets the previous protocol setup on the serial in use. If previously an application was updated, the pCO controller is automatically reset. To reconnect the pCO controller, it is therefore necessary to reset the Winload protocol on the pCO. Memory Limits: The periodic monitoring of the application variables is limited to a maximum of 250 WORDs that can be defined from among all the available memory the application has available. The periodic monitoring of the application variables is limited to a maximum of 50 WORDs that can be defined from among all the available memory the application has available. “One-shot” reading and writing the individual variables does not have address limits. All addresses in the memory reserved by the application of all memories present in the pCO are available: memory X, memory T, memory P, memory E. FieldBus Serial NO YES 20 To change the display address (“Display address setting”) perform the following operations in sequence. Note: for further information regarding the installation and update of software on the pCO controller board, please refer to the on-line help of the pCO Manager program. 1. 3.2 SmartKey 2. The SMARTKEY programming key allows the programming key function to be emulated in parallel in the pCO models for which this function is not available ( XS 3 pCO , pCO ) with the exception of the BOOT, which is not loaded by the SMARTKEY. In particular, the key can clone the content of a pCO and download it to another identical pCO on the first use of the telephone connector of the terminals (the pLAN must be disconnected). This function is available for all pCO, even those without a parallel key. In addition to this mode, the key can also be used to remove the log data from more than one pCO and the download them to a PC. Using the PC, and the “SMARTKEY PROGRAMMER”, the key can be configured to perform specific operations: download of logs, application programming, BIOS programming, etc. For further information, please see the on-line help of the “SMARTKEY PROGRAMMER” program and the SMARTKEY instruction sheet. 3. Press once setting” field. : the cursor will move to the “Display address Select the desired value using and , and confirm it by pressing again. If the selected value is different from the value in memory, the following screen will appear and the new value will be saved to the display's permanent memory. Fig. 3.d If the value of the address to 0, the terminal will communicate with the pCO board using the Local Terminal protocol and the “I/O Board address” field will disappear as it will no longer have a meaning. To modify the list of terminals (private and shared) associated with a pCO board, perform the following operations in sequence: 4. Enter the configuration mode (see above) by pressing and 5. 6. : the cursor will move to the “I/O Board address” Press twice field. Select the address of the pCO board to be modified and confirm by pressing Fig. 3.b , at the same time for at least 5 seconds. . At this point, the pCO controller will start the configuration procedure by sending a screen similar to that shown in the following figure. Note: for further information regarding the installation and update of software on the pCO controller board, please refer to the on-line help of the pCO Manager program. 3.3 First Start Up 3 The first time the pCO board is started up when the Smart HP application is installed, a screen appears from which it is possible to select the program language. Using standard navigation commands, select the language desired and confirm it in order to access the main menu. Fig. 3.e 7. Note: if not selection is made within the time defined by a parameter (in the menu dedicated to the manufacturer), the language selected will be that currently in use. Press once again to the following: : the configuration screen will appear, similar 3.3.1 Addressing the terminal The address of the terminal can be set in a range from 0 to 32. Addresses 1 and 32 are used for the pLAN protocol. Address 0 identifies the Local Terminal protocol, used to perform point-to-point connections without graphics and to configure the pCO controller. The factory-set address is 32. The address of the terminal can be configured only after powering the terminal using the RJ12 Fig. 3.f , and at the connector. To enter the configuration mode, press same time and hold them for at least 5 seconds. The terminal will show a screen that is similar to the following. The cursor will flash in the upper left corner: 8. Modify the terminal configurations as desired. will move the cursor from one field to the other; whereas, and change the value in the current field. The P:xx field displays the address of the selected pCO board (in the example shown in the figure it is board 1). 9. . “Ok?” field, select “Yes” and confirm by pressing During the configuration procedure, if the terminal remains inactive (no keys pressed) for more than 30 seconds, the pCO board will automatically interrupt the procedure without saving any changes made. . Fig. 3.c +030220741 Smart HP – rel. 1.0 - 05/09/2008 To exit the configuration procedure and save the data, select the 21 Caution: if during operation the terminal detects an inactive status of the pCO board that is displaying the output, it completely deletes the display and shows a message similar to the following. Caution: if the settings have not be configured correctly, the text and the images shown on the display will be incorrect and in the wrong order. Fig. 3.g If the terminal detects inactivity on the entire pLAN network, that it does not receive any messages from the network for 10 consecutive seconds, it completely deletes the display and shows the following message: Fig. 3.h 3 3.3.2 Addressing the I/O pCO board To complete the installation procedure, you must set the pLAN address on the 3 pCO. The pCO controllers do not have dip-switches for addressing the pLAN network: the change in the pLAN address is performed using any GD1 terminal. 1. Set the address to 0 on the terminal (please refer to the previous sections for details on how to select this address). 2. Remove the pCO power supply. 3. Remove any pLAN connections to other controllers from the pCO. 4. Connect the terminal to the pCO. 5. Power the pCO controller and at the same time press the UP and ALARM alarm keys on the terminal. After a few seconds, the pCO controller will perform the starting sequence and its display will show a screen similar to the following: Fig. 3.i 6. 7. Once the screen appears, wait 10 seconds and then release the keys. The pCO controller will interrupt the starting sequence and display a configuration screen similar to the following: Fig. 3.l At this point, change the pLAN address suing the terminal. 8. and keys on the : the pCO controller will Confirm the address by pressing complete the starting sequence and will use the specified address. +030220741 Smart HP – rel. 1.0 - 05/09/2008 22 4. USER INTERFACE 4.1 Graphic terminal Smart HP interfaces with the user via pGD1 terminal, in the wall or panel versions, or eventually via the “built-in” display on the pCO board. identifies the three temperatures indicated and therefore: T.DOMESTIC (temp. relative to the domestic water) T.OUTSIDE (outside temp. measured), T.INSTALLATION (temp. of water returned to the primary installation). The request(s) to the compressors are activated at the same time. Activated if there is a request to heat the domestic water. Activated when one of the installation pumps are turned on, with the exception of the solar panel pumps. Fig.4.a Activated if one or more solar panels are installed and active. Activated if the integration system for the installation (ex. heater or furnace) is operating. This terminal, shown in the figure above, is equipped with six keys with the following meanings: - Alarm - Prg - Esc - Up - Down - Enter displays the list of active alarms. Allows you to access the main menu tree. Return to the previous screen. If the and icons are both active at the same tine, only the latter is visible. In the picture below is represented the browser screen og the rooms: Scroll a list upwards or increase the value shown on the display. Scroll a list downwards or reduce the value shown on the display. Enter the selected submenu or confirm the set value. 4.2 Display It is possible to group the Smart HP screens in three basic types: the main screens (only one if the Smart HP manages only one unit, from two to seven if zone management is used), the navigation menu, and that for modifying parameters. The lines on the display of the main screen (unit) are organized in the following manner: Fig.4.c 1- Information about the date, time and room under consideration 2- Main dimensions and their relative values (temp., humid., zone scheduler active in the room), 3- Main active actuators 4- Room status The possible states the room may be in are: • OFF, • COMFORT, • ECONOMY, • AUTO-OFF, • AUTO-COMF, • AUTO–ECON, • KEY-OFF, • BMS-OFF, • ALARM-OFF, • PROTECT. In the room status screens following icons may appear: On and steady in the zone status display screen Presents the status of the zone to heat/cool. Fig.4.b 1- Information about the date, time and units under consideration 2- Main measurements and relative values 3- Main active actuators 4- Status of the unit The units can be in the following states: • OFF, • ON, • ENERGY S., • AUTO-OFF, • AUTO-ON, • AUTO-E S., • Din-OFF, • BMS-OFF, • ALARM-OFF, • PROTECT. Presents the user the set mode COOLING (Summer). Presents the user the set mode HEATING (Winter). Indicates the humidifier is activated. Indicates the dehumidifier is activated. Indicates the three-way valve of the radiant installation is activated. Indicates the zone valve is activated. In the unit status screens following icons may appear: +030220741 Smart HP – rel. 1.0 - 05/09/2008 Note: If more than one main screen appears (that is unit and 23 zone), two arrows located in on the right of the display ( e ) allow you to scroll through the screens. The following figure shows the navigation screen for he main menus. Fig.4.d Following are the eight menus: A. On-Off/Mode , B. Setpoint, C. Time Bands, D. Inputs/Outputs, E. Alarm Log, F. Change Unit, G. Service, H. Manufacturer, The parameter modifications screens appear like the example shown below: Fig.4.e 5- Name of main menu entered 6- Screen index 7- Name of sub-menu where you are editing the parameters 8- Parameter name 9- Editable value Note: in Smart HP all editable fields are represented by numerical values or capital letters) +030220741 Smart HP – rel. 1.0 - 05/09/2008 24 5. MENU DESCRIPTION Insert password PW2 to enter into these branches Insert password PW1 to enter into these branches Main Menu - Function Tree Fig. 5.a 5.1 A. In the second selection line (editable ONLY if OFF is selected in the first line), you can select the seasonal status of the heat pump (COOLING + DOMESTIC, HEATING + DOMESTIC, ONLY DOMESTIC). The rooms that can be configured in screens A__03 and A__04, very similar to that shown in Fig. 5.b where only the first row is present. The meanings of the possible choices involve the set points of the rooms are:OFF = stand by, ECONOMY = use a reduced set point for lower energy losses, COMFORT = optimum conditions, AUTO = indicates that the scheduler is active. The remote ON-OFF digital input allows the entire system to be put in stand by, including the control of the domestic water. On-Off/Mode From the main menu (A. ) it is possible to set the status of the unit based on the choices made. Note: The Smart HP working mode (“just unit” or “unit + installation”) must be decided during construction/installation of the installation and cannot be changed by the final user using the display commands. Fig. 5.b Note: on the A__02 screen it is possible to put the installation in stand by using the “enable temporary off” function, which allows the unit to restart at a preset time (date and time). On the first selection line of the screen the following can be chosen: 1. When the Smart HP manages in the “just unit” mode: ON, OFF, ENERGY SAVING, AUTO 2. If the application must manage “unit + installation” the items for selection are: OFF and ON FROM ROOM. The items in the first case deal with the selection of only the heat pump unit and have the following meanings: ON = standard conditions, OFF = stand by, ENERGY SAVING = use of “reduced” set points for greater energy savings, AUTO = indicates that the scheduler is active. +030220741 Smart HP – rel. 1.0 - 05/09/2008 5.2 B. Setpoint From the main menu (B.) you can set the various “Set point” for only the rooms. The set points that can be set are COMFORT or ECONOMY and depend on the selection made during the unit's configuration. 25 If you want to set fewer time slots than the four pre-set, just select the symbols “--:-- “ in the “hh:mm” field of the inactive time slots and for the set point in the same manner. It is possible to set four different time slots within the same day with respective selectable set points for each time slot. Thereafter, it is possible to select all of the days of the week, by either copying the previous day, or setting each day independently. To select the set points, please refer tot he relative section and parameters in the overall parameter table. For this type of unit, the system inertia are very long on average as you are working with radiant systems that often have very large masses. In this case, the working set points (COMFORT and ECONOMY) are very similar. Consequently, also the number of time slots are also reduced because the consider the large inertia of the system. If Smart HP must manage only the unit, the “just unit” (UNIT) time slots will be displayed, whereas if it must also manage the installation, only those in the ZONE are displayed, in this case the unit is forced to operate with the most costly request. Fig. 5.c In fact, the range of room set points that can be selected by the user are constrained by the settings made during installation with the respective parameters. Note: this menu is not active if “just unit” is selected and therefore the room controls have not been activated. 5.3 C. Time bands If one zone is set to the ECONOMY mode and the other is OFF, the unit will operate with the ENERGY SAVING settings. Selectable State UNIT OFF ON ENERGY SAVING AUTO ZONE OFF COMFORT ECONOMY AUTO Description of Operation: 3 pCO is equipped with an internal clock with a buffer battery that maintains the time and date for all of the functions that require it. The time, date, time slot, closure periods, and holidays are set using the main menu for the Clock/Time Slots (C.). The related screens that appear are the following, in sequence: • • • • Note: OFF guarantees antifreeze protection of the unit in all cases. Set time and date Set the four time slots Closure period up the three max. Holidays/special dates up to twelve max. It is possible to create the time slots for one day and then copy them to the other days if you want to reuse them. 5.4 D. The screens for setting up “just unit” (unit) are: Inputs/Outputs From the main menu (D.) you can display, in sequence, both the type and the physical status of the inputs and outputs, both digital and analogue. If the inputs or outputs have not be set-up (no devices connected), “----“ will be displayed. The figures that follow show the relative screens. Fig. 5.d Note: If Clima zone or serial probe terminals are present, two sets of screens appear with the following text: “Slot Zone 1” and “Slot Zone 2”. Fig. 5.e +030220741 Smart HP – rel. 1.0 - 05/09/2008 26 Note: The values relative to the analogue outputs are expressed as percentages. 5.5 E. Alarm Log From the main menu (E. ) it is possible to display in sequence, the alarm log. To reset the alarms, access the Service menu using the password. Using the “Alarm” key, you can silence the acoustical alarm (if present), display the currently active alarms, and reset them (obviously the remain in the log). Fig. 5.h G.d. Hour counter: displays the hours worked for the main moving parts (compressors and pumps depending on the configuration) that may be subject to periodic maintenance. Fig. 5.f Note: please see the section dedicated to alarms (9.2). Note: it is possible to access the list of active alarms from the home page by pressing the 5.6 F. key. Change Unit From the main menu (F. ) you can display the set parameters in the other pCO controllers connected in the pLAN network. To to this, enter the sub-menu and enter the unit that you want to access. Once connected, the main screen will display the number of the unit in question. Fig. 5.i Note: From this point on in this sub-menu, a password must be entered to proceed (PW1 – default 1234). G.e. BMS Configuration: sets all necessary parameters for connection to a supervisor system. This depends on the type of optional board that is inserted and the type of protocol selected. By choosing “CAREL” you can connect to a supervisor via a RS485 that supports the CAREL protocol, but you can also connect to boards that convert the CAREL protocol into others, such as a TCP/IP board or a Trend board. Note: this function is not active in Smart HP release 1.0. 5.7 G. Service From the main menu (G. ) you can access the service sub-menu, which is divided into two parts. The first part (a,b,c,d) is not password protected and allows you to display the settings of the following data: G.a. Change language/unit of measure: allows you to select one of the languages loaded in the application (Italian, English). Note: changing the unit of measure from SI to British units will be available in the next release of Smart HP. G.b. Info: you can find information regarding the application code (and version) on the first available screen. The second screen contains information regarding 3 the pCO board hardware. Fig. 5.j G.a. Config./Threshold: allows you to set the threshold of the working hours for the main moving components or components subject to periodic maintenance in the unit (depending on the configuration). It is possible to reset the timers for each device on the same screen Fig. 5.g G.c. Temp. Control Unit: allows you to se t the set points for the solar panels (if present), the mixing circuit, the antifreeze function, and the heat pump unit (nominal and energy savings, in both the "heating/cooling" mode and for heating domestic water). The following images only represent the screens relative to the heat pump unit set points. Fig. 5.k G.f.b. Probe calibration: allows you to set an offset to be added or subtracted from the probe reading involved. Once an offset value (Ofs) is confirmed, press key to automatically update the value of the corresponding probe the (shown next to it). +030220741 Smart HP – rel. 1.0 - 05/09/2008 27 Fig. 5.l Fig. 5.o G.f.c. Temperature Control: in this branch, you will find all of the parameters regarding the temperature control that can be changed during installation or assistance on the installation with the exception of those that are the responsibility of the manufacturer, which are located in the H.c. branch. H.c. Manufacturer Parameters: this screen allows you to select the parameters that can be set by the manufacturer. H.d. EVD Driver: these parameters are those which allow you to set up the electronic valve driver, which in turn is divided into three sub-menus. Please see the relative documentation. G.f.d. Default/PW/Reset Al. Allows you to reset the alarm log and change password PW1. Note: for further information, please refer to the user manual dedicated to the EVD400 driver (+030220225). H.e. Default/Password: this allows you to select the default CAREL values (when you select CAREL all settings are deleted and the system returns to the default configuration indicated in the following manual). On the following screen, you can change the manufacturer's password. Fig. 5.m G.g. Manual Management: this allows you to change from the individual actuators on the unit from automatic to manual. Digital outputs allow only the states ON or OFF, whereas analogue outputs can be selected from 0 - 100%, obviously all defaults are in Auto. If selected, control is by-passed, but not the set alarm thresholds. This protects the unit's safety. Generally, this operation is selected to test the individual actuators during installation. Fig. 5.p H.f. Input/Output Test Fig. 5.n 5.8 H. Fig. 5.q Manufacturer Note: this function is not active in Smart HP release 1.0. From the main menu (H.) you can access the manufacturer's sub-menus after entering a password (PW2 – default 1234): Note: after importing the manufacturer's parameter values, you must turn off and on the pCO controller in order for the new settings to be saved and to become effective. H.a. Unit Configuration: allows you to select the basic characteristics of the unit/installation and the functionality of the individual devices. The first parameter is the type of unit and installation with circuit reversibility or not. Thereafter, a series of screens are displayed that define the salient characteristics of the individual system components (ex. type and number of compressors, etc.) of the configuration that is allowed by the hardware. H.b. I/O Configuration This menu allows you to select the functionality and presence of the individually selectable I/Os. For each individual I/O there are various possible selections, which essentially depend on the hardware used and by the fact that some I/Os can take on different functions than those set up in the default configuration. For the digital I/Os, you can select the status of the device, that is NO or NC logic. For the Analogue outputs, the min. and max. output values can be selected (default 0 - 100 %). Furthermore, it is possible to select the type of input for the analogue inputs (ex. 0 - 10 V, 4 - 20 mA, etc.) as well as the working range of the connected probe (ex. for the high pressure probe: 0 - 44.8 Bar). Following is an example of the selection of the digital inputs: +030220741 Smart HP – rel. 1.0 - 05/09/2008 28 6. FUNCTIONS 6.1 Compressor Management Note: also in the units Type 1,2,3,4, it is possible to select the EVD400 driver. In the units 3 and 4 the high and low pressure thresholds refer to the probes connected to the pCO³ board while EVD400 keeps working with the related probes. Often these units only use scroll type hermetic compressors. Smart HP can manage up to two compressors on a refrigeration circuit. These are used to produce the installation and the domestic water circuit water, both hot and cold, based on the active seasonal mode. If there are two compressors in the installation, they can be turned on in an alternating manner in a FIFO (First In First Out) rotation that can be set on the Hc_10 screen. Management times are CAREL standard, that means minimum time on, off between two turn-on's of the same compressor and between different compressors. The same is true for the delays in turning on the unit and the respective installation pumps. These parameters can be displayed in the Manufacturer (H) branch Æ Manufacturer Params. ( c ). Please refer to the following figure for their meanings: 6.3 Antifreeze Function This function allows you to avoid the possibility of reaching temperatures that are potentially dangerous to the installation and geothermal probes. Readings are performed using the relative outlet temperature probes (on the geothermal circuit and primary installation) and by setting a set point and a antifreeze differential for the individual water circuits. These values can be set in the Service branch (Gfc35… Gfc38). This is a severe alarm that blocks the heat pump. Reset may be either manual or automatic, based on the selection made in the previously listed screens (see the table of alarms). The operational diagram is provided in the following figure: Fig. 6.b An antifreeze protection set point can be ser for the rooms that reactivates the unit from Stand-by if one of the serial probes/Climas fall below this value. This set point can be set in the Service branch (Gfc46) while its differential is set to 3°C. The same it true for its reset, whish is automatic. Fig. 6.a 6.4 Control of the installation Water and the Geothermal Circuit 3 The pCO controller manages the compressor alarms and more specifically, the thermal overload switch for each (without delays and with manual reset), the high pressure switch without delays and with manual reset; and/or the high pressure probe, using a threshold (Hc_01) which allows the operation of one compressor to be stopped (if two are present). The low pressure alarm may come from either a pressure switch or probe. This alarm has a settable delay and can be reset manually or automatically (in the latter case, five attempts are made before switching to the manual mode). These parameters are found in the Hc_02 - Hc_05 screens. The circuit may be equipped with an electronic expansion valve controlled by an EVD400 driver. In this case, the low and high pressure probes are those connected to the electronic expansion valves and therefore the ones on the 3 pCO board are not connected. Basic control managed by Smart HP is performed based on the outlet temperature of the mixing circuit, and acts on the three-way modulating valve. The cooling and heating control set point is set in the Service branch parameters (Gc_02); whereas the DYNAMIC and FIXED POINT control, the control band, the type of control (P = proportional, P+I = proportional + integral), the integration time constant, any possible heating temperature compensation, the offset to avoid condensation when cooling, and the temperature limits can be set using the screens Gfc30 - Gfc34. 6.2 EVD400 Electronic Valve Management To optimize the refrigeration circuit operation, an electronic expansion valve (E2V-E3V, etc.) with its relative EVD400 driver can be used, which is inserted in the pLAN network with an address of No. 5. Using the EVD400, the high and low pressure probes of the compressors are 3 connected to it and their measurements are transmitted to the pCO controller across the serial pLAN network. Their parameters are set in the special settings branch for the Manufacturer (H.) Æ EVD Driver (d) that in turn is divided into three sub-menus (a.EVD Parameters, b,Autosetup, c.Advanced Parameters). The probe readings and status of the E*V valves are found under the Inputs/Outputs branch (D.). For tests and checks during installation start-up, you will find the screens for manual forcing of the electronic expansion valve under the Service (G.), Manual Management (g) branch. For further information regarding the individual parameters, please refer to the manual dedicated to the EVD400 ( +030220225, Italian and +030220227, English). +030220741 Smart HP – rel. 1.0 - 05/09/2008 Fig. 6.c Control of the compressor(s) operation is such that it ensures the return temperature of the primary circuit for both cooling and heating operation, which are set up on screens Gc_04 and Gc_05. The following figures illustrate the heating thermostat control of the compressors when either 1 or 2 compressors are present. Cooling is obviously mirrored (direct) and refers to the relative working set points (Chiller). 29 Fig. 6.d Fig. 6.f In the primary circuit of the heating function mode, heaters in the heatexchanger or a furnace (which receive a remote on/off and operates with its own set point settings) can be used to integrate the system (digital output NO6 3 on the pCO board. In the cooling mode, the outlet probe of the primary circuit guarantees antifreeze protection (please see the section dedicated to the Antifreeze Function) for the unit's heat-exchanger. All of these parameters can be set under Service (G) Æ Service Parameters (f) Æ Temperature Control (c ). For dehumidification, in addition to the activation of the specific actuator, it is possible to set a safety offset (selectable on Gfc31) for the outlet temperature of the installation in order to avoid reading the dew point of the rooms. This offset raises the installation operating temperature using the modulating valve in the mixing circuit (conditioning it to the highest dew point temperature measured in the individual rooms). For humidification and dehumidification, there is a single alarm input (except for the unit type 6, which has two separate alarms) which indicates faults in the system active at that time. For reversible units (heating and air conditioning) an inverting valve is used in the refrigeration circuit. In this manner, the flows are also inverted in the heat exchangers (installation and geothermal). Furthermore, four-way valves installed in the water circuits can also be controlled with the same output. This allows the counter flows to be maintained on the heat exchangers. In this configuration, the probes must be installed downstream of the four-way water valves in order to avoid inversion of the reading. 6.6 Domestic Water Temperature Control and Anti-Legionnaire Function This application allows the domestic water temperature to be controlled by activating a 3-way switching valve (see Unit Type 1) and a pump on the relative desuperheater, which can also act as a total recovery unit if the unit is reversible. Control is performed using probe B3 and the relative set points (Nominal and Energy Savings) are set using screens Gc_04 and Gc_05. The working differential is set by the manufacturer in screen Hc_06, which in installations with 2 compressors is equally divided between the two. Continuous or thermostat operation of the domestic water pump is set using the Manufacturer Hc_23 branch. If the modulating output is used for the domestic water pump, it will be active at 100 % if working below the set point. It will work at 35 % (fixed) if the water temperature is above the set point, regardless of the choice made on screen Hc_23. Normally, these units are equipped with an accumulator tank that allows the water to stratify. Furthermore, it includes integrating systems that can be either electric heaters or a furnace, in addition to solar panels (as explained in the following section). The operational diagram is as follows: For the geothermal circuit, the control pump can be either an on-off type or modulating. In the latter case if operation is proportional with working set points and relative differentials, these are set in on screen Gfc50. and the minimum value is set to 35 % of the output. For antifreeze protection, please see the specific section. The following diagram illustrates the operation of the modulating pump: Fig. 6.e 6.5 Humidify and Dehumidify Management Fig. 6.g The management of the room humidity control is performed by the primary air treatment system and performed using the readings of the serial probes or Clima present in the rooms. The humidification system (controlled by a proportional output, Y4) is active under heating; whereas the dehumidification system (controlled by an on-off output, NO11) is active under cooling. For its operation, the dew point of the individual rooms controlled are considered. The presence of these systems is set using screen Gfc39. The humidification and dehumidification control set points act based on a mathematical average of the readings from the probes/Clima present in the installation and can be set by the end user directly in the Set Point menu (B). The humidification and dehumidification differentials are set using the screen Gfc40. The settable limits of the set points by the final user can be set during installation on the screen Gfc44. The diagrams below illustrate their relative operation: Integral Domestic Water Heaters: In this case, the relative digital output (NO7 set using the parameter located on the screen Gfc25) is activated in deactivated as a function of the differential values (Gfc28) compared to the working set point, as shown in the following diagram: Fig. 6.h Integral Domestic Water Furnace: In this case, the relative digital output (NO7 set using the parameter located on screen Gfc25, which allows setting this in place of the heat pump) is activated and deactivated as a function of a set point and a differential set on screen Gfc27. +030220741 Smart HP – rel. 1.0 - 05/09/2008 30 Anti-Legionnaire Function: It is possible to activate a weekly algorithm (from screen Gc_03) that using a domestic water integration output, allows avoiding problems related to the proliferation of Legionnaire's Disease, by raising the set point to a value that can be set for a fixed time of 1 hour. 6.9 Management of the zones using the Serial probes or Clima It is possible to connect rooms to the zone terminal system (Clima) or DPW**14000 model serial probes. Up to six units can be configured using the Service menu (Gfc branch). Both the probes and the Clima terminals communicate the relative temperatures and humilities (based on the models 3 connected) to the pCO board for room control. In both cases, there are one or two settable scheduler(s)/zone(s) (Gfc branch). Using the main menu, you can choose the operating mode (A. On-off/Mode), Set points (B.) and the relative Time Slots (C.). For further information, please see section 5. If serial probes are used, the outputs for the two zones/schedulers are available 3 on the pCO board (NO12 and NO13). If Clima is used, the two outputs on the same terminal can be used, and consequently there are six available zone pumps for connection (in any case paired with the two schedulers/zones). For temperature control: • If the serial probes are connected, the scheduler/zone working set point uses the average temperature of the activated probes for the respective zone/scheduler. • For the Clima terminal, the Clima control is used, on which the 3 pCO controller transmits the working set point for the relative zone. In any case, from the individual terminal, it is possible to temporarily modify the local set point using the on-off switch in order to activate the next time slot or to turn it off. In this case, it is reactivated with the same key. If all Clima terminals are turned off, the installation goes into stand-by until it is manually reactivated using at least one terminal. If the installation also performs cooling, serial probes or Clima with incorporated humidity reading must be used to correctly manage the installation (please see the relative section) and the conditioned mixing valve for temperature control (that is increased by a settable off-set, on Gfc31) of the dew point temperature in the individual rooms, in order to avoid surface condensate phenomena. 3 The pCO uses the mathematical average of all serial probes or active Clima to control the humidifier and dehumidifier (please refer to the section regarding humidify/dehumidify). Humidity control is only active on heating; dehumidification is active only on cooling operation. 3 Both the serial probes and Clima transmit the alarms to the pCO board, which are displayed on the system terminal (pGD1) and also, if connected, on a supervisor (BMS). 6.7 Solar Panel Management From the Service menu (Gfc23) you can select the presence of one or two solar panels (the two panels are used for east-west orientation of the panels). 3 The probes located on the panels (B9 and B10 on the pCO board) must be PT1000s, which guarantee a maximum operating temperature of up to 200°C. For each individual panel, to control the pump functions based on the temperature difference between the panel probe and the low portion of the domestic water tank. The relative set point and control ban can be set in the unit's temperature control parameters (screen Gc_01). Fig. 6.i Key T panel T low B9 and/or B10 Temperature of the lower portion of the domestic water tank If there are two panels (one oriented eastwards and the other westwards) the set point and working differential are the same for both. The entire operation (of the pumps) is independent and the minimum time of activation is set to 30s. On screen Gfc23 you can also set a warning threshold for the load of the domestic water load. Above this threshold, the solar panel pumps are deactivated, and they will restart operation only if they exceed the max. temperature, again settable on the same screen, and will be definitively stopped once they reach the maximum load threshold of the tank (see the diagram in the section regarding domestic water control). It is also possible to configure a circuit with a heat exchanger between the solar panel and the tank, by having the two pumps operate in parallel. 6.10 Recovery Fans If a primary air system is present for the rooms, it can be activated and deactivated directly by Smart HP using the relative digital outputs. This function can be set up in the Service branch, on screen Gfc47. This output is activated by “system on” and is independent of the zone and heat pump status (it remains active even if only Domestic is active). It is deactivated when the system is turned OFF, from the digital input, and/or form the keypad. 3 Note: this option is only available if Smart HP is installed on a pCO Large control board. 6.8 Temperature Compensation Under heating operation, the mixing circuit outlet set point (Gc_02) may be positively compensated based on the outside temperature. This function is activated by selecting Dynamic operation on the Gfc30 screen and by setting an activation set point based on the outside temperature with a relative slope given in percentage (ex. if you select 50 % and a reduction of 1 °C of the outside temperature you obtain an increase of 0.5 °C in the outlet set point). The maximum limit of the mixing circuit outlet set is set on screen Gfc34. The diagram below illustrates the its following operation: Fig. 6.j +030220741 Smart HP – rel. 1.0 - 05/09/2008 31 7. PARAMETER TABLE Insert password PW2 to enter into these branches Insert password PW1 to enter into these branches Function Tree “Mask index”: shows univocally the address of each mask and therefore the parameters editable in this mask; e.g., with reference to the “functions tree” abovementioned). To reach the Mask index parameter , make the following steps: Main menu Æ Æ and browse all the masks up to the fifth ( (after having inserted the relevant password PW1) Æ ). Following is the table of parameters that can displayed on the terminal. Mask Index A__01 Descr. display Def UOM Min Max On/Off with terminals in room 0 --- 0 1 On/Off with only heat pump 0 --- 0 3 Select cooling/heating for reversible units 0 --- 0 2 Select cooling/heating for only heating units 0 --- 0 1 Heat pump unit Enable sleep mode: A__02 Start function: A__03 Descr. On-Off Zone 01 : Enable "Restart on" 0 --- 0 1 Day to restart for "Restart on" function Month to restart for "Restart on" function Year to restart for "Restart on" function Time to restart for "Restart on" function --------- ------h 1 1 0 0 31 12 99 23 Start of the "Restart on" function 0 --- 0 1 On-Off for Scheduler/Zone 01 0 --- 0 3 +030220741 Smart HP – rel. 1.0 - 05/09/2008 32 Value description 0: OFF 1: ON from room 0: OFF 1: ON 2: ENERGY SAVE 3: AUTO 0: DHW ONLY 1: HEATING + DHW 2: COOLING + DHW 0: DHW ONLY 1: HEATING + DHW 0: NO 1: YES 0: NO 1: YES 0: OFF Type R/W BMS addr. I R/W I R/W 5 I R/W 6 I R/W D R/W I I I I R/W R/W R/W R/W D R/W I R/W Mask Index A__04 B__01 B__02 Descr. display On-Off Zone 02 : Comfort Temp. Cooling Comfort Temp. Heating Comfort Umid. Cooling Comfort Umid. Heating Economy Temp. Cooling Economy Temp. Heating Economy Umid. Cooling Economy Umid. Heating Clock Time: Descr. Def On-Off for Scheduler/Zone 02 Comfort ambient temp. set point (cooling) Comfort ambient temp. set point (heating) Comfort ambient humidity set point (cooling) Comfort ambient humidity set point (heating) Economy ambient temp. set point (cooling) Economy ambient temp. set point (heating) Economy ambient humidity set point (cooling) Economy ambient humidity set point (heating) Set hour Set minutes Set day Set month Set year UOM Min Max Day --- Day to copy from scheduler 25.0 20.0 50.0 50.0 26.0 19.0 50.0 50.0 °C °C %rH %rH °C °C %rH %rH Gfc43 Gfc43 Gfc44 Gfc44 Gfc43 Gfc43 Gfc44 Gfc44 Gfc43 Gfc43 Gfc44 Gfc44 Gfc43 Gfc43 Gfc44 Gfc44 A A A A A A A A R/W R/W R/W R/W R/W R/W R/W R/W 13 14 24 23 15 16 22 21 ----------- h --------- 0 0 1 1 0 23 59 31 12 99 I I I I I R/W R/W R/W R/W R/W 15 16 14 17 18 I R 11 I R/W D R/W I I R/W R/W I R/W I I R/W R/W I R/W I I R/W R/W I R/W I I R/W R/W I R/W D R/W I I R/W R/W I R/W I I I I R/W R/W R/W R/W I R/W I I I I R/W R/W R/W R/W I R/W I R/W Day of the week calculated based on the current date --- --- 1 7 Set day Unit time slots 0 --- 0 6 Allows copying the time slots of individual days --- --- 0 1 Set start hour time slot 1 Set start minute time slot 1 8 30 ----- 0 0 23 59 Set set point type time slot 1 1 --- 0 2 Set start hour time slot 2 Set start minute time slot 2 12 30 ----- 0 0 23 59 Set set point type time slot 2 2 --- 0 2 Set start hour time slot 3 Set start minute time slot 3 13 30 ----- 0 0 23 59 Set set point type time slot 3 1 --- 0 2 Set start hour time slot 4 Set start minute time slot 4 17 30 ----- 0 0 23 59 Set set point type time slot 4 0 --- 0 2 F4 Enable unit holidays 0 --- 0 1 Set start day holiday 1 Set start month holiday 1 ----- ----- 0 0 31 12 Set set point type holiday 1 0 --- 0 2 Set end day holiday 1 Set end month holiday 1 Set start day holiday 2 Set start month holiday 2 --------- --------- 0 0 0 0 31 12 31 12 Set set point type holiday 2 0 --- 0 2 Set end day holiday 2 Set end month holiday 2 Set start day holiday 3 Set start month holiday 3 --------- --------- 0 0 0 0 31 12 31 12 Set set point type holiday 3 0 --- 0 2 Set end day holiday 3 --- --- 0 31 Start1 Stop1 Start2 Stop2 Start3 Stop3 +030220741 Smart HP – rel. 1.0 - 05/09/2008 R/W 3 F3 Enable holidays I BMS addr. 0 F2 C__03 R/W --- F1 C__02 1: COMFORT 2: ECONOMY 3: AUTO 0: OFF 1: COMFORT 2: ECONOMY 3: AUTO Type 0 C__01 Day: Value description 33 1: Monday 2: Tuesday 3: Wednesday 4: Thursday 5: Friday 6: Saturday 7: Sunday 0: MONDAY 1: TUESDAY 2: WEDNESDAY 3: THURSDAY 4: FRIDAY 5: SATURDAY 6: SUNDAY 0: No 1: Yes 0 - 23 0 - 59 0: OFF 1: ON 2: ENERGY SAVE 0 - 23 0 - 59 0: OFF 1: ON 2: ENERGY SAVE 0 - 23 0 - 59 0: OFF 1: ON 2: ENERGY SAVE 0 - 23 0 - 59 0: OFF 1: ON 2: ENERGY SAVE 0: NO 1: YES 0 – 31 0 - 12 0: OFF 1: ON 2: ENERGY SAVE 0 – 31 0 - 12 0 – 31 0 - 12 0: OFF 1: ON 2: ENERGY SAVE 0 – 31 0 - 12 0 – 31 0 - 12 0: OFF 1: ON 2: ENERGY SAVE 0 – 31 Mask Index Descr. display Enable special days C__04 Descr. Def UOM Min Max Set end month holiday 3 --- --- 0 12 Enable unit yearly special days 0 --- 0 1 Set special day 1…6 Set special day month 1…6 ----- ----- 0 0 31 12 Set set point type special day 1…6 0 --- 0 2 Set day Time slots Zone 01 0 --- 0 6 SD1…SD6 Zone 01 bands Day: Zone 01 bands Copy in: Allows copying the time slots of individual days 0 --- 0 1 Set start hour time slot 1 Set start minute time slot 1 8 30 ----- 0 0 23 59 Set set point type time slot 1 1 --- 0 2 Set start hour time slot 2 Set start minute time slot 2 12 30 ----- 0 0 23 59 Set set point type time slot 2 2 --- 0 2 Set start hour time slot 3 Set start minute time slot 3 13 30 ----- 0 0 23 59 Set set point type time slot 3 1 --- 0 2 Set start hour time slot 4 Set start minute time slot 4 17 30 ----- 0 0 23 59 Set set point type time slot 4 0 --- 0 2 F1 C__05 F2 F3 F4 Enable holidays Enable unit holidays zone 01 0 --- 0 1 Set start day holiday 1 Set start month holiday 1 ----- ----- 0 0 31 12 Set set point type holiday 1 0 --- 0 2 Set end day holiday 1 Set end month holiday 1 Set start day holiday 2 Set start month holiday 2 --------- --------- 0 0 0 0 31 12 31 12 Set set point type holiday 2 0 --- 0 2 Set end day holiday 2 Set end month holiday 2 Set start day holiday 3 Set start month holiday 3 --------- --------- 0 0 0 0 31 12 31 12 Set set point type holiday 3 0 --- 0 2 Set end day holiday 3 Set end month holiday 3 ----- ----- 0 0 31 12 Start1 Stop1 C__06 Start2 Stop2 Start3 Stop3 Enable special days C__07 Enable unit yearly special days zone 01 0 --- 0 1 Set special day 1…6 Set special day month 1…6 ----- ----- 0 0 31 12 Set set point type special day 1…6 0 --- 0 2 Set day Time slots Zone 02 0 --- 0 6 SD1…SD6 C__08 Zone 02 bands Day: Zone 02 bands Copy in: Allows copying the time slots of individual days 0 --- 0 1 Set start hour time slot 1 Set start minute time slot 1 8 30 ----- 0 0 23 59 Set set point type time slot 1 1 --- 0 2 Set start hour time slot 2 Set start minute time slot 2 12 30 ----- 0 0 23 59 F1 F2 +030220741 Smart HP – rel. 1.0 - 05/09/2008 34 Value description 0 - 12 0: NO 1: YES 0 – 31 0 - 12 0: OFF 1: ON 2: ENERGY SAVE 0: MONDAY 1: TUESDAY 2: WEDNESDAY 3: TUESDAY 4: FRIDAY 5: SATURDAY 6: SUNDAY 0: No 1: Yes 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0: NO 1: YES 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0 – 31 0 - 12 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0 – 31 0 - 12 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0 – 31 0 - 12 0: NO 1: YES 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0: MONDAY 1: TUESDAY 2: WEDNESDAY 3: TUESDAY 4: FRIDAY 5: SATURDAY 6: SUNDAY 0: No 1: Yes 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0 - 23 0 - 59 Type R/W I R/W D R/W I I R/W R/W I R/W I R/W D R/W I I R/W R/W I R/W I I R/W R/W I R/W I I R/W R/W I R/W I I R/W R/W I R/W D R/W I I R/W R/W I R/W I I I I R/W R/W R/W R/W I R/W I I I I R/W R/W R/W R/W I R/W I I R/W R/W D R/W I I R/W R/W I R/W I R/W D R/W I I R/W R/W I R/W I I R/W R/W BMS addr. Mask Index Descr. display Descr. Def UOM Min Max Set set point type time slot 2 2 --- 0 2 Set start hour time slot 3 Set start minute time slot 3 13 30 ----- 0 0 23 59 Set set point type time slot 3 1 --- 0 2 Set start hour time slot 4 Set start minute time slot 4 17 30 ----- 0 0 23 59 Set set point type time slot 4 0 --- 0 2 F3 F4 Enable holidays Enable unit holidays zone 02 0 --- 0 1 Set start day holiday 1 Set start month holiday 1 ----- ----- 0 0 31 12 Set set point type holiday 1 0 --- 0 2 Set end day holiday 1 Set end month holiday 1 Set start day holiday 2 Set start month holiday 2 --------- --------- 0 0 0 0 31 12 31 12 Set set point type holiday 2 0 --- 0 2 Set end day holiday 2 Set end month holiday 2 Set start day holiday 3 Set start month holiday 3 --------- --------- 0 0 0 0 31 12 31 12 Set set point type holiday 3 0 --- 0 2 Set end day holiday 3 Set end month holiday 3 ----- ----- 0 0 31 12 Start1 Stop1 C__09 Start2 Stop2 Start3 Stop3 Enable special days C__10 I I R/W R/W I R/W I I R/W R/W I R/W D R/W I I R/W R/W I R/W I I I I R/W R/W R/W R/W I R/W I I I I R/W R/W R/W R/W I R/W I I R/W R/W D R/W I I R/W R/W I R/W --- 0 1 ----- 0 0 31 12 Set set point type special day 1…6 0 --- 0 2 ----------------- °C °C °C °C °C °C °C °C -99.9 -99.9 -99.9 -99.9 -99.9 -100 -99.9 -99.9 99.9 99.9 99.9 99.9 99.9 200 99.9 99.9 A A A A A A A A R R R R R R R R 5 35 --- °C -99.9 99.9 A R 12 --- °C -01.0 99.9 A R 7 --- °C -01.0 99.9 A R 6 --- °C -99.9 99.9 A R 12 --- °C -99.9 99.9 A R 4 --- °C -99.9 99.9 A R 9 --- °C -100 200 A R 10 --- °C -100 200 A R 11 D R D R D R D R D R D R D R ID01= Geothermal Field Side Flow Switch --- --- 0 1 02= Overl. comp. 1: ID02= Compressor 1 Thermal Overload Switch --- --- 0 1 03= High press. sw. : ID03= Compressor 1 High Pressure Switch --- --- 0 1 ID04= Compressor 1 Low Pressure Switch --- --- 0 1 --- --- 0 1 --- --- 0 1 --- --- 0 1 D__10 07= Add heat. alarm: R/W 0 01= Geo. flow sw. : 06= Overl. DHW heat.: I BMS addr. ----- B1= Geothermal Outlet Water Temperature B2= Geothermal Inlet Water Temperature D__02 B3= Domestic Hot Water Temperature B4= Mixing Circuit Outlet Water Temperature D__03 B5= Primary Circuit Inlet Water Temperature B4= Compressor Exhaust Gas Temperature D__04 B5= Primary Circuit Inlet Water Temperature D__05 B6= Outside Air Temperature B6= Primary Installation Circuit Water Outlet Temperature D__06 B6 = System outlet temperature: (for unit type 4) B7= High Pressure Transducer B7 =Condensation: (on unit type 3 or 4) D__07 B8= Low Pressure Transducer B8 =Evaporation : (on unit type 3 or 4) B7= Primary Installation Circuit Water Outlet Temperature B7 = System outlet temperature: (for unit type 5 or 6) B8= Mixing Circuit Outlet Water Temperature (for unit D__08 B8 = Mix circ. outlet: type 5) B8= Solar Circuit Boiler Inlet Temperature (for unit type B8 = Solar circuit return: 6) B9 = Solar colletor 1 B9= Solar Panel 1 Temperature temperature: D__09 B10= Solar colletor 2 B10= Solar Panel 2 Temperature temperature: D__11 05= Overload Pumps : 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0 - 23 0 - 59 0: OFF 1: COMFORT 2: ECONOMY 0: NO 1: YES 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0 – 31 0 - 12 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0 – 31 0 - 12 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY 0 – 31 0 - 12 0: NO 1: YES 0 – 31 0 - 12 0: OFF 1: COMFORT 2: ECONOMY R/W Enable Zone 02 yearly special days B1 = Geothermal outlet temp.: B2 = Geothermal inlet temp: B3 = DHW control temperature: B4 = Mix outlet temperature: B5 = Sys. return temperature: B4 = Discharge comp. 1: B5 = Sys. return temperature: B6 = Outside temperature: 04= Olw press. sw. : 0: OFF 1: COMFORT 2: ECONOMY Type Set special day 1…6 Set special day month 1…6 SD1…SD6 D__01 Value description ID05= Unit/Installation Pump Thermal Overload Switch (on unit type 1 or 2) ID06= Domestic Hot Water Storage Heater Thermal Overload Switch (on unit type 1 or 2) ID07= Installation Integrated Furnace/Heater Thermal +030220741 Smart HP – rel. 1.0 - 05/09/2008 35 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1 2 3 4 5 Mask Index Descr. display Descr. Def UOM Min Max --- --- 0 1 --- --- 0 1 --- --- 0 1 --- --- 0 1 Overload Switch 08= Remote On/Off : 05= Overl. geo. Pump: 06= Overl. sys. Pump: D__12 07= Add heat. alarm: ID08= Remote On-Off ID05= Geothermal Pump Thermal Overload Switch (on unit type 3, 4, 5 or 6) ID06= Primary Circuit Pump Thermal Overload Switch (on unit type 3, 4, 5 or 6) ID07= Installation Integrated Furnace/Heater Thermal Overload Switch 08= Remote On/Off : ID08= Remote On-Off --- --- 0 1 09= Overload comp. 2: ID09= Compressor 2 Thermal Overload Switch --- --- 0 1 10= H.Press. comp. 2: ID10= Compressor 2 High Pressure Switch --- --- 0 1 11= Overl. DHW pump: ID11= Domestic Pump Thermal Overload Switch --- --- 0 1 12= Overl. mix pump: ID12= Mixing Circuit Pump Thermal Overload Switch (on unit type 3) --- --- 0 1 09= Overload comp. 2: ID09= Compressor 2 Thermal Overload Switch --- --- 0 1 10= H.Press. comp. 2: ID10= Compressor 2 High Pressure Switch --- --- 0 1 11= Overl. DHW pump: ID11= Domestic Pump Thermal Overload Switch --- --- 0 1 12= Sys. Flow switch: ID12= Installation Circuit Flow Switch (on unit type 4, 5 or 6) --- --- 0 1 13= Humidifier al. : ID13= Humidifier Alarm --- --- 0 1 14= Overl. DHW heat.: ID14= ACS Storage Heater Thermal Overload Switch --- --- 0 1 15= Overl. mix pump: ID15= Mixing Circuit Pump Thermal Overload Switch --- --- 0 1 16= Deumidif. al. : ID16= Dehumidifier Alarm --- --- 0 1 17= Overload Solar 1 : ID17= Solar Circuit Pump 1 Thermal Overload Switch --- --- 0 1 18= Overload Solar 2 : ID18= Solar Circuit Pump 2 Thermal Overload Switch --- --- 0 1 01= Compressor 1 : NO1= Compressor 1 --- --- 0 1 02= Geotherm. pump : NO2= Geothermal Pump --- --- 0 1 03= System pump : NO3= Installation Pump --- --- 0 1 04= DHW 3way valve : NO4= Domestic Water Circuit 3-way Valve (on unit type 1) --- --- 0 1 01= Compressor 1 : NO1= Compressor 1 --- --- 0 1 02= Geotherm. pump : NO2= Geothermal Pump --- --- 0 1 03= Primary pump : NO3= Installation Pump --- --- 0 1 04= DHW pump: NO4= Domestic Pump --- --- 0 1 05= Mixing pump : NO5= Mixing Pump --- --- 0 1 06= Boiler/Heater : NO6= Furnace/Heater --- --- 0 1 07= DHW heaters : NO7= ACS Heater --- --- 0 1 08= Alarm/Fan : NO8= Alarm/Recovery Fan --- --- 0 1 09= Compressor 2 : NO9= Compressor 2 --- --- 0 1 10= 4-way valve : NO10= 4-way Valve --- --- 0 1 D__20 11= Dehumidifier : NO11= Dehumidifier --- --- 0 1 12= Valve Zone 1 : NO12= Zone 1 Valve --- --- 0 1 13= Valve Zone 2 : NO13= Zone 2 Valve --- --- 0 1 D__13 D__14 D__15 D__16 D__17 D__18 D__19 NO14= Recovery Fan --- --- 0 1 D__21 15= Solar pump 1: 14= Recov. fan : NO15= Solar Pump 1 --- --- 0 1 16= Solar pump 2 : NO15= Solar Pump 2 --- --- 0 1 Y1= ACS Modulating Pump Y2= Geothermal Modulating Pump Y3= Mixing Circuit 3-way Valve Y4= Modulating Humidifier Temperature, Humidity of Serial Probe No. 01 ----------------- % % % % °C % °C °C 0 0 0 0 -99.9 0 -99.9 -99.9 100 100 100 100 99.9 99.9 99.9 99.9 01= DHW mod. pump : 02= Geotherm. Pump : D__22 03= 3way mix valve : 04= Humidifier : Temperature : D__23 Humidity : Dew Point : D__24 Temperature : Temperature, Humidity of +030220741 Smart HP – rel. 1.0 - 05/09/2008 36 Value description 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON 0: OFF 1: ON Type R/W D R D R D R D R D R D R D R D R D R D R D R D R D R D R D R D R D R D R BMS addr. D R D R 11 D R 12 D R 13 D R 14 D R 11 D R 12 D R 13 D R 14 D R 15 D R 16 D R 17 D R 18 D R 19 D R 20 D R 21 D R 22 D R 23 D R 24 D R 25 D R 26 I I I I A A A A R R R R R R R R 3 4 2 1 50 51 52 Mask Index D__25 D__26 D__27 D__28 D__29 D__30 D__31 D__32 D__33 D__34 Descr. display Humidity : Dew Point : Temperature : Humidity : Dew Point : Temperature : Humidity : Dew Point : Temperature : Humidity : Dew Point : Temperature : Humidity : Dew Point : Temperature : Humidity : Dew Point : Relay 1: Serial Probe No. 02 Temperature, Humidity of Serial Probe No. 03 Temperature, Humidity of Serial Probe No. 04 Temperature, Humidity of Serial Probe No. 05 Temperature, Humidity of Serial Probe No. 06 Temperature, humidity, output status of Clima No. 1 Def UOM Min Max ----------------------------------- % °C °C % °C °C % °C °C % °C °C % °C °C % °C 0 -99.9 -99.9 0 -99.9 -99.9 0 -99.9 -99.9 0 -99.9 -99.9 0 -99.9 -99.9 0 -99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 --- --- 0 1 Relay 2: --- --- 0 1 Analog output: Temperature : Humidity : Dew Point : --------- % °C % °C 0 -99.9 0 -99.9 100 99.9 99.9 99.9 --- --- 0 1 Relay 1: Temperature, humidity, output status of Clima No. 2 Relay 2: --- --- 0 1 Analog output: Temperature : Humidity : Dew Point : --------- % °C % °C 0 -99.9 0 -99.9 100 99.9 99.9 99.9 --- --- 0 1 Relay 1: Temperature, humidity, output status of Clima No. 3 Relay 2: --- --- 0 1 Analog output: Temperature : Humidity : Dew Point : --------- % °C % °C 0 -99.9 0 -99.9 100 99.9 99.9 99.9 --- --- 0 1 Relay 1: Temperature, humidity, output status of Clima No. 4 Relay 2: --- --- 0 1 Analog output: Temperature : Humidity : Dew Point : --------- % °C % °C 0 -99.9 0 -99.9 100 99.9 99.9 99.9 --- --- 0 1 Relay 1: Temperature, humidity, output status of Clima No. 5 Relay 2: --- --- 0 1 Analog output: Temperature : Humidity : Dew Point : --------- % °C % °C 0 -99.9 0 -99.9 100 99.9 99.9 99.9 --- --- 0 1 Relay 1: Temperature, humidity, output status of Clima No. 6 Relay 2: --- --- 0 1 Analog output: --- % 0 100 Mode D__35 Descr. EEV EEV position Power request Operating status of EVD400 driver --- --- 0 2 Operating modes of EVD400 driver --- --- 0 1 No. Steps By Valve Percentage Power Required ----- --% 0 0 9999 100 Type of Refrigerant Used --- --- 0 13 Superheat Temperature Superheat Set Point Evaporation Temperature Suction Temperature --------- °C °C °C °C -999.9 -99.9 -999.9 -999.9 999.9 99.9 999.9 999.9 D__36 SuperHeat Actual SH Set Satured Temp Suction Temp +030220741 Smart HP – rel. 1.0 - 05/09/2008 37 Value description 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Open 1: Closed 0: Cool 1: Heat 2: Defrost 0: AUTO 1: MAN. 0: --1: R22 2: R134a 3: R404a 4: R407c 5: R410a 6: R507c 7: R290 8: R600 9: R600a 10: R717 11: R744 12: R728 13: R1270 Type R/W BMS addr. A A A A A A A A A A A A A A A A A R R R R R R R R R R R R R R R R R 53 D R D R A A A A R R R R D R D R A A A A R R R R D R D R A A A A R R R R D R D R A A A A R R R R D R D R A A A A R R R R D R D R A R I R D R I I R R I R I I I I R R R R 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 Mask Index Descr. display Def UOM Min Max Evaporation Pressure Evaporation Temperature ----- barg °C -99.9 -99.9 Condensing Pressure --- barg View Status of Low Superheating --- View Status of High Condensing Temperature LOP MOP Evap.pressure Evap.temp. Descr. Value description Type R/W 99.9 99.9 I I R R -99.9 99.9 I R --- 0 1 D R --- --- 0 1 D R View Status of LOP --- --- 0 1 D R View Status of MOP --- --- 0 1 D R EVD400 Driver Hardware Version EVD400 Driver Software Version Temperature, Humidity of Outside Serial Probe ------- ----°C 0 0 -99.9 999 999 99.9 I I A R R R --- % 0 99.9 A R Progressive Alarm Number 0 --- 0 50 I R I R A A A A R R R R I R/W BMS addr. D__37 Aux.probe Low Superheat Hight t.cond D__38 D__39 EVD version HW SW Driver Temperature: D__40 Humidity: Alarm log E__ Alarm Code followed by Time, Date and Description of Event 0 --- 0 24 Primary Installation Inlet/Outlet Temp. Geothermal Probe Inlet/Outlet Temp. Domestic Water Control Temp. High and Low Pressure Refrigeration Circuit --------- °C °C °C bar -99.9 -99.9 -99.9 -1.0 99.9 99.9 99.9 99.9 Change language from Italian to English --- --- 0 1 0 1 E__ Inlet Outlet Plant : Geoth : DHW : Press :Hp Lp Ga_01 Ga_02 Gb_01 Gb_02 Gc_01 Gc_02 Language Disable language screen when Deactivate the language change screen when turn on start: Countdown: Display time of language change screen on start-up Information on application code, BIOS and BOOT version Code:FLSTDmHPGE with issue date Type of pCO3 (small, medium, large) installed with Information Type of pCO: relative Flash Memory and RAM Temperature control water solar Solar Panel Recovery Temperature Set Point temperature : Solar Panel Recovery Temperature Differential Mixing Circuit Water Outlet Set Point in Cooling Circ. outlet set point mixed cooling: Mixing Circuit Water Outlet Set Point in Heating Antilegionella cyc:: Set Point: Gc_04 Start cycle Time: Nominal Setpoints (ON) Chiller : HP : DHW : Antifreeze Cycle Start Day Antifreeze Cycle Start Time 0: Italian 1: English 0: NO 1: YES --- --- D R/W s I R/W --- --- --- R --- --- 6.0 2.0 17.5 35.0 °C °C °C °C 0.0 1.0 Gfc34 Gfc34 50.0 20.0 Gfc34 Gfc34 0 --- 0 1 70.0 °C 0.0 99.9 Gc_03 Start cycle Day: 0: --1: ALP01 - Geothermal Flow Switch 2: ALP05 - Installation Flow Switch 3: ALP04 - ACS Pres. Thermal Overload Switch 4: ALP02 - Geo. Pres. Thermal Overload Switch 5: ALP03 - Inst. Pres. Thermal Overload Switch 6: ALC01 - Comp. 1 Thermal Overload Switch 7: ALC02 - Comp. 2 Thermal Overload Switch 8: ALB01 - High Pressure 1 9: ALB03 - High Pressure 2 10: ALB02 - Low Pressure 11: ALU01 - Geotherm. Antifreeze 12: ALU02 - Inst. Antifreeze 13: ALA01 - Probe B1 Fault 14: ALA02 - Probe B2 Fault 15: ALA03 - Probe B3 Fault 16: ALA04 - Probe B4 Fault 17: ALA05 - Probe B5 Fault 18: ALA06 - Probe B6 Fault 19: ALA07 - Probe B7 Fault 20: ALA08 - Probe B8 Fault 21: ALA09 - Probe B9 Fault 22: ALA10 - Probe B10 Fault 23: ALB04 - High Pres. Trans. 24: ALB05 - Low Pres.Trans. 60 Enable Antifreeze Cycle Antifreeze Cycle Water Set Point 0: No 1: Yes 0: No 1: Yes 0: No 1: Yes 0: No 1: Yes 0 --- 0 7 0: OFF 1: ON 0: --1: MONDAY 2: TUESDAY 3: WEDNESDAY 4: THURSDAY 5: FRIDAY 6: SATURDAY 7: SUNDAY --- R A A A A R/W R/W R/W R/W D R/W A R/W I R/W R/W 74 29 30 31 0 h 0 23 I Nominal Set Point (ON) in Chiller Operation 12.0 °C Hc_21 Hc_21 A R/W 36 Nominal Set Point (ON) in Heat Pump Operation Nominal Set Point (ON) of Domestic Water 38.0 50.0 °C °C Hc_21 Hc_22 Hc_21 Hc_22 A A R/W R/W 37 40 +030220741 Smart HP – rel. 1.0 - 05/09/2008 38 Mask Index Descr. display Descr. Def UOM Min Max Value description Type R/W BMS addr. Energy Save Setpoint Chiller : HP : Energy Saving Set Point in Chiller Operation Energy Saving Set Point in Heat Pump Operation 15.0 32.0 °C °C Hc_21 Hc_21 Hc_21 Hc_21 A A R/W R/W 38 39 DHW : Energy Saving Set Point for Domestic Water 50.0 °C Hc_22 Hc_22 A R/W 41 Compressor 1 : Compressor 2 : Geotherm. pump: Primary pump : DHW pump : Mix. pump : Solar pump 1 : Solar pump 2 : Compressor 1 Hour Counter Compressor 2 Hour Counter Geothermal Pump Hour Counter Primary Circuit Pump Hour Counter Domestic Circuit Pump Hour Counter Mixing Circuit Pump Hour Counter Solar Panel Pump 1 Hour Counter Solar Panel Pump 2 Hour Counter 0 0 0 0 0 0 0 0 kh kh kh kh kh kh kh kh 0 0 0 0 0 0 0 0 999 999 999 999 999 999 999 999 I I I I I I I I R R R R R R R R Communication prot. : BMS Protocol Settings 1 --- 0 3 I R/W Speed : BMS Speed Settings 4 --- 0 4 I R/W Address : Compressors: Pumps : Reset hour counter Compressor 1: Select Address No. for BMS Compressor Hour Counter Threshold Pump Hour Counter Threshold 1 99 99 --kh kh 0 0 0 207 999 999 I I I R/W R/W R/W Reset Compressor 1 Hour Counter 0 --- 0 1 D R/W Compressor 2 : Reset Compressor 2 Hour Counter 0 --- 0 1 D R/W Geotherm. pump : Reset Geothermal Pump Hour Counter 0 --- 0 1 D R/W Primary pump : Reset Primary Circuit Pump Hour Counter 0 --- 0 1 D R/W Reset hour counter DHW pump: Reset Domestic Pump Hour Counter 0 --- 0 1 D R/W Mix. pump : Reset Mixing Circuit Pump Hour Counter 0 --- 0 1 D R/W Solar pump 1 : Reset Solar Panel Pump 1 Hour Counter 0 --- 0 1 D R/W Solar pump 2 : Reset Solar Panel Pump 2 Hour Counter 0 --- 0 1 D R/W Probe calibration B1: Enable/disable Analogue Input B1 1 --- 0 1 D R/W Ofs: Probe: Probe B1 Calibration Value B1= Geothermal Outlet Water Temperature 0.0 --- °C °C -9.9 -99.9 9.9 99.9 A A R/W R B2: Enable/disable Analogue Input B2 1 --- 0 1 D R/W Ofs: Probe: Probe B2 Calibration Value B2= Geothermal Return Circuit Inlet Water Temperature 0.0 --- °C °C -9.9 -99.9 9.9 99.9 A A R/W R Probe calibration B3: Enable/disable Analogue Input B3 1 --- 0 1 D R/W Ofs: Probe: Probe B3 Calibration Value B3= Domestic Hot Water Temperature 0.0 --- °C °C -9.9 -99.9 9.9 99.9 A A R/W R Probe calibration B4: Enable/disable Analogue Input B4 1 --- 0 1 D R/W Ofs: Probe: Probe B4 Calibration Value B4= Mixing Circuit Outlet Water Temperature 0.0 --- °C °C -9.9 -99.9 9.9 99.9 A A R/W R B5: Enable/disable Analogue Input B5 1 --- 0 1 D R/W Ofs: Probe: Probe B5 Calibration Value B5= Primary Circuit Inlet Water Temperature 0.0 --- °C °C -9.9 -99.9 9.9 99.9 A A R/W R Probe calibration B4: Enable/disable Analogue Input B4 1 --- 0 1 D R/W Ofs: Probe: Probe B4 Calibration Value B4= Compressor Exhaust Gas Temperature 0.0 --- °C °C -9.9 -100 9.9 200 A A R/W R B5: Enable/disable Analogue Input B5 1 --- 0 1 D R/W Ofs: Probe: Probe B5 Calibration Value B5= Primary Circuit Inlet Water Temperature 0.0 --- °C °C -9.9 -99.9 9.9 99.9 A A R/W R Probe calibration B6: Enable/disable Analogue Input B6 1 --- 0 1 D R/W Ofs: Probe B6 Calibration Value B6= Outside Air Temperature (on unit type 3, 5 or 6) Gc_05 Gd_01 Gd_02 Ge_01 Gfa01 Gfa02 Gfa03 Gfb01 Gfb02 Gfb03 Gfb04 Gfb05 Probe: Gfb06 Gfb07 0: --1: CAREL RS485 2: ModBus RS485 3: pCOload local 0: 1200 1: 2400 2: 4800 3: 9600 4: 19200 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES 0: NO 1: YES Geotherm.outlet 0: NO 1: YES Geotherm.inlet 0: NO 1: YES Domest.water 0: NO 1: YES Mix circ.outlet 0: NO 1: YES System return 0: NO 1: YES Compress.disch. 0: NO 1: YES System return 0: NO 1: YES Ext.air temp. 0.0 °C -9.9 9.9 A R/W --- °C -99.9 99.9 A R 0: NO 1: YES System outlet Probe calibration B6: Enable/disable Analogue Input B6 1 --- 0 1 D R/W Ofs: Probe B6 Calibration Value 0.0 °C -9.9 9.9 A R/W Probe: B6= Primary Circuit Water Outlet Temperature (for unit type 4) --- °C -99.9 99.9 A R Probe calibration B7: Enable/disable Analogue Input B7 1 --- 0 1 D R/W Ofs: Probe: Probe B7 Calibration Value B7= High Pres. Transd. (unit type 3, 4) 0.0 --- Bar Bar -9.9 -1.0 9.9 99.9 A A R/W R B8: Enable/disable Analogue Input B8 1 --- 0 1 D R/W Ofs: Probe B8 Calibration Value 0.0 Bar -9.9 9.9 A R/W +030220741 Smart HP – rel. 1.0 - 05/09/2008 39 0: NO 1: YES Cond. press. 0: NO 1: YES Evapor. press. 1 2 3 4 5 5 35 12 7 Mask Index Descr. display Probe: Gfb08 Gfb10 0 1 -9.9 -99.9 9.9 99.9 1 --- 0 1 B8: Enable/disable Analogue Input B8 Ofs: Probe B8 Calibration Value B8= Solar Circuit Boiler Inlet Temperature (for unit type 6) B8= Mixing Circuit Outlet Water Temperature (for unit type 5) Probe calibration B9: Enable/disable Analogue Input B9 Ofs: Probe: Probe B9 Calibration Value B9= Solar Panel 1 Temperature B10: Enable/disable Analogue Input B10 Ofs: Probe: Probe Calibration Serial probe n° 01 Temperature Ofs: Temperature Probe: Humidity Probe: Probe Calibration Serial probe n° 02 Temperature Ofs: Temperature Probe: Humidity Probe: Probe Calibration Serial probe n° 03 Temperature Ofs: Temperature Probe: Humidity Probe: Probe Calibration Serial probe n° 04 Temperature Ofs: Temperature Probe: Humidity Probe: Probe Calibration Serial probe n° 05 Temperature Ofs: Temperature Probe: Humidity Probe: Probe Calibration Serial probe n° 06 Temperature Ofs: Temperature Probe: Humidity Probe: Probe Calibration Ext. serial probe Temperature Ofs: Temperature Probe: Humidity Probe: Enable control room zones: Modbus setting Baudrate Stop bit Parity mode Value description 0: NO 1: YES System outlet 0: NO 1: YES In mix circuit 0: NO 1: YES Return solar Type R/W BMS addr. A R 6 D R/W A A R/W R D R/W 1 --- 0 1 D R/W --- -9.9 9.9 A R/W --- °C -99.9 99.9 A R 9 --- °C -99.9 99.9 A R 4 D R/W A A R/W R D R/W 0: NO 1: YES Solar coll.1 1 --- 0 1 °C °C -9.9 -100 9.9 200 1 --- 0 1 Probe B10 Calibration Value B10= Solar Panel 2 Temperature 0.0 --- °C °C -9.9 -100 9.9 200 A A R/W R Temperature Calibration Value Serial Probe No. 01 0.0 R/W 0: NO 1: YES Solar coll.2 °C -10.0 10.0 A Serial Probe No. 01 Temperature Humidity Calibration Value Serial Probe No. 01 Serial Probe No. 01 Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R Temperature Calibration Value Serial Probe No. 02 0.0 °C -10.0 10.0 A R/W Serial Probe No. 02 Temperature Humidity Calibration Value Serial Probe No. 02 Serial Probe No. 02 Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R Temperature Calibration Value Serial Probe No. 03 0.0 °C -10.0 10.0 A R/W Serial Probe No. 03 Temperature Humidity Calibration Value Serial Probe No. 03 Serial Probe No. 03 Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R Temperature Calibration Value Serial Probe No. 04 0.0 °C -10.0 10.0 A R/W Serial Probe No. 04 Temperature Humidity Calibration Value Serial Probe No. 04 Serial Probe No. 04 Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R Temperature Calibration Value Serial Probe No. 05 0.0 °C -10.0 10.0 A R/W Serial Probe No. 05 Temperature Humidity Calibration Value Serial Probe No. 05 Serial Probe No. 05 Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R Temperature Calibration Value Serial Probe No. 06 0.0 °C -10.0 10.0 A R/W Serial Probe No. 06 Temperature Humidity Calibration Value Serial Probe No. 06 Serial Probe No. 06 Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R Temperature Calibration Value Outside Serial Probe 0.0 °C -10.0 10.0 A R/W Outside Serial Probe Temperature Humidity Calibration Value Outside Serial Probe Outside Serial Probe Humidity --- °C -30.0 70.0 A R 0.0 % -10.0 10.0 A R/W --- % 0.0 99.9 A R I R/W I R/W I R/W I R/W I R/W On-screen selection of Ambient Control System 0 --- 0 2 0 --- 0 6 ModBus Protocol Speed Setting for Serial Probes and Clima ModBus Protocol Stop Bit Setting for Serial Probes and Clima ModBus Protocol Parity Bit Setting for Serial Probes and Clima +030220741 Smart HP – rel. 1.0 - 05/09/2008 12 0.0 0.0 --- Number probes/Clima required: Indicates the number of devices in a room to be activated Gfc02 99.9 --°C Humidity Ofs: Gfc01 -1.0 --- Humidity Ofs: Gfb16 Bar 1 Humidity Ofs: Gfb15 --- 0.0 --- Humidity Ofs: Gfb14 Max Probe B7 Calibration Value B7= Primary Circuit Outlet Water Temperature Humidity Ofs: Gfb13 Min Enable/disable Analogue Input B7 Humidity Ofs: Gfb12 UOM Ofs: Probe: Humidity Ofs: Gfb11 B8= Low Pres. Transd. (unit type 3, 4) Def Probe calibration B7: Probe: Gfb09 Descr. 40 4 --- 0 4 1 --- 0 1 0 --- 0 1 0: NONE 1: PROBES 2: CLIMA 0: 1200 1: 2400 2: 4800 3: 9600 4: 19200 0: 1 1: 2 0: NONE 1: EVEN 10 11 Mask Index Descr. display Timeout Serial probe n° 01 Enabled: Address: Gfc03 ModBus Protocol Response Time Delay Setting for Serial Probes and Clima 300 ms 100 5000 0 --- 0 1 128 --- 128 159 Enable Serial Probe No. 01 Dipswitch address of Serial Probe No. 01 0 1 Type: Installed Probe Type Setting 0 --- 0 1 Enable Serial Probe No. 02 Dipswitch address of Serial Probe No. 02 0 --- 0 1 128 --- 128 159 No. of zones: Assign Scheduler/Zone for Serial Probe No. 02 0 --- 0 1 Type: Installed Probe Type Setting 0 --- 0 1 Enable Serial Probe No. 03 Dipswitch address of Serial Probe No. 03 0 --- 0 1 128 --- 128 159 No. of zones: Assign Scheduler/Zone for Serial Probe No. 03 0 --- 0 1 Type: Installed Probe Type Setting 0 --- 0 1 Enable Serial Probe No. 04 Dipswitch address of Serial Probe No. 04 0 --- 0 1 128 --- 128 159 No. of zones: Assign Scheduler/Zone for Serial Probe No. 04 0 --- 0 1 Type: Installed Probe Type Setting 0 --- 0 1 Enable Serial Probe No. 05 Dipswitch address of Serial Probe No. 05 0 --- 0 1 128 --- 128 159 No. of zones: Assign Scheduler/Zone for Serial Probe No. 05 0 --- 0 1 Type: Installed Probe Type Setting 0 --- 0 1 Serial probe n° 06 Enabled: Address: Gfc08 Max --- Serial probe n° 05 Enabled: Address: Gfc07 Min 0 Serial probe n° 04 Enabled: Address: Gfc06 UOM Assign Scheduler/Zone for Serial Probe No. 01 Serial probe n° 03 Enabled: Address: Gfc05 Def No. of zones: Serial probe n° 02 Enabled: Address: Gfc04 Descr. No. of zones: Enable Serial Probe No. 06 0 --- 0 1 128 --- 128 159 Assign Scheduler/Zone for Serial Probe No. 06 0 --- 0 1 --- 0 1 Dipswitch address of Serial Probe No. 06 Type: Installed Probe Type Setting 0 Clima n° 01 Status: Address: Operating status of CLIMA No. 01 Clima No. 1 Parameter Address 0 --- 0 1 0 --- 0 999 No. of zones: Assign Scheduler/Zone for Clima No. 01 0 --- 0 1 Model: Reading of control type for CLIMA No. 01 0 --- 0 7 Clima n° 01 Lock: Block Clima No. 1 Keypad 0 --- 0 2 Menu password: Clima n° 02 Status: Address: Access Password for Clima No. 01 Operating status of CLIMA No. 02 Clima No. 02 Parameter Address 0 --- 0 999 0 --- 0 1 0 --- 0 999 No. of zones: Assign Scheduler/Zone for Clima No. 02 0 --- 0 1 Model: Reading of control type for CLIMA No. 02 0 --- 0 7 Clima n° 02 Lock: Block Clima No. 02 Keypad 0 --- 0 2 Menu password: Access Password for Clima No. 02 0 --- 0 999 Clima n° 03 Status: Address: Operating status of CLIMA No. 03 Clima No. 03 Parameter Address 0 --- 0 1 0 --- 0 999 No. of zones: Assign Scheduler/Zone for Clima No. 03 0 --- 0 1 Gfc09 Gfc10 Gfc11 Gfc12 Gfc13 +030220741 Smart HP – rel. 1.0 - 05/09/2008 41 Value description 0: NO 1: YES 0: 2 1: 1 0: TEMPERATURE 1: TEMP.+HUMID. 0: NO 1: YES 0: 2 1: 1 0: TEMPERATURE 1: TEMP.+HUMID. 0: NO 1: YES 0: 2 1: 1 0: TEMPERATURE 1: TEMP.+HUMID. 0: NO 1: YES 0: 2 1: 1 0: TEMPERATURE 1: TEMP.+HUMID. 0: NO 1: YES 0: 2 1: 1 0: TEMPERATURE 1: TEMP.+HUMID. 0: NO 1: YES 0: 2 1: 1 0: TEMPERATURE 1: TEMP.+HUMID. 0: Off 1: On 0: 2 1: 1 0: T+Hrd 1: H 2: T 3: T+H 4: T2 5: T2+H 6: T2A 7: T2A+H 0: NOT LOCKED 1: UP-DOWN-PRG 2: ONLY PRG 0: Off 1: On 0: 2 1: 1 0: T+Hrd 1: H 2: T 3: T+H 4: T2 5: T2+H 6: T2A 7: T2A+H 0: NOT LOCKED 1: UP-DOWN-PRG 2: ONLY PRG 0: Off 1: On 0: 2 1: 1 Type R/W I R/W D R/W I R/W D R/W D R/W D R/W I R/W D R/W D R/W D R/W I R/W D R/W D R/W D R/W I R/W D R/W D R/W D R/W I R/W D R/W D R/W D R/W I R/W D R/W D R/W D R I R/W D R/W I R I R/W I R/W D R I R/W D R/W I R I R/W I R/W D R I R/W D R/W BMS addr. Mask Index Descr. display Descr. Def UOM Min Max Value description Type R/W I R Model: Reading of control type for CLIMA No. 03 0 --- 0 7 0: T+Hrd 1: H 2: T 3: T+H 4: T2 5: T2+H 6: T2A 7: T2A+H Clima n° 03 Lock: Block Clima No. 03 Keypad 0 --- 0 2 0: NOT LOCKED 1: UP-DOWN-PRG 2: ONLY PRG I R/W Menu password: Clima n° 04 Status: Address: Access Password for Clima No. 03 Operating status of CLIMA No. 04 Clima No. 04 Parameter Address 0 --- 0 999 I R/W 0 --- 0 1 0: Off 1: On D R 0 --- 0 999 I R/W No. of zones: Assign Scheduler/Zone for Clima No. 04 0 --- 0 1 D R/W Model: Reading of control type for CLIMA No. 04 0 --- 0 7 I R Clima n° 04 Lock: Block Clima No. 04 Keypad 0 --- 0 2 I R/W Menu password: Clima n° 05 Status: Address: Access Password for Clima No. 04 Operating status of CLIMA No. 05 Clima No. 05 Parameter Address 0 --- 0 999 I R/W 0 --- 0 1 0 --- 0 999 No. of zones: Assign Scheduler/Zone for Clima No. 05 0 --- 0 1 Model: Reading of control type for CLIMA No. 05 0 --- 0 7 Clima n° 05 Lock: Block Clima No. 05 Keypad 0 --- 0 2 Menu password: Clima n° 06 Status: Address: Access Password for Clima No. 05 Operating status of CLIMA No. 06 Clima No. 06 Parameter Address 0 --- 0 999 0 --- 0 1 0 --- 0 999 No. of zones: Assign Scheduler/Zone for Clima No. 06 0 --- 0 1 Model: Reading of control type for CLIMA No. 06 0 --- 0 7 Gfc20 Clima n° 06 Lock: Block Clima No. 06 Keypad 0 --- 0 2 Menu password: Access Password for Clima No. 06 0 --- 0 999 Gfc21 External serial probe: Enable/disable Outside Serial Probe 0 --- 0 1 Gfc22 Ext. serial probe n° 07 Enabled: Address: Gfc14 Gfc15 Gfc16 Gfc17 Gfc18 Gfc19 Gfc23 Enable Serial Probe No. 07 Dipswitch address of Serial Probe No. 07 0 --- 0 1 128 --- 128 159 Type: Installed Probe Type Setting 0 --- 0 1 N. solar collectors: Set No. Solar Panels 0 --- 0 2 Alm T. D.H.W.: Max T. D.H.W.: Max T.Solar: ACS Max. Temp Limit ACS Maximum Attainable Temperature Solar Panels Maximum Attainable Temperature 75.0 85.0 140.0 °C °C °C 20.0 0.0 0.0 99.9 99.9 200.0 System integration Select Installation Integration (NONE, FURNACE, ELEC. HEATER) 0 --- 0 2 Request as: Type of installation integration operation (CP integration, CP replacement) 0 --- 0 1 DHW integration Select ACS integration (NONE, FURNACE, ELEC. HEATER) 0 --- 0 2 Request as: Type of domestic integration operation (CP integration, CP replacement) 0 --- 0 1 Gfc24 Gfc25 +030220741 Smart HP – rel. 1.0 - 05/09/2008 42 0: 2 1: 1 0: T+Hrd 1: H 2: T 3: T+H 4: T2 5: T2+H 6: T2A 7: T2A+H 0: NOT LOCKED 1: UP-DOWN-PRG 2: ONLY PRG 0: Off 1: On 0: 2 1: 1 0: T+Hrd 1: H 2: T 3: T+H 4: T2 5: T2+H 6: T2A 7: T2A+H 0: NOT LOCKED 1: UP-DOWN-PRG 2: ONLY PRG 0: Off 1: On 0: 2 1: 1 0: T+Hrd 1: H 2: T 3: T+H 4: T2 5: T2+H 6: T2A 7: T2A+H 0: NOT LOCKED 1: UP-DOWN-PRG 2: ONLY PRG 0: NOT PRESENT 1: PRESENT 0: NO 1: YES 0: TEMPERATURE 1: TEMP.+HUMID. 0: NOT PRESENT 1: 1 COLLECTOR ACTIVE 2: 2 COLLECTORS ACTIVE D R I R/W D R/W I R I R/W I R/W D R I R/W D R/W I R I R/W I R/W D R/W D R/W I R/W D R/W I R/W A A A R/W R/W R/W 0: NONE 1: BOILER 2: EL. HEATERS 0: INTEGRATE HP 1: REPLACE HP 0: NONE 1: BOILER 2: EL. HEATERS I R/W D R/W I R/W 0: INTEGRATE HP 1: REPLACE HP D R/W BMS addr. Mask Index Descr. display Descr. Def UOM Min Max Enable boiler based on the: Activation of furnace as a function of: OUTSIDE AIR TEMP. or GEOTHERMAL RETURN TEMP.) 0 --- 0 1 Boiler activation delay: Furnace Activation Delay Time 5 min 0 999 Boiler setting: Setpoint sys.: Diff.System: Setpoint DHW: Diff. DHW: Heaters setting: Diff. On sys..: Activation set point (for installation) of furnace on outside air or geo. return Furnace Activation Differential Furnace Activation Set Point for Domestic Water Furnace Activation Differential for Domestic Water Differential, with respect to operational set point, for activation of integrating heaters of the installation Differential, with respect to operational set point, for deactivation of integrating heaters of the installation Installation heater activation delay time Differential, with respect to operational set point, for activation of integrating heaters of the domestic water Differential, with respect to operational set point, for deactivation of integrating heaters of the domestic water Value description 0: OUTSIDE AIR T. 1: GEOTHERMAL RETURN T. Type R/W D R/W I R/W BMS addr. Gfc26 Gfc27 Diff. Off sys.: Gfc28 Delay On: Diff. On DHW: Diff. Off DHW: Gfc30 Gfc31 Gfc32 Gfc33 Gfc34 Gfc35 Gfc36 Gfc37 Gfc38 5.0 °C -50.0 50.0 A R/W 3.0 35.0 5.0 °C °C °C 0.0 0.0 0.0 20.0 70.0 20.0 A A A R/W R/W R/W 8.0 °C 0.0 30.0 A R/W 5.0 °C 0.0 30.0 A R/W 60 s 0 999 I R/W 10.0 °C 0.0 30.0 A R/W 5.0 °C 0.0 30.0 A R/W D R/W A A R/W R/W A R/W D R/W A I R/W R/W D R/W A R/W 32 33 Temperature control mix circ.: Mixing Circuit Outlet Temperature Control 1 --- 0 1 External T set: % compensation: Anti-sweat function Mix circ. temp. offset in auto mode:: Type of valve control 3 way system: Prop. band: Integr. time: Reverse logic system 3way mix valve: Outlet temp. limits Mix circuit water: Min cooling: Max heating: Antifreeze alarm setp. Geotherm circ.: Geothermal antifreeze alarm setpoint: Reset antifreeze alarm Geotherm circ.: System antifreeze alarm setpoint: System antifreeze alarm diff. : Reset antifreeze alarm system side: Temperature Set Point for Compensation Start Compensation Ramp Slope 7.0 80 --% -99.9 0 99.9 100 Mixing Circuit Temperature Offset (cooling) 3.0 °C 0.0 9.9 Type of humidifier: Gfc41 Gfc42 1 --- 0 1 Proportional band for mixing valve Mixing Valve Control Integration Time 4.0 30 °C s 2.0 1 99.9 999 Mixing Circuit 3-way Valve Logic Inversion 0 --- 0 1 Mixing Circuit Water Outlet Temperature Minimum Limit 12.0 °C 5.0 99.9 Mixing Circuit Water Outlet Temperature Maximum Limit 45.0 °C 20.0 99.9 A R/W Geothermal Circuit Antifreeze Alarm Set Point 4.0 °C -99.9 99.9 A R/W Geothermal Circuit Antifreeze Alarm Differential 3.0 °C 0.5 99.9 A R/W D R/W Geothermal Circuit Antifreeze Alarm Reset Type 1 --- 0 1 Gfc43 Gfc44 4.0 °C -99.9 99.9 A R/W 3.0 °C 0.5 99.9 A R/W Installation Side Antifreeze Alarm Reset Type 1 --- 0 1 D R/W Enable Modulating Humidifier 0 --- 0 1 D R/W D R/W A A A A R/W R/W R/W R/W D R/W Enable Dehumidifier On/Off Dehumidifier working differential Humidifier Working Band Measured Humidity Minimum Limit Set Point Measured Humidity Maximum Limit Set Point 0 --- 0 1 ----% % 0.0 0.0 0.0 50.0 99.9 99.9 50.0 99.9 1 --- 0 1 Cooling Ambient Temperature Set Point Minimum Limit 18.0 °C 0.0 99.9 A R/W 18 Cooling Ambient Temperature Set Point Max. Limit Heating Ambient Temperature Set Point Min. Limit Heating Ambient Temperature Set Point Max. Limit Cooling Ambient Humidity Set Point Minimum Limit Cooling Ambient Humidity Set Point Maximum Limit 30.0 15.0 25.0 30.0 °C °C °C % Gfc43 0.0 Gfc43 0.0 99.9 99.9 99.9 99.9 A A A A R/W R/W R/W R/W 17 20 19 25 70.0 % 0.0 99.9 A R/W 26 30.0 70.0 % % 0.0 0.0 99.9 99.9 A A R/W R/W 27 28 0 --- 0 1 I R/W D R/W Activate pump in system circuit: Primary Circuit Pump Active Heating Ambient Humidity Set Point Minimum Limit Heating Ambient Humidity Set Point Maximum Limit Enable protection Protection Function Active for Rooms 0 --- 0 1 Set protection Protection Function Intervention Set Point --- °C 0.0 99.9 Gfc47 Recovery fan: Recovery Fans Enabled 0 --- 0 1 Gfc48 Diff. valve zone Summer: Cooling valve activation temperature differential (Zone 1=Zone 2) 1.5 °C 0.0 Winter: Heating valve activation temperature differential (Zone 1=Zone 2) 2.0 °C Enable lighting digital output NO8 with minor alarms: Setpoint geo pump Summer: Winter: Enable GENERAL ALARM relay activation even with minor alarms Cooling Set Point for Control of Modulating Geothermal Pump Heating Set Point for Control of Modulating Geothermal 0 --- Gfc46 Gfc48 Gfc49 Gfc50 0: AUTO 1: MANUAL 0: NOT PRESENT 1: MODULATING 0: NOT PRESENT 1: ON/OFF 5.0 5.0 10.0 90.0 Min heating: Max heating: Cooling/Heating Select season from: Gfc45 0: AUTO 1: MANUAL Installation Antifreeze Alarm Activation Differential Type of dehumidifier: Max cooling: 0: DIRECT 1: INVERSE Installation Side Antifreeze Alarm Set Point Dehumidification diff: Humidification band: Min humidity limit measured: Max humidity limit measured: Set temperature limits Min cooling: Max cooling: Min heating: Max heating: Set humidity limits Min cooling: 0: P 1: P+I Installation 3-way Valve Temperature Control Gfc39 Gfc40 0: FIXED POINT 1: DYNAMIC Cooling/Heating Selection +030220741 Smart HP – rel. 1.0 - 05/09/2008 0: UNIT ON 1: ON REQUEST 0: KEYBOARD 1: B.M.S. 0: NO 1: YES A R/W D R/W 9.9 A R/W 0.0 9.9 A R/W 0 1 D R/W 0: DISABLE 1: ENABLE 0: NO 1: YES 35.0 °C -99.9 99.9 A R/W 6.5 °C -99.9 99.9 A R/W 43 Mask Index Descr. display Descr. Def UOM Min Max Value description Type R/W Cooling Working Band for Modulating Geothermal Pump 3.0 °C 0.0 9.9 A R/W Heating Working Band for Modulating Geothermal Pump 3.0 °C 0.0 9.9 A R/W D R/W I R/W D R/W D R/W D R/W D R/W D R/W D R/W D R/W I I R/W R D R I R D R/W I I I I R/W R/W R/W R/W D R I R/W D R/W I R/W D R/W D R/W D R/W D R/W D R/W D R/W Pump Gfc51 Gfd01 Band geo pump Summer: Winter: Delete alarm log: Allow deletion of Alarm Log 0 --- 0 1 Enter new service password (PW1): Select New Service Password 1234 --- 0 9999 NO2 Geo circ. pump: Geothermal Installation Pump Manual Start 0 --- 0 1 NO3 System pump: Installation Pump Manual Start 0 --- 0 1 NO4 DHW circ. pump: ACS Pump Manual Start 0 --- 0 1 NO5 Mix circ. pump: Mixing Installation Pump Manual Start 0 --- 0 1 NO15 Solar pump 1: Solar Circuit Pump 1 Manual Start 0 --- 0 1 NO16 Solar pump 2: Solar Circuit Pump 2 Manual Start 0 --- 0 1 EEV mode Electronic Expansion Valve Manual Positioning 0 --- 0 1 Requested step EEV position Number of steps requested Letter of current number of steps 0 0 ----- 0 0 9999 9999 Unit waiting for: 0 --- 0 1 Message for any faults of EVD400 Driver 0 --- 0 3 Gg_01 Gg_02 Gg_03 Gg_04 Gg_05 Ha_01 Ha_02 Ha_03 0: NO 1: YES 0: AUT 1: MAN 0: AUT 1: MAN 0: AUT 1: MAN 0: AUT 1: MAN 0: AUT 1: MAN 0: AUT 1: MAN 0: AUTO 1: MAN. 0: 1: System waiting for 0: NO WARNINGS 1: VALVE OPEN RESTART 2: BATT CHARGED RESTART 3: EEPROM ERROR RESTART 0: NO 1: YES Go ahead? Select to Bypass Error 0 --- 0 1 S1 S2 S3 PT1000 EVD400 Driver Probe S1 Offset EVD400 Driver Probe S2 Offset EVD400 Driver Probe S3 Offset EVD400 Driver Probe S2 (PT1000) Offset 0.0 0.0 0.0 0.0 °C/bar °C/bar °C/bar °C -9.9 -9.9 -9.9 -01.0 9.9 9.9 9.9 10.0 Unit with selection of up to 2 compressors 1 --- 0 1 Set unit configuration type 5 --- 1 6 Electronic Valve driver present EVD400: Enable EVD400 Valve Driver 0 --- 0 1 Total no. Of comps.: Total number of compressors 2 --- 1 2 Comp. 1: Compressor No. 1 Enabled 1 --- 0 1 Comp. 2: Compressor No. 2 Enabled 1 --- 0 1 ID01 Geo flow switch: Invert Geothermal Side Flow Switch Logic 0 --- 0 1 ID02 Comp. 1 overload: Invert Compressor 1 Thermal Overload Switch Logic 0 --- 0 1 ID03 High press. comp. 1: Invert Compressor 1 High Pressure Switch Logic 0 --- 0 1 ID04 Low press. switch : Invert Low Pressure Switch Logic 0 --- 0 1 ID05 Geo pump overload : Invert pump thermal overload switch logic (on unit type 1 or 2), geothermal pump thermal overload switch (on unit type 3, 4, 5 or 6) 0 --- 0 1 0: NC 1: NO D R/W ID06 Sys. pump overload : Invert ACS heater thermal overload switch (on unit type 1 or 2); installation pump thermal overload switch (on units type 3, 4, 5 or 6) 0 --- 0 1 0: NC 1: NO D R/W ID07 Boiler alarm : Invert Furnace Alarm Logic 0 --- 0 1 D R/W ID08 Remote On/Off : Invert On/Off Remote Logic 0 --- 0 1 D R/W ID09 Comp. 2 overload: Invert Compressor 2 Thermal Overload Switch Logic 0 --- 0 1 D R/W ID10 High press. comp. 2 : Invert Compressor 2 High Pressure Switch Logic 0 --- 0 1 D R/W ID11 DHW pump overload : Invert ACS Pump Thermal Overload Switch Logic 0 --- 0 1 D R/W ID12 Sys. Circ. flow sw. : Invert installation circuit flow switch logic (on unit type 4, 5 or 6); mixing installation pump thermal overload switch (on unit type 3) 0 --- 0 1 D R/W ID13 Humidifier alarm : Invert Humidifier Alarm Logic 0 --- 0 1 D R/W ID14 DHW heater overload : Invert ACS Heater Thermal Overload Switch Logic 0 --- 0 1 D R/W Type of unit: Hb_01 Hb_02 Hb_03 Hb_04 Hb_05 Hb_06 Hb_07 +030220741 Smart HP – rel. 1.0 - 05/09/2008 44 0: One compressor 1: Two Compressors 1: Basic heating 2: Heating + DHW 3: Heating + DHW 4: Reversing + DHW 5: Reversing + Driver + DHW 6: Rev. + Driver + DHW + Solar 0: NOT PRESENT 1: PRESENT 1: 1 compressor 2: 2 compressors 0: DISABLE 1: ENABLE 0: DISABLE 1: ENABLE 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO BMS addr. Mask Index Descr. display Descr. Def UOM Min Max Value description 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: NC 1: NO 0: --1: 0..10Vdc 2: 0..5Vdc 3: 4..20mA Type R/W D R/W D R/W D R/W D R/W D R/W I R/W A A R/W R/W I R/W ID15 Mix pump overload : Invert Mixing Pump Thermal Overload Switch Logic 0 --- 0 1 ID16 Dehumidifier alarm : Invert Dehumidifier Alarm Logic 0 --- 0 1 ID17 Solar pump 1 overl. : Invert Solar Pump 1 Thermal Overload Switch Logic 0 --- 0 1 ID18 Solar pump 2 overl. : Invert Solar Pump 2 Thermal Overload Switch Logic 0 --- 0 1 Hb_10 Reverse logic 4-way valve: Invert Heat Pump Cycle Inversion 4-way Valve Logic 0 --- 0 1 B7 = High pressure Type: Select High Pressure Transducer Type (unit 3 or 4) 2 --- 0 3 min: max: High Pressure Transducer Minimum Limit High Pressure Transducer Maximum Limit 0.0 34.5 bar bar -01.0 -01.0 99.9 99.9 B8 = Low pressure Type: Select Low Pressure Transducer Type (unit 3 or 4) 2 --- 0 3 min: max: Set high pressure compressor/s: High press. hyst.: Set low pressure compressor/s: Low press. hyst.: Low pressure alarm delay time at start compressor/s: Low pres. alarm delay time in steady operat. compressor/s: Low Pressure Transducer Minimum Limit Low Pressure Transducer Maximum Limit Set High Pressure Compressor(s) High Pressure Compressor(s) Hysteresis Set Low Pressure Compressor(s) Low Pressure Compressor(s) Hysteresis -1.0 9.3 25.0 2.0 1.5 0.5 bar bar bar bar bar bar -01.0 -01.0 0.0 0.0 0.0 0.5 99.9 99.9 50.0 9.9 50.0 99.9 A A A A A A R/W R/W R/W R/W R/W R/W Low Pressure Alarm Delay Time for Compressor(s) Start 40 s 0 999 I R/W Low Pressure Alarm Delay Time while compressor(s) in steady operating conditions 10 s 0 999 I R/W D R/W Hb_08 Hb_09 Hb_11 Hb_12 Hc_01 Hc_02 Hc_03 Hc_04 Hc_05 Hc_06 Hc_07 Hc_08 Hc_09 Hc_10 Reset low pressure alarm: Low Pressure Compressor(s) Alarm Reset Type Type of proportional or integral control of compressor Type of comp.Cont.: operation Sys. prop. band: Differential compressor start from installation request Integral time: Compressor Control Integration Time DHW prop. band: Domestic Hot Water Differential Minimum compressor ON time: Minimum ON Time for Compressor Minimum compressor OFF time: Minimum OFF Time for Compressor Min. time between two starts of Minimum time between starts of the same compressor same compressor: Min. time between starts of Minimum time between starts of different compressors different compressors: Compressor rot.: Enable Compressor Rotation Delay between On compressor from On system pump: System pump Off delay time from compres. Off: Delay between On compressors from On geo. pump: Geotherm. pump Off delay time from compres. Off: System flow switch alarm delay time at pump start: Alarm delay time System flow switch in steady op.: Delay time between compressor ON and installation pump ON Delay time between installation pump OFF and compressor OFF Delay time between compressor ON and geothermal pump ON Delay time between geothermal pump OFF and compressor OFF Delay time between installation flow switch alarm and start of pump Delay time for installation in steady operating conditions flow switch alarm Hc_17 Reset sys.Flow switch: Reset Installation Flow Switch Hc_18 Geothermal flow switch alarm delay time at pump start: Hc_19 Hc_11 Hc_12 Hc_13 Hc_14 Hc_15 Hc_16 1 0 --- 0 1 D R/W 3.0 60 4.0 60 60 °C s °C s s 0.5 1 0.5 0 0 15.0 999 15.0 900 900 A I A I I R/W R/W R/W R/W R/W 300 s 0 900 I R/W 10 s 0 900 I R/W D R/W 0: NO 1: YES 0 1 30 s 0 9999 I R/W 120 s 0 9999 I R/W 30 s 0 9999 I R/W 30 s 0 9999 I R/W 15 s 0 999 I R/W 5 s 0 999 0 --- 0 1 Delay time between geothermal flow switch alarm and start of pump 15 s 0 Alarm delay time Geotherm. flow switch in steady op.: Delay time for geothermal flow switch alarm in steady operating conditions 5 s Reset geo flow switch: Reset Geothermal Flow Switch 0 Verif.Stato iniziale flussostati: Enable check of flow switches (geothermal and installation) when pump started Limiti temp. Water temp. Limits Chiller Min: Chiller Max: PdC Min: PdC Max: Temperature limits DHW Min : DHW Max : Hda01 0 --- Hc_22 Hc_23 --- 0: AUTO 1: MANUAL 0: P 1: P+I 1 Hc_20 Hc_21 0 0: --1: 0..10Vdc 2: 0..5Vdc 3: 4..20mA I R/W D R/W 999 I R/W 0 999 I R/W --- 0 1 D R/W 0 --- 0 1 D R/W Chiller minimum set point limit can be set per unit 7.0 °C 0.0 99.9 A R/W Chiller maximum set point limit can be set per unit Heat pump minimum set point limit can be set per unit Heat pump maximum set point limit can be set per unit Domestic water minimum set point limit can be set per unit Domestic water maximum set point limit can be set per unit 17.0 20.0 50.0 °C °C °C 0.0 0.0 0.0 99.9 99.9 99.9 A A A R/W R/W R/W 20.0 °C 0.0 99.9 A R/W 70.0 °C 0.0 99.9 A R/W D R/W I R/W I R/W Sel.Sanitary pump: Select heat pump operation in heating 1 --- 0 1 EVD parameters EVD type Type of serial used by EVD400 1 --- 1 2 EVD probes type Type of probe connected to EVD400 0 --- 0 5 +030220741 Smart HP – rel. 1.0 - 05/09/2008 45 0: AUTO 1: MANUAL 0: AUTO 1: MANUAL 0: NO 1: YES 0: ALWAYS ENABLE 1: BY THERMOSTAT 1: EVD400 pLAN 2: EVD400 tLAN 0: NOT SELECTED 1: SHeat NTC-P(4-20)mA 2: SHeat NTC-P(raz) 3: SHeat NTC-NTC BMS addr. Mask Index Descr. display Descr. Def UOM Min Max Assigned position for probes 0 --- 0 5 Valve type Type of valve connected 0 --- 0 14 Refrigerant Type of refrigerant used 0 --- 0 13 0 --- 0 1 Hda02 Hda03 Hda05 4: SHeat Pt1000-P 5: SHeat NTCht-P(raz) 0: 1: 2: NTC>S3 P(raz)>S1 3: NTCsuct>S3 NTCsat>S1 4: Pt1000>S2 P(raz)>S1 5: NTCht>S2 P(raz)>S1 0: NOT SELECTED 1: ALCO EX5 2: ALCO EX6 3: ALCO EX7 4: ALCO EX8 330 step/s 5: SPORLAN 0.5-20tons 6: SPORLAN 25-30tons 7: SPORLAN 50-250tons 8: CAREL E2V**P 9: CAREL E2V 10: DANFOSS ETS-25/50 11: DANFOSS ETS-100 12: DANFOSS ETS-250/400 13: CUSTOM 14: ALCO EX8 500 step/s 0: --1: R22 2: R134a 3: R404a 4: R407c 5: R410a 6: R507c 7: R290 8: R600 9: R600a 10: R717 11: R744 12: R728 13: R1270 0: N 1: Y Type R/W I R I R/W I R/W D R/W Battery enable: Coil Module Present Custom valve config. Minimum steps Maximum steps Closing/Opening steps Minimum steps for custom valve 0 --- 0 8100 I R/W Maximum steps for custom valve Closure/Aperture Steps for Custom Valve 0 0 ----- 0 0 8100 8100 I I R/W R/W Opening EXTRAs Enable Extra Aperture Steps 0 --- 0 1 D R/W D R/W Closing EXTRAs Hda04 Value description 0: N 1: Y 0: N 1: Y Enable Extra Closure Steps 0 --- 0 1 Current of Moving Valve 0 mA 0 1000 I R/W Current of Dwell Valve Control Frequency 0 32 mA Hz 0 32 1000 501 I I R/W R/W Duty cycle Duty cycle used 0 % 0 100 I R/W EEV position with 0% power demand standby steps S1 probe limits Pressure limits Min value Number of steps of the valve in standby 0 --- 0 8100 I R/W Set the minimum value of the low pressure probe connected -1.0 barg -9.9 99.9 I R/W Set the maximum value of the low pressure probe connected 9.3 barg 0.0 99.9 I R/W I R/W Custom valve config. Phase current Still current Step rate Hda06 Max value Aux.probe conf. Type of Auxiliary Probe Connected Aux.probe limits Min value Set the minimum value of the auxiliary probe (high pressure) connected Set the maximum value of the auxiliary probe (high pressure) connected 1 --- 0 4 -1.0 °C/barg -99.9 99.9 I R/W 9.3 °C/barg -99.9 99.9 I R/W Hda07 Max value 0: NOT SELECTED 1: PRESSURE 2: NTC 3: NTC HT 4: PT 1000 Alarm Delay for Low Superheating 120 s 0 600 I R/W Hda08 Alarms delay Low SuperHeat High SuperHeat LOP MOP Probe error Alarm Delay for High Superheating Alarm Delay for Low Evaporation Pressure Alarm Delay for High Evaporation Pressure Alarm Delay for Probe Error 20 120 0 10 min s s s 0 0 0 0 600 600 600 999 I I I I R/W R/W R/W R/W Hda09 Stand alone Enable Stand Alone 0 --- 0 1 D R/W 60 % 0 100 I R/W I R/W EVD Autosetup Circuit/EEV ratio Hdb01 Percent Aperture on Start for startup opening Hdb02 Compressore or unit Type of Compressor Used +030220741 Smart HP – rel. 1.0 - 05/09/2008 0 46 --- 0 5 0: NO 1: YES 0: NOT SELECTED 1: RECIPROCATING 2: SCREW 3: SCROLL BMS addr. Mask Index Descr. display Descr. Capacity control Type of Compressor Capacity-control Evaporator type Cool Type of Evaporator / Condenser Def UOM Min Max 0 --- 0 3 0 --- 0 4 0 --- 0 4 Hdb02 Heat Min saturation temp. Cooling mode Hdb03 Heating mode Defrost mode Max saturation temp. Cooling mode Hdb04 Heating mode Defrost mode High SuperHeat alarm threshold Hdb05 Auto SuperHeat Man param. CH-Circuit/EEV Ratio Auto Hdc01 CH-Proportional gain Auto CH-Integral time Auto HP-Circuit/EEV Ratio Auto HP-Proportional gain Auto Hdc02 HP-Integral time Auto Type of Evaporator / Condenser Temperature at LOP Operating Pressure Minimum in Chiller Temperature at LOP Operating Pressure Minimum in Heat Pump Temperature at LOP Operating Pressure Minimum in Defrost Temperature at MOP Operating Pressure Maximum in Chiller Temperature at MOP Operating Pressure Maximum in Heat Pump Temperature at MOP Operating Pressure Maximum in Defrost Hdc03 DF-Proportional gain Auto DF-Integral time Auto SuperHeat deadzone +/- Auto Hdc04 Derivative time Auto Low SuperHeat int.time Auto Hdc05 LOP integral time Auto MOP integral time Auto Hdc06 MOP startup delay Auto Dynamic proportional gain? Hdc07 Blocked valve check Auto Hdc08 High Tcond.protection Auto 4: CABINET FLOADED 5: CABINET 0: NOT SELECTED 1: NONE or STAGES 2: CONTINUOS SLOW 3: CONTINUOS FAST 0: NOT SELECTED 1: PLATES 2: SHELL&TUBES 3: FINNED FAST 4: FINNED SLOW 0: NOT SELECTED 1: PLATES 2: SHELL&TUBES 3: FINNED FAST 4: FINNED SLOW Type R/W I R/W I R/W I R/W -2.0 °C -70.0 50.0 I R/W -18.0 °C -70.0 50.0 I R/W -3.0 °C -70.0 50.0 I R/W 12.0 °C -05.0 90.0 I R/W 12.0 °C -05.0 90.0 I R/W 15.0 °C -05.0 90.0 I R/W Upper SuperHeat Alarm Threshold in Auto 20.0 °C 0.0 99.9 I R Upper SuperHeat Alarm Threshold in Manual Percentage of maximum power managed by the valve in the circuit where it is installed (Chiller) (Auto) Percentage of maximum power managed by the valve in the circuit where it is installed (Chiller) (Manual) Proportional Factor of PID in Chiller (Auto) Proportional Factor of PID in Chiller (Manual) Integration Time for Superheating Control in Chiller (Auto) Integration Time for Superheating Control in Chiller (Manual) Percentage of maximum power managed by the valve in the circuit where it is installed (CP) (Auto) Percentage of maximum power managed by the valve in the circuit where it is installed (CP) (Manual) Proportional Factor of PID in CP (Auto) Proportional Factor of PID in CP (Manual) Integration Time for Superheating Control in CP (Auto) 0.0 °C 0.0 99.9 I R/W 0 % 0 999 I R 0 % 0 100 I R/W 0.0 0.0 ----- 0.0 0.0 99.9 99.9 I I R R/W 0 s 0 999 I R 0 s 0 999 I R/W 0 % 0 999 I R 0 % 0 100 I R/W 0.0 0.0 0 ----s 0.0 0.0 0 99.9 99.9 999 I I I R R/W R 0 s 0 999 I R/W 0 --- 0 999 I R Integration Time for Superheating Control in CP (Manual) DF-Circuit/EEV Ratio Auto Value description Percentage of maximum power managed by the valve in the circuit where it is installed (DF) (Auto) Percentage of maximum power managed by the valve in the circuit where it is installed (DF) (Manual) Proportional Factor of PID in DF (Auto) Proportional Factor of PID in DF (Manual) Integration Time for Superheating Control in DF (Auto) Integration Time for Superheating Control in DF (Manual) Dead Zone for PID Control (Auto) Dead Zone for PID Control (Manual) Derivative Time for PID (Auto) Derivative Time for PID (Manual) Integration Time for Low Superheating Control (Auto) Integration Time for Low Superheating Control (Manual) Integration Time for Low Evaporation Pressure Control (Auto) Integration Time for Low Evaporation Pressure Control (Manual) Integration Time for High Evaporation Pressure Control (Auto) Integration Time for High Evaporation Pressure Control (Manual) Duration of MOP Suspension (Auto) Duration of MOP Suspension (Manual) Attenuation Coefficient on Capacity Changes Time beyond which, under specific conditions, the valve is blocked (Auto) Time beyond which, under specific conditions, the valve is blocked (Manual) Maximum Condensation Temperature Value (Auto) Maximum Condensation Temperature Value (Manual) +030220741 Smart HP – rel. 1.0 - 05/09/2008 0 --- 0 100 I R/W 0.0 0.0 0 0 0.0 0.0 0.0 0.0 0.0 0.0 --------°C °C s s s s 0.0 0.0 0 0 0.0 0.0 0.0 0.0 0.0 0.0 99.9 99.9 999 999 9.9 9.9 99.9 99.9 99.9 30.0 I I I I I I I I I I R R/W R R/W R R/W R R/W R R/W 1.5 s 0.0 99.9 I R 0.0 s 0.0 25.5 I R/W 2.5 s 0.0 99.9 I R 0.0 s 0.0 25.5 I R/W 60 0 s s 0 0 999 999 I I R R/W 0 --- 0 1 D R/W 60 s 0 999 I R 0: NO 1: YES 0 s 0 999 I R/W 85.0 0.0 °C °C 0.0 0.0 99.9 99.9 I I R R/W 47 BMS addr. Mask Index Descr. display High Tcond.int.time Auto CH-SuperHeat set Auto Hdc09 CH-Low SuperHeat Auto HP-SuperHeat set Auto Hdc10 HP-Low SuperHeat Auto DF-SuperHeat set Auto Hdc11 He_01 He_02 DF-Low SuperHeat Auto Descr. Integration Time for Condensation Control (Auto) Integration Time for Condensation Control (Manual) Superheat Set Point in Chiller (Auto) Superheat Set Point in Chiller (Manual) Low Superheat Set Point in Chiller (Auto) Low Superheat Set Point in Chiller (Manual) Superheat Set Point in Heat Pump (Auto) Superheat Set Point in Heat Pump (Manual) Low Superheat Set Point in Heat Pump (Auto) Low Superheat Set Point in Heat Pump (Manual) Superheat Set Point in Defrost (Auto) Superheat Set Point in Defrost (Manual) Low Superheat Set Point in Defrost (Auto) Low Superheat Set Point in Defrost (Manual) Default/Password INSTALL DEFAULT Delete user settings Reset the CAREL Default Values (see list of Parameters) and enter global default values: Default/Password Enter new Select New Manufacturer Password password manufacturer(PW2): +030220741 Smart HP – rel. 1.0 - 05/09/2008 Def UOM Min Max 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 s s °C °C °C °C °C °C °C °C °C °C °C °C 0.0 0.0 -99.9 -99.9 -99.9 -04.0 -99.9 -99.9 -99.9 -04.0 -99.9 0.0 -99.9 -04.0 99.9 25.5 99.9 99.9 99.9 21.0 99.9 99.9 99.9 21.0 99.9 99.0 99.9 21.0 0 --- 0 1 1234 --- 0 9999 48 Value description 0: NO 1: YES Type R/W I I I I I I I I I I I I I I R R/W R R/W R R/W R R/W R R/W R R/W R R/W D R/W I R/W BMS addr. 8. VARIABLES SENT TO THE SUPERVISOR Smart HP can be connected to a number of supervision systems, especially those using the Carel and Modbus BMS communication protocols. The connection uses a BMS serial port. The different connection protocols are managed by the following optional boards: • Carel RS485: part no. PCOS004850 (see Fig. 8.a) • Modbus RS485: part no. PCOS004850 (see Fig. 8.a) • Lon Works FTT10: part no. PCO10000F0 (*) • Bacnet RS485:part no. PCO1000BA0 (*) • Bacnet Ethernet:part no. PCO1000WB0 (*) • Trend: part no. PCO100CLP0 (*) Note: (*) these communications protocols are not currently manageably with the Configuration Tools (LONset and BACset) available on the internet site http: // ksa . carel . com /; however, the Smart HP software is setup to use them. 3 The following figure represents the connection diagram for the serial BMS board with the pCO . Fig. 8.a The following table shows the variables sent to the supervisor. CAREL ModBus Mask index Descr. Address Address Analog 1 1 D__01 2 2 D__01 3 3 D__02 4 4 D__03 5 5 D__03 D__37 (EVD 400), D__07 (unit 3 or 4) D__37 (EVD 400), D__07 (unit 3 or 4) D__08 D__09 D__09 D__06 / D__08 6 6 7 7 9 10 11 9 10 11 12 12 13 13 B__01 14 14 B__01 15 15 B__02 16 16 B__02 17 17 Gfc43 18 18 Gfc43 19 19 Gfc43 +030220741 Smart HP – rel. 1.0 - 05/09/2008 Def. UOM Min Max R/W Name (*) 0.00 °C -99.9 -99.9 R Out_Geo 0.00 °C -99.9 -99.9 R In_Geo 0.00 °C -99.9 -99.9 R Sanitary_Temp 0.00 °C -99.9 -99.9 R Mix_Circ_Temp 0.00 °C -99.9 -99.9 R In_Plant Low Pressure Compressor(s) 0.00 --- -1 99.9 R Lp_Pressure High Pressure Compressor(s) 0.00 --- -1 99.9 R Hp_Pressure Solar Circuit Inlet Boiler Temperature Solar Panel 1 Temperature Solar Panel 2 Temperature Installation Circuit Heat Exchanger Water Outlet Temperature Comfort Room Temperature Set Point (Cooling) Comfort Room Temperature Set Point (Heating) Economy Room Temperature Set Point (Cooling) Economy Room Temperature Set Point (Heating) Maximum Room Temperature Limit (Cooling) Minimum Room Temperature Limit (Cooling) Maximum Room Temperature Limit 0.00 0.00 0.00 °C °C °C -99.9 -100 -100 99.9 200 200 R R R In_Solar_Boiler Solar_Circ1 Solar_Circ2 0.00 °C -99.9 99.9 R Out_Plant 23 °C -99.9 99.9 R/W Set_Temp_Comf_S 23 °C -99.9 99.9 R/W Set_Temp_Comf_W 27 °C -99.9 99.9 R/W Set_Temp_Econ_S 19 °C -99.9 99.9 R/W Set_Temp_Econ_W 35 °C -99.9 99.9 R/W Set_T_Lim_Hi_S 15 °C -99.9 99.9 R/W Set_T_Lim_Low_S 35 °C -99.9 99.9 R/W Set_T_Lim_Hi_W Geothermal Heat Exchanger Outlet Water Temperature (geothermal outlet B1) Geothermal Heat Exchanger Inlet Water Temperature (geothermal return circuit B2) Domestic Hot Water Temperature (B3) Mixing Circuit Outlet Water Temperature (b4) Primary Circuit Heat Exchanger Inlet Water Temperature (B5) 49 CAREL Address ModBus Address Mask index 20 20 Gfc43 21 21 B__02 22 22 B__02 23 23 B__01 24 24 B__01 25 26 27 28 29 25 26 27 28 29 Gfc44 Gfc44 Gfc44 Gfc44 Gc_01 30 30 Gc_02 31 31 Gc_02 32 32 Gfc34 33 33 Gfc34 35 D__05, Main page 35 36 36 Gc_04 37 37 Gc_04 38 38 Gc_05 39 39 Gc_05 40 41 40 41 Gc_04 Gc_05 50 50 Room:01 51 51 Room:01 52 52 Room:02 53 53 Room:02 54 54 Room:03 55 55 Room:03 56 56 Room:04 57 57 Room:04 58 58 Room:05 59 59 Room:05 60 60 Room:06 61 61 Room:06 62 63 64 65 66 67 68 69 70 71 72 73 62 63 64 65 66 67 68 69 70 71 72 73 Room:01 Room:01 Room:02 Room:02 Room:03 Room:03 Room:04 Room:04 Room:05 Room:05 Room:06 Room:06 74 74 D__40 Descr. (Heating) Minimum Room Temperature Limit (Heating) Economy Room Humidity Set Point (Heating) Economy Room Humidity Set Point (Cooling) Comfort Room Humidity Set Point (Heating) Comfort Room Humidity Set Point (Cooling) Room Humidity Minimum Limit (Cooling) Room Humidity Maximum Limit (Cooling) Room Humidity Minimum Limit (Heating) Room Humidity Maximum Limit (Heating) Storage recovery temperature set point Mixing Circuit Water Outlet Set Point (Cooling) Mixing Circuit Water Outlet Set Point (Heating) Mixing Circuit Water Outlet Temperature Minimum Limit Mixing Circuit Water Outlet Temperature Maximum Limit Outside Air Temperature Standard Condition Temperature Set (Chiller) Standard Condition Temperature Set (Heat Pump) Energy Savings Condition Temperature Set (Chiller) Energy Savings Condition Temperature Set (Heat Pump) Standard Condition ACS Temperature Set Energy Savings ACS Temperature Set Temperature Measured by SERIAL PROBE NO. 1 Humidity Measured by SERIAL PROBE NO. 1 Temperature Measured by SERIAL PROBE NO. 2 Humidity Measured by SERIAL PROBE NO. 2 Temperature Measured by SERIAL PROBE NO. 3 Humidity Measured by SERIAL PROBE NO. 3 Temperature Measured by SERIAL PROBE NO. 4 Humidity Measured by SERIAL PROBE NO. 4 Temperature Measured by SERIAL PROBE NO. 5 Humidity Measured by SERIAL PROBE NO. 5 Temperature Measured by SERIAL PROBE NO. 6 Humidity Measured by SERIAL PROBE NO. 6 Temperature Measured by CLIMA NO. 1 Humidity Measured by CLIMA NO. 1 Temperature Measured by CLIMA NO. 2 Humidity Measured by CLIMA NO. 2 Temperature Measured by CLIMA NO. 3 Humidity Measured by CLIMA NO. 3 Temperature Measured by CLIMA NO. 4 Humidity Measured by CLIMA NO. 4 Temperature Measured by CLIMA NO. 5 Humidity Measured by CLIMA NO. 5 Temperature Measured by CLIMA NO. 6 Humidity Measured by CLIMA NO. 6 Humidity Measured by OUTSIDE SERIAL PROBE NO. 7 Def. UOM Min Max R/W Name (*) 15 °C -99.9 99.9 R/W Set_T_Lim_Low_W 50 %rH 0 -100 R/W Set_Humid_Econ_W 50 %rH 0 -100 R/W Set_Humid_Econ_S 50 %rH 0 100 R/W Set_Humid_Comf_W 50 %rH 0 100 R/W Set_Humid_Comf_S 30 90 30 90 0.00 %rH %rH %rH %rH °C 0 0 0 0 0 100 100 100 100 30 R/W R/W R/W R/W R/W Set_H_Lim_Low_S Set_H_Lim_Hi_S Set_H_Lim_Low_W Set_H_Lim_Hi_W Setp_Temperature_Coll 0.00 °C -99.9 99.9 R/W Set_Man_Floor_Summer 0.00 °C -99.9 99.9 R/W Set_Man_Floor_Winter 0.00 °C 0 99.9 R/W Lim_Min_Outlet_Floor 0.00 °C 0 99.9 R/W Lim_Max_Outlet_Floor 0.00 °C -99.9 99.9 R External_Temp 23 °C 0 99.9 R/W Set_Temp_StdC_Ch 23 °C 0 99.9 R/W Set_Temp_StdC_Hp 27 °C 0 99.9 R/W Set_Temp_ES_Ch 19 °C 0 99.9 R/W Set_Temp_ES_Hp 23 23 °C °C 20 20 80 80 R/W R/W Set_HotWater_Std Set_HotWater_E_S 0.00 °C -99.9 99.9 R a_Temperature1 0.00 %rH 0 100 R a_Humidity1 0.00 °C -99.9 99.9 R a_Temperature2 0.00 %rH 0 100 R a_Humidity2 0.00 °C -99.9 99.9 R a_Temperature3 0.00 %rH 0 100 R a_Humidity3 0.00 °C -99.9 99.9 R a_Temperature4 0.00 %rH 0 100 R a_Humidity4 0.00 °C -99.9 99.9 R a_Temperature5 0.00 %rH 0 100 R a_Humidity5 0.00 °C -99.9 99.9 R a_Temperature6 0.00 %rH 0 100 R a_Humidity6 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 °C %rH °C %rH °C %rH °C %rH °C %rH °C %rH -99.9 0 -99.9 0 -99.9 0 -99.9 0 -99.9 0 -99.9 0 99.9 100 99.9 100 99.9 100 99.9 100 99.9 100 99.9 100 R R R R R R R R R R R R a_Temp_Cli1 a_Hum_Cli1 a_Temp_Cli2 a_Hum_Cli2 a_Temp_Cli3 a_Hum_Cli3 a_Temp_Cli4 a_Hum_Cli4 a_Temp_Cli5 a_Hum_Cli5 a_Temp_Cli6 a_Hum_Cli6 0.00 %rH 0 100 R a_HumidityExt Humidifier Analogue Output 0 --- 0 9999 R On_Humi_Mod_Device 3-way Installation Valve Analogue Output 0 --- 0 1000 R Out_EVMix_Mod 0 --- 0 9999 R Out_Pump_Mix_Mod 0 --- -9999 9999 R Ctrl_Mod_Geo_P 0 --- 0 3 R/W OnOff_Status Integer 1 209 2 210 3 211 4 212 5 213 On_Humi_Mo d_Device Out_EVMix_M od Out_Pump_Mi x_Mod Ctrl_Mod_Geo _P A__01 6 214 A__01 7 215 C__01 +030220741 Smart HP – rel. 1.0 - 05/09/2008 Modulating Domestic Pump Analogue Output Modulating Geothermal Pump Analogue Output Unit On-Off (0=Off; 1=On from room) (0=Off; 1=On; 2=Energy Savings; 3=Auto) (0=Domestic; 1=Heating + Domestic; 2=Cooling + Domestic) Current Date 50 0 --- 0 2 R/W S_W_Change_Type 0 --- 1 31 R Current_Day CAREL Address ModBus Address Mask index 8 9 10 11 12 216 217 218 219 220 C__01 C__01 C__01 C__01 C__01 1 2 3 4 5 6 7 1 2 3 4 5 6 7 Ha_01 Ha_02 Ha_03 Ha_04 Ha_05 Ha_06 8 8 9 9 11 11 12 12 13 13 14 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 15 16 17 18 19 20 21 22 23 24 25 26 27 28 31 31 32 32 33 33 34 34 35 35 36 36 37 37 38 38 39 39 40 40 41 41 42 42 43 43 44 44 45 45 46 46 47 48 47 48 49 49 50 51 50 51 52 52 53 53 54 54 55 55 56 56 57 57 Descr. Def. UOM Min Max R/W Name (*) Current Hour Current Minutes Month Day of the Week Year 0 0 0 1 0 ----------- 0 0 1 1 0 23 59 12 7 99 R R R R R Current_Hour Current_Minute Current_Month Current_Weekday Current_Year Request to Delete Alarm Memory Unit Type 1 Configuration Unit Type 2 Configuration Unit Type 3 Configuration Unit Type 4 Configuration Unit Type 5 Configuration Unit Type 6 Configuration Operating Mode (Chiller - Cooling/ Heat Pump - Heating) Domestic Activated 0 0 0 0 0 0 0 --------------- 0 0 0 0 0 0 0 1 1 1 1 1 1 1 R/W R R R R R R Reset_Alarm config_1 config_2 config_3 config_4 config_5 config_6 0 --- 0 1 R CH_HP_Mode 0 --- 0 1 R Sanitary Digital output 1 0 --- 0 1 R OUT1 Digital output 2 0 --- 0 1 R Out2 Digital output 3 0 --- 0 1 R OUT3 Digital output 4 0 --- 0 1 R OUT4 Digital output 5 Digital output 6 Digital output 7 Digital output 8 Digital output 9 Digital output 10 Digital output 11 Digital output 12 Digital output 13 Digital output 14 Digital output 15 Digital output 16 Digital output 17 Digital output 18 Geothermal Flow Switch Alarm (manual reset) Evaporator Flow Switch Alarm (manual reset) Compressor 1 Thermal Overload Switch Alarm Geothermal Circuit Pump Thermal Overload Switch Alarm Installation Pump Thermal Overload Switch Alarm Compressor 2 Thermal Overload Switch Alarm Domestic Pump Thermal Overload Switch Alarm Domestic Hot Water Storage Heater Thermal Overload Switch Alarm Mixing Circuit Pump Thermal Overload Switch Alarm Solar Circuit Pump 1 Thermal Overload Switch Alarm Solar Circuit Pump 2 Thermal Overload Switch Alarm Compressor 1 High Pressure Alarm Status from Digital Input Compressor(s) High Pressure Alarm Status from Transducer Compressor 2 High Pressure Alarm Status from Digital Input Compressor(s) Low Pressure Alarm from Digital Input Compressor(s) Low Pressure Alarm from Transducer Geothermal Antifreeze Alarm Primary Circuit Antifreeze Alarm Installation Integrated Furnace/Heater Thermal Overload Switch Alarm Humidifier Alarm Dehumidifier Alarm Installation Temperature Maximum Threshold Limit Reached Alarm Installation Temperature Minimum Threshold Limit Reached Alarm ACS Temperature Maximum Threshold Limit Reached Alarm ACS Temperature Maximum Threshold Limit Reached from Solar Circuit Alarm Humidity Minimum Threshold Limit Reached Alarm Humidity Maximum Threshold Limit Reached Alarm 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ----------------------------- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R R R R R R R R R R R R R R OUT5 OUT6 OUT7 OUT8 OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 OUT15 OUT16 OUT17 OUT18 Digital D__17 / D__18 D__17 / D__18 D__17 / D__18 D__17 / D__18 D__19 D__19 D__19 D__19 D__20 D__20 D__20 D__20 D__20 D__21 D__21 D__21 +030220741 Smart HP – rel. 1.0 - 05/09/2008 51 0 --- 0 1 R Geo_Flow_Alarm 0 --- 0 1 R Evap_Flow_Alarm 0 --- 0 1 R Comp1_Ovl_Alarm 0 --- 0 1 R Geo_Pump_Ovl_Al 0 --- 0 1 R User_Pump_Ovl_Al 0 --- 0 1 R Comp2_Ovl_Alarm 0 --- 0 1 R Sanitary_Pump_Ovl_Al 0 --- 0 1 R Heat_Boiler_Alarm 0 --- 0 1 R Mix_Pump_Alarm 0 --- 0 1 R SolarPump1_Ov 0 --- 0 1 R SolarPump2_Ov 0 --- 0 1 R Al_HP1_Din 0 --- 0 1 R Al_HP1_Tran 0 --- 0 1 R Al_HP2_Din 0 --- 0 1 R Al_LP_Din 0 --- 0 1 R Al_LP_Tran 0 0 ----- 0 0 1 1 R R Al_Antif_Geo Al_Antif_Plant 0 --- 0 1 R Boiler_Ov 0 0 ----- 0 0 1 1 R R Humidifier_Alarm Dehumidifier_Alarm 0 --- 0 1 R Aut_Man_Al_Limit_MaxT_Floor 0 --- 0 1 R Aut_Man_Al_Limit_MinT_Floor 0 --- 0 1 R Aut_Man_Al_Overtemp_Boiler 0 --- 0 1 R Aut_Man_Al_Solar_Temp 0 --- 0 1 R Aut_Man_Al_Limit_Low_Humidity 0 --- 0 1 R Aut_Man_Al_Limit_High_Humidity Note: the addressed provided in the table are according to the CAREL standard. The second column provides the ModBus (packet) address. If using a ModBus communication protocol in "register" mode, the addresses listed in the table (ModBus column) must be increased by one, both for the digital variables (coil) and for the analogue variables (register). Note: (*) “Name” indicates the name of the variable used internally by the commissioning program. +030220741 Smart HP – rel. 1.0 - 05/09/2008 52 9. ALARMS 9.1 Alarm Management When alarm is activated, the Smart HP performs a few actions on the installation or unit, a message appears on the display, the respective LEDs turn on, and the alarm relay is activated. Alarms can be divided into three categories: severe unit alarms (the unit or fundamental components of the unit are stopped), alarms that stop only one or more system operations, other alarms (only messages or warnings) that do not stop any operations rather they advise the user, for example, that thresholds have been exceeded. There are also alarms that do not originate from the pCO control board rather from the components connected to it, such as the DP probes, Clima or EVD400 (these may be due to communication problems between these components and the controller or real malfunctions between these accessories).. At the bottom of the Alarm Table (section 9.3) is the key for the alarm messages-codes. They allow you to identify where the alarm indicated by the Smart HP was generated. To monitor the active alarm, you only need to push the through the list, use the and key and the name (or names if there are more than one active alarms) will appear on the display. To scroll keys. To reset the active alarms, you must first view them and then press then The following figure illustrates the screen that appears when the again. If the alarm condition no longer exists, the alarm will be reset; if not it will reappear. key is pressed. You can see: 1) the origin of the alarm and 2) the part of the installation/unit involved. Fig. 9.a Note: if the alarm is reset automatically, the system will return to normal operation, but the alarm LED and relative message string will remain active until the is pressed at least twice. key 9.2 Alarm Log From the main menu, you can enter the dedicated branch (E.), from which you can access the alarm log display screen. Fig. 9.b The information provided in these screens involve: 1. The chronological number of the even (which indicates the exact moment that the alarm was triggered, or its "age"; E__01 indicates the oldest alarm) 2. The time and date of the alarm 3. The alarm code (please see sec. 9.3) 4. A short description of the logged alarms 5. The values relative to inlet and outlet temperature and pressure Note: The maximum number of alarms logged is 50. When this limit is exceeded, the new events overwrite the old ones, which are thereby deleted. The logged alarms are those shown in the table (sec. 9.3) that have an asterisk (*) next to the code. These are alarms that regard the correct operation of the unit, which are thus the most important ones. The alarms relative to the installation system are not recorded. Historic Log It is possible to record the events on the expanded 2 MB memory connected permanently to the board. To download the data recorded in the historic log, you must use the Winload tool. In any case, please refer to the manual dedicated to the pCO system (+030220335). 9.3 Alarm Table Code Descr. display ALA01 * ALA02 * ALA03 * ALA04 * Position: B1 Probe B1 faulty or disconnected alarm Position: B2 Probe B2 faulty or disconnected alarm Position: B3 Probe B3 faulty or disconnected alarm Position: B4 Probe B4 faulty or disconnected alarm +030220741 Smart HP – rel. 1.0 - 05/09/2008 Reset Delay Alarm Relay Notes Automatic 60 sec YES Stop the unit Automatic 60 sec YES If the modulating geothermal pump is regulated to maximum speed. Automatic 60 sec YES Stop control of the domestic water circuit Automatic 60 sec YES Stop control of the mixing circuit (except type 5) 53 Code Descr. display ALA05 * ALA06 * ALA07 * ALA08 * ALA09 * ALA10 * Position: B5 Probe B5 faulty or disconnected alarm Position: B6 Probe B6 faulty or disconnected alarm Position: B7 Probe B7 faulty or disconnected alarm Position: B8 Probe B8 faulty or disconnected alarm Position: B9 Probe B9 faulty or disconnected alarm Position: B10 Probe B10 faulty or disconnected alarm Reset Delay Alarm Relay Automatic 60 sec YES Stop the unit Automatic 60 sec YES Block the probe's enabled functions (except type 4) Automatic 60 sec YES If the pressure probe stops the unit Automatic 60 sec YES If the pressure probe stops the unit, if the mixing circuit outlet probe stops control, of if the probe in the lower portion of the domestic water tank stops control of the solar panel circuits. Automatic 60 sec YES Stop solar pump 1 operation Automatic 60 sec YES Stop solar pump 2 operation ALB01 * Position: ID3 High pressure compressor 1 Manual Immediately YES ALB02 * Position: ID4 Low pressure compressor/compressors From parameter (Hc_05) From parameter (Hc_03; Hc_04) YES ALB03 * Position: ID10 High pressure compressor 2 ALD12 ALD13 Position: B7/S2 High pressure compressor 1 by transducer Position: B8/S1 Low pressure compressor/compressors by transducer Position: ID2 Compressor 1 overload Position: ID9 Compressor 2 overload Driver Eeprom error Driver MOP timeout (check timeout) Driver Timeout LOP (check timeout) Driver Low SuperHeat (check timeout) Driver High SuperHeat (check timeout) Driver EEV not closed during power OFF Driver Probe S1 error Driver Probe S2 error Driver Probe S3 error Driver EVD GoAhead request (maintenance menu) Driver Lan disconnected Driver Auto Setup Procedure not completed ALP01 * Position: ID1 Water flow switch geothermal side ALB04 * ALB05 * ALC01 * ALC02 * ALD01 ALD03 ALD04 ALD05 ALD06 ALD07 ALD08 ALD09 ALD10 ALD11 manual immediately YES Manual Immediately YES From parameter (Hc_05) Manual Manual Manual Manual Manual Manual Manual Manual Manual Manual Manual From parameter (Hc_03; Hc_04) Immediately Immediately Immediately Immediately Immediately Immediately Immediately Immediately Immediately Immediately Immediately Immediately YES 30 sec Immediately From parameter (Hc_18; Hc_19) YES YES manual immediately YES ALP05 * Position: ID12 Water flow switch system side ALP06 Position: ID15 Pump mix circuit overload Manual From parameter (Hc_17) Manual ALP07 Position: ID17 Pump solar circuit 1 overload Manual Immediately ALP08 Position: ID18 Pump solar circuit 2 overload Manual Immediately ALR01 Position: ID7 Alarm boiler/heater integr. plant Automatic Immediately ALR02 Position: ID13 Humidifier alarm from digital input Automatic Immediately ALR03 Position: ID6 Boiler heater DHW overload from digital input (unit 1; 2) Manual Immediately ALR03 Position: ID14 Boiler heater DHW overload from digital input (unit 3; 4; 5;6) Manual Immediately ALR04 Position: ID16 Dehumidifier alarm from digital input Automatic Immediately ALS01 Serial probe n° 01 Humidity probe broken Automatic 60 sec ALS02 Serial probe n° 01 Probe Offline Automatic 60 sec ALS03 Serial probe n° 01 Temperature probe broken Automatic 60 sec ALS04 Serial probe n° 02 Humidity probe broken Automatic 60 sec ALS05 Serial probe n° 02 Probe Offline Automatic 60 sec ALS06 Serial probe n° 02 Temperature probe broken Automatic 60 sec ALS07 Serial probe n° 03 Humidity probe broken Automatic 60 sec ALP03 * +030220741 Smart HP – rel. 1.0 - 05/09/2008 YES YES YES YES YES YES YES YES YES YES YES Manual ALP04 * ALP02 * YES Manual Manual From parameter (Hc_20) Position: ID5 Pumps overload unit/plant (unit 1; 2) Position: ID5 Goethermal system pump overload (unit 3; 4; 5; 6) Position: ID6 System pump overload (or mix pump overload) Position: ID11 DHW pump overload ALP02 * Notes YES manual immediately YES manual immediately YES Immediately From parameter (Hc_15; Hc_16) Immediately YES YES YES Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be 54 Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the relative compressor. The unit is blocked if it is the only active compressor. Stop the relative compressor. The unit is blocked if it is the only active compressor. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on only on the Type 6 unit. Stop the domestic water circuit and the recovery logic. Stop the compressor(s), the geothermal pump, the primary circuit, the mixing circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the mixing circuit pump and shut the 3-way valve Stop solar pump 1 operation Stop solar pump 2 operation Block the relative integration system Stop operation of the modulating humidifier Block the relative integration system Block the relative integration system Stop operation of the dehumidifier The last zone probe to go in alarm turns off the pump and shuts the valve. Alarm signal on the dedicated screen. Code Descr. display Reset Delay ALS08 Serial probe n° 03 Probe Offline Automatic 60 sec ALS09 Serial probe n° 03 Temperature probe broken Automatic 60 sec ALS10 Serial probe n° 04 Humidity probe broken Automatic 60 sec ALS11 Serial probe n° 04 Probe Offline Automatic 60 sec ALS12 Serial probe n° 04 Temperature probe broken Automatic 60 sec ALS13 Serial probe n° 05 Humidity probe broken Automatic 60 sec ALS14 Serial probe n° 05 Probe Offline Automatic 60 sec ALS15 Serial probe n° 05 Temperature probe broken Automatic 60 sec ALS16 Serial probe n° 06 Humidity probe broken Automatic 60 sec ALS17 Serial probe n° 06 Probe Offline Automatic 60 sec ALS18 Serial probe n° 06 Temperature probe broken Automatic 60 sec ALS19 External serial probe Humidity probe broken Automatic 60 sec ALS20 External serial probe Probe Offline Automatic 60 sec ALS21 External serial probe Temperature probe broken Automatic 60 sec ALT01 threshold reached comp. 1 op. hour Manual Immediately ALT02 threshold reached comp. 2 op. hour Manual Immediately ALT03 Operating hour threshold reached geothermal pump Manual Immediately ALT04 Operating hour threshold reached primary pump Manual Immediately ALT05 Operating hour threshold reached DHW pump Manual Immediately ALT06 Operating hour threshold reached mix pump Manual Immediately ALT07 Operating hour threshold reached solar pump 1 Manual Immediately ALT08 Operating hour threshold reached solar pump 2 Manual Immediately ALU01 * Geothermal exchanger antifreeze ALU02 * System exchanger antifreeze ALW01 Parameter config. Error Request enable time bands From parameter (Gfc36) From parameter (Gfc38) Automatic Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Immediately YES Immediately YES Immediately ALW02 Reach threshold temp. max mix circuit Automatic 60 sec ALW03 Reach threshold temp. min mix circuit Automatic 60 sec ALW04 Reach threshold high temperature sanitary Automatic 60 sec ALW05 Reach threshold max temperature sanitary to solar collector Automatic 60 sec ALW06 Reach threshold max humidity raised Automatic 90 sec +030220741 Smart HP – rel. 1.0 - 05/09/2008 Alarm Relay Notes Block the probe's enabled functions Warning signal Warning signal Warning signal Warning signal Warning signal Warning signal Warning signal Warning signal Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Stop the compressor(s), the geothermal pump, the primary circuit, and the domestic water circuit. The mixing circuit pump remains on. Warning signal Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) 55 Warning signal Warning signal Warning signal (Gfc23) Warning signal (Gfc23; Gfc01)) Warning signal Code ALW07 ALY01 ALY02 ALY03 ALY04 ALY05 ALY06 ALY07 ALY08 ALY09 ALY10 ALY11 ALY12 A. B. C. D. E. F. G. H. I M O P Q R S T U V W X Y Descr. display Reach threshold min humidity raised Clima Room: 01 Address: xxx Inside probe broken Clima Room: 01 Address: xxx Comunication error Clima Room: 02 Address: xxx Inside probe broken Clima Room: 02 Address: xxx Comunication error Clima Room: 03 Address: xxx Inside probe broken Clima Room: 03 Address: xxx Comunication error Clima Room: 04 Address: xxx Inside probe broken Clima Room: 04 Address: xxx Comunication error Clima Room: 05 Address: xxx Inside probe broken Clima Room: 05 Address: xxx Comunication error Clima Room: 06 Address: xxx Inside probe broken Clima Room: 06 Address: xxx Comunication error Reset Delay Automatic 90 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Automatic 60 sec Alarm Relay Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Can Be Enabled (Gfc49) Notes Warning signal The last zone CLIMA to go in alarm turns off the pump and shuts the valve. Alarm signal on the dedicated screen. Note: the last letter of the alarm code-label (the one before the numbers) has the following meaning: “AIN” pCO physical probe fault “Boh” Alarms that block the Circuit, High-Low pressure “Compressor” Thermal overload switches, covering “Driver” Electronic valve “Expansion” pCOe Alarms “Fan” “Generic” general alarms, faulty clock, HW, or Memory “Humidifier” “Fan Coil” alarms from a hydronic network “MP-BUS” / Belimo “Offline” Offline supervisor, offline pLAN “Pumps” Pump flow switches, pump thermal overload switches “Quality” HACCP, Consumption “Remote” Various alarms from digital inputs Serial probe” “Timing” Maintenance warning “unit” Alarms that block the unit “VFD” Inverter alarms from field “Warning” generic Defrost Clima Note: Alarm reset can be either manual, automatic or selectable by parameter. In the first case, the user must manually reset the alarm. In the second case, the alarm is automatically reset by the Smart HP, which logs the event in any case (these are alarms that are not grave and not potentially dangerous). In the last case the alarm is reset by a parameter. If this option is activated, the system will try to reset the alarm five times (at constant 10 second intervals, recorded in the alarm log). If after these five attempts the alarm continues to exist, Smart HP shifts to the manual reset mode, and the alarm relay is activated. If within the five consecutive attempts, the alarm/fault situation is resolved, the alarm relay is reset and logged. Note: the delays for the various alarms can be set, reset using the relative parameter (indicated between parenthesis) or not present (the message "immediate" indicates that there is no delay between when the fault/problem is detected by the Smart HP and the signal to the connected alarm). Note: the column for the "alarm relays" may contain the message "Yes" if the relay is activated, or "enabled" if it is can be activated or not using the relative parameter (in the screen Gfc49). The eventual enabling of a parameter by the alarm relay implies the contemporary activation in a single block of all alarms that are distinguished with the message "Can Be Enabled" in the above listed parameter table. CAREL reserves the right to make any modifications or changes to its product without any prior notice. +030220741 Smart HP – rel. 1.0 - 05/09/2008 56 NOTES___________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ +030220741 Smart HP – rel. 1.0 - 05/09/2008 57 ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ +030220741 Smart HP – rel. 1.0 - 05/09/2008 58 +030220741 Smart HP – rel. 1.0 - 05/09/2008 59 +030220741 Smart HP – rel. 1.0 - 05/09/2008 +030220741 Smart HP – rel. 1.0 - 05/09/2008 60