Download Bosch NES 730 UC Specifications
Transcript
NES 730 UC NES 930 UC Bosch Ceramic Glass Cooktops Models: NES 730 UC, NES 930 UC mnstaHation Instructions HodeHs: NES 730, NES 930 Table of Contents NOTE: Pages The blocked 2 & 4. klatch Overall letters, these junction Box Location and Clearances Cutout Cooktop Electrical 2, 3 D ............................................................................................. 2 Dimensions E .......................................................................... Countertop OWNER: Please Installations retain these H and | ................................................ instructions A A, Page 2. These dimensions are 4-5 NES 730 at 30 Amps; Model Connect only to a 4-wire 120/240 or 120/208 volt ac system. The neutral is required for the operation of this appliance required. and an independent ground Install box (not below supplied), is the counter top within 3 feet of flexible conduit (supplied) located at the left rear corner of the cooktop rough-in box. PAGE U BOX installation junction of the cooktop from the front Power Supply is dual rated: 240 Volts or 208 Volts, 4 wire, 60 Hz, with the following circuit breaker the owner. reference. mNSTRUCTmONS Plan the CONNECTION S mnspector's use. with this unit for future JUNCTION of the SUPPLY a junction for SAVE THESE DIMENSIONS requirements: Model NES 930 at 40 Amps 3-4 ................................................................................................... READ AND ELECTRICAL POWER FOR COOKTOP 3-4 O ...................................................................... Save these instructions for Local Electrical Please leave these Installation Instructions INSTALLER: 2 F ......................................................................................... to Countertop Connection iMPORTANT: POWER O .............................................................. the Cooktop Solid Surface See Illustration overall. pages. 2 Countertop OVERALL text on Supply B ............................................................................................................. Preparation Secure related to illustrations 2 Cabinet Installing to the below, refer A .................................................................................................. Dimensions Power such as A, shown of the box D LOCATION unit is within bottom. of the so that 3 feet It must cabinet. the of the be location left accessible rear mnstammationmnstructions Hodeb: OveraJJ Dimensions Mode[ NES 730:Width 30" Mode[ NES 930:Width 36" All Cabinet Power SuppJy Mode[ NES 730:30 Amp circuit breaker Mode[ NES 930:40 Amp circuit breaker All Models: Depth 2 [ - [/8" Height above countertop: Minimum Cabinet Required NES 730_ NES 930 240 Volt, 4 Wire, 208 Volt, 4 Wire, 1/4" Junction Clearances Box 60 Hz 60 Hz Location Bottom Wall EEl Building Back Wall II/'"i4 Zox Cooking Sut face Counter Top Cutout Dimensions 1" Flat Area I-3/4" 1" Flat Area 2-I/2' Setback (from front to]:_ to flont MODEL NO. Distance edge of co/rater edc_e of cutout ) CUTOUT DIMENSIONS* DIM. Minimum Inches / (mm) NES 730 NES 930 Flat Area Maximum Inches / (mm) B [9-7/8"/(505 C 28-3t4" B [ 9"7t8 '' t (505 mm) 20" t (508 mm) C 34-3/4"/ (883 mm) 34-7/8 '' / (886 mm) mm} 20" / (508 mm} t (73 [ mm} 28-7tB" t (734 mm) SFor solid surface countertop installations, use maximum cutout dimensions consult surface manufacturer for specific cutting instructions. PAGE 2 and installation Instructions HodeHs: NES 730, NES 930 CABINET PREPARATION CLEARANCES COUNTERTOP DiMENSiONS AND C The cutout CUTOUT dimensions depend upon To eliminate the risk of burns or fire by reaching installation is for over heated surface units, cabinet storage space located above the surface units should be installation in a solid surface countertop avoided, ff cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 in. (127 cutouts, use corners, Drawings ram) beyond the bottom Page 2. manufacturer of the cabinets. See C, This unit is designed for installation in the counter top with zero clearance to adjacent walls and proiecting surfaces constructed of combustible materials.A 30- as Sure[ , Corian ® etc,These TM of heat the bottom of the wood or metal cabinet is protected by not less than 1/4 inch of a flame retardant material covered with not less than No. 28 F1SG sheet steel, 0.015-inch (0.4 ram) thick stainless steel, 0.024-inch (0.6 ram) aluminum, or 0.020-inch (0.5 ram) thick copper. Flame retardant materials bear the mark: SWITCHED and back edge of the cooktop to the adjacent vertical combustible walls is zero inches. some guidelines installation the countertop instructions. THE COOKTOP Secure to sea[ the (see page 4),Turn tape off excess tape is provided approximately Use tape around the tape ends where Cooktop cooktop cooktop 1/16" entire edges upside from to down the glass glass perimeter cut butt. to countertop The cooktop should be secured to the countertop using the hold-down brackets provided. Prior to inserting cooktop into cutout, turn cooktop upside down and attach brackets to the burner box using the washers and screws. Place cooktop the brackets Use a wood materials, PAGE 3 larger rounded ON ACCIDENTALLY. foam tape apply edges, The minimum horizontal clearance from the sides and and or such TO AVOID ELECTRICAL SHOCK HAZARD, BEFORE iNSTALLiNG THE COOKTOP, SWITCH POWER OFF AT THE SERVICE PANEL AND LOCK THE PANEL TO PREVENT THE POWER FROM BEING the countertop flame spread ratings, the WARNING: A foam Followed by the flame spread and smoke ratings,these designations are shown as "FHC (Flame Spread)i (Smoke Developed):' [V[ateria[swith"O" flame spread ratings are flame retardant. Local codes may allow other require tape G and H provide INSTALUNG Sea[ with UNDERWRffERS LABORATORIES INC. CLASSIFIED MINERAL AND FIBER BOARDS SURFACE BURNING CHARACTERISTICS material materials reflective for specific whether new construction, only (see Page 4 and 5), Always consult inch minimum clearance is required between the top of the cool<top and the bottom of an unprotected cabinet. A 24-inch minimum distance is necessary when replacement, into cutout. and secure block Insert cooktop to protect clamping screws into to countertop, fragile countertop mnstammationmnstructions Foam Hodels: NES 730_ NES 930 Tape Seam Solid Surface Countertop mnstaHation Location of aluminum reflectivetape Installing Over An Oven 27}/8" / L: Coo!{top ConduitJ I L .Exposed edge must be a finish-cut 3J4"-_ 41' Nominal] Toe Space -J PAGE 4 mnstaHation Solid Instructions Surface HodeHs: NES 730, NES 930 ELECTRICAL Countertops Always consult manufacturer the for countertop specific Round 2. Apply heat cutout #425 it folds the outermost flange should be covered also Attach and brackets screws tape burner Use in the edge, (A light pencil edge and side Trim excess aluminum box beyond the All corners Connect the cooktop lead wires to the junction box supply wires in proper phase: all models, black, red neutral and connect (L 2) to green black red, wire white (L1) to wire to to ground. Electrical Code. tightening to ensure S. Test and of the cooktop from scratch the BIOTE: Your cooktop surface needs to be cleaned daily. Refer to the Use and Care section before using it for the first time. adequate of front counter will in the center.) along operation. block box and countertop of cooktop tape with the National as in 4. Turn on power supply. using washers before cutout notto the side marl< along the center edge box. Remove everything from the cooktop surface and apply Cooktop Cleaning Creme (packaged with cooktop) as directed in Use & Care blanuaJ, Page 9. @ and a wooden the burner aid in the positioning edges. BE CAREFUL Scotch tape. to the between 2, compliance to around top extends provided. cooktop the cool<top, with Center as or #427) of the countertop to the junction manufacturen (such over underneath the bracket screws. clearance S, tape Foil Tape Be sure according countertop reflective flexible conduit NOTE: If the cooktop is installed and connected specified above, it will be completely grounded corners the so that surfaces. 4, cutout from Aluminum 3, as follows: the instructions Attach For guidelines below and on pages 2-4 for preparing the cutout. I. I, instructions, Countertops made from natural (i.e. granite and marble) or SOLID SURFACE HATERIALS, such as Surell TM and Corian ®, require special cutout preparation and installation procedures. Follow the Install the cooktop CONNECTmON the frame the countertop, PAGE 5 mnstammationmnstructions HodeHs: NES 730_ NES 930 BEFORE CALLING If the elements power source do not See Use and Care data The data the center Keep your heat or if the indicator to see if a fuse has blown Refer to the Cooktop Product FOR SERVICE plate Vgarranty manual "on" or if the light circuit does breaker not gJow, check the has tripped. on Page 12 of the Use and Care Hanual. for troubleshooting information. plate shows front invoice the model and area of the rough-in or escrow papers serial box, for number of your underneath the warranty PAGE 6 validation cooktop. It is located cooktop. if service is needed. in Specifications are for pHanning purposes onHy. Refer to instaHHation instructions counter opening. ConsuHt with a heating and ventiHating engineer information, refer to InstaHHation Instructions accompanying product _A/e reserve the right to change specifications responsibHe for products which are transported or deaHer. For the most Note:The referred to throughout countertop suppHier prior or design without notice. Some modeHs are certified for use in Canada. from the United States for use in Canada. Check with your HocaHCanadian up to date criticaH instaHHation dimensions Bosch cooktop and consuHt your to making for your specific ventiHation requirements. For the most detaiHed or write BSH Home AppHiances Corp. indicating the modeH number. by fax, use your fax handset this manuaH is manufactured SSSH HcFadden and caHH702/833-3600. BSH is not distributor Use code #83 H7. by BSH Home AppHiances Corp. BSH Home AppHiances Corporation Avenue, Huntington Beach, CA 92649 o 800/944-2904 @ 2002 BSH Home AppHiances Corp. o Litho U. S. A. 50 60 00 3839 (8205)