Download models 33R, 33E - The Wheel Horse Manual and Documentation
Transcript
w models w 33R, 33E • • • .M w ! Riding Rotary Mower • • • • • • • • • • • WITH PARTS LIST m WHEEL-HORSE PRODUCTS, INC. • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • o .c SERVICE MANUAL ! se or H el he yW OPERATION AND • • • • • • • • • • • SOUTH BEND, IND. A SSEMB LY A . Remove aI I parts from box and place i n a convenient arrange ment on a clean, level surface. B. Insert a Woodruff key, Part No. 1008, in the keyway in each rear axle. Assemble rear wheels on axles with nut for set screw to the inside making sure that the wheel hub does not touch the end of the axle housing. The wheels are held in place with set screws which must be tightened securely and locked with the jam nuts provided. w C. Slide the front wheels onto the front spindles and secure with washers, Part No. 1278, and snap rings, Part No. 1127. w D. Place steering wheel on steering column shaft and secure with the 3(6 x I % roll pin, Part No. 1227. E. Remove screws, holding seatspring in place, and reinstall with hitch bar in place on top of seat spring. w F. Attach fenders to tool box using holes that give proper location of fender with respect to wheels. G. Secure seat to top of seat spring with carriage bolt provided. The seat may be attached to either of the two holes in the seat spring depending on operator preference. .M H. Screw 5Yz" long pipe nipple into elbow in exhaust port in engine and screW muffler onto nipple. Tighten securely. I. Attach the two 6" wheels to the mower housing using shoulder bolt, Part No. 4177. Wheels can be moved up or down to obtain cutting heights of Yz" to 2Yz". In the up position mower cuts a full 3Yz" high. yW J. Assemble idler pulley, Part No. 1623. and shield assembly, Part No. 4931, to mower clutch pedal. The leaf spring on the shield assembly must be deflected down sO that it fits under the tubular portion of the clutch pedal assembly. The idler bushing Part No. 1536 must be placed between the idler and shield. Note! The belt must be in the idler pulley groove before these parts are a ssembled. Remove oil filler plug. located at the left rear side of the trans mission, and fill to level of hole with a good grade of S.A.E. 90 Gear Lube (will require about 3 pintsJ. The transmission should be checked after every 40 hours of use. The transmission should be drained once a year by removing plug on bottom to drain oil. Ref, II as above paragraph. This is a regular automotive type transmission with sliding gears and should have the same care as your car. B A TTE RY The battery installed in the Model BE is a dry charged battery. It is important that you properly prepare this battery to insure good service and long life. 1. Remove vent caps. Remove or destroy any sealing device which may have been used to close or restrict the vent openings. 2. Fill each cell of the battery to the proper level with the bat tery electrolyte. NOTE: Temperature of battery and electrolyte at time of filling should be above 60"F. Never fill battery in the vehicle. 3. BOOST CHARGE: 15 amps. for 10 minutes or 7 amps. for 30 minutes. Adjust electrolyte level, if necessary, after charge. 4. Install battery with battery posts toward the rear of mower. Start motor. Check to see if generator is charging properly. After battery has been in service, add only approved water. DO NOT ADD ACID. TIRE S The front tires are 3.50 x 4 pneumatic and should be filled to 2 0 pounds o f air pressure. T h e rear tires are 4.00 x 8 and should have 6 to 8 pounds of air pressure. STARTING ENGINE he K. Slide mower under unit and attach the four links using the fourth and sixth holes from the front on each side of the frame. Use % x I bolts, Part No. 1425, spacers, Part No. 4937, washers, Part No. 1434, and nuts, Part No. 1408, for attaching links to frame. A light machine oil should be used on all moving parts to keep joints from wearing and squeaking. L. Move lift lever forward and hook lift link to pin in lift arm, securing with washer and hair pin cotter. 2. Place gear shift lever in neutral position, lower the rotary mower to the ground on its gage wheels, make certain that the mower clutch is latched in the disengaged position. 3. Pull throttle lever Yz way out and turn to the right to lock it in position. Note: The Throttle control has a locking device. Turn the throttle control to the left to unlock, adjust to the desired position and turn to the right to lock. el M. With mower clutch in disengaged. down position, slide belt over engine pulley and place in outside groove. Release mower clutch and check belt alignment. Tightness of belt is automatically adjusted through the tension springs. 1. Before starting the engine open valve on sediment bowl. (NOTE: Auxiliary foot rest CAN NOT be used when mowing) 4. Pull choke lever all the way out to choke engine. If engine is warm and has been running, choking will not be necessary. H N. Adjust position of belt stop Part No. 4930, so that it just clears the outside of the belt when the mower is at maximum and mini mum height and with the belt clutch engaged. This insures proper release of mower clutch. 5. A. Model 33R has a recoil starter with an OFF and ON switch. To start push switch to ON position and pull recoil starter. (NOTE: ALL YOUR WARRANTY CLAIMS, AUTHORIZED NOTE: WORK, SHIPMEN1'S, WHEEL HORSE; MUS1' BE HANDLED THROUGH DEALER. 90 Day Warranty for Commercial Use. BE FORE YOU START There is NO OIL in the crankcase of the engine when shipped from the factory. Read Engine Manual and follow all instructions per taining to type of lubrication specified. The engine is the heart of your Lawn Ranger and it is very important that you keep it in good condition. Before mowing, the moWer should be operated at a slow speed to check all moving parts for any damage or looseness caused in transporting. Lubricate all grease fittings with a regular pressure gun lubricant every eight to ten hours of operation. Refer to Figure I for the location of grease fittings. 7. Depress clutch pedal on left side of the Lawn Ranger before selecting desired gear ra nge. 8. When starting the Lawn Ranger in winter it is desirable to de· press clutch so starter does not have to turn transmission. CLUTCHING om .c The engine and battery carry a separate warranty by the manufacturer. FOR ENGINE OR BATTERY SERVICE, CONTACT YOUR LOCAL ENGINE OR BATTERY SERVICE HEADQUARTERS. 6. When engine starts push choke in to off position and regulate throttle control by turning to the left to unlock and push in or out to desired speed. se WE warrant WHEEL HORSE PRODUCTS for ONE YEAR from date of purchase against defective parts and workmanship. We will replace, free of charge, any defective part if returned to the factory PREPAID". Wheel Horse Products, Inc., reserves the right to make changes or improvements upon its products with out imposing any obligations upon itself to install the same upon its products that have been previously manufactured. Keep feet clear of mower while pulling recoil starter.) B. Model 33E has an OFF and ON key. also a starter button. Turn key to ON position and push starter button. or W A RR AN T Y There is no need to force the gear shift lever if the gears do not immediately mesh. Depress clutch pedal all the way down and let up, then depress again and shift. To avoid sudden starts, release clutch pedal slowly. While in motion do not shift gears without depressing clutch pedal. The clutch pedal also operates the brakes WHEN DEPRESSED ALL THE WAY DOWN. For this reason, you should depress the clutch pedal ONLY % OF THE WAY DOWN WHEN SHIFTING while in motion. This clutch-brake pedal combination makes clutching automatic as you apply the brakes to stop. PARKING B RA KE The parking brake is located on the left side of the Lawn Ranger as shown in Figure I. To set the parking brake depress the clutch brake pedal as far as possible and push the parking brake for ward. To release the brake depress the clutch-brake pedal and pull the parking brake back. C ARE OF THE LAWN RA NGER 1. Keep the Lawn Ranger greased and oiled regularly. Refer to to Figure I for the location of grease fittings. Check transmission and engine case oil levels. 2. Keep engine air cleaner clean. 3. Keep tires properly inflated. This will add to engine life. See previous instructions. 4. Keep the Lawn Ranger covered and in a dry place when not in use .. w 5. Keep grass and dirt out of engine cowling as these will stop the flow of air and decrease engine life. w 6. BRAKE ADJUSTMENT. The brake band, located on the left side of the transmission, bra kes the transmission and in turn stops the wheels. Adjust the nut on the bra ke rod so that, when you depress the clutch pedal all the way down. the band tightens around the brake drum. just as the idler pulley releases the belt. Keep brake band and drum free from oil and dirt. w 7. Clutch.Brake Pedal Ad'justment. The clutch-brake pedal rod may be turned in or out to adjust the pedal to operator's desired position. Remove pin from rod and turn rod in or out for adjustment. .M S. When blades become dull, remove and regrind. CAUTION: Sharpen evenly on both sides so blade does not become out of balance. 9. On the Model BE ,check battery after every 40 hours of use. If the mower has been in storage it may be necessary to recharge. 10. Your Lawn Ranger is only as good as the service you give it. See your Wheel Horse Dealer for a thorough check-up after each season of use. 6. Never leave motor running unattended. in use - children could get hurt. heavy grass or weeds. The sideplates may be reinstalled in an in verted position, as shown by the dotted illustration, thus acting as an additional foot guard. EXTREME CAUTION should be exercised when the sideplates are removed, because of the danger of flying debris. 9. Exercise special care when mowing around objects to prevent the blades from striking them, and never deliberately mOw over any object. 10. Stop operation when another person approaches - prohibit others from riding with you on your riding mower. 1 1. Riding mowers can be tipped to either back or side. Exercise extreme ca ution when mowing on slopes or inclines. Engage clutch slowly and smoothly. Never abuse your mower by improper handling. 12. Never adjust mower or tractor until engine has been turned off. 13. If your Lawn Ranger is to be used for purposes other than mowing, latch mOWer clutch in disengaged position, stop engine and remove mower drive belt from engine pulley. The spring wire belt stop may be deflected to remove belt. Never allow children to operate unless you have removed this belt to prevent their accidentally engaging mower. (NOTE: Auxiliary Foot Rest for use only when mower Is removed. This foot rest CAN NOT be used when mowing.) :--'PAIIKI�IG BRAKE O PERATI ON WHEEL HORSE LAWN RA NGER SPECIFIC A TIONS With proper care and adjustment. your new Wheel Horse Lawn Ranger has been designed to give. many years of satisfactory performance. Preparation for operation and operating hints listed below are recommended for all mowers and approved by the Outdoor Power Institute for safe operation of your mower. 1. Before starting operation, clear the entire lawn area of all debris that could catch on to or be thrown by the blades. 2. When you mow on rough terrain or in high grass or weeds. the blade should be set at the highest cutting point. In tall grass or weeds. a second cutting may be made to bring the grass down to the d esired height. 3. Mowers do not operate as well in wet grass. Wet grass has a tendency to build up on mower housing and give non-uniform dis charge. (SPECIfICATIONS SUBJlfCT T O CHANGIf WITHOUT NOTICIf! 4. Fill gas tank outdoors. Avoid spilling gasoline and don't fill the tank while engine is running or while you are smoking. om .c "'--' se or H el Figure 1 Remove key when not 7. Don't overspeed the engine. Excessive cutting speed or tamper· ing with the governor can 'be dangerous. S. The �ower has side plates which may be removed when cutting he yW 1 1. When replacing belts be sure to purchase them from your Wheel Horse Dealer, as these belts are specifically designed for each application. (NOTE: Make sure all pulleys are in line.) 5. While mowing. give undivided attention to the job at hand, keep the cutting path in area of operation' clear of all persons, particu larly small childreno ,. .... . . . . . .. . . . . . . . . . . . 54 inches 41X inches Width Overall (with mower) . . ...... . o. 33)1 inches Width Overall (without mower) ', 26% inches Width at Front Wheels, 24% inches Height 33)1 inches Height to Top of Hood 28% inches Net Weight (33E) " 365 Ibs. Nef Weight (33R) . . . .. 339 Ibs. Frame Clearance . . 10% inches 6 HoP. Engine (4 cycle, single cylinder, air cooled) . . . .... . .. . Fuel Capacity , 4 quarts Tires (front) ............ ..... .. .3.50 x 4 Pneumatic (10" wheel d'a.) Tires (rear) ....... ... ..... . 4 .00 x 8 Pneumatic (16" wheel dia.) Length Overall Wheelbase . . . . . . . . . . . . . . . . . . . . • • • • • • • • • • • , 0 • 0 • • • • • • • ' • . . . . . . . . . . . . 0 0 • . . . . 0 0 • • • 0 0 • • • • • • 0 0 • • • • • • • • • . 0 • . 0 0 . 0 0 0 0 0 0 • • 0 • • 0 • • • 0 • • • • • • • 0 • • • • • 0 • • • • • • • 0 0 0 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 0 • • • • • • • • • • 0 • 0 0 • • • • • • • • • • • • • • • • • • • • • • • • 0 • • • • • • • • • • • 0 • • • • • • • • • • 0 • • • • • • • • 0 • 0 • • • • 0 0 0 • 0 • • 0 • • • 0 0 • • • • • • • • 0 0 • • • • • • 0 0 • • • • • • • • • • • • • • 0 • • • • • • • • • • • • • • • • • • 0 0 • • • • . • • • • . • • • • • • • • • 0 • • • • • 0 • • 0 • • • 0 • • • 0 • • • • • , 0 • • • • • • • • • Main Frame Ass'y. .M w w w • Wheel Ass'y. m o .c se or & H el he yW Steermg / I \ w / 1'1/ Ii I //-� � .M w w Wiring for 33E Lift & or H el T"ECUMS£H e H.P. ENGINE he yW 1 Brake Ass'y. m o .c se w yW .M w w (D I he Transmission el PARTS LIST for MODELS 33R and 33E RIDING ROTARY MOWER Ref. No. Part No. 1232 1372 1239 1242 1244 1262 1434 1273 1277 4912 1287 1303 1 1 5 3 1 2 2 6 5 1 1 3 2 3 1 1 1 1 1 2 3 1 1 1 2 4 1 2 2 1 1 2 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Part No. 1329 1331 1339 1340 1345 1346 1349 1350 1363 1364 1384 1385 1483 4944 4930 4452 1406 1316 1408 1410 1413 1416 1417 1418 1423 1424 1425 1426 1427 1428 1480 1430 1432 Name Qu ant ity �6-18 x 3X Hex Hd. Cap Screw �6 Shakeproof Washer %-16 x 3X Hex Hd. Cap Screw X x lX Roll Pin X-20 x 'K6 Thumb Screw X-20 x 17\', Thumb Screw X x X x lX Key Ya x 1X Roll Pin %-16 x % Hex Hd. Cap Screw �6 Round Nut % Std. Pipe Plug X -20 x !1 Keps Screw Decal Plug-Wheel Belt Stop Gasket-Tank X-20 Hex Nylock Nut �6-18 Hex lock Nut %-16 Hex Nylack Nut !1-13 Hex Nylock Nut %-24 Hex Nylock Nut X Split lock Washer �6 Split lock Washer % Split lock Wa.her %-16 x % Hex Hd. Cop Screw !1.13 Hex Jam Nut %.16 x 1 Hex Hd. Cap Screw %-16 x 1X x Hex Hd. Cap Screw %-16 x 2 Hex Hd. Cop Screw X-20 x % Hex Hd. Cap Screw #8 x % Tapping Screw X-13 x lX Carriage Hd. Bolt �,-24 x !1 Rd. Hd. Mach. Screw 4 2 1 5 2 1 .1 1 1 2 1 4 1 2 1 om .c 23 24 25 26 27 28 29 30 31 32 33 34 Handle Grip Knob Ya x 1 Cotter Key No. 15 Woodruff Key X Std. Pipe Plug Ten.ion Spring Square Head Set Screw Grea.e Fitting %·16 x 2 Hex Hd. Cap Screw �6·18 x �6 Socket Hd. Set Screw X·20 x X Socket Hd. Set Screw X x 1!1 Rotl Pin % 1.0. Shaft Cotlar No. 9 Woodruff Key % 1.0. Snap Riltg 1 1.0. Snap Ring �6 x 1!1 Roll Pin 7\'6 x 1!1 Roll Pin Ya Pipe Nip %.16 x lX Sq. Hd. Cup Point Set Screw Oil Seal Hoi r Pi n Cotter X·20 x % Dog Point Set Screw �1 x 'K6 Roll Pin Ya x 1 Roll Pin X -20 x % Rd. Hd. Mach. Screw % SAE Washer 10-32 x % Mach. Screw Wire Clip Tube & Nut Au'y. !1-13 x 2% Hex Hd. Cap Screw Oil Seal Ref. No. se 1000 1001 1002 1008 1013 1014 1023 1030 1032 1042 1066 1081 1085 1122 1127 1128 1136 1135 1192 1206 Quantity or 1 2 3 4 5 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 Name H When ordering parts alway. list Part No. and name of part. 1 4 4 21 1 1 4 2 4 8 3 2 6 1 6 15 1 2 PARTS LIST for MODELS 33R and 33E RIDING ROTARY MOWER When ordering parts always list Part No. and name of part. ���-.-�-. . ��- . Ref. N0' 1 Part No. ��- . ������- .. ��-.... Name .... �� .�--.�.. Ref. +-- -�- ._- No. -···· Part +-- No. --�···--�- I- Name Quantity --�-- . _-- . --. -...---+... -.-� 2 141 3917 Bevel Pinion 3918 Steeting Pivot 1 3919 Steering Arm 2 1 Needle Bearing 2 71 1516 Bushing 1 142 143 72 1518 Needle Bearing 1 144 2297 Brace 73 74 75 1528 1529 Needle Bearing 2 Needle Bearing 2 Needle Bearing 1 1240 3935 3940 U·Bolt 1530 1531 145 147 149 Needle Bearing 1 150 Tool Box 1532 Needle Bearing 151 Ball Bearing 152 3945 Upper Steering Shaft 1 79 1533 1536 1 2 3587 3944 Idler Bushing 1 3949 Clevis Pin 81 82 1576 1611 "V" Belt 70" A Section 2 1 1621 1623 Engine Pulley 1 Idler Pulley 1 3950 3973 3978 3979 Idler Arm Pulley 1 1 154 155 1664 Rear Wheel Ass'y. 3586 3080 Front Wheel Ass'y. 2 2 1739 Tecumseh Muflle r 3585 4910 Upper Plunger Rod 1745 1751 Ammeter Reverse Idler Gear w 1508 83 84 85 87 88 90 91 93 .M w w 77 78 Starter Button 156 157 158 159 160 "xhaust Brake Rod Drag Link Lower 1 Steering Shaft 1 Seat Seat Cushion 1 1 Pivot Brake 1 Fender R.H. 1 Fender l. H. 1 1 1 1 161 1 1 164 4915 4204 165 4206 Battery Clamp 1 166 167 4211 Spacer 4213 � Shift Stick 163 1 1 1 1 Belt Guard 1 1 1 Gas Cop 1754 �" Std. Pipe Nipple 95 96 1786 1787 Fuel Strainer Straight Fitting 1 1 168 4440 97 99 1796 Fuel Line 1 169 4216 2638 2639 Tecumseh 1 1 170 4217 171 4218 4220 ).{ Front Axle 1 1 1 4222 Quadrant 1 174 175 4907 4232 lift Throttle 1 1 176 4233 Choke 1 177 4235 Differential Pinion Gear 4 lower Plunger Ass'y. 1 1 Tank 1 1 182 4905 4438 4407 4249 lift Lever 1 178 180 181 183 1861 3279 Tecumseh 5 � " Lg. 6 hp. Engine (Electric) 6 hp. Engine (Recoil) Rod Control Stud Off.On Switch (33R) Shift Fork 1 1 2 103 104 105 3515 Front Shift Roil 106 3516 Rear Shift Rail 107 108 3517 3518 Boll Stop 110 111 3522 Input Gear 3523 Hi and 2nd Gear 112 113 3524 3525 Low and Reverse Gear Cluster Gear 1 1 114 3526 Splined Pinion 1 3503 3514 Shift Collar 172 173 he 101 102 yW 3998 94 100 1 el Spring Stop 1 1 2 1 Bottom 4405 Fuel Tank Ass'y. 4901 Front Spindle 1 2 4410 Wheel Horse Decal 2 4412 80ttom Steering Support 4413 Steering 1 1 1 186 187 117 3537 Seat Spring 118 119 3573 1143 � .20 1 1 1 190 120· 3577 3578 Boot 2 1 191 Plunger Guide 1 192 3605 3624 Tie Rod 1 Compression Spring 1 193 194 3653 Battery 188 189 3656 3680 Switch (33E) Plunger Cap 1 196 197 3900 Transmission Case R.H. 1 199 195 Sector 4414 Steering Wheel 4415 4416 Hood 4417 4418 Brake Set Lever 1 1 Shift Decal 1 4419 Shield 1466 Retainer 1 2 1539 4422 Bushing 1 Instrument Decal 4429 Clutch Rod 1 1 Lawson Engine Base 1 1 om 125 126 127 1 1 .c se or H 184 185 Reduction Gear 123 124 Std. 1 ).{ Std. Pipe Nipple x 1 1 1 Reduction Pinion Button Head Screw � Pipe Cap 900 1 3527 % Std. Pipe Elbow 1 Fuel Tank 3528 x 1 3 Std. Pipe Nipple 4406 115 Shift Pin Stop ).{ x Hole Plug 116 121 122 V -.-- 69 76 .."-.-/ '-����.. Quantity �.�+.--- -- -�- -t---- -� . .. Bushing 1504 68 ... .... 128 3901 Transmission Case L.H. 1 200 3902 4430 Clutch Pedal 129 Brake Drum 1 4431 Ground Switch to Coil Wire 130 3903 Brake Shaft Gear 4432 Starter Switch to Starter Wire 131 3904 Axle 1 2 201 202 1 203 Ballery to Starter Wire 132 3905 Differential 2 204 4433 4434 133 3906 Bull Gear 1 208 1227 134 3907 Spline Shaft 1 'f6 1 1 209 3930 Hood Stand Channel Strut Case Generator to Ammeter Wire x 1% Roll Pin 1 1 1 2 135 3908 Axle Gear 2 215 4900 Frame Ass'y. 1 136 3909 Differential Pin 5 4904 Hitch 1 137 138 139 3910 3912 Clu ster 1 217 218 4427 Hood Stand Channel Ass'y. 1 Gasket 1 219 1755 Street EI 4437 Brake Band Ass'y. 1 220 1756 �" lock Nut 1 1 140 3915 Locating Pin 2 . _L._..__. . .._ ... -!-_.�. Shaft 90· �" Std. .. .. w yW .M w w he Lawn Ranger Rotary Mower When _. Quantity 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 Part No. 3130 1185 1194 1122 1613 1042 1426 3141 1304 3757 1587 1418 1408 1343 4935 4934 1423 4940 4939 4938 1017 1002 4936 1425 4937 4914 1434 3725 1391 4121 4177 1484 3710 Name Quantity Gear - Foce 2 Wo.her - Lock % 2 Key - Woodruff #5 2 Key - Woodruff #9 Pulley 1 Pulley 3X Dia. 1 Set ;'6-18 x ;'6 Screw 1 Bolt Hex %·16 x lY.t 6 Cover Geor 2 Screw - Hex Hd. #8 32 x 14Self Top. 8 Plug - Button 2 Belt 43" A Section 1 Wosher - Lock % 4 Nylock %.16 Nuts 12 Nut % x 18 2 Bracket L.H. 1 Bracket R.H. 1 Bolts %-16 x % 4 Link - Front 2 Link - Rear 2 Rod - Front (Link Pivot) 1 Washer X SAE Plain 5 Pin - Cotter Va x 1 5 Rod - Rear (Link Pivot) 1 Bolt %.16 x 1 4 Spacer 4 Lift Bar 1 Washer % SAE Plain 4 Cover - End Plote 2 10 Screw - Rd. Hd. Mach. 14·20 x % (SEMS) Wheel - 6" Dia. 2 Stud - Shoulder 2 DecoI (Caution) 2 Deco! 2 om .c Deck 1 Clutch Latch 1 Clutch Pedal 1 Shield 1 Twin Housing & Bearings 1 Housing 1 Bearing 4 Oil Seal 2 Spindle 2 Cup 2 Pin - Roll 14x % 4 Blade Rotory - R.H. 1 1 Blade - Rotary - L.H. Washer - Dome 2 Screw - Hex - Nylock % - 16 x % 2 4 Race - Bearing Thrust 2 Bearing - Thrust Key #5 2 Gear Spur 2 Snap Ring 2 Fitting 2 Grease Hex. H. Cap Screw ;'6 x 18.% 4 Hex. Hd. Nut Nylock ;'6 x 18 4 As.'y. Housing - Cron Shaft 2 Housing 1 Bearing 1 Pulley Idler Bushing Idler Bolt Hex %.16 x % CP Bolt 142- 0 x 1 CP 1 1 Nut - Nylock 14·20 Washer - 14 SAE CP 1 Spring - Clutch 2 Shoft 1 Ref. No. Part. se 4917 4924 4927 4931 4151 3726 1508 1303 3724 3716 1382 3718 3719 1336 1398 1535 1534 1194 3131 1127 1030 1443 1407 4150 3138 1515 1623 1536 1363 1439 1406 1436 1486 3715 Name Name of or 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Part No. Ordering Parts Always List Part Number and H Ref. No. el PARTS LIST FOR LAWN RANGER ROTARY MOWER 8 -16-62 Form No. 135