Download SERVICE MANUAL - Whaley Food Service
Transcript
Henny Penny Heated Merchandiser Model CM-5/7 Model CMT-5/7 Model HM-3/5/7 Model HMT-3/5/7 Model HS/HST-3 SERVICE MANUAL TABLE OF CONTENTS Section Page Section 1 INTRODUCTION 1-1 Heated Merchandiser 1-2 Features 1-3 Assistance 1-4 Model Variations 1-5 Safety 1-1 1-1 1-1 1-1 1-2 1-2 Section 2 INSTALLATION 2-1 Introduction 2-2 Unpacking 2-3 Electrical Connection 2-4 Electrical Data Table 2-5 Cabinet Dimensions 2-1 2-1 2-1 2-2 2-2 2-3 Section 3 OPERATION 3-1 Operating Controls 3-2 Start-Up 3-3 Operation With Product 3-4 Recommended Settings for Heated Merchandiser 3-5 Shut Down and Clean Up 3-1 3-1 3-4 3-5 3-6 3-6 Section 4 PROGRAMMING 4-1 Entering Program Mode 4-2 Programming Upper Heat 4-3 Programming Water Heat 4-4 Programming Air Temperature 4-5 Special Program Mode 4-6 Error Codes 4-1 4-1 4-1 4-1 4-1 4-1 4-2 Section 5 MAINTENANCE 5-1 Introduction 5-2 Removing Front Glass 5-3 Radiant Heaters 5-4 Light Socket 5-5 Water Heater 5-6 Base Heaters 5-7 Air Blowers 5-8 Heat Probe (Air) 5-9 Transformer 5-10 Product Probe Outlet 5-11 Heat Relay 5-1 5-1 5-1 5-3 5-3 5-4 5-5 5-6 5-6 5-7 5-7 5-8 TABLE OF CONTENTS (Continued) Section Page Section 5 MAINTENANCE (Continued) 5-12 Cooling Fan 5-13 Printed Circuit Board 5-14 Gas Shocks 5-15 Fuse and Fuse Holder 5-16 Power and Light Switch 5-17 Wiring Diagrams 5-8 5-8 5-9 5-9 5-10 5-11 5-12 Section 6 TROUBLESHOOTING 6-1 Introduction 6-2 Troubleshooting 6-1 6-1 6-1 Section 7 PARTS INFORMATION 7-1 SECTION 1. INTRODUCTION 1-1. HEATED MERCHANDISER The Henny Penny Heated Merchandiser is a basic unit of food processing equipment used to display the food product and maintain the temperature of hot foods in a commercial food service operation. Using a combination of precise heat, humidity and slowly circulating air, Henny Penny's even heat process creates the ideal environment to maintain the taste and quality of freshly-cooked foods for hours. 1-2. FEATURES • Unique THERMA-VEC even heat process re-circulates heated air, keeping temperature precise and stable throughout the case. • Contemporary curved glass cases present 100 per cent product visibility. • Individually controlled radiant heaters over each well. • Air heating elements under pans. • Humidity controlled with heated water pan. • Touch pad electronic controls and LED readouts. • Incandescent lighting for attractive food presentation. • Fold-down cutting board. 1-3. ASSISTANCE Should you require outside assistance, just call your local, independent Henny Penny distributor maintained by Henny Penny Corporation. In addition, feel free to contact our corporate headquarters in Eaton, Ohio. Dial 1-800-543-6243 toll free, except in Ohio, dial 1-800-762-2964. Henny Penny CABINET DIMENSIONS Model CM/CIVIT- 5/7 HM/HMT- 3/5/7 HS/HST- 3 2-5 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT - 5/7 HM/HMT- 3/5/7 HS/HST-3 SECTION 3. OPERATION 3-1. OPERATING CONTROLS This section describes the functions of all operating controls. Item No. 1 Description Function Increase Switch The increase switch is used during programming to increase the displayed value by one setting. It is also used to enter special program mode. 2 Decrease Switch The decrease switch is used during programming to decrease the displayed value by one setting. It is also used to enter special program mode. 3 Air Heat Switch This switch is depressed to set the air heat temperature set point. 4 Water Heat Switch This switch is depressed to set the water heat. 5 Upper Heat - 1, 2, 3, 4, These switches are depressed to set the radiant heaters. and 5. NOTE HM-3 will have 1, 2, and 3. HM-7 will have 1 through 7. 6 Temperature Display The temperature display is a three-digit red LED display. The display is used to show the air and product temperatures. It is also used to display control error messages, and during programming to show the parameter being programmed. 7 8 Ready LED This LED turns on when the merchandiser is ready to hold product. It turns on to indicate the air temperature is near the set point. Display Air Temp LED This LED turns on when the merchandiser air temperature is shown in the display. 9 Display Probe Temp LED This LED turns on when the product probe temperature is shown in the display. 10 UPPER HEAT 1, 2, 3, 4, These LED's turn on during operation when the associated and 5 LED's radiant heater turns on. NOTE The HM-3 has three LED's. The HM-7 has seven LED's. Henny Penny Item Description No. 11 Water Heat LED Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Function This LED turns on during operation when the water heater is on. 12 Air Heat LED This LED turns on during operation when the air heater is on. 13 Power Switch The power switch is a two-position switch used to switch electrical current to the unit. 14 Light Switch The light switch is a two-position switch that turns the lights off and on. 15 Fuse The fuse (2) is a protective device for the PCB control, motor, and lights circuit. The fuses are a 15 amp rating and must be replaced by a fuse of the same size and rating. Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny 3-2. START-UP Model CM/CMT.5/7 HM/HMT.3/5/7 HS/HST-3 Normal Operation 1. Turn POWER and LIGHTS to the ON position. 2. Fill water pan with approximately one quart of water (1 inch in water pan). 3. Allow approximately 30 minutes preheat time. 4. Check air temperature setting by depressing switch marked AIR HEAT. 5. Check water temperature setting by depressing switch marked WATER HEAT. NOTE Water heat settings read 1, 2, 3, etc. One meaning the heat is on 10% of the time, and ON meaning the heat is on 100% of the time. Refer to programming section for correct setting changes. If you wish to operate unit with no humidity, program water heat to OFF. 6. Check upper heat settings by depressing numbered switch corresponding to each well. NOTE HM-3 is numbered 1 through 3; HM-5 is number 1 through 5; HM-7 is numbered 1 through 7. Refer to "Recommended Settings for HM-3, HM-5, and HM-7." 7. As a rule, a lower upper heat setting, such as 3 or 4, holds dense foods like macaroni and cheese or cherry cobbler. Use higher upper heat settings for less dense foods, such as fried chicken. 8. If using a probe to check product temperature, plug probe into probe outlet (just left of the control panel) and place probe into the product you are testing. 9. Depress switch marked PROBE TEMP DISPLAY. Henny Penny 3-3. OPERATION WITH PRODUCT Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 1. Rotate food from front to back. 2. Food in half-full pans does not hold as well as food in full pans. Rotate pan to back of merchandiser where it is directly under upper heating elements or move food to a smaller pan that has been preheated. 3. When "freshening" foods such as macaroni and cheese with added water, heat the water in a clean container until is it 10 to 20 degrees above the desired holding temperature of the food. This will keep food at a safe serving temperature. Depending on the amount of water, the temperature can drop 10 to 20 degrees in as little as five minutes. 4. When transferring hot foods in the heated merchandiser to clean pans, preheat the clean pan. Transferring hot foods to room temperature pans can cause the temperature of the food to drop 20 degrees or more, thus causing food to be at an unsafe serving temperature. 5. To keep hot foods from drying too fast, keep a clean misting bottle (such as you find in a garden supply store) with a mixture of 1/3 vegetable oil and 2/3 water on hand. Set the nozzle for a fine mist. Shake the vegetable oil and water mixture well. Spray surface of food immediately, shaking the bottle between each entree. Frequency foods need to be misted will depend upon the unique characteristics of the food, the water heat setting in the case and atmospheric conditions. Do not use this mixture on foods with a pastry crust or crumb toppings where a dry surface is desirable. 6. If prepackaging foods, place containers directly under upper heating elements (in back of the case) for maximum holding time. Upper heat may need to be increased slightly. Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 SECTION 4. PROGRAMMING 4-1. ENTERING PROGRAM MODE Program mode is entered by depressing and holding a parameter switch. Parameter switches are AIR HEAT, WATER HEAT, and the UPPER HEAT switches. 4-2. PROGRAMMING UPPER HEAT Depress and hold switch marked UPPER HEAT. Using the INCREASE or DECREASE switches, program the desired percentage on time of the radiant heater. The display will be numbered 1 through 9. One meaning 10%; 2 meaning 20%, etc. "OFF" means the heater is always off- "ON" means the heater is always on. Repeat procedures until all radiant heaters are programmed. 4-3. PROGRAMMING WATER HEAT The procedure for programming the water heat is identical to that of programming the radiant heat, except that the WATER HEAT LED flashes. 4-4. PROGRAMMING AIR TEMPERATURE Depress switch marked AIR HEAT. Using the INCREASE or DECREASE button, program desired air temperature. Air temperature can be programmed between 120°F and 175°F. 4-5. SPECIAL PROGRAM MODE Special program mode is used to perform the following functions: • Calibrating the air and product temperature probes. • Initializing the program. • Changing the control for Fahrenheit 0 /Celsius". To enter the special program mode, depress and hold the INCREASE switch and turn the power switch to the "ON" position. Display will read "SP" for special program. To exit special program, turn the power switch to "OFF". To calibrate air temperature, depress and hold the DISPLAY AIR TEMP switch. Display will show the actual air temperature seen by the probe. Use your INCREASEDECREASE switch to adjust the displayed temperature. Temperature can be adjusted plus or minus 15 degrees. Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT- 5/7 HM/HMT-3/5/7 HS/HST-3 SECTION 8. MAINTENANCE Henny Penny Model CM/CMT- 5/7 HM/HMT - 3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT.5/7 HM/HMT.3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT.5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 SECTION 6. TROUBLESHOOTING Henny Penny PROBLEM With power switch in POWER position, unit is completely inoperative (NO POWER) Unit will not heat Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CAUSE • Open Circuit • Check to see that unit is plugged in. • Check breaker or fuse at supply box. • Check control panel fuses per paragraph 5-15. • Check voltage at wall receptacle. • Check MAIN POWER switch per section 5-16. Replace if defective. • Check cord and plug for loose connections • Control board defective. • Check for 12 volt input from transformer. Replace if defective. • Transformer defective. • Check input and output voltage Replace if defective. • Control board not calling • Check set point reading. If unit for heat. • Power on, board has no display. No air heat. CORRECTION • Faulty heat relay. • Faulty air heater. • Unit not pre heated below setpoint and not calling for heat, control board defective. • Hi limit tripped. Check for defective hi limit, or defective blower motor. • Check and replace per section 5-11. • Check and replace per section 5-6. • Pre heat unit with pans in place before loading product. Henny Penny PROBLEM No radiant heat. Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CAUSE CORRECTION • Faulty input/output board. • Replace input/output board. • Faulty radiant heater. • Replace radiant heater per • Faulty input/output board. • Replace input/output board. • Faulty water heater. • Replace water heater per section 5-3. No water heat. section 5-5. No lights. • Light switch defective. • Replace per section 5-16. • Light relay defective • Replace per section 5-11 ( Same as heat relay ) Canopy glass fogging. • Light socket shorted • Replace per section 5-4. • Light bulb blown • Replace light bulb. • Air blowers not circulating • Replace blower motor per heated air across glass. • Water heat setting too high. section 5-7. • Lower water heat setting as per section 4. • Radiant heat setting too low. • Raise radiant heat setting as per section 4. Product not holding • Doors are left open. temperature. • Keep doors closed except to load and unload product. • Heat settings too low. • Adjust heat settings as per section 4. • Low or improper voltage. • Using meter, compare recep tacle voltage to data plate voltage. • Product held too long. • Hold product only for recommended time. • Product not placed correctly in unit. • Place product in unit as per section 3-3. Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 SECTION 6. PARTS INFORMATION HM-3/5/7 Service Parts List No. Part Number Description 3 1 1 1 1 1 1 1 2 2 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18 18 19 20 21 21 22 22 23 23 24 24 25 25 26 26 26 26 28 29 30 31 31 32 33 37000 54033. 37001 54031 39027 54129 54130 37972 37973 39114 37638 41507 40833* 42440* 39216 40097 28979 PL01-006* 18135 MS01-162 22609 22610 ME50-003* NS03-013* EF02-040* 37230 37757 42969 43794 39974 16685 37059 44976 37060 48020 39795 54041 BL01-009 BL01-015 54181 64257 38413 37536 37537 38412 37127* 30723 * 52843 37815 42341 16688 37128 Front Viewing Glass - 3 Pan (Before July 1, 1994) Front Viewing Glass Assy. - Complete - 3 Pan Front Viewing Glass Assy. - 5 Pan (Before July 1,1994) Front Viewing Glass Assy. - Complete - 5 Pan Front Viewing Glass Assy. - 7 Pan (Before July 1,1994) Front Viewing Glass Assy. Complete - RH - 7 Pan Front Viewing Glass Assy. Complete - LH - 7 Pan Sliding Door Assembly - 3 Pan Sliding Door Assembly - 5 Pan Sliding Door Assembly - 7 Pan Water Pan Assembly (Before July 1, 1994) Water Pan Assembly Probe Bracket Temperature Probe PC Board Assy. Blower Motor Series Regulating Thermostat Transformer Plug - Bottom End Clamp Mounting Channel Terminal Block Barrier Spacer Cage Nut Bushing - Snap Bracket - Drop Shelf Side Viewing Panel Side Viewing Panel - (Mir)-Left Side Viewing Panel - (Mir)-Right Fan Blade Fan Guard Heater - Lower - 240v Heater - Lower - 208v Heater - Water - 240v Heater-Water-208v. Light Socket Light Socket - CE Light Bulb- 120v- lOOw Light Bulb - 240v - 60w Heater - Upper Radiant - 240v Heater - Upper Radiant - 208v Decal - Control Panel - 7 Pan - Left Decal - Control Panel - 3 Pan Decal - Control Panel - 5 Pan Decal - Control Panel - 7 Pan Bracket for Plug Relay - 3 Pan Probe- 5 ft. Receptacle Assy. - Probe (Control Panel) Receptacle Assy. - Probe (Uprights) Cooling Fan Gas Shock - 3 Pan (Before May 1, 1994) 1 1 2 1 1 1 1 2 2 1 2 2 3 2 2 4 2 2 2 2 2 2 4 2 2 1 1 6 6 6 6 3 3 1 1 1 1 1 2 1 2 *not shown **Front Viewing Glass before July 1, 1994, 02736 Tape Kit must also be ordered. Qty. Per Unit 5 7 1 1 2 1 1 1 1 2 2 1 2 2 3 2 2 4 2 2 2 2 2 2 4 3 3 1 1 10 10 10 10 5 5 1 1 2 1 1 2 1 - 2 1 1 2 2 2 2 2 3 2 2 2 2 3 2 2 4 2 4 2 2 2 3 5 4 4 2 2 14 14 14 14 7 7 1 1 3 4 3 3 2 1 2 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HM-3/5/7 Service Parts List - Continued No. 33 33 33 33 34 34 34 34 35 35 35 36 37 38 39 39 40 40 40 41 41 42 43 43 44 44 44 44 45 45 45 46 46 47 47 48 48 49 51 52 53 53 53 54 54 54 55 55 55 55 55 58 59 60 *not shown Part Number 37129 41751 41750 42620 43258 39181 43262 39840 37841 37849 41233 PN01-016* PN01-017* LW01-004* 37044 41760 37231 42088 39180 41154 39026 54011 41024 42844 37061 37062 39008 39009 37063 37064 39010 37130 41778 EF02-007 EF02-083 EF02-006 EF02-085 43768 37770RB SC06-045* 37184 37185 39025 37182 37183 39024 42183* 42595 42291* 42468* 42469* 36210* 29523* 54003 * Description Gas Shock - 5 Pan (Before May 1, 1994) Gas Shock - 3 Pan Gas Shock - 5 Pan Gas Shock Assy. - 7 Pan Cutting Board - 3 Pan Cutting Board (Poly) - 3 Pan Cutting Board - 5 Pan Cutting Board (Poly) - 5 Pan Power Cord Assy. - 3 Pan Power Cord Assy. - 5 Pan Power Cord Assy. - 7 Pan Clevis Pin Cotter Pin Lockwasher Hinge Cap (Before May 1, 1994) Hinge Cap Hinge Block Assy. (Before May 1, 1994) Hinge Block Assy. Hinge Block Assy. - Center - 7 Pan Hinge Pin Hinge Pin - Center Tape - Acrylic Foam Crank (Before April 1, 1994) Crank Hinge Extrusion - 3 Pan Hinge Extrusion - 5 Pan Hinge Extrusion - 7 Pan - Right Hinge Extrusion - 7 Pan - Left Clamp Extrusion - 3 Pan Clamp Extrusion - 5 Pan Clamp Extrusion - 7 Pan Pivot Support (Before May 1, 1994) Pivot Support Fuse - 15 Amp Fuse - 20 Amp Fuse Holder - 15 Amp Fuse Holder - 20 Amp Power Switch PC Board - Output Shoulder Screw Lower Track - 3 Pan Lower Track - 5 Pan Lower Track - 7 Pan Upper Track - 3 Pan Upper Track - 5 Pan Upper Track - 7 Pan Air Deflector - 3 Pan Air Deflector - 5 Pan - Alb. Air Deflector - 5 Pan Air Deflector - 7 Pan - Right Air Deflector - 7 Pan Left Replaceable Beeper Probe Legs 3 2 1 1 1 2 2 2 2 2 2 2 2 1 4 4 1 1 2 2 2 2 2 1 1 1 1 1 1 2 4 Qty. Per Unit 5 2 2 1 1 1 2 2 2 2 2 2 2 2 2 4 4 1 1 2 2 2 2 2 1 1 1 1 1 1 1 2 4 7 2 2 2 2 1 4 4 4 3 3 2 2 1 2 2 2 4 4 1 1 1 4 4 2 2 2 2 2 1 1 1 1 2 2 4 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HM-3/5/7 Service Parts List - Continued Part Number 41056 41055* 41057* 41162* 41163* 42661* 14151* 14155* 37159* 37371* 43568 43569 43666 43667 55870* 55871* No. 61 61 61 62 62 62 63 63 64 65 67 67 67 67 68 69 Description Seal - Canopy Glass - 3 Pan (Before May 1, 1994) Seal - Canopy Glass - 5 Pan (Before May 1, 1994) Seal - Canopy Glass - 7 Pan (Before May 1, 1994) Seal - Side Glass - 3 Pan Seal - Side Glass - 5/7 Pan Seal - Side Glass - Alb. Kit - Digital Display Uprights - O/S Kit - Digital Display Uprights - 90° Pan Support - Long Pan - Cross Support Upright Stud Assy. - Right - 90° w/probe guard Upright Stud Assy. - Left - 90 ° w/probe guard Upright Stud Assy. - Left - O/S w/probe guard Upright Stud Assy. - Right - O/S w/probe guard Right Water Pan Support Bracket Left Water Pan Support Bracket 3 1 2 2 2 2 2 6 1 1 1 1 1 1 Qty. Per Unit 5 1 2 2 2 2 4 10 7 1 2 2 2 2 6 14 *not shown HMT-3/5/7 Service Parts List No. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 3 3 4 5 6 7 8 9 10 Part Number 37000 54032 54128 54127 37001 54030 54035 54034 39027 54036 54037 54134 54135 54132 54133 38946 38915 45171 41028 37638 41507 40833* 42440* 39216 40097 28979 PLO 1-006* 18135 *not shown Description Front Viewing Glass - 3 Pan (Before July 1, 1994) Front Viewing Glass Assy. - Complete - 3 Pan Front Viewing Glass Assy. Complete - 3 Pan - Huss Front Viewing Glass Assy. Complete - 3 Pan - Tyler Front Viewing Glass Assy. - 5 Pan (Before July 1,1994) Front Viewing Glass Assy. Complete - 5 Pan Front Viewing Glass Assy. Complete - 5 Pan - Huss Front Viewing Glass Assy. Complete - 5 Pan - Tyier Front Viewing Glass Assy. - 7 Pan (Before July 1,1994) Front Viewing Glass Assy. Complete - RH - 7 Pan Front Viewing Glass Assy. Complete - LH - 7 Pan Front Viewing Glass Assy. Complete - 7 Pan - Huss RH Front Viewing Glass Assy. Complete - 7 Pan - Huss. LH Front Viewing Glass Assy. Complete - 7 Pan - Tyier RH Front Viewing Glass Assy. Complete - 7 Pan - Tyier LH Sliding Door Assy. - 3 Pan Sliding Door Assy. - 5 Pan Sliding Door Assy. - HMT-5 (4 doors) Sliding Door Assembly - 7 Pan Water Pan Assembly (Before July 1, 1994) Water Pan Assembly Probe Bracket Temperature Probe PC Board Assy. Blower Motor Series Regulating Thermostat Transformer Plug - Bottom End Clamp 3 l l l l 2 1 1 1 2 2 2 1 2 2 Qty Per Unit 5 l 1 1 1 2 4 1 1 1 2 2 2 1 2 2 **Front viewing glass before July 1, 1994, 02736 Tape Kit must also be ordered. 7 2 1 1 1 1 1 1 2 2 2 2 2 3 2 2 2 2 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HMT-3/5/7 Service Parts List - Continued *not shown No. Part Number Description Qty. Per Unit 3 5 7 11 12 13 14 15 16 17 17 18 18 18 18 18 18 18 18 18 19 20 21 21 22 22 23 23 24 24 25 25 26 26 26 26 26 27 28 29 30 31 31 31 32 33 33 33 33 33 34 34 34 34 34 34 35 35 35 36 37 38 MS01-162 22609 22610 ME50-003* NS03-013* EF02-040* 37230 49297 39938 42229 43791 42003 42230 43793 42009 42231 43792 39974 16685 37059 44976 37060 48020 39795 54041 BLO 1-009 BL01-015 54181 64257 41019 41020 41021 38413 49046 36900 37127 30723 52843 37420 37815 42341 16688 37128 41751 37129 41750 46502 43258 39181 43262 39840 49308 49309 37841 37849 41233 PN01-016* PN01-017* LW01-004* Mounting Channel Terminal Block Barrier Spacer Cage Nut Bushing - Snap Bracket - Drop Shelf Cutting Board Brace - KFC Side Viewing Panel Side Viewing Panel (Mir)-Left Side Viewing Panel (Mir)-Right Side Viewing Panel - Hussmann Side Viewing Panel - Hussmann (Mir)-Left Side Viewing Panel - Hussmann (Mir)-Right Side Viewing Panel - Tyier Side Viewing Panel - Tyier (Mir)-Left Side Viewing Pane] - Tyier (Mir)-Right Fan Blade Fan Guard Heater - Lower - 240 v Heater - Lower - 208 v Heater - Water - 240 v Heater-Water-208 v Socket - Light Socket - Light - CE Light Bulb- 120v- lOOw Light Bulb - 240v - 60w Heater - Upper Radiant - 240 v Heater - Upper Radiant - 208 v Decal - Control Panel - 3 Pan Decal - Control Panel - 5 Pan Decal - Control Panel - 7 Pan Decal - Control Panel - 7 Pan - Left Decal - Control Panel - KFC PC Board Assembly - Control Bracket for Plug Relay Probe - 5 ft. Plug - Probe Receptacle Assy. - Probe (Control Panel) Receptacle Assy. - Probe (Uprights) Cooling Fan Gas Shock - 3 Pan (Before April 1, 1994) Gas Shock-3 Pan Gas Shock - 5 Pan (Before April 1, 1994) Gas Shock-5 Pan Gas Shock Assy. - HM-7 Cutting Board - 3 Pan Cutting Board (Poly) - 3 Pan Cutting Board - 5 Pan Cutting Board (Poly) - 5 Pan Cutting Board - KFC - HMT-3 Cutting Board - KFC - HMT-5 Power Cord Assy. - 3 Pan Power Cord Assy. - 5 Pan Power Cord Assy. - 7 Pan Clevis Pin Cotter Pin Lockwasher 3 2 2 4 2 2 1 2 2 2 2 2 2 2 2 2 2 4 2 2 1 1 6 6 6 6 3 3 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1 1 2 2 2 3 2 2 4 2 2 1 2 2 2 2 2 2 2 2 2 2 4 3 3 1 1 10 10 10 10 5 5 1 1 1 1 2 1 1 1 2 1 1 1 2 1 1 1 1 2 2 2 3 2 2 4 2 4 2 2 2 2 2 2 2 2 2 3 5 4 4 2 2 14 14 14 14 7 7 1 1 2 3 4 3 3 3 2 1 4 2 2 2 1 4 4 4 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HMT-3/5/7 Service Parts List - Continued No. Part Number Description 3 39 39 40 40 40 41 41 42 43 43 44 44 44 44 45 45 45 46 47 47 48 48 49 51 52 52 53 53 53 54 54 54 55 55 55 58 59 60 61 61 61 62 62 62 63 63 64 65 67 67 67 67 68 68 69 70 71 37044 41760 37231 42088 39180 41154 39026 54011 41024 41761 37061 37062 39008 39009 37063 37064 39010 37130 EF02-007 EF02-083 EF02-006 EF02-085 43768 37770 SC06-045* SC06-060* 39961 39942 39025 37182 37183 39024 39978* 39977* 39979* 36210* 29523* 54003* 41056* 41055* 41057* 38932* 46624* 43549* 14122 14123 37159* 37371* 42333 42340 43562 43563 05835 05387 55870* 55871* 51530 Hinge Cap (Before April 1, 1994) Hinge Cap Hinge Block Assy. (Before April 1, 1994) Hinge Block Assy. Hinge Block Assy.- Center - 7 Pan Hinge Pin Hinge Pin - Center - 7 Pan Tape - Acrylic Foam Crank (Before April 1, 1994) Crank Hinge Extrusion - 3 Pan Hinge Extrusion - 5 Pan Hinge Extrusion -7 Pan - Right Hinge Extrusion - 7 Pan-Left Clamp Extrusion -3 Pan Clamp Extrusion - 5 Pan Clamp Extrusion - 7 Pan Pivot Support Fuse - 15 Amp Fuse - 20 Amp Fuse Holder - 15 Amp Fuse Holder - 20 Amp Power Switch PC Board - Output Shoulder Screw Shoulder Screw - HMT-7 Lower Track - 3 Pan Lower Track - 5 Pan Lower Track - 7 Pan Upper Track - 3 Pan Upper Track - 5 Pan Upper Track - 7 Pan Air Deflector - 3 Pan Air Deflector - 5 Pan Air Deflector - 7 Pan Replaceable Beeper Probe Legs Seal - Canopy Glass - 3 Pan (Before April 1, 1994) Seal - Canopy Glass - 5 Pan (Before April 1, 1994) Seal - Canopy Glass - 7 Pan (Before April 1, 1994) Seal - Side Glass Seal - Side Glass - Huss. Seal - Side Glass - Tyler Kit - Digital Display Uprights - 90' Kit - Digital Display Uprights - 0/S Pan Support - Long Pan - Cross Support Upright Stud Assy. - Left - 90° - D/D - Probe Guard Upright Stud Assy. - Rt. - 90° - D/D - Probe Guard Upright Stud Assy. - Right - 0/S -D/D- Probe Guard Upright Stud Assy. - Left - 0/S- D/D - Probe Guard Bun Pan Insert - KFC - KMT-5 Bun Pan Insert - KFC - KMT-3 Right Water Pan Support Bracket Left Water Pan Support Bracket Contactor- 3 ph Albertsons 2 2 2 2 2 1 4 4 1 1 2 2 2 2 1 1 1 1 1 1 2 4 1 2 2 2 2 2 2 6 1 1 1 1 1 1 1 1 *not shown Qty. Per Unit 5 7 2 2 2 2 2 2 4 4 1 1 2 2 2 2 1 1 1 1 1 1 2 4 1 2 2 2 2 2 4 10 1 1 1 1 1 1 1 1 3 3 2 2 1 2 2 2 4 4 1 1 1 4 2 2 2 2 1 1 1 1 2 2 4 1 2 2 2 2 2 6 14 1 1 1 1 1 1 1 Henny Penny Service Parts List No. 1 1 1 1 1 1A 1A 1 1 1 1 1 1A 1A 1 1 1 1 1 1 1A 1A 1 1 1A 1A 2 2 2 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18A 18 18 18 18A 18 18 18 18A 18 18 18 18A 18A 18 18 18 *not shown Part Number 37000 54109 54111 54105 54107 54110 54112 37001 54136 54138 54140 54142 54106 54108 54119 54117 54113 54115 54150 54146 54120 54118 54148 54144 54116 54114 37973 39114 38915 41028 37638 41507 40833* 42440* 39216 40097 28979 PL01-006* 18135 MS01-162 22609 22610 ME50-013 NS03-013 EF02-040 37230 38995 37757 42969 43794 38993 39938 42229 43791 42871 42230 43793 42003 42871 42872 42009 42231 43792 Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CM/CMT-5/7 Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Description Front Viewing Glass - CM/CMT-5 (before July 1, 1994) Front Viewing Glass Assy. Complete. - CM-5 RH Front Viewing Glass Assy. Complete - CM-5 LH Front Viewing Glass Assy. Complete - CMT-5 RH Front Viewing Glass Assy. Complete - CMT-5 LH Glass-Canopy Guard - Assy. Complete - CM-5/7 RH Glass-Canopy Guard - Assy. Complete - CM-5/7 LH Front Viewing Glass - CM/CMT-7 (before July 1, 1994) Front Viewing Glass Assy. - CM-7 RH Front Viewing Glass Assy. - CM-7 LH Front Viewing Glass Assy. - CMT-7 RH Front Viewing Glass Assy. - CMT-7 LH Glass Canopy Guard Complete - CMT-5/7 RH Glass Canopy Guard Complete- CMT-5/7 LH Front View Glass Assy. Complete - CMT-5-Huss. LH Front View Glass Assy. Complete - CMT-5-Huss. RH Front Viewing Glass Assy. Complete - CMT-5-Tyler RH Front Viewing Glass Assy. Complete - CMT-5-Tyler LH Front Viewing Glass Assy. Complete - CMT-7-Huss. RH Front Viewing Glass Assy. Complete - CMT-7-Huss. LH Glass Canopy Guard Assy. Complete - CMT-5/7-Huss. LH Glass Canopy Guard Assy. Complete - CMT-5/7-Huss. RH Front Viewing Glass Assy. Complete - CMT-7-Tyler RH Front Viewing Glass Assy. Complete - CMT-7-Tyler LH Glass Canopy Guard Assy. Complete - CMT-5/7-Tyler LH Glass Canopy Guard Assy. Complete - CMT-5/7-Tyler RH Sliding Door Assembly - CM-5 Sliding Door Assembly - CM-7 Sliding Door Assembly - CMT-5 Sliding Door Assembly - CMT-7 Water Pan Assembly (Before July 1, 1994) Water Pan Assembly Probe Bracket Temperature Probe PCB Assembly Blower Motor Series Regulating Thermostat Transformer Plug-Bottom End Clamp Mounting Channel .292 Terminal Block Barrier Spacer Cage Nut Bushing- Snap Bracket - Drop Shelf Glass - Center Panel - CM-5/7 Side Viewing Panel - CM-5/7 Side Viewing Panel - Mir.-CM-5/7-Left Side Viewing Panel - Mir.-CM-5/7-Right Glass - Center Panel - CMT-5/7 Side Viewing Panel - CMT-5/7 Side Viewing Panel - Mir.-CMT-5/7-Left Side Viewing Panel - Mir.-CMT-5/7-Right Glass - Center Panel - CMT-5/7-Huss. Side Viewing Panel - CMT-5/7-Mir.-Huss.-Left Side Viewing Panel - CMT-5/7-Mir.-Huss.-Right Side Viewing Panel - CMT-5/7-Huss. Glass - Center Panel - CMT-5/7-Huss. Glass - Center Panel - CMT-5/7-Tyler Side Viewing Panel - CMT-5/7-Tyler Side Viewing Panel - CMT-5/7-Mir.-Tyler-I.eft Side Viewing Panel - CMT-5/7-Mir.-Tyler-Right Qty. Per Unit 7 8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 1 1 1 1 1 1 2 2 2 2 2 2 1 2 1 1 2 2 3 3 1 1 2 2 4 4 2 2 2 4 1 1 2 2 2 2 2 2 1 1 9 2 2 2 2 2 1 1 2 2 2 2 2 2 1 1 1 I 2 2 2 2 2 2 **Front Viewing Glass before July 1, 1994, 02736 Tape Kit must also be ordered. Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CM/CMT-5/7 Service Parts List - Continued No. 23 23 24 24 25 25 26 26 26 26 26 26 26 26 27 28 29 30 31 31 31 32 33 33 33 33 33 33 33 34 34 35 35 36 37 38 39 39 40 40 40 41 41 41 42 43 43 43 43 44 44A 44 44 44 44 45 45 Part Number 39795 54041 BL01-009 BL01-015 54181 64257 41159 41160 41052 41053 48264 48263 41151 48265 36900 37420 30723 * 52843 37127 37815 42431 16688 37128 41751 37129 42925 42620 44608 48845 43258 43262 37849 39215 PN01-016* PN01-107* LW01-004* 37044 41760 37231 42088 39180 37026 41154 41154 54011 41024 42844 41024 41761 41217 41101 41102 41145 41008 41009 37063 37064 Description Socket- Light Socket- Light - CE Light Bulb-120v-100w Light Bulb - 240v - 60w Heater - Upper Radiant - 240 v Heater - Upper Radiant - 208 v Decal - Control Panel - CM/CMT-7-Left Decal - Control Panel - CM-7-Right Decal - Control Panel - CM-5 - 0/S (single controls) Decal - Control Panel - CMT-5 - 0/S (single controls) Decal - Control Panel - CM-5 (dual controls) Decal - Control Panel - CMT-5 (dual controls) Decal - Control Panel - CMT-7-Right Decal - Control Panel - Self Serve - CM/CMT-5 PC Board Assembly - Display Plug for Probe Relay Probe- 5 ft. Bracket for Plug Receptacle Assy. - Probe - (Control Panel) Receptacle Assy. - Probe - (Uprights) Cooling Fan Gas Shock - 3 Pan (Before April 1, 1994) Gas Shock - 3 Pan Gas Shock - 5 Pail (Before April 1,1994) Gas Shock Gas Shock Assy. (CM/CMT-5 & CM-7) Gas Shock Assy. (CM/CMT-5 T&H only) Gas Shock - CMT-7 Cutting Board - 3 Pan Cutting Board - 5 Pan Power Cord Assembly - 5 Pan Power Cord Assembly - 7 Pan Clevis Pin Cotter Pin Lockwasher Hinge Cap (Before April 1, 1994) Hinge Cap Hinge Block Assy. (Before April 1, 1994) Hinge Block Assembly Hinge Block Assembly - Center - 7 Pan Hinge Pin Center Hinge Pin Hinge Pin CM/CMT-7 Tape - Acrylic Foam Crank - Steel - CM-5/7 (Before April 1, 1994) Crank - Steel - CM-5/7 Crank - Steel - CMT-5/7 (Before April 1,1994) Crank - Steel - CMT-5/7 Hinge Extrusion - LH - CM/CMT-7 Hinge Extrusion - RH - CM/CMT-5/7 Hinge Extrusion - RH - CM/CMT-5 Hinge Extrusion - RH - CM/CMT-7 Hinge Extrusion - LH - CM/CMT-5 Hinge Extrusion - LH - CM/CMT-5/7 Clamp Extrusion - CM/CMT-5 Clamp Extrusion - CM/CMT-7 *not shown Qty. Per Unit 5 7 10 14 10 14 10 14 10 14 5 7 5 7 1 1 1 1 1 1 1 1 1 2 2 3 2 4 1 3 1 3 1 1 2 2 1 1 2 2 2 1 1 1 1 1 1 1 1 1 2 1 1 1 3 3 3 3 3 3 3 3 3 3 2 2 2 2 1 2 2 2 1 1 2 2 2 4 2 4 4 4 4 4 2 1 1 1 2 1 1 1 1 Henny Penny CM/CMT-5/7 Service Parts List - Continued No. 45 46 46 47 47 48 48 49 51 52 52 52 53 53 53 53 54 54 55 55 56 56 56 57 58 59 60 61 61 62 62 62 63 64 65 66 67 67 67 67 68 69 70 71 72 73 *not shown C E Parts 46076 46209 48063 48064 48065 48066 48067 48068 48069 Part Number 41010 37130 41778 EF02-006 EF02-085 EF02-007 EF02-083 43768 37770 SC06-045* SC06-045* SC06-060* 37185 39025 39942 39968 39024 37183 42824 42819 39797 49420 55406 41041 36210* 29523* 54003* 41055* 41056* 38932* 46624* 43549* 44489* 41413* 37159* 37371* 42333 42340 43562 43563 23560* 22046* 55804* 55870* 55871* 51530* Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Qty. Per Unit Description Clamp Extrusion - CM/CMT-5/7 Pivot Support (Before April 1, 1994) Pivot Supports Fuse Holder - 15 Amp Fuse Holder - 20 Amp Fuse - 15 Amp Fuse - 20 Amp Power Switch2 PC Board - Output Shoulder Screw - CM-5/7 Shoulder Screw - CMT-5 Shoulder Screw - CMT-7 Lower Track - CM-5 Lower Track - CMT-7 Lower Track - CMT-5 Lower Track - CMT-7 Upper Track - CM/CMT-7 Upper Track - CM/CMT-5 Air Deflector - CM/CMT-7 Air Deflector - CM/CMT-5 Well Cover - 2" Flat Well Cover Well Cover- 3/8" Viewing Window - CM/CMT-5/7 Replaceable Beeper Probe - Temperature Legs Seal - Canopy Glass - 7 Pan (Before April 1, 1994) Seal - Canopy Glass - 5 Pan (Before April 1, 1994) Seal - Side Glass Seal - Side Glass - Huss. Seal - Side Glass - Tyler Seal - Middle Glass Viewing Window Bracket Pan Support - Long Pan - Cross Support Upright Stud Assy. - Left - 90° - D/D - Probe Guard Upright Stud Assy. - Rt. - 90°- D/D - Probe Guard Upright Stud Assy. - Rt. - 0/S-D/D - Tall - Probe Guard Upright Stud Assy. - Lt - 0/S-D/D - Tall - Probe Guard Infinite Switch Infinite Switch Knob Power Cord Assy- 30A 3 Ph Right Water Pan Support Bracket Left Water Pan Support Bracket Contactor- 3ph Albertsons Lamp holder Decal - Control Panel - HMT-5 Decal - Control Panel - HMT-3 Decal - Control Panel - HMT-3 Decal - Control Panel - HM-5 Decal - Control Panel - HM-7 Decal - Control Panel - HMT-7 Decal - Control Panel - CM-5 Decal - Control Panel - CMT-5 48070 48071 48072 48073 48074 48075 48078 48079 51058 51062 5 1 3 4 2 2 2 1 3 3 1 1 1 1 1 1 1 1 2 4 1 2 2 2 1 1 2 6 1 1 1 1 1 1 1 1 1 Decal - Control Panel - CM-7 Decal - Control Panel - CMT-7 Decal - Control Panel - HS-5 Decal - Control Panel - HST-5 Decal - Control Panel - HS-3 Decal - Control Panel - HST-3 Decal - Output Panel - HM 7 Decal - Output Panel - CM-7 Filter Board - HS/HST-3/5 Filter Board - HM/HMT/CM/CMT-3/5/7 7 1 4 2 2 2 2 2 1 1 1 1 1 1 1 1 1 2 2 4 1 2 2 2 1 1 4 10 1 1 1 1 1 1 1 1 1 1 Henny Penny No. 1A 1A 1A 1A 1A 1A 1A 1A 2 2 2 9 10 11 12 13 14 15 16 17 18 18 18 18 18 18 18 18 18 18 18 18 21 21 23 23 24 24 25 25 26 26 26 26 29 33 33 33 34 34 34 34 35 35 35 35 Part Number 54028 54125 54126 54038 54122 54123 54124 54121 38946 37972 37973 PL01-006* 18135 MS01-162 22609 22610 ME50-013 NS03-013 EF02-040 37230 37757 42969 43794 39938 42229 43791 42003 42230 43793 42009 42231 43792 37059 44976 39795 54041 BL01-009 BL01-015 54181 64257 39199 43017 41022 42245 30723 37128 42925 41751 43258 39181 43262 39840 43766 43767 37841 37849 Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HS/HST-3/5 Service Parts List Description Canopy Guard Assy. Complete - HST-3 Canopy Guard Assy. Complete - HST-3-Tyler Canopy Guard Assy. Complete - HST-3-Huss Canopy Guard Assy. Complete - HST-5 Canopy Guard Assy. Complete - HST-5-Tyler Canopy Guard Assy. Complete - HST-5-Huss Canopy Guard Assy. Complete - HS-3 Canopy Guard Assy. Complete - HS-5 Sliding Door Assembly - HST-3 Sliding Door Assembly - HS-3 Sliding Door Assembly - HS-5 Plug - Bottom End Clamp Mounting Channel .292 Terminal Block Barrier Spacer .250 TH, .281 LG, .171 I.D. Cage Nut Bushing - Snap Bracket - Drop Shelf Side Viewing Panel - HS-3/5 Side Viewing Panel - HS-3/5 (Mir)-Left Side Viewing Panel - HS-3/5 (Mir)-Right Side Viewing Panel - HST-3/5 Side Viewing Panel - HST-3/5 (Mir)-Left Side Viewing Panel - HST-3/5 (Mir)-Right Side Viewing Panel - HST-5-Huss. Side Viewing Panel - HST-5-Huss (Mir)-Left Side Viewing Panel - HST-5-Huss (Mir)-Right Side Viewing Panel - HST-5-Tyler Side Viewing Panel - HST-5-Tyler (Mir)-Left Side Viewing Panel - HST-5-Tyler (Mir)-Right Heater - Lower - 240 v Heater - Lower - 208 v Socket - Light Socket - Light - CE Light Bulb-120 V-100 W Light Bulb - 240 V - 60 W Heater - Upper Radiant - 240 v Heater - Upper Radiant - 208 v Decal - Control Panel - HS-3 Decal - Control Panel - HS-5 Decal - Control Panel - HST-3 Decal - Control Panel - HST-5 Relay - HS/HST-5 only Gas Shock (Before April 1,1994) Gas Shock - HS/HST-3 Gas Shock - HS/HST-5 Cutting Board - 3 Pan Cutting Board (Poly) - 3 Pan Cutting Board - 5 Pan Cutting Board (Poly) - 5 Pan Wire Grid - HS/HST-3 Wire Grid - HS/HST-5 Power Cord Assembly - 3 Pan Power Cord Assembly - 5 Pan Qty. Per Unit 3 5 1 1 1 1 1 1 1 1 2 2 2 1 1 2 2 3 3 1 1 2 2 4 4 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 2 3 6 10 6 10 6 10 6 10 3 5 3 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HS/HST-3/5 Service Parts List - Continued No. 36 37 37 38 39 39 40 40 41 42 43 43 43 43 44A 44A 45 45 46 46 47 48 49 52 53 53 53 53 54 54 56 56 56 56 56 56 56 57 57 60 61 61 62 62 64 64 65 66 66 68 68 69 70 71 71 72 73 Part Number PNOl-016* PN01-017* PN01-017* LW01-004* 37044 41760 37231 42088 41154 54011 41024 41024 42844 41761 37061 37062 37063 37064 37130 41778 EF02-007 EF02-006 43768 SC06-045 37184 37185 39961 39942 37182 37183 39185 42479 42477 42463 42413 46419 46420 39196 42253 54003* 41161* 41162* 41163* 41080* 41436* 42210* 41442* 42255* 41161* 37159* 37371 * 23560* 22045* 05863* 05864* 51058* 51530 Description Clevis Pin Cotter Pin - HS Cotter Pin - HST Lockwasher Hinge Cap (Before April 1, 1994) Hinge Cap Hinge Block Assy. (Before April 1, 1994) Hinge Block Assy. Hinge Pin Tape - Acrylic Foam Crank-HS (Before May 1, 1994) Crank-HST (Before April 1, 1994) Crank-HS Crank-HST Hinge Extrusion - HS/HST-3 Hinge Extrusion - HS/HST-5 Clamp Extrusion - HS/HST-3 Clamp Extrusion - HS/HST-5 Pivot Support (Before May 1 1994) Pivot Support Fuse Fuse Holder Power Switch Shoulder Screw Lower Track - HS-3 Lower Track - HS-5 Lower Track - HST-3 Lower Track - HST-5 Upper Track - HS/HST-3 Upper Track - HS/HST-5 Well Cover - HS/HST-3 (Bun Pans) Well Cover-3/8"- HS/HST-3 Well Cover-2". HS/HST-3 Well Cover-3/8"- HS/HST-5 Well Cover-2". HS/HST-5 Well Cover-Flat - HS-3 Well Cover-Flat - HS-5 Viewing Window - HS/HST-3 Viewing Window - HS/HST-5 Legs Seal-Canopy Glass (Before April 1, 1994) Seal- Side Glass - HS-3 Seal-Side Glass - HS-5 Seal-Side Glass - HST-3/5 Viewing Window Bracket - HS/HST-3 Viewing Window Bracket - HS/HST-5 Pan Insert Assy.-HS/HST - 3 (Before May 1, 1994) Seal-Front Viewing Glass - HS/HST-5 Seal-Front Viewing Glass - HS/HST-3 Pan Support-Long Pan-Cross Support Infinite Switch Infinite Switch Knob Sneeze Guard - HST-3 Sneeze Guard - HST-5 Filter Board - CE Contactor- 3ph Albertsons *not shown Qty. Per Unit 3 5 l l 2 2 1 1 2 2 2 2 2 2 2 2 2 2 2 2 1 2 4 4 2 2 4 4 2 2 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 1 2 2 2 2 2 2 1 1 1 1 1 2 4 6 10 1 2 1 2 1 1 1 1 1 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 LIGHT CANOPY ASSEMBLY Henny Penny Model CM/CMT.5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT.5/7 HM/HMT-3/5/7 HS/HST-3 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3