Download Magnavox 26MF301B Service manual
Transcript
26” LCD TV chassis FL11.3 SERVICE MANUAL Contents TYPE A LC260EM2 EMERSON (Serial No.: DS1) LC260SS2 SYLVANIA (Serial No.: DS1) 26MF301B/F7 MAGNAVOX (Serial No.: DS1) 26MF301B/F7 MAGNAVOX (Serial No.: DS2) This service manual contains information of different types of models. Make sure to refer to the section describing your model. © 2011 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes. with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. 110414 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen. TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1 SPECIFICATIONS < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit --- MHz ±2.3 ±2.1 TV.ch.4 CA.ch.31 CA.ch.87 dBµ dBµ dBµ 18 18 18 20 20 23 Condition Unit Nominal Limit --- kHz --- ±100 ch.4 ch.10 ch.41 dBm dBm dBm ------- -76/0 -76/0 -76/+4 Description Condition Unit Nominal Limit 1. Native Pixel Resolution Horizontal Vertical pixels pixels 1366 768 ----- --- cd/m2 360 --- Horizontal Vertical ° ° -85 to 85 -80 to 80 ----- Condition Unit Nominal Limit Horizontal Vertical % % 5 5 5±5 5±5 --x y °K 12000 0.272 0.278 --±3% ±3% Horizontal Vertical line line 400 350 ----- 1. AFT Pull-In Range 2. Synchronizing Sens. < TUNER / ATSC > Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max) < LCD PANEL > 2. Brightness (w / filter) 3. Viewing Angle < VIDEO > Description 1. Over Scan 2. Color Temperature 3. Resolution (composite video) < AUDIO > All items are measured across 8 Ω load at speaker output terminal with L.P.F. Description Condition Unit Nominal Limit 1. Audio Output Vol. MAX (ATSC 0 dBfs) Lch/Rch W 10.0/10.0 9.0/9.0 2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0 -6dB: Lch -6dB: Rch Hz Hz 70 to 10 k 70 to 10 k ----- 3. Audio Freq. Response (NTSC) 1-1 FL11.3SP IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Safety Precautions for LCD TV Circuit d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test. 1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage. READING SHOULD NOT BE ABOVE 0.5 mA DEVICE BEING TESTED b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. LEAKAGE CURRENT TESTER _ + TEST ALL EXPOSED METAL SURFACES ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position. EARTH GROUND ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. 2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel. 2-1 LTVN_ISP 7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. 3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 2-2 LTVN_ISP Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it. I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet. L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly. 2-3 LTVN_ISP Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Chassis or Secondary Conductor Primary Circuit Table 1: Ratings for selected area AC Line Voltage Region Clearance Distance (d), (d’) 110 to 130 V U.S.A. or Canada ≥ 3.2 mm (0.126 inches) d' d Note: This table is unofficial and for reference only. Be sure to confirm the precise values. Fig. 1 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Exposed Accessible Part Z AC Voltmeter (High Impedance) Measuring Method: (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table. B Earth Ground Power Cord Plug Prongs Fig. 2 Table 2: Leakage current ratings for selected areas AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to: 110 to 130 V U.S.A. or Canada 0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible parts Note: This table is unofficial and for reference only. Be sure to confirm the precise values. 2-4 LTVN_ISP STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is indicated as shown. 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: Top View Out 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) Bottom View In Input 2. For other ICs, pin 1 and every fifth pin are indicated as shown. 5 Pin 1 10 3. The 1st pin of every male connector is indicated as shown. Fig. S-1-1 2. Remove the flat pack-IC with tweezers while applying the hot air. Pin 1 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Pb (Lead) Free Solder 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder. CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) Pb free mark 3-1 TVN_SN With Soldering Iron: 3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. CBA 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) Hot-air Flat Pack-IC Desoldering Machine Flat Pack-IC Desoldering Braid Soldering Iron Masking Tape Tweezers Flat Pack-IC Fig. S-1-3 2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) Fig. S-1-2 Sharp Pin Fine Tip Soldering Iron Fig. S-1-4 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) 3-2 TVN_SN With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Example : 5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Pin 1 of the Flat Pack-IC is indicated by a " " mark. Hot Air Blower or Fig. S-1-7 Presolder Iron Wire Soldering Iron To Solid Mounting Point Fig. S-1-5 Flat Pack-IC CBA CBA Fig. S-1-8 Fine Tip Soldering Iron Flat Pack-IC Tweezers Fig. S-1-6 3-3 TVN_SN Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. <Incorrect> CBA <Correct> Grounding Band 1MΩ CBA 1MΩ Conductive Sheet or Copper Plate 3-4 TVN_SN CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Step/ Loc. No. This flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were. [1] Stand Assembly [3] Digital Main CBA Unit [2] Rear Cabinet [4] Jack CBA [9] Speaker [5] Power Supply CBA [7] Inverter CBA [6] Stand Holder [10] Function CBA Part Fig. No. Removal Note [10] Function CBA 2(S-14), Shield Plate, D2 Sensor LED Lens, D3 Function Knob --- [11] Front Cabinet D2 --------------- --- ↓ (1) ↓ (2) ↓ (3) ↓ (5) ↓ (4) Note: (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures. (2) Parts to be removed or installed. [8] LCD Module Assembly (3) Fig. No. showing procedure of part location (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector e.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2) [11] Front Cabinet 2. Disassembly Method Step/ Loc. No. Part Fig. No. Removal Note (5) Refer to the following "Reference Notes in the Table." [1] Stand Assembly D1 4(S-1) --- [2] Rear Cabinet D1 11(S-2), 2(S-3) --- [3] 4(S-4), 3(S-5), 4(S-6), Digital Main D2 CN301, CN302, CBA Unit D3 CN3902, Shield Box, Jack Holder(D) --- [4] Jack CBA 3(S-7), (S-8), CL701A, D2 PCB Holder, D3 Jack Holder(A) --- [5] Power Supply CBA 8(S-9), CN101, D2 CN201, CN631, D3 CN801, CN802 --- [6] Stand Holder D2 2(S-10), 2(S-11) --- [7] Inverter CBA D2 6(S-12), CN1201, D3 CN1202, CN1203 --- [8] LCD Module Assembly D2 --------------- --- [9] Speaker D2 4(S-13), Hook, Speaker Holder(L,R) --- 4-1 FL11.3-A_DC (S-2) (S-2) (S-2) [2] Rear Cabinet (S-3) (S-2) (S-2) [1] Stand Assembly (S-1) Fig. D1 4-2 FL11.3-A_DC [11] Front Cabinet Shield Plate Sensor LED Lens (S-13) [3] Digital Main CBA Unit Hook Function Knob Jack Holder(D) [9] Speaker (S-13) (S-6) Shield Box (S-5) Speaker Holder(R) Hook (S-14) (S-4) [10] Function CBA [4] Jack CBA (S-5) [9] Speaker Speaker Holder(L) (S-4) (S-8) Jack Holder(A) (S-7) PCB Holder [8] LCD Module Assembly (S-9) (S-12) (S-10) (S-9) [7] Inverter CBA [5] Power Supply CBA (S-9) (S-11) (S-12) [6] Stand Holder Fig. D2 4-3 FL11.3-A_DC TV Cable Wiring Diagram To LCD Module Assembly To LCD Module Assembly Power Supply CBA Digital Main CBA Unit CN201 CN301 CN631 CN302 CN1201 CN3902 CN3701 CN3702 WH1001 CL701A CN1202 CN802 CN801 CN101 CL701B CN1203 To Speaker To Speaker Jack CBA Inverter CBA CL104B Function CBA Fig. D3 4-4 FL11.3-A_DC ELECTRICAL ADJUSTMENT INSTRUCTIONS How to set up the service mode: General Note: “CBA” is abbreviation for “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available. 1. Turn the power on. 2. Press [MENU] button to display Setup menu. 3. Select “Features”. 4. Select “Current Software Info”. 5. Press [0], [4], [2], [5], [7], [4] and [INFO] buttons on the remote control unit in this order. The following screen appears. Test Equipment Required 1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst) "*" differs depending on the models. Code : ******-***-*-***-**** Pic code : **-*******-***-*-*** 2. Remote control unit MIPS : Push 0 key 3. Color Analyzer Press "POWER" key to exit. Tuner : ****-*****-**** safety_Non Safety : HDMI EDID : OK 5-1 FL11.3EA 1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. Test Point Adj. Point 1. Enter the Service mode. Screen 2. Each time the [7] button on the remote control unit is pressed, the display changes as follows. [CH X/Y ] buttons M. EQ. Spec. Color analyzer See below Purity Check Mode Figure White mode To avoid interference from ambient light, this adjustment should be performed in a dark room. [7] button Perpendicularity [7] button Black mode L = 1.18 inches Color Analyzer [7] button Red mode 1. Operate the unit for more than 60 minutes. 2. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. [7] button Green mode 3. Enter the Service mode. 4. Press [3] button on the remote control unit. 5. Press [CH X/Y] buttons on the remote control unit so that the color analyzer value becomes minimum. [7] button Blue mode 6. To cancel or to exit from the VCOM Adjustment, press [CH RETURN] or [PREV CH] button. [7] button White 20% mode Note: When entering this mode, the default setting is White mode. 3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button. 5-2 FL11.3EA The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA. Purpose: To mix red and blue beams correctly for pure white. 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment. [DRIVE] Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment. Symptom of Misadjustment: White becomes bluish or reddish. 6. In each color mode, press [CH X/Y] buttons to adjust the values of color. Test Point Adj. Point 7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005). 3. White Balance Adjustment Screen [VOL Y] button Mode Input [VIDEO1] C/D White Raster (APL 70%) or (APL 40%) M. EQ. Spec. Pattern Generator, Color analyzer x= 0.272 ± 0.005 y= 0.278 ± 0.005 8. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button. Figure To avoid interference from ambient light, this adjustment should be performed in a dark room. Perpendicularity L = 1.18 inches Color Analyzer INPUT: WHITE 70%, 40% 1. Operate the unit for more than 60 minutes. 2. Input the White Raster(70%=70IRE, 40%=40IRE). INPUT SIGNAL 0IRE 0IRE Low Light Hight Light 100IRE 100IRE 40%=40IRE 70%=70IRE 3. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCDPanel surface. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. 4. Enter the Service mode. Press [VOL Y] button on the remote control unit and select “C/D” mode. 5-3 FL11.3EA HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure. 1. Turn the power on. 2. Enter the service mode. - To cancel the service mode, press [ ] button on the remote control unit. 3. Press [INFO] button on the remote control unit to initialize the LCD television. 4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed. 6-1 FL10.2INT FIRMWARE RENEWAL MODE Equipment Required The appearance shown in *1 is described as follows. Appearance a. USB storage device b. Remote Control Unit Firmware Update Procedure Note: There are two states (the User Upgrade and the Factory Upgrade) in firmware update. User Upgrade Upgrade the firmware only. The setting values are not initialized. Factory upgrade State Downloading... Downloading the firmware from the USB storage device. Writing... Writing the downloaded firmware in flash memory. Checking... Checking the new firmware. 5. When the firmware update is completed, the following will appear on the screen. Upgrade the firmware and initialize the setting values. Software Upgrade The identification of User Upgrade and Factory Upgrade are done by the filename. 1. Turn the power off and unplug the AC Cord. 2. Insert the USB storage device to the USB port as shown below. The software upgrade is completed. Remove USB storage device, turn TV off then on again. USB port Remove the USB storage device from the USB port. Turn the power off and turn the power on again. USB storage device Note: When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed. Rear Cabinet 3. Plug the AC cord in the wall outlet and turn the power on. 4. The update will start and the following will appear on the screen. "*" differs depending on the models. Software Upgrade Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Current Version: *******-***-*-***-**** New Version: *******-***-*-***-**** *1 Downloading... 0% Note: If the above screen isn’t displayed, repeat from step 1. 7-1 FL11.3FW TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. No Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Yes Is normal state restored when once unplugged power cord is plugged again several seconds? No Yes Is the INV+35V line voltage normal? No Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (C605, C606, D601, D602, D603, D604, Q601, Q602, T601) Yes Check each rectifying circuit of the secondary circuit and service it if defective. FLOW CHART NO.2 The fuse blows out. Check the presence that the primary component is leaking or shorted and service it if defective. Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective. After servicing, replace the fuse. FLOW CHART NO.3 When the output voltage fluctuates. Does the photocoupler circuit on the secondary side operate normally? No Check IC601, D652, Q631 and their periphery circuit, and service it if defective. Yes Check IC601, D609, D611 and their periphery, circuit and service it if defective. FLOW CHART NO.4 When buzz sound can be heard in the vicinity of power circuit. Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (IC631, Q209, Q210, Q211, Q213, Q635, Q636, Q637, Q640, Q641, Q642, Q643, D631, D632, D633, D634, D636, D638, D641, D642, D646, D647) FLOW CHART NO.5 INV+35V is not output. Is approximately +32V voltage supplied to the cathode of D636? No Check C638, D634, D636, D639 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit onthe loaded circuit, and service it if defective. 8-1 FL11.3TR FLOW CHART NO.6 LCD+24V is not output. Is approximately +30V voltage supplied to the collector of Q210? No See FLOW CHART No.5 <INV+35V is not output.> Yes Check Q207, Q208, D205, P-ON-H1 line and their periphery circuit, and service it if defective. FLOW CHART NO.7 LCD+13V is not output. Is approximately +15V voltage supplied to the collector of Q209? No Check C631, D631, D635 and their periphery circuit, and service it if defective. Yes Is approximately +14V voltage supplied to the base of Q209? No Check Q207, Q208, D203, D204, D211 and their periphery circuit, and service it if defective. Yes Replace Q209. FLOW CHART NO.8 P-ON+7V is not output. Is approximately +7V voltage supplied to the collector of D646? No Check C644, D646 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.9 P-ON+5V is not output. (LCD+13V is outputted normally.) Is approximately +7V voltage supplied to the collector of Q641? No See FLOW CHART No.8 <P-ON+7V is not output.> Yes Is approximately +6V voltage supplied to the base of Q641? No Check D645 and their periphery circuit, and service it if defective. Yes Replace Q641. 8-2 FL11.3TR FLOW CHART NO.10 TUNER+5V is not output. (LCD+13V is outputted normally.) Is approximately +6.7V voltage supplied to the collector of Q640? No See FLOW CHART No.8 <P-ON+7V is not output.> Yes Is approximately +6V voltage supplied to the base of Q640? No Check D645 and their periphery circuit, and service it if defective. Yes Replace Q640. FLOW CHART NO.11 AL+13V is not output. Is approximately +13V voltage supplied to the cathode of D641 and D642? No Check C639, D641, D642 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.12 P-ON+3V is not output. Is approximately +3V voltage supplied to the cathode of D647? No Check C645, D647 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.13 P-ON+3.3V is not output. Is approximately +5V voltage supplied to the cathode of D633? No Check C633, D633 and their periphery circuit, and service it if defective. Yes Is the "H" signal (approximately +4 V) inputted to the base of Q637? No Check Q638, Q639, D666, P-ON-H2 line and their periphery circuit, and service it if defective. Yes Replace Q637. 8-3 FL11.3TR FLOW CHART NO.14 P-ON+9V is not output. (LCD+13V is outputted normally.) Is approximately +13V voltage supplied to the collector of Q642? No See FLOW CHART No.11 <AL+13V is not output.> Yes Is approximately +10V voltage supplied to the base of Q642? No Check D670 and their periphery circuit, and service it if defective. Yes Replace Q642. FLOW CHART NO.15 AL+3.3V is not output. Is approximately +32V voltage supplied to the collector of Q635? No See FLOW CHART No.5 <INV+35V is not output.> Yes Is approximately +5V voltage supplied to Pin(3) of IC631? No Check Q635, D659 and their periphery circuit, and service it if defective. Yes Replace IC631. FLOW CHART NO.16 LCD-6V is not output. Is approximately -7V voltage supplied to the Anode of D632? No Check C632, D632 and their periphery circuit, and service it if defective. Yes Is approximately -6.5V voltage supplied to the base of Q211? No Check Q207, Q208, D208, P-ON-H1 line and their periphery circuit, and service it if defective. Yes Replace Q211. 8-4 FL11.3TR [ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Are the contact point and installation state of the key switches (SW101, SW103~SW107) normal? No Re-install the switches (SW101, SW103~SW107) correctly or replace the poor switch. Yes When pressing each switches (SW101, SW103~ SW107) do the voltage of Pin(29) of CN302 increase? No Check the switches (SW101, SW103~SW107) and their periphery circuit, and service it if defective. Yes Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. Operation is possible from the unit. Is 3.3V voltage supplied to Pin(2) terminal of the remote control receiver (RS102)? No Check AL+3.3V line and service it if defective. Yes No Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS102) when the infrared remote control is activated? Replace the remote control receiver(RS102) or the remote control unit. Yes Is the "L" pulse supplied to Pin(25) of CN301? No Yes Check the line between Pin(1) terminal of remote control receiver(RS102) and Pin(25) of CN301, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.3 Picture does not appear normally.(Video input) Are the video signal inputted to Pin(4) of CN302? No Yes Is the "H" level signal inputted to the Pin(5) of CN302? No Yes Check the line between Pin(4) of CN302 and JK752, and service it if defective. Check JK751, R763 and their periphery circuit, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. 8-5 FL11.3TR FLOW CHART NO.4 Picture does not appear normally.(Tuner input) Are the DIF signal inputted to the Pin(26,28) of CN302? No Yes Check the line between Pin(26, 28) of CN302 and TU301, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Are the video signal outputted to the Pin(6, 8) of CN302? No Check the line between Pin(6, 8) of CN302 and JK751, and service it if defective. Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y Yes Is the "L" level signal inputted to the Pin(5) of CN302? No Yes Is the "L" level signal inputted to the Pin(2) of CN701A? No Check CL701 and their periphery circuit, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. Replace JK751 FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Are the video signal inputted to the Pin(15, 17, 19) of CN302? No Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr Check the line between Pin(15, 17, 19) of CN302 and input terminals(JK731, JK732, JK733), and service it if defective. Yes Replace Digital Main CBA Unit or LCD Module Assembly. 8-6 FL11.3TR [ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Are the audio(L/R) signals inputted to Pin(2, 15) of IC771? No Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 8-7 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.3TR FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Are the audio(L/R) signals inputted to the Pin(4, 11) of IC771? No Check the line between Pin(4, 11) of IC771 and input terminal(JK741, JK742), and service it if defective. Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 8-8 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.3TR FLOW CHART NO.3 Audio is not outputted normally.(HDMI Audio input) Are the audio(L/R) signals inputted to Pin(5, 14) of IC771? No Check the line between Pin(5, 14) of IC771 and input terminal(JK721, JK722), and service it if defective. Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 8-9 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.3TR FLOW CHART NO.4 Audio is not outputted normally.(Tuner input) Are the DIF signals outputted to the Pin(26, 28) of CN302? No Check TU301 and their periphery circuit, and service it if defective. Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 8-10 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.3TR 9-1 SCK SI SO CS WP N2 CLKIN-32K N1 CLKOUT-32K X3102 32.768kHz OSC DIGITAL MAIN CBA UNIT U1 CLKIN-25M V1 CLKOUT-25M X3101 25MHz OSC SCK SIN SOUT CS WP K22 L19 L20 K21 F21 L2 L3 M2 M4 E19 C22 SCL1 K3 SDA1 K4 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ G19 INPUT0 G20 INPUT1 P5 AUDIO-MUTE 6 5 2 1 3 INPUT0 INPUT1 AUDIO-MUTE IC3101 (MEMORY) TO AUDIO BLOCK DIAGRAM 22 SCL 21 SDA CN3702 CN302 22 21 CN301 11 11 PROTECT1 15 PROTECT2 15 5 5 PROTECT3 29 29 VCOM-PWM 26 BACKLIGHT-SW 26 28 BACKLIGHT-ADJ 28 CN3701 CN301 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R CN3701 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R T1 R2 U3 P2 P3 CN302 29 CN3702 29 KEY-IN1 KEY-IN1 L1 IC3301 (MAIN MICRO CONTROLLER) P-ON-H2 P-ON-H1 PROTECT1 PROTECT2 DRIVE IC201,Q203, Q204,Q205 4 SCL 5 SDA * TU301 8 SCL 7 SDA (TUNER UNIT) REMOTE P-ON-H1 LED1 KEY-IN1 POWER SUPPLY CBA 10 VCOM CN201 KEY SWITCH D104 POWER AL+3.3V D105 STANDBY FUNCTION CBA LCD MODULE ASSEMBLY TO INVERTER BLOCK DIAGRAM (WH1001) CL104B 5 2 3 1 CN631 1 PROTECT3 2 BACKLIGHT-SW 3 BACKLIGHT-ADJ TO POWER SUPPLY BLOCK DIAGRAM * Either TU301 is used for Power Supply CBA. * TU301 (TUNER UNIT) Q171 Q172 CN101 2 5 4 6 REMOTE SENSOR RS102 1. System Control Block Diagram BLOCK DIAGRAMS FL11.3ABLS 9-2 Y JK731 COMPONENT -Y-IN JK732 COMPONENT -Pb-IN JK733 COMPONENT -Pr-IN JACK CBA C CL701B 5 3 1 2 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW DIF-OUT1 10 DIF-OUT2 11 IF-AGC 9 (TUNER UNIT) * TU301 DIF-OUT1 11 DIF-OUT2 12 IF-AGC 10 (TUNER UNIT) * Either TU301 is used for Power Supply CBA. * TU301 JK751 S-VIDEO -IN JK752 VIDEO-IN CL701A 5 3 1 2 POWER SUPPLY CBA WF4 WF2 WF5 WF3 WF6 WF1 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN CN302 26 DIF-OUT1 28 DIF-OUT2 24 IF-AGC CN302 4 6 8 5 15 17 19 CN3702 26 28 24 CN3702 4 6 8 5 15 17 19 DIGITAL MAIN CBA UNIT DIF-OUT1 DIF-OUT2 IF-AGC VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN AUDIO SIGNAL TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM VIDEO SIGNAL 2. Video Block Diagram FL11.3ABLV JACK CBA 9-3 Q873,Q874 DRIVE SP802 SPEAKER R-CH SP801 SPEAKER L-CH JK841 DIGITAL AUDIO-OUT (COAXIAL) CN801 SP(L)+ 2 SP(L)- 1 CN802 SP(R)+ 2 SP(R)- 1 CL801 CL802 BUFFER Q841 DRIVE2 35,36 31,32 PWM2 PWM1 POWER SUPPLY CBA 20 MUTE CONTROL DRIVE1 9,10 13,14 5 3 9 10 CONTROL LOGIC IC871 (OP AMP) 15 11 12 14 2 4 1 5 44 1 Q772 Q801 Q771 13 3 IC771 (AUDIO SELECTOR) IC801 (AUDIO AMP) 7 MUTE JK872 AUDIO(R)-OUT Q872 MUTE CL701A 7 9 1 Q871 CL701B 7 AUDIO(L)-IN 9 AUDIO(R)-IN JK871 AUDIO(L)-OUT JK721 HDMIAUDIO(L)-IN JK722 HDMIAUDIO(R)-IN JK741 COMPONENTAUDIO(L)-IN JK742 COMPONENTAUDIO(R)-IN JK753 AUDIO(L) -IN JK754 AUDIO(R) -IN WF7 AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT CN302 2 SPDIF 20 AUDIO-MUTE CN301 2 4 6 8 CN302 10 INPUT1 12 INPUT0 CN302 13 AUDIO(L) 11 AUDIO(R) CN3702 2 20 CN3701 2 4 6 8 CN3702 10 12 CN3702 13 11 8 7 6 5 8 7 6 5 35 36 33 37 34 DIGITAL MAIN CBA UNIT DSP 2 40 4 39 3 IC3803 (AUDIO DSP) LC260SS2(Serial No.:DS1), 26MF301B/F7(Serial No.:DS1,DS2) (L-CH) 15 D/A (R-CH) CONVERTER 14 IC3801 (D/A CONVERTER) (L-CH) 15 D/A (R-CH) CONVERTER 14 IC3802 (D/A CONVERTER) LC260EM2(Serial No.:DS1) LRCLK BCLK ADATA1 ACLK ADATA0 SPDIF AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT INPUT1 INPUT0 AUDIO-MUTE AUDIO(L) AUDIO(R) TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO SIGNAL 3. Audio Block Diagram FL11.3ABLA 9-4 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL 7 9 4 6 HDMI-IN2 1 3 10 12 16 15 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL JK3704 7 9 4 6 HDMI-IN3 1 3 10 12 16 15 57 56 60 59 63 62 54 53 51 52 8 7 11 10 14 13 5 4 1 2 42 41 45 44 48 47 39 38 36 37 HDMI SW 26 27 23 24 20 21 17 18 B5 A5 B6 A6 A3 A2 J19 J20 J22 J21 H20 C8 A/D CONVERTER P21 P22 N21 N22 M21 M22 L21 L22 VIDEO DECODER HDMI I/F AUDIO DECODER AUDIO I/F DEMODULATOR /MPEG DECODER SW IC3301 (DIGITAL SIGNAL PROCESS) R1 IF-AGC G22 S-VIDEO-SW H2 H1 F3 E2 F2 G3 E3 H3 K2 IC3702 (HDMI SW) AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT AUDIO(L) AUDIO(R) LRCLK BCLK ADATA1 ACLK ADATA0 SPDIF IF-AGC S-VIDEO-SW DIF-OUT1 DIF-OUT2 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL JK3702 7 9 4 6 1 HDMI-IN1 3 10 12 16 15 JK3701 TO AUDIO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DIGITAL MAIN CBA UNIT DIGITAL SIGNAL PROCESS TP POL CPV OE STV Y20,AA1-AA4,AA20-AA22, AB1-AB3,AB21,AB22 AA7,AA8-10,AA12,AA13, AA15,AA16,AB7-10,AB12, AB13,AB15,AB16 LVDS TX B9 A9 B10 A10 B11 A11 B12 A12 B13 A13 C12 C13 B8 A8 B22 D20 C20 A21 A20 B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, DATA(0-15) H1,H3,H7,H9 M2,M3,M7,M8, N2,N3,N7,N8, ADDESS(0-12) P2,P3,P7,P8,R2 IC3201 (DDR2 SDRAM) VIDEO SIGNAL CN3902 23 22 21 20 19 18 13 12 11 10 9 8 16 15 6 5 4 3 1 AUDIO SIGNAL LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) LLVCLK(+) LLVCLK(-) TP POL CPV OE1 STV LCD MODULE ASSEMBLY 4. Digital Signal Process Block Diagram FL11.3ABLD TO SYSTEM CONTROL BLOCK DIAGRAM (CN631) WH1001 BACKLIGHT-ADJ 9 BACKLIGHT-SW 10 PROTECT3 11 INV+35V Q1004 +5V REG. Q1008 Q1006 Q1009 Q1005 SW+5V Q1007 14 1 13 12 9-5 8 6 9 6 5 9 10 13 12 8 14 2 3 IC1001 (COMPARATOR) DRIVE2 DRIVE1 10 7 1 INVERTER CONTROL LOGIC 11 VDDA IC1101 (INVERTER CONTROLLER) INVERTER CBA SWITCHING Q1113 SWITCHING Q1112 SWITCHING Q1102 SWITCHING Q1101 INV+35V 8 7 6 5 1 4 6 5 2 3 T1203 1 4 2 3 8 7 6 5 1 4 T1202 8 7 2 3 T1201 CN1203 1 2 CN1202 1 2 CN1201 1 2 LCD MODULE ASSEMBLY BACK LIGHT BACK LIGHT BACK LIGHT 5. Inverter Block Diagram FL11.3ABLINV AC601 AC CORD LINE FILTER LINE FILTER 9-6 BRIDGE RECTIFIER D601- D604 POWER SUPPLY CBA Q601 SWITCHING Q602 SWITCHING CONTROL L602 L601 4A/125V F601 4A/125V HOT CIRCUIT. BE CAREFUL. FEED BACK Q631 16 15 14 13 12 11 10 9 4A/125V COLD 2 3 HOT 1 4 IC601 2 3 5 9 7 T601 CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Q635 +5V REG. Q634 Q209, Q213, D204 SW+16V Q207,Q208 SWITCHING Q210 SW+24.5V IC631 +3.3V REG. Q640 SW+5V Q638,Q639 SWITCHING Q641,643 SW+5V Q632, Q637, D666 SW+3.3V Q642 SW+9V Q401 Q201, Q202, Q212 SW Q211 SW-6.8V P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V LCD-6V LCD+13V P-ON+3.3V VGH CN3701 10 16 21,22 19,20 14 P-ON-H1 P-ON-H2 PROTECT1 PROTECT2 TO SYSTEM CONTROL BLOCK DIAGRAM P-ON+9V AL+33V P-ON+5V AL+13V TUNER+5V AL+3.3V P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V DIGITAL MAIN CBA UNIT LCD MODULE ASSEMBLY NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. CN301 10 16 21,22 19,20 14 CN201 8 2,3 6,7 4 CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 6. Power Supply Block Diagram FL11.3ABLP SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards. Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in µF (P = 10-6 µF). 5. All voltages are DC voltages unless otherwise specified. 6. This schematic diagrams are masterized version that should cover the entire FL11.3 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the FL11.3 chassis. Please refer to the parts lists for each models. 7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version. 10-1 FL11.3SC LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 3. Note: 1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.: 2 1 (Unit: Volt) 3 5.0 Voltage 5.0 Power on mode Indicates that the voltage is not consistent here. 5. How to read converged lines 1-D3 Distinction Area Line Number (1 to 3 digits) 3 AREA D3 2 Examples: 1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 1 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1". 1-B1 AREA B1 1-D3 A B C D 6. Test Point Information : Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin. The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function. 10-2 FL11.3SC Power Supply 1 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V HOT CIRCUIT. BE CAREFUL. 15.3 R253 Q213 4.7 2SA950-O (SW+13V) F601 4A/125V AC601 AC CORD R601 1.2M/1/2W (NO CONNECTION) CN601 AC120V 2 AC120V 1 4A 125V D631 FR154 C631 470/25V 13.1 14.8 14.8 R247 R227 2.7 3.3 /1/2W /1/2W D635 1ZB22BB SA601 SURGE ABSORBER C601 0.47/300V L601 LINE FILTER D620 1ZB220 -YBB R617 2.2/5W C691 3300P/250V R602 2.2/5W C692 OPEN D603 1N5406-BU L602 LINE FILTER D601 1N5406-BU D604 1N5406-BU JS603 OPEN JS604 OPEN D602 1N5406-BU JS601 OPEN JS602 OPEN C602 0.47/300V C603 OPEN C693 1000P/250V D636 SB3200BR D634 SB3200BR 3 10 6 D633 FR151-B/P 11 BC601 BEAD 5 13 3 14 15 2 R649 100K R646 220 31.6 4 30.5 C646 2200P/100V 2 6.3 Q631 KTC3198-Y-AT/P (FEED BACK) 3 R655 2.7K VIN IC631 LD1117V (+3.3V REG.) VOUT C612 0.068 /100V GND R615 3.9K C650 OPEN R242 12K R650 2.7K D652 HZS5.6NB2TE-EQ Q636 2SA950-O (+3.3V REG.) 3.4 1 2 3 2.1 3.4 5.1 5.1 5.2 R666 1 R632 1 R633 R636 3.3 3.3 /1/2W /1/2W R241 22K R668 620 D207 R238 220 R239 OPEN R690 OPEN D210 5V6BSB-T26 C652 1000/6.3V D414 D411 C683 0.1 D417 3V9BSB-T26 C682 0.1 R236 WIRE D205 C223 22/50V 24BSA-T26 D206 R237 8.2K D418 3V9BSB-T26 R700 OPEN R644 82K R647 75K D650 0.7 0 R662 15 D658 6V8BSA-T26 R665 WIRE 6.7 6.4 Q635 KTC3198-Y-AT/P (+5V REG.) R696 3.9/1W R697 3.3/1W D407 10BSB-T26 C648 100/10V R677 330 7.5 6.7 Q638 KTA1267-GR-AT/P (SWITCHING) D666 KIA431-AT/P R659 47K Q639 KTC3198 -Y-AT/P (SWITCHING) 0 C684 0.1 D421 R401 22K R679 3.6K C681 0.1 R680 10K R675 10K D665 WIRE D419 C647 OPEN D657 33BSB-T26 D412 D420 R658 10K CONTINUE POWER 4 LED1 REMOTE P-ON+9V AL+3.3V R687 100 13.8 D659 6V8BSA-T26 D662 FR154 D661 FR154 9.2 Q642 9.7 KTC3198-Y-AT/P (SW+9V) R688 WIRE R689 680 D670 10BSB-T26 D671 WIRE R407 22K C656 100/16V C657 22/50V R684 1.8 R682 R683 2.7 2.7 5.3 Q640 2SC2120-Y 6.0 (SW+5V) 5.3 Q643 R691 R693 7.0 2SA950-O 2.7 2.7 (SW+5V) 6.7 R406 OPEN D410 D664 OPEN CONTINUE POWER 2 AL+3.3V AL+13V PROTECT2 7.5 C653 220/10V R698 2.2 7.0 5.3 Q641 2SC2120-Y 6.0 (SW+5V) R641 1.1K R685 22 R642 10K R686 680 C655 OPEN COLD R402 22K D413 R676 47K C676 10/50V R661 220 /1/2W R660 680 R663 680 R664 680 R699 OPEN D401 OPEN R674 1K 0.2 0.7 Q634 KTC3198-Y-AT/P 0.1 (SWITCHING) 31.7 D660 R673 22K R634 2.7K R635 2.7K R637 2.7K D651 R652 820 R653 36K R656 R657 8.2 8.2 5.1 3.4 Q637 2SC210-Y 4.2 (SW+3.3V) R678 C651 WIRE OPEN R669 1K HOT R654 5.6K R404 47K Q210 KTC3198-Y-AT/P (SW+24V) 30.0 22.8 23.5 R235 330 -7.2 R672 2.7 /1/2W C641 OPEN D673 OPEN 1 -7.1 D209 36BSB-T26 7.5 IC601 TLP781F ERROR VOLTAGE DET D609 D610 OPEN C224 R244 2.2/50V OPEN 5.3 3.4 Q632 2SA950-O (SW+3.3V) 5.1 C639 1000/35V 5.7 D608 OPEN C645 3300/6.3V D641 SB390 D642 SB390 30.5 D612 39BSB-T26 R240 D208 47K 31.7 Q207 KTA1267-GR-AT/P 31.0 (SWITCHING) R223 R224 3.3k 27K R225 0.1 22K 0.7 Q208 R226 0 KTC3198-Y-AT/P 22K (SWITCHING) 31.7 C634 47/50V R243 150 Q211 KTC3198 -Y-AT/P (SW-6.8V) -6.5 D404 C632 100/25V 16 2 R614 0.27 /2W C402 3.3 OPEN -1.8 Q402 KTC3198-Y-AT/P 0 (RESET) C225 OPEN D405 R405 47K R403 27K R411 36K C638 D639 2200/35V 1ZB43BB 1 Q601 TK8A50D C609 134.5 D (SWITCHING) 0.1 R610 /100V R611 270 220 G 5.3 0.1 S R613 C610 5.3 D611 1.5K 1200P 0.5 /100V D607 0 4V3BSB-T26 D606 Q602 27BSB-T26 2SC2120-O SWITCHING R616 C611 270 CONTROL 560P 14.3 /2KV C613 1500P 0.5 /100V R234 2.2K D647 SB140 D632 FR104-B -0.7 Q401 KTC3198 -Y-AT/P (SWITCHING) D203 C633 2200/6.3V 12 BC602 BEAD R245 8.2K 2.7 0 D204 KIA431-AT/P R410 47K D638 FR154 9 7 D621 OPEN C644 3300 /10V D644 8V2BSB-T26 C642 1/50V C637 2200P/1KV C694 OPEN T601 POWER TRANS R604 0 R605 750K D211 D646 SB360BH R651 D643 1 FR104-B C606 270 /200V C222 R232 470/16V 9.1K R233 150 R231 C221 1.5K 0.01 R229 3.3K C604 OPEN C605 270 /200V R251 R250 6.8 6.8 13.1 Q209 2SC2120-Y (SW+13V) 13.8 R228 3.3K 4 R252 WIRE CONTINUE POWER 4 LCD+13V P-ON+3.3V LCD-6V LCD+24V CONTINUE POWER 4 AUDIO(R)-OUT AUDIO(L)-OUT LED-R CONTINUE POWER 2 AMP(R)-OUT AMP(L)-OUT TO DIGITAL MAIN CN301 CBA UNIT CN3701 3.3 1 P-ON-H2 2.3 2 AUDIO(L)-OUT 0 3 GND 2.3 4 AUDIO(R)-OUT 3.3 5 PROTECT3 2.6 6 AMP(L)-OUT 0 7 GND 2.6 8 AMP(R)-OUT 3.2 9 P-ON-H1 3.7 10 P-ON+3V 2.7 11 PROTECT1 0 12 GND 0 13 LED-R 5.3 14 P-ON+5V 0 15 PROTECT2 7.5 16 P-ON+7V 0 17 GND 0 18 GND 3.4 19 P-ON+3.3V 3.4 20 P-ON+3.3V 3.4 21 AL+3.3V 3.3 22 AL+3.3V 0 23 GND 0.4 24 OE2 3.3 25 REMOTE 3.4 26 BACKLIGHT-SW 0.6 27 LED1 0.9 28 BACKLIGHT-ADJ 1.6 29 VCOM-PWM CONTINUE POWER 4 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM-PWM OE2 P-ON-H1 LCD-P-SAFETY INV+35V D645 KIA431B-AT/P POWER SUPPLY CBA C654 220/10V R643 10K D415 CONTINUE POWER 3 P-ON+3.3V P-ON+9V P-ON+5V RESET CONTINUE POWER 2 AL+33V TUNER+5V UNLESS OTHERWISE SPECIFIED: DIODES ARE 1SS133. A B C D 10-3 E F FL11.3SCM1 Power Supply 2 Schematic Diagram VIDEO SIGNAL *Either TU301 is used for Power Supply CBA. *TU301 TUNER UNIT GND-1 +5V NU +32V NU AS SDA SCL NU IF-AGC DIF-OUT1 DIF-OUT2 GND CONTINUE POWER 1 AL+33V TUNER+5V 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 12 13 CONTINUE POWER 3 4 AUDIO SIGNAL TUNER UNIT GND NU NU SCL SDA +32V +5V NU IF-AGC DIF-OUT1 DIF-OUT2 *TU301 R303 100 R302 100 BC301 WIRE SCL SDA IF-AGC DIF-OUT2 DIF-OUT1 AUDIO-MUTE L301 33uH D301 C307 OPEN OPEN L304 OPEN C304 1000P D302 OPEN C306 C305 10/50V 0.1 C308 OPEN C310 47P L302 LK1608R22K-T R309 0 C311 47P L303 LK1608R22K-T R308 0 C303 330 /10V C302 0.1 R304 0 C309 0.1 CONTINUE POWER 1 AL+3.3V AL+13V PROTECT2 R819 22K 3 SP802 SPEAKER R-CH BC805 BEAD CN802 SP(R)- 1 SP(R)+ 2 CL802 C848 470P C845 OPEN C849 470P C846 OPEN D803 OPEN C823 OPEN C836 1 R815 10K C815 1 C837 2700P D805 OPEN D804 20BSB-T26 BC804 BEAD C821 0.1 BC801 BEAD C817 1 C816 10/50V R810 0 R816 3.3K C830 0.47 C828 0.1 C822 1000P L803 33uH C820 1 C829 0.1 L804 33uH C825 0.1 R811 OPEN C832 3.3/50V C826 1000P C833 0.1 R812 OPEN C824 1 C818 0.1 C819 10/50V D807 OPEN 3.6 0 3.6 4.2 13.6 19.1 13.6 13.6 6.4 6.4 0 0 6.5 6.5 13.6 13.6 19.1 9.3 5.1 5.4 0 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 GND GND 2 PWM2 RAMP GENERATOR DRIVE2 IC801 BD5426EFS-E2 (AUDIO AMP) CLOCK CONTROL PROTECTIONS & LOGIC PWM1 DRIVE1 MUTE CONTROL POWER LIMIT GND GND NU 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 3.6 5.1 2.1 2.1 3.6 19.1 13.6 13.6 6.5 6.5 0 0 6.5 6.5 13.6 13.6 19.1 0 0 7.7 C834 1 R813 10K C801 1 C835 2700P 1 R801 0 R803 11K R804 11K CONTINUE POWER 1 AMP(R)-OUT AMP(L)-OUT R802 27K R814 3.3K SP801 SPEAKER L-CH L801 33uH C804 0.1 C827 1000/25V C838 470P G C805 1000P L802 33uH C807 0.1 C811 0.47 H C839 470P R805 OPEN C808 1000P D801 20BSB-T26 D802 20BSB-T26 R806 4.7K C813 R809 OPEN OPEN 7.8 R820 7.8 Q802 22K 0.1 0 KTC3198 -Y-AT/P 0 (AUDIO-MUTE) 0 Q801 KTC3198 -Y-AT/P D806 (AUDIO-MUTE) 1SS133 C814 OPEN BC802 BEAD C809 0.1 R817 100K R808 OPEN R807 0 BC803 BEAD CN801 SP(L)- 1 SP(L)+ 2 CL801 C806 1 C803 1 C802 0.1 NU 22 R818 10K BC806 OPEN BC807 WIRE C847 0.1 C810 0.1 POWER SUPPLY CBA I J 10-4 K L FL11.3SCM2 Power Supply 3 & Jack Schematic Diagram POWER SUPPLY CBA BC841 BEAD R846 0 2.6 Q841 KTC3198-Y-AT/P (BUFFER) 5.3 4 2.0 JK841 DIGITAL AUDIO-OUT (COAXIAL) R844 220 C841 R842 0 1 R843 110 R841 OPEN R847 4.7K C843 0.01 C842 1 C844 10/16V R848 4.7K R845 OPEN R778 100K R713 OPEN R711 OPEN R712 OPEN 3 HDMIAUDIO(L)-IN HDMIAUDIO(R)-IN C704 OPEN C702 OPEN R716 OPEN D772 OPEN C776 100P R779 100K R792 OPEN R793 OPEN R794 OPEN IC771 TC4052BF(ELNF) (AUDIO SELECTOR) R791 OPEN R795 OPEN 1.1 1 4.6 2 VDD 16 9.2 15 4.6 4.6 3 4.2 4 14 0.2 13 4.6 0.2 5 0 6 INH 0 7 VEE 12 1.3 11 4.2 0 8 GND C723 2.2 R772 10K SW CTL R773 10K COMPONENTAUDIO(R)-IN CONTINUE POWER 4 KEY-IN1 AUDIO-MUTE R784 OPEN C743 2.2 C731 39P R731 OPEN C732 39P R732 OPEN C733 39P R733 OPEN JK732 JK733 COMPONENT -Pr-IN 9.2 R746 C742 39K OPEN R742 OPEN JK731 2 0 C744 2.2 R744 15K COMPONENT -Pb-IN C771 R771 100/16V BEAD C772 0.1 R763 10K 10 0 9 9.2 R745 C741 39K OPEN R741 OPEN COMPONENT -Y-IN C773 OPEN R783 OPEN R785 OPEN R786 OPEN R787 OPEN R777 C775 D771 100K 100P OPEN R726 C722 39K OPEN R743 15K JK742 R782 OPEN C724 2.2 R724 15K R722 OPEN JK741 R781 OPEN R776 100K 0 COMPONENTAUDIO(L)-IN R780 OPEN R725 C721 39K OPEN R721 OPEN JK722 R790 OPEN C701 OPEN R715 OPEN R723 15K JK721 R789 OPEN C703 OPEN R714 OPEN JK711 PC-AUDIO-IN R788 OPEN CONTINUE POWER 1 P-ON+3.3V P-ON+9V P-ON+5V RESET 0 R734 10 C734 0 R735 10 C735 0 R736 10 C736 0 R774 10K 0.7 Q771 KTC3198-Y-AT/P (INVERTER) R775 10K 0 Q772 KTC3198-Y-AT/P (INVERTER) WF1 WF3 WF2 WF7 WF4 WF5 WF6 JK751 S-VIDEO-IN C Y SW C751 OPEN R751 75 C752 OPEN R752 75 R756 0 C754 0 R757 0 C755 0 R758 0 JK752 1 VIDEO-IN C753 OPEN R759 15K R754 OPEN R760 15K R761 39K C761 OPEN JK754 R755 OPEN R762 39K C762 OPEN AUDIO(R)-IN C756 0 R753 75 JK753 AUDIO(L)-IN CL701B 1 2 3 4 5 6 7 8 9 S-VIDEO-Y-IN S-VIDEO-SW S-VIDEO-C-IN GND VIDEO-IN GND AUDIO(L)-IN GND AUDIO(R)-IN CL701A 1 2 3 4 5 6 7 8 9 CN302 0 1 1.7 2 0 3 0 4 3.4 5 0 6 0 7 0 8 0 9 3.4 10 4.5 11 0 12 4.5 13 0 14 0 15 0 16 0 17 0 18 0 19 0 20 3.5 21 3.5 22 3.3 23 3.2 24 0 25 0.6 26 0 27 0.2 28 3.3 29 TO DIGITAL MAIN CBA UNIT CN3702 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 CONTINUE POWER 2 SCL SDA IF-AGC DIF-OUT2 DIF-OUT1 AUDIO-MUTE C757 2.2 C758 2.2 JACK CBA M N O P 10-5 Q R FL11.3SCM3 Power Supply 4 Schematic Diagram AUDIO SIGNAL POWER SUPPLY CBA CONTINUE POWER 1 LCD+13V P-ON+3.3V LCD-6V LCD+24V R413 10K 4 R210 10 C201 0.1 C216 1000P 3 R412 47K C202 C203 0.1 0.1 IC201 TL3472CDR (COMPARATOR) R221 Q204 OPEN KTA1267-GR-AT/P 0 (V-COM DRIVE) R212 10 C218 1 3.0 VEE 1 2 3 4 0 0 0 0 0 C220 OPEN R220 1K 0.5 Q205 KTC3198-Y-AT/P (V-COM DRIVE) C209 OPEN R205 OPEN R204 2K JS202 R202 1K CONTINUE POWER 1 0.3 R201 100K C206 OPEN D202 1SS133 R249 OPEN C204 2.2/50V 0.4 1.0 0.4 R206 1K -0.9 C207 0.1 C873 2.2 R875 0 R173 OPEN IC871 NJM4558M(TE1) (OP AMP) Q171 KTC3198-Y-AT/P 0.8 (SWITCHING) 0 0 1 S T JK871 C871 3300P C880 100/16V R892 20K C876 270P R174 OPEN R871 560 R873 100K R877 1K C874 2.2 R172 22K CONTINUE POWER 3 KEY-IN1 AUDIO-MUTE 9.2 4.5 4.5 4.5 8 7 6 5 VCC GND 1 2 3 4 4.5 4.5 4.5 0 R876 0 R880 47K C885 2.2 R872 560 R874 100K C872 3300P 0 R886 100K R891 20K C875 270P Q872 KTC3198-Y-AT/P (AUDIO-MUTE) C883 2.2 R884 100K C878 6800P CONTINUE POWER 1 AUDIO(R)-OUT AUDIO(L)-OUT LED-R C882 2.2 R883 100K AUDIO(R) -OUT 0 -0.9 R882 100 R885 100K Q871 KTC3198-Y-AT/P (AUDIO-MUTE) JK872 R878 1K AUDIO(L) -OUT 0 -0.9 0 R881 100 R175 22K R893 22K Q212 KTC3198-Y-AT/P (SWITCHING) C879 0.1 Q172 KTC3198-Y-AT/P 0.1 (SWITCHING) 0.8 0 Q873 KTC3198-Y-AT/P 3.4 (SWITCHING) 0.1 0 Q874 KTA1267 -GR-AT/P (MUTE DRIVE) R248 10K L871 WIRE CN101 1 2 3 4 5 6 R887 22K R888 1K 3.4 R207 100K 0 LED1 REMOTE P-ON+9V AL+3.3V 3.4 22.8 Q201 KTA1267-GR-AT/P 22.2 (SWITCHING) Q202 KTC3198-Y-AT/P 20.0 (SWITCHING) TO INVERTER CBA WH1001 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ GND GND GND GND GND INV+35V INV+35V INV+35V R821 OPEN R203 OPEN C208 OPEN TO FUNCTION CBA CL104B GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 R222 OPEN CN631 1 2 3 4 5 6 7 8 9 10 11 R209 0 22.6 2 C213 OPEN R219 15K R216 10K C219 47/25V C212 OPEN Q206 OPEN R217 330 13.15.4 5.2 5.2 8 7 6 5 VCC C675 OPEN C210 22/50V JS201 OPEN 5.2 R214 0 CN201 1 0 2 13.1 3 13.1 4 22.7 5 0 6 3.4 7 3.4 8 -5.6 9 0 10 5.2 11 0 R218 10K R208 1 5.5 R215 OPEN TO LCD MODULE ASSEMBLY GND LCD+13V LCD+13V VGH GND P-ON+3.3V P-ON+3.3V LCD-6V GND VCOM GND C217 0.1 13.1 5.5 Q203 5.2 KTC3198-Y-AT/P R211 0 (V-COM DRIVE) R213 100K CONTINUE POWER 1 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM-PWM OE2 P-ON-H1 LCD-P-SAFETY INV+35V D422 1SS133 C877 6800P R879 47K C884 2.2 U V 10-6 W X FL11.3SCM4 Inverter Schematic Diagram INVERTER CBA C1023 470/35V 4 R1003 OPEN TO POWER SUPPLY CBA CN631 INV+35V INV+35V INV+35V GND GND GND GND GND BACKLIGHT-ADJ BACKLIGHT-SW PROTECT3 WH1001 1 2 3 4 5 6 7 8 9 10 11 R1004 2.7K /2W R1037 10K R1007 10K R1026 5.6K R1027 5.6K D1006 27BSB-T26 R1028 5.6K 14.2 Q1004 6.3 KTC3198-Y-AT/P D1001 5.6 (+5V REG.) 6V2BSB-T26 C1003 0.1 C1024 470/35V C1101 R1101 OPEN 5.1K D1101 5V6BSB-T26 31.9 30.1 D1111 G OPEN 15.7 D1104 1SS133 15.7 R1123 10 2.7 G 0 C1122 R1124 D1112 OPEN OPEN 2.2K C1123 0.047 R1029 10K C1002 100/35V Q1101 FDD5614P/Z (SWITCHING) C1132 OPEN D S C1121 R1122 OPEN 5.1K D1103 5V6BSB-T26 31.9 S 30.1 D1113 G OPEN 15.8 D 3 D1102 1SS133 R1102 10 C1102 OPEN R1030 20K 15.8 D 2.7 D1114 G 0 S OPEN R1103 2.2K R1116 10K R1005 4.7K R1016 0 R1006 0 R1117 110K R1018 1K R1013 4.7K 0 Q1009 KTC3198-Y-AT/P SWITCHING BACKLIGHT-ON C1006 0.22 1 3.3 0 0 Q1008 KTC3198-Y-AT/P (SWITCHING) A 0 R1024 10K C1107 0.1 C1022 OPEN R1119 30K D1202 1SS133 D1223 1SS133 R1230 33K R1224 100K C1204 OPEN C1215 1000P 3 7 1 6 4 5 D1217 1SS133 R1203 47K D1208 1SS133 R1220 30K D1203 1SS133 R1205 33K D1206 1SS133 R1204 47K D1204 1SS133 D1207 1SS133 R1206 33K R1218 100K C1109 0.047 CN1202 2 1 BACK LIGHT CN1203 2 1 BACK LIGHT D1221 1SS133 R1223 30K C1206 1000P D1205 1SS133 R1201 390 C1207 10P/6.3KV BACK LIGHT D1227 1SS133 C1208 1000P D1226 1SS133 D1218 1SS133 R1217 30K C1112 6800P R1120 1M C1209 10P/6.3KV R1215 100K IC1101 OZ9933GN-A-O-TR INVERTER CONTROLER T1203 INVERTER TRANS C1146 OPEN 2 8 R1121 5.1K R1137 56K C1213 1000P 3 7 1 6 4 5 C1210 1000P D1211 1SS133 R1207 390 D1212 1SS133 R1208 390 C1108 1000P R1209 47K D1214 1SS133 R1216 30K D1209 1SS133 R1211 33K R1210 47K D1210 1SS133 D1213 1SS133 R1212 33K R1214 100K C1211 10P/6.3KV D1225 1SS133 D1215 1SS133 LCD MODULE ASSEMBLY D1216 1SS133 R1213 30K C1212 1000P R1020 39K C1104 1000P R1022 8.2K D1004 1SS133 C1010 0.1 C1013 OPEN C1014 OPEN C1015 OPEN R1035 1K R1033 1K D1005 1SS133 C1110 2.2 IC1001 BA10324AF-E2 (COMPARATOR) R1019 22K C1011 0.22 C1116 4.7/50V C1021 10/50V 0 1.6 1.0 0 1.0 1.2 0 14 13 12 11 10 9 8 V- 1 0 R1023 10K D1003 1SS133 D1002 1SS133 B C1143 OPEN R1118 33K Q1006 KTC3198-Y-AT/P SWITCHING BACKLIGHT-ON R1025 10K R1228 47K R1202 390 0 0.7 T1202 INVERTER TRANS C1145 OPEN 8 2 ENA OVPT PWM ISEN VDDA TIMER PDR1 NDR1 C1007 R1012 0.1 4.7K R1009 4.7K 0 D1222 1SS133 C1205 10P/6.3KV R1219 100K C1115 1 Q1113 FD5612Z (SWITCHING) C1111 1000P JS1005 WIRE C1008 1000P 0.8 R1226 30K D1201 1SS133 R1229 33K C1106 1800P VSEN SSTCMP CT RT1 GND PDR2 GND NDR2 Q1005 KTA1267-GR-AT/P (SW+5V) 5.5 5.6 C1001 10/50V 4.9 C1214 1000P R1227 47K D1224 1SS133 R1222 390 C1142 OPEN C1113 1 C1114 1 Q1112 FDD5614P/Z (SWITCHING) 9 10 11 12 13 14 15 16 2.7 2.8 5.5 0 2.2 1.0 2.9 2.8 R1011 22K 5 Q1102 FD5612Z (SWITCHING) 2.7 0 2.8 0 1.3 1.3 0.3 1.6 8 7 6 5 4 3 2 1 JS1006 OPEN R1010 10K 6 4 C1202 OPEN D1220 1SS133 R1221 390 CN1201 1 2 R1138 0 R1017 4.7K 2.2 Q1007 0.2 KTC3198-Y-AT/P C1009 R1015 0 SWITCHING OPEN 22K BACKLIGHT-ON R1008 1K 7 1 D1219 1SS133 BC1203 BEAD C1203 10P/6.3KV C1103 0.047 2 3 C1005 0.1 C1004 100/10V R1014 10K S D T1201 INVERTER TRANS C1144 OPEN 2 8 C1131 OPEN C1201 10P/6.3KV R1225 BC1201 100K BEAD 2 3 2.5 0 V+ 4 5 5.5 0 6 7 1.6 0 C1017 OPEN C1012 0.1 R1034 1M C1020 R1036 0.01 1M R1031 1K R1032 1M R1021 18K C1019 0.01 C1018 0.01 C1016 0.1 C D 10-7 E F FL11.3SCINV Function Schematic Diagram C104 OPEN 2 R128 100 R125 OPEN R124 220 D105 L-53HT STANDBY R127 3.3K RS102 KSM-712TH2E (REMOTE SENSOR) R123 220 D104 333GT/E POWER C112 OPEN C110 OPEN VOUT Vcc GND CL104B 6 5 4 3 2 1 1 2 3 R126 1K C113 47/16V 1 D106 C114 OPEN C115 OPEN 330P C108 0.1 R116 18K R115 8.2K R114 4.7K R113 2.7K R111 4.7K R108 220 R109 10K SW107 VOL DOWN SW106 VOL UP SW105 MENU SW104 CH DOWN SW103 CH UP SW101 POWER TO POWER SUPPLY CBA CN101 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 D107 0.1 FUNCTION CBA UNLESS OTHERWISE SPECIFIED: SWITCHES ARE SKHHLMA010. A B C 10-8 FL11.3SCF Digital Main 1 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 5 OE2 BACKLIGHT-ADJ BACKLIGHT-ADJ(2) LCD+12V(1) DIGITAL MAIN CBA UNIT 4 (NO CONNECTION) +3.3V BUS-OPEN GND SDA SCL CN3903 1 2 3 4 5 8 C3901 OPEN 7 6 5 IC3752 OPEN C3903 OPEN 1 R3905 R3903 R3907 R3906 IC4202 OPEN 1 A0 VCC 8 2 A1 WP 7 3 A2 SCL 6 4 GND SDA 5 0 0 0 0 R3798 OPEN R3799 OPEN R3921 OPEN R3932 OPEN R3933 OPEN C3904 OPEN R3937 OPEN R3904 OPEN 2 4 R3838 OPEN R3800 OPEN C3786 OPEN 3 Q3751 OPEN R3912 OPEN R3913 OPEN R3909 OPEN R3916 OPEN R3951 OPEN R3934 OPEN R3902 OPEN NU E12 BACKLIGHT-ADJ C22 A 52 51 50 GND 53 VDDP 54 NU 55 49 C3911 OPEN 48 CONTROL SIGNAL GENERATOR 47 2 SERIAL INTERFACE 3 NU 46 4 NU 45 5 VDD-REG 44 6 GND 43 42 7 9 10 11 R3927 OPEN LVDS RX 37 36 14 35 15 34 16 33 C3924 OPEN LVDS RX 18 19 20 21 22 23 24 25 C3927 OPEN 26 C3910 OPEN R3910 R3908 R3918 R3911 R3923 R3922 R3924 R3925 R3926 R3938 R3901 820 B L3906 EXC24CG900U L3905 EXC24CG900U L3904 EXC24CG900U L3903 EXC24CG900U L3901 EXC24CG900U L3902 EXC24CG900U 38 13 17 EXC24CG900U 27 28 29 30 31 R3939 0 R3946 0 R3947 0 32 R3917 R3915 R3914 C3902 OPEN R3920 10K L3908 OPEN R3949 0 R3948 0 OPEN OPEN OPEN 0 0 0 0 0 0 0 0 0 0 OPEN OPEN OPEN 100P OPEN 100K OPEN 100K OPEN OPEN OPEN R3928 OPEN VDDM 39 DATA INPUT LATCH 12 L3907 GND R3929 OPEN 41 GND 40 GAMMA CORRECTOR FRC LINE BUFFER VDDL R3930 OPEN LVDS OUTPUT DATA PROCESSING 8 C3920 C3919 C3918 C3916 C3917 R3956 R3954 R3953 R3950 R3952 R3955 R3931 OPEN TO DIGITAL MAIN 2 IC3301(2/6) 1 56 PWMI 57 NU 58 PWMO OE2 59 1 R3919 OPEN C3921 OPEN *1 IC3301(1/6) ZR39745BGCG-2LGP0B DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER A8 B8 A14 B14 A9 B9 A10 B10 A11 B11 A12 B12 LVDS TX A13 B13 C13 C12 A15 B15 A16 B16 A17 B17 A18 B18 A19 B19 C19 C18 60 GND 61 NU 62 VDDIO R3935 OPEN R3936 OPEN VDDL 2 63 TEST 3 64 GND C3912 OPEN IC3901 OPEN C D 10-9 E CN3904 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO LCD MODULE ASSEMBLY LCD+12V LCD+12V LCD+12V LCD+12V LCD+12V GND GND GND LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) GND LLVCNK(+) LLVCLK(-) GND LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) GND TP POL CPV OE1 XA0 STV CN3902 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO LCD MODULE ASSEMBLY GND LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) GND LLVCNK(+) LLVCLK(-) GND LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) GND TP POL CPV OE1 XA0 STV CONTINUE DIGITAL 5 P-ON+3.3V CONTINUE DIGITAL 2 OE2 POL TP CPV OE STV RESET-LCD F FL11.3SCD1 Digital Main 2 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 5 P-ON+3.3V AL+3.3V C3013 0.01 R3137 4.7K R3002 47 C3059 OPEN L3002 C3004 0.22uH 33P 1 (NO CONNECTION) CN3104 CVBS-D0 1 CVBS-D1 2 CVBS-D2 3 CVBS-D3 4 GND 5 CVBS-D4 6 CVBS-D5 7 CVBS-D6 8 CVBS-D7 9 P-ON+5V 10 CVBS-CLK 11 GND 12 CVBS-START 13 CVBS-VAL 14 TO DIGITAL MAIN 3 IC3301(3/6) R3022 22 R3021 22 C3022 0.1 R3040 75 R3023 22 F3 NU G2 VCC 5 4 CONTINUE DIGITAL 5 AUDIO-MUTE KEY-IN1 LITE-SENS RESET C3740 1000P R3722 100 R3703 100 C3734 100P R3006 OPEN R3007 2.2K H3 G3 R1 IF-AGC SW C3006 1000P E3 K2 C3034 0.1 C3035 0.1 C3036 0.1 C3037 4700P C3046 33P C3045 33P R3033 10 R3026 0 C3047 33P R3032 10 D3705 EDZTE61 5.6B C3738 33P F22 RESET-LCD R3102 100 CN3702 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C3714 OPEN R3031 10 C3038 OPEN C3739 33P D3708 EDZTE61 5.6B C3736 1000P C3732 33P C3733 33P R3107 4.7K R3109 100 K1 G1 F1 E1 F21 WP P1 GPIO-P9 M4 VCOM-PWM R3160 100 C3042 OPEN R3030 C3039 C3040 C3041 100 100 100 100 A20 A21 C20 D19 C21 B22 D20 A22 B21 B20 F14 P3 R3 G22 CONTINUE DIGITAL 5 LED-R P-ON-H1 P-ON-H2 BACKLIGHT-SW REMOTE LED1 VCOM-PWM CONTINUE DIGITAL 4 SPI-WEN USB-EN R3793 0 R3142 OPEN STV OE CPV OE2 CPV2 TP POL NU NU NU NU LED-R POWER-CTL2 S-VIDEO-SW DIGITAL SIGNAL PROCESS C3731 100P R3719 100 CONTINUE DIGITAL 1 R3118 4.7K OE2 POL TP CPV OE STV RESET-LCD R3717 100 VGA-SCL T2 VGA-SDA T3 NU V5 D3712 EDZTE61 5.6B Q3853 OPEN R3853 OPEN R3851 OPEN C3726 33P C3741 1000P R3735 100 R3737 100 R3721 100 R3847 OPEN R3846 OPEN C3725 33P C3737 100P Q3704 OPEN TO DIGITAL TO DIGITAL MAIN 6 MAIN 1 IC3301(6/6) IC3301(1/6) C3728 33P C3727 33P R3848 OPEN C3787 OPEN R3839 OPEN D3706 OPEN R3736 OPEN C3730 100P R3742 0 TO POWER SUPPLY CBA CN302 KEY-IN1 DIF-OUT2 GND DIF-OUT1 GND IF-AGC RESET SCL SDA AUDIO-MUTE COM-VIDEO-Pr-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Y-IN GND AUDIO(L) INPUT0 AUDIO(R) INPUT1 GND S-VIDEO-Y-IN GND S-VIDEO-C-IN S-VIDEO-SW VIDEO-IN GND SPDIF GND CONTINUE DIGITAL 3 AUDIO(L) AUDIO(R) SPDIF P-ON+5V R3738 OPEN R3034 OPEN P2 P-ON-H1 U3 P-ON-H2 R3036 OPEN E19 BACKLIGHT-SW R3050 OPEN R3027 OPEN D3713 OPEN R3028 OPEN D3714 OPEN R3029 OPEN D3715 OPEN JK3703 D-SUB CONNECTOR R3038 OPEN G19 INPUT0 G20 INPUT1 T1 REMOTE R3037 OPEN R3049 OPEN R3850 100 C3729 33P D3711 EDZTE61 5.6B R3041 OPEN R3035 OPEN R3141 0 C3735 33P D3709 EDZTE61 5.6B R3718 100 VGA-VSYNC D1 VGA-HSYNC C1 R3042 OPEN R3942 R3943 R3944 R3940 D3710 EDZTE61 5.6B OPEN OPEN OPEN OPEN C3050 C3049 C3048 C3044 OPEN OPEN OPEN OPEN A/D CONVERTER R3945 100 R3941 100 1 R3724 100 R3723 100 R3720 100 H2 CONTINUE DIGITAL 3 CVBS-CLK CVBS-START CVBS-VAL 2 C3020 0.1 C3021 0.1 CONTINUE DIGITAL 3 RESET CONTINUE DIGITAL 4 SDA1 SCL1 C3003 15P C3060 OPEN 2 3 GND F2 E2 DEMODULATOR /MPEG DECODER C3002 15P IC3001 OPEN CONTINUE DIGITAL 6 HDMI-SEL0 HDMI-SEL1 3 H1 R3003 OPEN R3004 47 L3004 OPEN OPEN OPEN OPEN 75 75 75 R3140 OPEN R3043 R3044 R3045 R3046 R3047 R3048 4 (NO CONNECTION) CN3103 P-ON+3.3V 1 GPIO-P9 2 *1 IC3301(2/6) ZR39745BGCG-2LGP0B DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER J3 NU R2 LED1 H21 USB-EN E20 NU R3835 0.22 R3836 0.22 R3837 0.22 D3716 OPEN D3717 OPEN R3732 OPEN R3733 OPEN 11 6 1 12 7 2 13 8 3 14 9 4 15 10 5 D3703 OPEN Q3852 OPEN R3852 OPEN DIGITAL MAIN CBA UNIT G H I J 10-10 K L FL11.3SCD2 Digital Main 3 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. AUDIO SIGNAL DIGITAL MAIN CBA UNIT BC3801 BK1608HS601-T R3803 47K 16 15 *1 IC3301(3/6) ZR39745BGCG-2LGP0B DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 1 R3810 R3811 8 R3802 100 1 2 3 4 5 R3149 R3153 R3154 R4101 ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR SYSTEM CLOCK MANAGER SERIAL CONTROL PORT 9 NU 6 7 CONTINUE DIGITAL 4 EJTCK JTMS JTDO-M JTDI-M TRSTN CONTINUE DIGITAL 2 RESET R4102 OPEN 8 R4103 R4106 R4104 R4105 R3809 100 R3808 100 100 100 100 OPEN AUDIO SERIAL PORT CN4101 1 2 3 4 5 6 7 8 9 1K 4.7K 1K 1K (NO CONNECTION) VDD TRSTN ADATA1 EJTDO EJTMS EJTCK RESET RESET VSS OPEN OPEN R3805 100 R3814 OPEN R3812 OPEN 100 100 100 100 OPEN R3819 10K NU NU NU NU NU SPDIFO ADDR VDD NU NU PLLFIL VSS2 MODE 21 NU 22 ANATEST 23 SDAO 24 LDOPOFF 25 SCLO 26 REG15 27 MUTEXSPO 28 DVDDCORE 29 VSS1 30 DATAO2 31 RESETOX 32 SDAI 33 DATAO1 34 SCLI 35 MUTEX-DAC 36 BCKO 37 LRCKO 38 MUTEX-SP R3106 4.7K 39 RESETX 40 VSS3 OPEN 0.1 OPEN 0.1 OPEN 0.1 OPEN 0.1 7 12 11 10 GND VCC NU LPF DAC LPF DAC SYSCLKO C3054 C3015 C3053 C3016 C3062 C3023 C3052 C3017 6 13 4X/8X OVERSAMPLING DIGITAL FILTER /FUNCTION CONTROLLER ZERO DETECT AUDIO SERIAL PORT 14 R3807 47K R3813 OPEN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 R3833 0.22 R3834 0.22 IC3803 BU9414FV-E2 (AUDIO DSP) AGND G7 *A:H9~H15,J9~J15,K9~K15, L11~L15,M10~M15,N9~N15, P9~P14,E13,E14,Y9~Y15 CONTINUE DIGITAL 2 CVBS-CLK CVBS-START CVBS-VAL 1 NU E7 C3815 22/6.3V C3832 100P C3831 100P C3830 100P C3829 100P C3828 100P R3824 R3825 R3826 R3827 R3124 5 IC3802 PCM1782DBQR AUDIO D/A CONVERTER 15 R3806 47K C3804 10 SDATA2 B5 A5 B6 A6 *A GND SYSTEM CLOCK MANAGER 4 16 ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR R3801 100 R3828 33 R3829 33 R3830 33 R3831 33 R3832 33 R3134 0 ACLK J21 BCLK J20 LRCLK J19 H20 J22 DSP-RESET H19 NU E6 3 9 NU C3806 0.1 MCLK TO DIGITAL MAIN 6 IC3301(6/6) NU F6 2 BC3804 BK1608HS601-T C3812 0.1 NU F7 4X/8X OVERSAMPLING DIGITAL FILTER /FUNCTION CONTROLLER C3805 10 R3822 R3823 0 0 SDATA1 C8 AC-AVDD H6 AUDIO I/F 2 12 11 10 GND VCC NU LPF DAC LPF DAC SERIAL CONTROL PORT SPDIF TO DIGITAL MAIN 2 IC3301(2/6) 13 R3804 47K C3801 10 BCKI 3 ZERO DETECT 14 C3803 0.1 LRCKI NU NU NU NU NU NU NU NU GND IC3801 PCM1782DBQR AUDIO D/A CONVERTER C3055 10 C3056 10 A3 A2 B3 B2 C3 C2 A4 A1 B4 B1 D2 C3802 10 R3820 R3821 0 0 NU 4 CONTINUE DIGITAL 2 AUDIO(L) AUDIO(R) SPDIF P-ON+5V CONTINUE DIGITAL 5 P-ON+5V AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT BC3802 BK1608HS601-T CONTINUE DIGITAL 4 SDA0 SCL0 R3817 100 R3816 100 R3136 OPEN R3818 0 C3808 C3809 2.2 OPEN C3807 10 (NO CONNECTION) CN3101 P-ON+3.3V 1 CLK 2 R3815 1.5K C3811 0.027 N CONTINUE DIGITAL 6 SDA0 SCL0 BC3803 BK1608HS601-T C3301 OPEN CONTINUE DIGITAL 5 P-ON+3.3V R3111 4.7K M C3810 2700P O P 10-11 Q R FL11.3SCD3 Digital Main 4 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT L3401 0 4 C3403 C3404 C3405 C3406 C3407 C3408 C3409 C3410 C3411 C3412 C3413 C3414 C3415 C3416 C3417 C3418 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3 IC3201 K4T51163QG-HCF7 (DDR2 SDRAM) *B VDD C3420 0.1 1-U3 2-U3 3-U4 S0-DQ15 S0-DQ14 S0-DQ13 S0-DQ12 S0-DQ11 S0-DQ10 S0-DQ9 S0-DQ8 4-U3 5-U3 6-U4 S0-DQ7 S0-DQ6 S0-DQ5 S0-DQ4 S0-DQ3 S0-DQ2 S0-DQ1 S0-DQ0 L3402 OPEN R3409 OPEN C3401 0.1 C3419 0.1 VREF J2 CKE CK CK RAS CAS WE BA2/NU BA1 BA0 A12 A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ODT NU R3402 100 R3403 100 *1 IC3301(4/6) ZR39745BGCG-2LGP0B DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER R3407 100 C3402 0.1 C3421 10 K2 J8 K8 K7 L7 K3 L1 L3 L2 R2 P7 M2 P3 P8 P2 N7 N3 N8 N2 M7 M3 M8 K9 L8 E2 A2 R8 R7 R3 NU NU NU NU NU B7 A8 B3 B9 B1 D9 D1 D3 D7 C2 C8 F7 E8 F3 F9 F1 H9 H1 H3 H7 G2 G8 UDQS UDQS/NU UDM DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 LDQS LDQS/NU LDM DQ7 DQ6 DQ5 DQ4 DQ3 VSS *C DQ2 *B:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1 DQ1 *C:A3,A7,B2,B8,D2,D8,E3,E7, DQ0 F2,F8,H2,H8,J3,J7,N1,P9 R3408 R3410 OPEN 100 R3401 100 S0-DQ15 S0-DQ14 S0-DQ13 S0-DQ12 S0-DQ11 S0-DQ10 S0-DQ9 S0-DQ8 S0-DQ7 S0-DQ6 S0-DQ5 S0-DQ4 S0-DQ3 S0-DQ2 S0-DQ1 S0-DQ0 3-S4 6-S3 2-S4 1-S4 5-S3 4-S3 CONTINUE DIGITAL 2 SDA1 SCL1 2 CONTINUE DIGITAL 5 PROTECT5-USB IC3101 W25X32VSSIGE (MEMORY) 1 CS CONTINUE DIGITAL 2 SPI-WEN USB-EN R3138 4.7K VCC 8 2 SO NU 7 3 WP SCK 6 4 GND SI 5 C3107 0.1 R3121 1.8K 1 (USB JACK) USB+5V USB(-) USB(+) GND C3750 1 CN3704 1 2 3 4 Q3701 2SB1732TL (SW+5V) R3762 R3763 330 330 C3788 10 S C3774 R3774 OPEN OPEN R3761 10K Q3702 2SC4081UBTLQ (SWITCHING) T 4.7K R3126 4.7K R3122 1.8K R3760 10K R3770 1K C3775 R3775 OPEN OPEN R3135 R3764 10K C3724 1 R3765 15K C3752 OPEN IC3701 AS431AKTR-E1 SHUNT REGULATOR R3767 33K R3101 R3103 R3113 R3171 R3125 R3172 R3173 R3170 R3175 R3129 R3132 4.7K 4.7K 6.04K 100 4.7K 0 100 100 100 10K 10K R3130 R3131 4.7K 4.7K AA15 SO-DQ15 AA10 S0-DQ14 AA16 S0-DQ13 AA9 S0-DQ12 AB9 S0-DQ11 AB16 S0-DQ10 AB10 S0-DQ9 AB15 S0-DQ8 AA13 S0-DQ7 AA8 S0-DQ6 AB12 S0-DQ5 AA7 S0-DQ4 AB7 S0-DQ3 AA12 S0-DQ2 AB8 S0-DQ1 AB13 S0-DQ0 AA11 S0-UDM AB11 S0-LDM U13 S0-VREF AA14 S0-UDQSN AB14 S0-UDQS AA17 S0-LDQSN AB17 S0-LDQS AA19 S0-RASN AB20 S0-CASN AB6 S0-WEN AA18 S0-CKN AB18 S0-CK AA6 S0-CKE AB19 S0-ODT AB1 S0-A12 AA22 S0-A11 AA4 S0-A10 AA1 S0-A9 Y20 S0-A8 AA2 S0-A7 AB22 S0-A6 AB2 S0-A5 AA21 S0-A4 AA3 S0-A3 AB21 S0-A2 AB3 S0-A1 AA20 SO-A0 AA5 S0-BA2 AB4 S0-BA1 AB5 S0-BA0 Y22 USB(+) Y21 USB(-) D21 UART1-TX D22 UART-RX V20 NU K20 SPI-HOLD K19 SPI-SEL1 K21 CS K22 SCK L20 SOUT L19 SIN N3 TV-I2C-D N4 TV-I2C-C K4 SDA1 K3 SCL1 E22 SDA0 E21 SCL0 NU R15 NU V17 NU U17 RXD0 TXD0 NU NU U20 U19 T19 T20 R3404 R3405 R3406 CONTINUE DIGITAL 5 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V 60.4 60.4 150 R3120 100 R3119 100 R3115 4.7K R3114 OPEN R3165 4.7K R4107 R4108 C4101 0.1 EJTCK JTMS JTDO-M JTDI-M TRSTN R19 N20 P19 R20 N19 CN4102 1 2 3 4 (NO CONNECTION) P-ON+5V UART0-TX UART0-RX GND CONTINUE DIGITAL 3 EJTCK JTMS JTDO-M JTDI-M TRSTN R3117 100 R3116 100 CONTINUE DIGITAL 3 SDA0 SCL0 R3715 2.4 R3768 33K R3769 180 4.7K 4.7K CN3102 1 2 3 (NO CONNECTION) SCL0 GND SDA0 CN4103 1 2 3 4 (NO CONNECTION) P-ON+5V UARTSUB-TX UARTSUB-RX GND C4102 OPEN R3766 1.6 U V 10-12 W X FL11.3SCD4 Digital Main 5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. (NO CONNECTION) CN3703 AL+3.3V 1 INVALID-PROTECT2 DIGITAL MAIN CBA UNIT R3744 4.7K BC3004 BK1608HS601-T C3065 1000P C3066 0.01 S G CLK25M-VDD3V3 U9 AUDIO-MUTE P5 C3109 15P CONTINUE DIGITAL 1 P-ON+3.3V C3531 0.1 C3536 0.1 C3537 0.1 C3538 0.1 C3026 0.1 C3024 0.01 CLKIN-32K N2 CLKOUT-32K N1 KEY-IN1 L1 LITE-SENS M3 T9 SYSPLL-AVDD3V3 R3127 R3128 OPEN 220 X3101 C3108 25MHz 15P C3617 R3628 R3621 100 0.1 47K Q3607 2SC4081UB-TLQ (SWITCHING) C3104 R3104 C3102 15P 220 0.22 X3102 R3108 R3110 32.768KHz 1M 0 C3103 15P R3014 OPEN C3503 0.01 ADC9-RBIAS L4 AFE-RSET J2 VBAT M5 F13 HDMI-VDD3V3 C3506 0.01 CONTINUE DIGITAL 6 P-ON+3.3V(1) PROTECT1 PROTECT2 PROTECT3 PROTECT5-USB INVALID-PROTECT R3039 10K C3573 0.1 R3139 10K C3106 OPEN C3621 0.01 IC3103 PST8420UR (RESET) 1 GND OUT 4 2 VDD CD 3 C3116 0.015 L2 L3 M2 G21 H22 C3509 0.01 C3508 1000P BC3506 BK1608HS601-T C3507 0.01 C3502 1000P BC3013 BK1608HS601-T T10 CVDD-MSD P12 CVSS-MSD T17 DDRPLLVDD P1 DDRPLLVSS M17 HDMI-VDD1V C3025 OPEN C3030 1 C3028 0.01 C3027 OPEN C3029 1 C3051 0.01 BC3011 BK1608HS601-T AFE-FILT-OUT J1 AFE-VDD10-PLL N7 AFE-PLL-GND M9 AFE-VDD10-RGB0 AFE-VDD10-RGB1 AFE-GND0 AFE-GND1 K6 K7 L9 L10 C3574 3900P C3575 200P C3512 1000P C3514 1000P C3534 10 C3586 1 C3590 1 C3591 1 C3592 1 C3593 0.1 C3594 0.1 C3641 0.1 C3629 0.1 C3630 0.1 AFE-VDD3V3-RGB0 J6 AFE-VDD3V3-RGB1 J7 C3513 0.01 C3515 0.01 BC3505 BK1608HS601-T C3571 10 1 2 3 4 5 C3645 0.1 BC3504 BK1608HS601-T C3646 1000P C3647 0.01 BC3502 BK1608HS601-T C3504 1000P C3505 0.01 BC3005 BK1608HS601-T C3522 0.01 C3524 0.1 BC3006 BK1608HS601-T C3523 0.01 C3019 0.1 CORE-VDD-STB T7 R3610 10K C3541 10 MVDD *F C3533 10 C3532 10 C3530 10 C3549 1 C3551 1 C3555 0.1 C3556 0.1 C3557 0.1 C3511 OPEN 1 2 3 4 5 C3544 100/4V R3745 OPEN C3607 0.1 3 SW C3603 10 C3613 0.1 L3602 BEAD COMP 6 FB 5 C3608 10 C3609 10 Z R3706 100 C3713 1000P C3712 1000P R3864 22K C3751 100P C3710 100P C3708 10 C3706 0.1 C3709 10 C3711 0.1 C3748 10 C3749 0.1 C3701 10 R3709 100 C3719 1000P Q3601 OPEN R3713 100 C3605 1 R3603 6.8K C3606 0.015 R3615 3.9K Q3602 OPEN C3610 0.1 R3702 R3712 R3711 R3710 C3622 100/4V BB 10-13 C3720 1000P C3717 1000P CC R3777 OPEN CN3701 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 OPEN 11 10 9 8 7 6 5 4 3 2 1 TO POWER SUPPLY CBA CN301 VCOM-PWM BACKLIGHT-ADJ LED1 BACKLIGHT-SW REMOTE OE2 GND AL+3.3V AL+3.3V P-ON+3.3V P-ON+3.3V GND GND P-ON+7V PROTECT2 P-ON+5V LED-R GND PROTECT1 P-ON+3V P-ON-H1 AMP(R)-OUT GND AMP(L)-OUT PROTECT3 AUDIO(R)-OUT GND AUDIO(L)-OUT P-ON-H2 C3716 1000P C3620 OPEN R3602 6.8K AA C3707 0.1 R3863 C3703 10 C3705 0.1 R3604 OPEN R3606 OPEN R3601 47K Y R3862 OPEN C3602 10 R3605 OPEN EN 7 R3759 OPEN R3705 100 R3743 10K C3861 1000P C3643 10 L3601 10uH D3601 SK22A R3614 10K BC3601 BKP1608HS601-T R3616 IC3601 10K BD9321EFJ-E2 (DC-DC CONVERTER) C3601 0.1 1 BST SS 8 2 VIN R3861 OPEN R3609 1K C3619 OPEN 4 GND *D:E16,E17,F15~F17,P7,R7 *E:E9,F9~F11,H17,J17,K17,L17,U10 *F:U11,U14,U15,T11,T13~T15 R3608 1K R3607 510 C3644 10 C3604 0.1 C3721 1 C3639 0.1 C3611 10 C3612 0.1 C3722 1000P R3758 100 R3716 100 R3746 OPEN C3718 OPEN R3613 820 R3612 3.9K IC3602 BD7820FP-E2 (+1.8V REG.) C3640 10 R3617 OPEN C3583 0.01 IOVDD-STB U7 NU NU NU NU NU NU NU NU C3577 10 BC3501 BK1608HS601-T AFE-VDD33-REF L7 R21 R22 T21 T22 U21 U22 V21 V22 OPEN BC3503 BK1608HS601-T AFE-VDD33-PLL M7 *E CVDD C3535 10 C3715 1000P C3642 1 R3501 200K R3502 82K F12 LDI-VDDV3 C3539 10 R3623 OPEN R3626 22K R3611 10K 10K R3624 OPEN R3627 47K R3707 100 R3708 100 R3714 100 C3061 R3012 IC3603 0.1 100K BD7820FP-E2 (+1.8V REG.) D3101 1SS400 R3011 BC3507 BK1608HS601-T R3622 10K R3629 10K Q3605 2SC4081UB-TLQ (SWITCHING) G C3115 OPEN R3010 1 NU 4 Q3603 SSM3J321T S (SW+3.3V) C VDD33-BOD M1 C3101 0.01 R3618 OPEN D OUT D3501 1SS400 C3501 100/4V N17 LDI-VDD3V3 BC3010 BK1608HS601-T C3585 1 R3123 100 R17 DDRPLL-AVDD3V3 C3031 0.01 R3105 33K GND RESET-N W4 C3540 10 VCC C3584 0.1 C3510 100/4V C3114 0.01 C BC3001 BK1608HS601-T C3043 C3032 C3033 1 0.1 0.1 BC3012 BK1608HS601-T C3616 10 3 CE C3618 OPEN Q3606 2SC4081UB-TLQ (SWITCHING) R3625 OPEN C3615 0.1 2 GND CTL P17 USB2-VDDA33T C3105 0.1 C3614 10 R3620 47K R3013 OPEN BC3007 BK1608HS601-T 3 CLKOUT-25M V1 CLK32K-RTC N5 OUT BC3002 BK1608HS601-T C3526 1 GND C3543 1 C3527 10 VCC C3542 1 C3528 10 R3704 100 R3701 100 C3704 100P IC3604 MM3271BNRE (+1.0V REG.) 1 VDD VOUT 5 R3619 OPEN CLKIN-25M U1 *D IOVDD C3529 10 2 D C3067 1 CTL 4 Q3604 OPEN *1 IC3301(5/6) ZR39745BGCG-2LGP0B DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER CONTINUE DIGITAL 4 PROTECT5-USB CONTINUE DIGITAL 6 P-ON-H1 P-ON-H2 CONTINUE DIGITAL 2 LED-R P-ON-H1 P-ON-H2 BACKLIGHT-SW REMOTE LED1 VCOM-PWM CONTINUE DIGITAL 2 AUDIO-MUTE KEY-IN1 LITE-SENS RESET CONTINUE DIGITAL 4 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V CONTINUE DIGITAL 2 P-ON+3.3V AL+3.3V CONTINUE DIGITAL 6 P-ON+3.3V AL+3.3V CONTINUE DIGITAL 1 OE2 BACKLIGHT-ADJ BACKLIGHT-ADJ(2) LCD+12V(1) C3723 1000P 100 100 100 100 CONTINUE DIGITAL 3 P-ON+3.3V CONTINUE DIGITAL 3 P-ON+5V AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT C3702 1000P DD FL11.3SCD5 Digital Main 6 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into six and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 5 P-ON+3.3V AL+3.3V 4 L3701 BK1608HM102-T C3753 10 C3754 10 C3755 0.1 C3756 0.1 C3757 0.1 C3758 0.1 C3759 0.1 C3761 0.1 C3762 0.1 C3763 0.1 C3764 0.1 C3765 0.1 C3760 0.1 C3772 0.01 C3773 0.01 C3776 0.01 C3777 0.01 C3778 0.01 C3779 0.01 C3780 0.01 C3781 0.01 C3782 0.01 C3783 0.01 CONTINUE DIGITAL 5 P-ON+3.3V(1) *1 IC3301(6/6) ZR39745BGCG-2LGP0B DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER R3731 390 TO DIGITAL MAIN 2 IC3301(2/6) TO DIGITAL MAIN 3 IC3301(3/6) VIDEO DECODER AUDIO DECODER Q3703 2SK3018 (BUFFER) R3776 82K D3704 RB751S-40TE61 HDMI-REXT P20 HDMI-CEC U2 R3840 0 R3747 4.64K 16 R3734 27K L21 L22 M21 M22 N21 N22 P21 P22 HDMI I/F 3 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R3749 4.7K R3783 OPEN R3797 OPEN R3112 0 64 18 63 19 62 20 61 21 60 22 59 R3772 C3743 R3779 OPEN 0.1 0 R3784 OPEN R3729 47K R3854 0 58 57 HDMI SW 25 56 26 55 27 54 28 53 29 52 30 51 31 50 32 49 R3741 47K R3739 C3747 R3780 OPEN 0.1 0 R3785 OPEN R3855 0 R3750 C3785 C3784 OPEN OPEN 10K HDMI-SEL1 F20 R3133 0 R3730 47K IC3702 BU16027KV (HDMI SW) 17 24 R3782 OPEN HDMI-SEL0 F19 15 23 R3748 4.7K R3751 10K 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 R3786 OPEN 2 HDMI1-SCL HDMI1-SDA HDMI1-HPD HDMI1-5VSENSE W1 W2 W3 V2 R3755 R3752 OPEN HDMI2-SCL HDMI2-SDA HDMI2-HPD HDMI2-5VSENSE R4 R5 T5 U4 HDMI3-SCL HDMI3-SDA HDMI3-HPD HDMI3-5VSENSE V3 V4 P4 T4 0 C3767 0.1 R3787 R3788 R3795 R3756 0 0 0 0 R3794 R3791 R3792 R3789 R3790 R3796 R3757 0 0 0 0 0 0 0 R3725 10K R3754 OPEN C3768 0.1 IC3751 BU9883FV-W (HDMI SERIAL EEPROM) CONTINUE DIGITAL 2 HDMI-SEL0 HDMI-SEL1 CONTINUE DIGITAL 5 P-ON-H1 P-ON-H2 R3842 OPEN R3841 0 1 VCC1 VCC2 16 2 SCL1 SCL2 15 3 SDA1 SDA2 14 4 WPB R3781 OPEN C3771 0.1 CONTINUE DIGITAL 3 SDA0 SCL0 5 VCC-OUT 6 SDA0 FF D3701 EDZTE615.6B D3707 EDZTE615.6B R3726 10K C3744 0.1 JK3704 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 R3740 17 47K 18 19 R3844 1K JK3701 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 R3728 R3727 17 47K 47K 18 19 R3856 R3845 0 1K HDMICONNECTOR-2 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT HDMICONNECTOR-1 TMDS-D2(+) D-SHIELD0 TMDS-D2(-) TMDS-D1(+) D-SHIELD1 TMDS-D1(-) TMDS-D0(+) D-SHIELD2 TMDS-D0(-) TMDS-CLOCK(+) C-SHIELD0 TMDS-CLOCK(-) DVD-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT-PLUG-DETECT D3702 EDZTE615.6B SDA3 11 SCL3 10 VCC3 9 C3769 0.1 HH 10-14 C3746 0.1 R3843 1K NU 13 8 VCC0 GG R3771 10K C3745 R3778 0.1 0 HDMICONNECTOR-3 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT GND 12 7 SCL0 C3770 0.1 EE C3742 0.1 R3773 OPEN R3753 OPEN 1 JK3702 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 DIGITAL MAIN CBA UNIT II JJ FL11.3SCD6 Power Supply CBA & Jack CBA Top View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 4A/125V NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Power Supply CBA RESET-SW GND J336 P-ON-H1 GND J315 P-ON+5.0V J133 D301 2 D302 J145 RCV-IN LED1 J175 J173 CN301 28 29 PROTECT3 RESET J139 J140 1 GND 29 28 J343 D645 1 GND J349 C655 GND J347 GND GND LCD+15.8V GND D418 P-ON-H2 R656 R691 J248 J335 GND TU301 R693 D666 Q637 GND J334 GND J178 RCV-IN CN302 Q643 R698 +6.7V 2 J237 J350 R240 R684 +6.7V J177 LED1 GND GND J317 GND A-GND J324 J328 J307 ANA-A-L J114 Q871 R878 Q872 J169 ANA-A-R SEL-L R689 BC803 R175 ALL+3.3V JK752 CN801 D802 JK751 1 2 9 CL701B D 10-15 Jack CBA JK753 J153 D801 CN802 C J228 GND D671 D670 MUTEX J150 Q642 R687 L801 J108 SP+13V L802 J107 SP+13V D804 6 ERR/WARNING BC802 J151 ERR/WARNING D805 B Q171 J354 GND CL701A R688 J152 MUTEX BC805 Q172 C880 Q772 J163 INPUT0 Q771 J261 P-ON+9V R780 R781 J245 ALL+3.3V J351 GND RCV-IN J167 L871 V-L V-R J164 J165 R771 C656 LED-R FROM LED-R 1 JK754 BC804 10 R763 C844 Q874 J168 J117 HDMI-A-L J157 COM-L R788 SEL-L J166 R790 R791 J260 P-ON+9V J259 J357 GND D410 A-GND J147 MUTEX J149 J302 ERR/WARNING J209 VCCP2N J254 C657 TOOL NO. 1 2 3 4 5 6 7 8 9 D803 CN101 J135 P-ON-H1 J353 SP+13V SP+13V J130 SEL-R J132 SEL-L 9 GND J264 J265 J236 P-ON+3.3V P-ON+3.3V J352 GND J346 R601 SA601 C601 L601 C602 C832 BC807 02 L6 C604 C694 GND J120 SPDIF J266 J146 GND 2 1 C771 C816 J301 J344 AC601 JS601 LINE-FL-SHORT ALL+3.3V J355 A-GND A-GND J345 TM601 J244 D807 J210 BC801 VCCP2P D604 J342 A-GND 1 60 CN J115 HDMI-A-R MUTEX -6.7V J134 J138 Q801 C827 C814 C639 D641 R602 Q802 C823 PROTECT1 L804 TM602 LINE-FL-SHORT JS602 P-ON+3.3V J148 C819 L803 SP+13V J224 F601 4A/125V P-ON+3.3V R776 BC806 PC-A-IN A-MUTE J331 GND SP+13V BC841 Q841 J118 J136 J256 P-ON+5.0V ANA-A-R R660 R662 R821 J161 JS604 LINE-FL-SHORT J326 LCD+15.8V J263 RISK OF FIREREPLACEFH602FUSE AS MARKED FH601 J113 Q873 J246 LINE-FL-SHORT JS603 A-GND JK711 P-ON+3.3V GND J314 ERR/WARNING J262 P-ON+5.0V COM-L R819 A-MUTE D806 D602 J109 RCV-IN J267 JK841 J110 ANA-A-R J243 ALL+3.3V J249 D658 Q635 R663 D642 GND J112 Q636 D664 R632 D659 R664 D644 D601 S-SW JK732 JK871 JK872 J340 C648 D661 J339 J131 D660 D673 ALL+3.3V J218 D407 R407 J305 GND J238 R666 JK721 J111 J116 HDMI-A-L COM-L C644 D662 J306 GND 3 D64 COLD HOT D621 R617 R696 GND R665 HDMI-A-R JK722 J330 A-GND J329 A-GND R633 C642 J127 JK731 C676 J220 +6.7V J333 GND J332 GND P-ON+9V 11 C6 C606 JK733 SPDIF J158 AOUT-L PROTECT1 D646 D620 JK741 J129 AOUT-R J128 J312 JK742 IC631 R636 GND J154 R697 Operation GND J338 J322 J311 GND J327 J313 J160 Q638 J252 R672 +5.5Vfor3.3V +6.7V J215 GND Q639 C645 C633 GND J309 A-GND R674 R673 R616 C613 7 J308 J310 R678 Q632 J235 R677 C632 3 D63 C693 TU+32V J221 R683 R685 Q641 C654 R682 C652 D632 D64 C605 GND P-ON-H2 J141 L301 L304 D415 D413 J207 J233 R243 D417 J229 R657 J603 J356 P-ON+5.0V J304 PROTECT1 R686 R699 R700 P-ON+3.3V P-ON+3.3V BC602 D6 03 J143 GND C303 C306 J137 C210 P-ON+3.3V J239 Q601 C610 PROTECT1 J162 GND Q402 J255 VCOM J319 VCOM-PWM J253 LCD-6.8V J144 C675 VCOM SELECT C220 Q206 LCD-6.8V LCD-6.8V-SW J211 J106 J303 J142 P-ON+3.3V Q211 C631 C224 BC601 A AOUT-L J316 A-GND D657 R247 D639 91 POW-F/B J602 C650 D612 1 J124 P-ON+5.0V Q640 D611 D607 C612 D609 D210 R610 R611 1 AOUT-R LCD+15.8V J234 D209 D606 2 AMP-L J123 C653 +3.5Vfor1.8V C609 D608 AMP-R J125 J223 J208 +Vtune R613 3 J126 SDA J225 J119 PROTECT2 LCD+15.8V R210 GND SCL C647 R242 T601 R614 J122 J318 GND J226 J240 C6 C692 IC601 POW-HOT-CIR J601 D610 +Vtune Q204 Q203 R244 D631 R615 Q602 D635 J325 TUNER+5V J121 J227 +6.7V C634 D638 R655 J222 +3.5Vfor1.8V +36V P-ON-H1 J201 C222 J247 +6.7V R227 +15V J206 C638 J202 J219 D634 HOT GND R212 J230 R661 R646 R650 Q631 C646 D652 COLD BC301 J241 JS201 R250 D636 D650 J321 J320 LCD-6.8V J212 LCD+15.8V LCD+15.8V D204 R405 J242 J216 LCD-6.8V-SW C637 D665 +3.5Vfor1.8V D422 GND R251 R252 Q209 Q213 R229 R228 J203 J217 +36V Q201 D211 R245 C225 C204 GND D203 D208 J323 R223 R224 Q207 +36V D651 D404 C219 D401 R402 D412 R253 +36V Q634 4 D414 LCD-6.8V D420 D421 D411 PROTECT1 J250 J232 1 J337 J155 Q202 R203 R204 D202 R236 R239 R238 R237 C223 D205 J205 J341 GND GND D207 POW-SAFTY J101 J214 R235 J105 B/L-SW PROTECT3 J102 Q208 +6.7V B/L-ADJ J103 11 CN631 J156 J204 LCD+24V R249 11 J213 P-ON+3.3V D419 1 OE2 A 10 Q401 D405 J231 +6.7V BA01A0F0102 4 CN201 2 Q205 Q212 Q210 D206 A3 PROTECT3 J159 P-ON-H1 C7A3 JS202 CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. GND Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. E F BA01A0F0102 4 1 B G BA01A0F01024 Power Supply CBA & Jack CBA Bottom View P-ON-H1 C402 R412 R248 R201 C206 R202 J156 R203 Q202 D205 R237 C223 J102 J103 11 B/L-SW B/L-ADJ J101 +6.7V CN631 GND J214 POW-SAFTY J337 R223 R658 R659 C221 R231 1 R649 +36V Q634 R233 +15V J202 C646 C638 J206 +6.7V J247 R227 C222 LCD-6.8V J201 R232 D650 J211 LCD-6.8V-SW Q206 C220 R222 R221 C681 D413 R234 R637 R652 R635 R647 R634 R644 J205 J105 +36V Q207 R224 R229 R228 J323 D208 GND D203 C216 R213 R215 R214 JS201 R211 L301 L304 D415 C217 R208 R209 R309 L302 R304 4 C309 C305 C304 R700 R699 Q631 R650 R686 R683 R685 D652 R653 R646 C683 P-ON+3.3V P-ON+3.3V C682 28 J178 C634 RCV-IN CN302 D657 R679 C651 R680 J601 POW-F/B C631 R241 R656 P-ON-H2 D418 GND J350 GND J349 Q211 R642 R643 J602 POW-HOT-CIR IC601 C692 R240 R247 D639 R243 J207 J233 Q643 R641 2 1 GND GND D607 D610 D611 C612 Q602 D609 C613 +6.7V J252 3 R736 J220 +6.7V C676 C633 R669 R745 R741 R746 C744 J215 R672 C731 R732 C732 R733 COM-L C733 R742 J307 C743 C742 R744 C741 R743 Q638 +5.5Vfor3.3V Q639 C645 R674 R673 R616 R677 R676 J235 J310 J327 A-GND J311 A-GND J326 D606 R731 C736 J312 C735 R735 J324 J328 A-GND GND GND J317 GND R734 C734 C644 C610 R605 C684 Q636 R668 C724 R724 3 D64 R604 R651 D662 D661 D664 J243 ALL+3.3V D621 HOT COLD GND C703 D407 BC806 C814 Q802 C827 J138 J134 V-L C829 C822 C826 C825 C821 C828 J209 VCCP2N D604 P-ON+9V R785 V-R C775 BC807 C830 R811 C832 R772 R773 C604 60 1 R812 C833 C818 C817 J302 R816 R815 C837 SA601 R601 C693 C694 C602 BC805 L601 C601 C848 BC804 R807 R806 R805 C803 R804 J150 MUTEX D671 D670 JK754 R755 GND J356 D803 C846 C845 D804 C838 C758 C761 R761 C757 C762 C756 C754 C755 R762 D802 C805 C808 C807 C804 C810 C809 L802 C849 J107 SP+13V L801 C811 J108 SP+13V C839 R759 C753 JK752 R751 C751 R756 R753 JK753 R754 R758 R760 J153 ERR/WARNING R803 R802 C806 C802 R801 C801 R814 R813 C834 C835 J353 GND J352 GND ALL+3.3V J228 ALL+3.3V J245 R771 D410 C836 R810 C815 A-GND J147 MUTEX J149 R172 Q772 J163 INPUT0 Q771 J261 P-ON+9V R780 R781 R776 D771 J164 R777 J165 R784 J259 GND J357 ERR/WARNING C820 C824 J210 R817 BC801 VCCP2P L871 J167 R774 C880 R775 R892 C876 L6 02 C885 GND J354 R884 Q172 J160 R175 Q171 C878 C883 C874 R783 R787 C772 R782 J115 HDMI-A-R R794 R795 C776 R779 R786 J260 J166 R792 R793 C773 SEL-L C879 R174 R173 R886 R882 R880 J169 ANA-A-R IC871 C882 R883 C877 Q801 R809 MUTEX R808 -6.7V R818 C813 C641 C639 D641 R602 C823 R820 R789 R790 R791 D772 R411 R410 D642 R617 Q635 D658 R662 R660 R715 C701 R711 P-ON+9V R778 SEL-L R788 J117 J168 R891 R885 C842 R879 C875 D602 R881 HDMI-A-L J157 COM-L Q874 C884 R846 R847 C843 C844 R848 R887 R888 R893 R873 R875 C873 ANA-A-R R713 R876 R406 R407 GND D660 J305 C847 D673 C606 J306 C648 R714 C704 R712 R874 R716 C702 C722 R722 R872 Q872 R878 R871 R844 R842 C841 Q871 R877 J114 R845 J110 C872 J111 J116 COM-L R721 R725 J112 C721 R726 HDMI-A-L R723 HDMI-A-R C723 J113 ANA-A-R C871 R841 ANA-A-L R843 D620 R763 SP+13V RCV-IN 1 2 GND J341 R225 R226 D211 R252 R251 Q209 Q213 C202 C212 R218 R212 C210 C213 J137 C302 C310 R308 L303 C311 J221 TU+32V 29 J335 GND J224 PROTECT3 C640 R239 R238 R236 C225 C204 R245 Q201 C209 C208 R205 R207 J212 VCOM J255 C306 J140 C303 J348 R219 J203 +36V J217 LCD+15.8V LCD-6.8V Q205 R220 J144 R216 GND R217 C201 VCOM SELECT J321 C675 GND J320 R413 C203 J253 J319 R675 +3.5Vfor1.8V D419 Q402 GND J162 R404 R403 VCOM-PWM C218 LCD-6.8V D422 PROTECT3 R206 C207 J159 RESET-SW R654 GND J141 J143 J139 C307 D302 D301 2 J334 GND J161 D608 BC601 R757 R752 C752 BA01A0F01024 10-16 1 CN101 6 C605 C642 A B C D E R690 PROTECT1 P-ON-H2 RESET R302 J133 1 R687 D209 1 J265 Q210 PROTECT3 J173 J175 RCV-IN LED1 J145 P-ON+5.0V C308 J315 R303 GND 28 CN301 P-ON-H1 CN802 CL701B 9 1 R401 GND J336 29 JK751 D805 2 1 ERR/WARNING D801 Jack CBA F G Q642 BC803 CN801 J151 BC802 J152 MUTEX SP+13V 22 1 R688 AC601 J346 GND LINE-FL-SHORT JS602 J345 GND LINE-FL-SHORT JS603 FH602 SP+13V JS601 LINE-FL-SHORT J264 R689 SP+13V C657 GND CN 23 J344 J301 CL701A C656 GND J351 J342 A-GND IC801 R636 D634 2 D644 F601 4A/125V 44 A-GND R663 FH601 L804 C816 R664 JS604 LINE-FL-SHORT 9 1 L803 R665 D659 R632 Operation D6 03 A-GND J355 16 9 J146 FROM LED-R C771 PROTECT1 8 5 J135 D807 LED-R C819 J148 1 ALL+3.3V J254 J244 P-ON-H1 GND J331 8 IC771 GND D601 J263 P-ON+3.3V P-ON+3.3V J130 SEL-R J132 SEL-L J246 1 P-ON+3.3V 4 P-ON+3.3V J340 D806 J236 R633 J131 A-MUTE J262 P-ON+3.3V J118 R821 J136 PC-A-IN A-MUTE J266 J120 SPDIF R696 3 IC631 7 J603 R666 D646 J238 ALL+3.3V J249 ERR/WARNING Q841 J339 GND R819 J218 LCD+15.8V BC841 JK711 J256 JK721 JK872 JK732 JK871 JK841 Q873 P-ON+5.0V BC602 JK722 Q601 J330 A-GND J329 A-GND D63 J314 GND R611 D64 PROTECT1 11 C6 R697 J333 GND J332 GND C609 S-SW D612 P-ON+5.0V R614 R610 J154 JK742 J313 J128 AOUT-L JK741 R613 GND GND J322 J309 D635 R615 D632 J308 GND J127 JK733 JK731 J109 RCV-IN J267 WF1 PIN 4 OF CN302 Q632 T601 C632 R678 GND GND J338 J129 AOUT-R J158 SPDIF WF3 PIN 6 OF CN302 D207 D651 C637 HOT R242 Q637 J231 COLD D638 +3.5Vfor1.8V R655 C650 J219 +6.7V D631 R693 J239 C224 J237 +6.7V J248 LCD+15.8V C655 D645 J177 LED1 R698 TU301 C647 C6 91 R657 C652 +6.7V R684 R661 P-ON+3.3V R250 D636 J223 D210 D417 R682 J234 P-ON+3.3V J142 PROTECT1 D666 R691 J347 GND J343 GND J225 LCD+15.8V D204 R210 LCD+15.8V R244 J229 WF2 PIN 8 OF CN302 Q640 P-ON+5.0V J240 Q641 C654 Q203 J226 GND J318 J208 +Vtune LCD+15.8V GND J303 WF7 PIN 13 OF CN302 J106 J119 PROTECT2 J316 A-GND J304 GND LCD-6.8V-SW J124 R204 D202 R253 C653 AOUT-L WF4 PIN 15 OF CN302 P-ON+5.0V J216 Q204 J230 P-ON-H1 J123 SDA J121 J227 J125 J242 R249 LCD+24V +6.7V J122 OE2 R235 C219 SCL GND +Vtune AMP-L AOUT-R 8 5 D412 1 4 IC201 BC301 J232 J241 +3.5Vfor1.8V J222 TUNER+5V J325 +36V J126 WF5 PIN 17 OF CN302 AMP-R D404 Q212 JS202 Q208 R405 4A/125V D206 LCD-6.8V WF6 PIN 19 OF CN302 CN201 D405 J204 J155 PROTECT1 J250 D414 D665 J213 P-ON+3.3V D411 2 1 Q401 D420 D421 R402 10 11 D401 NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Power Supply CBA CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. J1081 GND J1066 J1067 GND 1 2 C1116 3 10-17 C1004 JS1006 Q1009 JS1005 R1037 ENA J1035 BL-SW J1043 BL-ADJ 11 4 WH1002 C1023 J1030 INV.31V R1028 R1027 R1026 11 R1003 J1000 INV-FB-2 C1143 INV-INPUT J1009 J1010 1 2 00 R1 J1059 GND C7A3 J1046 J1044 BC1201 A GND GND C1113 C1114 C1115 C1203 BA01A0F0103 2 INV-FB-1 C1214 J1002 J1001 FB-ISEN-1 R1004 J1076 J1075 J1003 R1122 FromNDR2 INV-FB-2 J1016 R1007 C1002 GND GND GND FromPDR2 J1019 Q1004 BC1203 D1001 D1006 J1039 SWfor+5V Q1005 J1077 FB-ISEN-2 CN1202 Q1008 J1031 BL-SW J1042 +5V C1001 D1102 D1103 Q1006 +5V J1041 PWM INV+5V NDR2 C1215 C1142 J1004 GND FB-ISEN-2 J1036 J1005 C1205 Q1007 J1060 J1065 FB-ISEN-3 INV-FB-3 J1006 GND GND GND C1207 PDR2 J1040 J1072 GND J1033 J1032 T1202 J1064 J1037 ISEN GND J1074 GND J1038 C1024 6 CL104A CN105 POWER C1022 GND J1073 PDR1 FB-ISEN-4 6 SW101 J1061 GND J1078 J1007 C108 D107 CL104B J1011 ALL3.3V 1 1 R126 Function CBA J1045 VSEN J1012 TIMER PDR2 GND CN1203 J1063 NDR1 INV-FB-4 R108 J1062 J1068 J1008 R111 GND R113 D1104 C113 R128 R114 J1049 +5V J1079 GND J1070 R109 R127 R123 D104 NDR2 J1047 C1021 FromNDR1 GND J1071 C1209 J1057 D1219 GND C1132 A3 J1048 +5V D1227 C1202 J1025 J1027 D1101 R1101 C1211 FB-ISEN-1 D1221 GND FromPDR1 R125 D1220 J1015 R124 D1224 D1223 INV-FB-5 C1131 D105 J1020 D1222 J1017 J1013 T1203 J1018 INV-FB-3 B FB-ISEN-5 J1014 SW103 D1202 D1201 FB-ISEN-3 J1023 INV-FB-4 J1022 STD BY C1204 D1226 C1206 D1217 D1218 CH UP INV-FB-1 FBforVSEN D1205 C7A3 J1050 J1051 C1208 FB-ISEN-4 D1208 B J1058 D1005 D1206 CH DOWN +5V GND J1021 SW104 J1052 D1003 D1207 MENU D1004 D1225 INV-FB-3 SW105 J1054 C J1053 ForProtect3 J1056 D1204 VOL UP J1029 INV-FB-5 D1203 R115 D1002 C1210 SW106 D1215 FB-ISEN-5 D1216 R116 VREF J1026 D1211 SW107 J1028 GND FB-ISEN-6 D1214 GND J1024 GND GND VOL DOWN D1212 D1213 J1080 J1069 BA01A0F0103 2 J1055 GND A D1209 D1210 C1212 Inverter CBA & Function CBA Top View Not Used POWER RS102 CN1201 C1201 INV-INPUT T1201 GND J1034 WH1001 A3 1 CN1001 1 11 5 Inverter CBA Not Used BA01A0F01032 Inverter CBA & Function CBA Bottom View Function CBA C108 R123 6 6 CL104A CN105 C113 R128 R109 R127 C104 R113 D107 J1011 ALL3.3V C114 C115 D106 C110 C112 C CL104B 1 R126 1 C1115 J1069 J1080 J1013 FB-ISEN-5 J1014 R1101 C1101 GND C1212 D1209 D1210 R1209 D1213 D1212 FB-ISEN-3 R1210 C1202 GND R1211 R1212 R1208 R1207 R1021 C1016 R1213 C1017 R1216 R1215 C1210 R1205 VREF R1020 R1206 C1015 R1221 R1225 R1222 R1230 R1229 R1019 R1032 R1226 GND IC1001 J1054 +5V J1047 R1013 R1012 C1112 J1081 GND J1066 R1005 R1006 R1035 C1013 R1036 C1019 C1014 R1033 C1020 R1034 J1052 J1053 ForProtect3 J1055 C1010 R1022 C1012 D1002 PDR2 R1018 Q1008 R1138 J1049 J1045 VSEN J1060 R1017 J1061 C1022 C1109 R1117 C1106 J1012 TIMER PDR2 NDR2 J1048 R1116 +5V J1058 J1050 R1023 J1051 +5V D1004 J1067 Q1007 R1015 R1024 R1025 C1011 R1014 J1031 BL-SW INV+5V +5V R1120 C1007 C1001 JS1005 Q1006 C1009 R1011 C1006 R1030 NDR2 R1016 INV-FB-1 FBforVSEN C1018 R1031 R1118 IC1101 C1107 GND J1078 C1123 GND J1073 C1204 1 JS1006 Q1009 C1004 C1005 D1001 R1037 R1029 R1010 R1220 C1208 C1206 R1201 R1217 R1218 INV-FB-3 R1202 R1214 R1204 R1228 D1222 R1224 R1223 J1068 NDR1 J1062 J1063 PDR1 C1110 C1104 R1119 GND J1072 C1103 D1102 C1102 R1102 R1103 Q1005 D1006 J1039 SWfor+5V R1008 R1009 D1225 R1121 J1037 ISEN C1108 C1111 R1137 C1008 R1124 J1079 J1020 D1220 D1224 D1223 D1202 R1227 D1217 D1218 D1205 J1023 INV-FB-4 J1022 J1057 J1038 GND GND J1074 J1077 J1065 J1064 J1033 J1032 D1104 C1122 GND R1123 D1219 FB-ISEN-1 D1221 J1015 J1018 INV-FB-3 J1071 J1070 FromNDR1 C1024 GND GND GND GND J1036 FB-ISEN-2 C1215 J1019 GND GND GND FromPDR2 R1122 C1121 J1003 J1075 J1076 FromNDR2 INV-FB-2 J1016 Q1004 R1028 R1027 R1026 J1030 INV.31V R1007 C1023 R1219 D1201 J1021 FB-ISEN-4 D1208 D1206 D1207 D1204 R1203 INV-FB-5 J1029 D1203 D1215 FB-ISEN-5 J1028 D1216 D1211 J1024 FB-ISEN-6 D1214 C1213 GND J1027 FromPDR1 GND GND GND D1112 J1008 J1007 J1006 J1005 J1004 D1114 J1001 J1002 R1004 J1056 GND GND C1146 C1131 INV-FB-5 D1111 C1132 INV-FB-4 FB-ISEN-4 C1145 FB-ISEN-3 INV-FB-3 INV-FB-2 FB-ISEN-1 C1142 D1113 C1143 FB-ISEN-2 C1144 J1026 C1214 A D1003 BA01A0F01032 10-18 D1005 14 J1025 INV-FB-1 Not Used Inverter CBA 8 1 2 3 4 5 B J1000 C1003 11 D1226 GND 1 C1116 11 GND R1003 C1002 CN1001 WH1002 1 D1227 7 C1021 J1042 +5V J1017 D1103 D1101 VOL DOWN MENU R111 POWER SW107 SW106 SW105 SW104 R116 R115 R114 VOL UP CH DOWN CH UP GND 8 1 J1035 BL-SW J1043 BL-ADJ 11 1 J1041 PWM J1034 WH1001 BC1203 9 J1059 INV-INPUT 16 ENA J1040 GND J1010 BC1201 J1044 J1046 GND C1114 C1113 GND GND R1 00 2 J1009 Q1101 Q1102 D105 D104 T1203 T1202 T1201 Q1112 Q1113 INV-INPUT CN1203 CN1202 CN1201 STD BY POWER SW103 R124 R125 R108 SW101 C1211 C1209 C1207 C1205 C1203 C1201 RS102 Not Used H.V. CAUTION WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) WF1 Pin 4 of CN302 CVBS WF2 0.2V WF6 20µs 20 0.2V 20µs 20 AUDIO 0.2V 20µs 20 Pin 19 of CN302 VIDEO-Pr WF7 0.2V Pin 17 of CN302 VIDEO-Pb Pin 6 of CN302 S-VIDEO-C WF4 20µs 20 Pin 8 of CN302 S-VIDEO-Y WF3 WF5 0.2V 20µs 20 Pin 13 of CN302 0.1V 0.5ms 0.5m Pin 15 of CN302 VIDEO-Y 0.2V 20µs 20 11-1 FL11.3WF 12-1 AC601 AC CORD AUDIO(R) -OUT AUDIO(L) -OUT DIGITAL AUDIO-OUT (COAXIAL) HDMIAUDIO(R)-IN HDMIAUDIO(L)-IN COMPONENTAUDIO(R)-IN COMPONENTAUDIO(L)-IN COMPONENT -Pr-IN COMPONENT -Pb-IN COMPONENT -Y-IN CN3702 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CL3702 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 CL3701 CN3701 1 P-ON-H2 AUDIO(L)-OUT 2 3 GND AUDIO(R)-OUT 4 PROTECT3 5 AMP(L)-OUT 6 7 GND AMP(R)-OUT 8 P-ON-H1 9 10 P-ON+3V 11 PROTECT1 GND 12 LED-R 13 P-ON+5V 14 PROTECT2 15 P-ON+7V 16 GND 17 18 GND 19 P-ON+3.3V 20 P-ON+3.3V 21 AL+3.3V 22 AL+3.3V 23 GND 24 OE2 25 REMOTE BACKLIGHT-SW 26 27 LED1 BACKLIGHT-ADJ 28 VCOM-PWM 29 CN301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 1 CL801 2 1 CL802 2 CN801 SP(L)SP(L)+ CN802 SP(R)SP(R)+ TUNER UNIT SP802 SPEAKER R-CH SP801 SPEAKER L-CH CN101 1 2 3 4 5 6 CL701A 1 2 3 4 5 6 7 8 9 CN631 1 2 3 4 5 6 7 8 9 10 11 CL104 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 CL701 S-VIDEO-Y-IN S-VIDEO-SW S-VIDEO-C-IN GND VIDEO-IN GND AUDIO(L)-IN GND AUDIO(R)-IN CL1001 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ GND GND GND GND GND INV+35V INV+35V INV+35V POWER SUPPLY CBA DIGITAL MAIN CBA UNIT CN1203 1 2 CN1202 1 2 CN1201 1 2 CBA FUNCTION CBA CL104B 6 5 4 3 2 1 CL701B 1 2 3 4 JACK 5 6 7 8 9 INVERTER CBA WH1001 11 10 9 8 7 6 5 4 3 2 1 CN201 1 2 3 4 5 6 7 8 9 10 11 S-VIDEO -IN AUDIO(R) -IN AUDIO(L) -IN VIDEO-IN CL201 GND LCD+13V LCD+13V VGH GND P-ON+3.3V P-ON+3.3V LCD-6V GND VCOM GND LCD MODULE ASSEMBLY BACK LIGHT BACK LIGHT BACK LIGHT CL3902 STV XAO OE1 CPV POL TP GND LLV5(-) LLV5(+) LLV4(-) LLV4(+) LLV3(-) LLV3(+) GND LLVCLK(-) LLVCLK(+) GND LLV2(-) LLN2(+) LLV1(-) LLV1(+) LLV0(-) LLV0(+) GND CN3902 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 HDMICONNECTOR-3 HDMICONNECTOR-2 HDMICONNECTOR-1 WIRING DIAGRAM FL11.3AWI EXPLODED VIEWS Cabinet LC260SS2, 26MF301B/F7 A12 A1 Digital Main CBA Unit L8 B1 L8 L8 CL3701 L6 B51 CL3702 A14 A24 B51 CL3902 LC260EM2, LC260SS2 CL801 B27 L24 B44 CL201 L6 A42 L8 B53 Jack CBA A22 SP801 B9 A21 CL802 L2 B17 B52 L2 B21 B53 A6 B5 L2 A13 L24 Function CBA L8 L2 B5 L1 B40 SP802 B8 LCD1 L8 L3 B52 L8 A16 L1 S5 B11 See Electrical Parts List for parts with this mark. A15 L8 L5 Power Supply CBA L1 L14 A10 AC601 Inverter CBA L1 L1 S5 B4 L8 L1 LC260SS2 Stand Assembly Stand Assembly L9 13-1 L9 FL11.3-A_CEX Packing X3 X4 X6 L9 X2 Some Ref. Numbers are not in sequence. S2 S6 Tape X1 Stand Assembly S4 Fixlon Tape X10 S5 S3 Packing Tape S5 FRO NT FR ON T Packing Tape S1 13-2 FL11.3PEX PARTS LIST [LC260EM2 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don’t degrade the safety of the product through improper servicing. Ref. No. Description Part No. PACKING NOTE: Parts that are not assigned part numbers (---------) are not available. Ref. No. Description S1 CARTON A17A1UH 1EM434239 S2 STYROFOAM TOP A17A1UH 1EM027565 S3 STYROFOAM BOTTOM A17A1UH 1EM027566 S4 SET BAG L3207UH 1EM320295 S5 SERIAL NO. LABEL A01PBUH ---------- S6 STAND BAG A94F0UH 1EM428757 ACCESSORIES Part No. X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A X2# OWNERS MANUAL A17A1UH 1EMN27779 NH001UD X3 REMOTE CONTROL NH001UD STAND ASSEMBLY A01F0UH 1ESA26286 X4 DRY BATTERY R03/2S XB0M451T0006 A1 FRONT CABINET A17A1UH 1EM027545 X6 QUICK START GUIDE A17A1UH 1EMN27780 A6 REAR CABINET A01A1UH 1EM024945A X10 REGISTRATION CARD (EMERSON) A17N1UH 1EMN27763 A10# RATING LABEL A17A1UH ---------- A13 JACK HOLDER(A) A01A1UH 1EM223864 A14 JACK HOLDER(D) A94N0UH 1EM222784 A15 JACK LABEL(A) A01A1UH 1EM431777 A16 JACK LABEL(B) A01A1UH 1EM431778 A21 FUNCTION KNOB A17A1UH 1EM330558 A22 SENSOR LED LENS A17A1UH 1EM330537 A24 ENERGY STAR LABEL A91F2UH ---------- A42 ENERGY GUIDE LABEL A17A1UH ---------- B1 SHIELD BOX A01F2UH 1EM224323 B4 STAND HOLDER 26W A01A1UH 1EM223865A B5 WALL MOUNT BRACKET A84N0UH 1EM323797 B8 SPEAKER HOLDER (L) A94F0UH 1EM123233 B9 SPEAKER HOLDER (R) A94F0UH 1EM123234 B17 PCB HOLDER A01A1UH 1EM328117 B21 SHIELD PLATE A17A1UH 1EM330178 B27 GASKET A8AF0UH 1EM425861 B40 RUBBER CUSHION A72N0JH 1EM425197 B44 THERMAL SHEET TMS-L-3 20X20HC XK10000X4009 B51 CLOTH(10X190XT0.3) L0200UA 1EM420019 B52 CLOTH(10X90XT1.0) A7120UH 1EM424258 B53 CLOTH(15X30XT1.0) B7507UH 0EM402452 CL201 WIRE ASSEMBLY 11PIN FFC 11PIN 90MM WX1A9170-107 CL801 WIRE ASSEMBLY 2PIN 2PIN 155MM RED BLACK WX1A01A0-201 CL802 WIRE ASSEMBLY 2PIN 2PIN 155MM RED BLACK WX1A01A0-201 CL3701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 CL3702 WIRE ASSEMBLY 29PIN FFC 29PIN 70MM WX1A94F0-111 CL3902 WIRE ASSEMBLY 24PIN FFC 24PIN 80MM WX1A94F0-106 L1 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140 L2 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100 L5 SCREW TAP TIGHT M3X10 BIND HEAD+BLK NI GBHS3100 L6 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080 L8 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B L9 STAND SCREW KIT A1DA0UH 1ESA28845 L14 SCREW SEMS M4X8 PAN HEAD + FPJ34080 L24 SHOULDER SCREW A01Q0UF 1EM328277 LCD1 LCD MODULE CMO 6BIT NORMALGRADE UJ26MXB SP801 SPEAKER MAGNETIC SO412F24 DS08120XQ003 SP802 SPEAKER MAGNETIC SO412F24 DS08120XQ003 2011/04/07 14-1 A17A1CA.fm Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don’t degrade the safety of the product through improper servicing. Ref. No. C602# NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. Description CAP METALIZED FILM 0.47µF/300V K 3.5MM Part No. CT2F474DC004 C605 CAP ELECTROLYTIC 270µF/200V CEA271DYG005 C606 CAP ELECTROLYTIC 270µF/200V CEA271DYG005 C609 POLYESTER FILM CAP. (PB FREE) 0.1µF/100V CA2A104DT018 J C610 POLYESTER FILM CAP. (PB FREE) 0.0012µF/ 100V J CA2A122DT018 C611 CERAMIC CAP. 560pF/2KV CA3D561PAN04 C612 POLYESTER FILM CAP. (PB FREE) 0.068µF/ 100V J CA2A683DT018 C613 POLYESTER FILM CAP. (PB FREE) 0.0015µF/ 100V J CA2A152DT018 C631 ELECTROLYTIC CAP. 470µF/25V M CE1EMZNDL471 C632 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V M CE0KMZNDL222 CE1JMASDL470 C.....±0.25% D.....±0.5% F.....±1% C633 G.....±2% J......±5% K.....±10% C634 ELECTROLYTIC CAP. 47µF/50V M C637 CERAMIC CAP. 2200pF/1KV CCD3AKA0R222 C638 ELECTROLYTIC CAP. 2200µF/35V M CE1GMZNDL222 C639 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102 C642 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 CE1AMZNDL332 M.....±20% N.....±30% Z.....+80/-20% DIGITAL MAIN CBA UNIT Ref. No. Description DIGITAL MAIN CBA UNIT Part No. A17A1MMA-001 MPW CBA Ref. No. Description Part No. MPW CBA Consists of the following: A17A1MPW-001 POWER SUPPLY CBA(MPW-1) JACK CBA(MPW-2) ------------------- POWER SUPPLY CBA Ref. No. Description POWER SUPPLY CBA(MPW-1) Consists of the following: Part No. ---------- CAPACITORS C644 ELECTROLYTIC CAP 3300µF/10V C645 ELECTROLYTIC CAP 3300µF/6.3V M CE0KMZNDL332 C646 POLYESTER FILM CAP. (PB FREE) 0.0022µF/ 100V J CA2A222DT018 C648 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101 C652 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C653 ELECTROLYTIC CAP. 220µF/10V M H7 CE1AMAVSL221 C654 ELECTROLYTIC CAP. 220µF/10V M H7 CE1AMAVSL221 C656 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101 C657 ELECTROLYTIC CAP. 22µF/50V M H7 CE1JMAVSL220 C676 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C681 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C682 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C683 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C684 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C691# SAFTY CAP. 3300pF/250V KX CA2E332MR101 C693# SAFTY CAP. 1000pF/250V KX CA2E102MR101 C723 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C201 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C202 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C724 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 C203 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C731 C204 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2 C732 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 C207 CHIP CERAMIC CAP.(1608) B K 0.1µF/16V CHD1CK30B104 C733 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 C210 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C734 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 CHD1JJ3CH102 C735 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C216 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V C217 CHIP CERAMIC CAP.(1608) B K 0.1µF/16V CHD1CK30B104 C736 C218 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C743 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C219 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C744 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C221 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C771 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C222 ELECTROLYTIC CAP. 470µF/16V M CE1CMASDL471 C772 C223 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C775 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C224 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2 C776 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 CHD1JZ30F104 C801 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C302 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V C303 ELECTROLYTIC CAP. 330µF/10V M CE1AMASDL331 C802 C304 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C803 C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C804 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C805 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 CHD1EK30B105 C306 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C309 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C806 CHIP CERAMIC CAP.(1608) B K 1µF/25V C310 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C807 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C311 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C808 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C601# CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004 2011/04/07 14-2 C809 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C810 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 A17A1EL.fm Ref. No. Description Part No. Ref. No. Description Part No. C811 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474 D208 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C815 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 D209 DIODE ZENER 36BSB-T26 NDTB036BST26 C816 ELECTROLYTIC CAP. 10µF/50V M H7 CE1JMASSL100 D210 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 C817 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 D211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C818 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D404 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C819 ELECTROLYTIC CAP. 10µF/50V M H7 CE1JMASSL100 D405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C820 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 D407 DIODE ZENER 10BSB-T26 NDTB010BST26 C821 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D410 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C822 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 D411 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C824 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 D412 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C825 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D413 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C826 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 D414 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C827 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102 D415 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C828 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D417 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26 C829 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D418 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26 C830 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474 D419 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C832 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3 D420 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C833 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D421 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C834 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 D422 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C835 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561 D601# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU C836 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 D602# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU C837 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561 D603# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU C838 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 D604# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU C839 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 D606# DIODE ZENER 27BSB-T26 NDTB027BST26 C841 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 D607 DIODE ZENER 4V3BSB-T26 NDTB4R3BST26 C842 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 D609# SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C843 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D611 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C844 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMAVSL100 D612# DIODE ZENER 39BSB-T26 NDTB039BST26 C847 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 D620 DIODE ZENER 1ZB220-YBB NDWZ01ZB220Y C848 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 D631 DIODE FR154 NDLZ000FR154 C849 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 D632 DIODE FR104-B NDLZ000FR104 C871 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332 D633 DIODE FAST RECOVERY FR151-B/P NDWZ0FR151BP C872 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332 D634 DIODE SHOTTKY SB3200BR NDWZ3200D027 C873 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 D635 DIODE ZENER 1ZB22BB NDWZ0001ZB22 C874 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 D636 DIODE SHOTTKY SB3200BR NDWZ3200D027 C875 CHIP CERAMIC CAP. CH J 180pF/50V CHD1JJ3CH181 D638 DIODE FR154 NDLZ000FR154 C876 CHIP CERAMIC CAP. CH J 180pF/50V CHD1JJ3CH181 D639 DIODE ZENER 1ZB43BB NDWZ0001ZB43 C877 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 D641 SCHOTTKY BARRIER DIODE SB390 NDWZ000SB390 C878 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 D642 SCHOTTKY BARRIER DIODE SB390 NDWZ000SB390 C879 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 D643 DIODE FR104-B NDLZ000FR104 C880 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101 D644 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 C882 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 D645 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038 C883 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 D646 DIODE SCHOTTKY SB360BH NDWZ000SB360 C884 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 D647 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140 C885 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 D650 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D652 DIODE ZENER HZS5.6NB2TE-EQ QDTB0HZS5R6N CONNECTORS CN101 PH CONNECTOR TOP 6P B6B-PH-K-S (LF)(SN) J3PHC06JG029 D657 DIODE ZENER 33BSB-T26 NDTB033BST26 CN201 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 D658 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 D659 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 CN302 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 D660 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 CN631 PH CONNECTOR TOP 11P B11B-PH-KS(LF)(SN) J3PHC11JG029 D661 DIODE FR154 NDLZ000FR154 CN801 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 D662 DIODE FR154 NDLZ000FR154 D665 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 D666 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 D670 DIODE ZENER 10BSB-T26 NDTB010BST26 CN802 DIODES D671 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 D202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D801 DIODE ZENER 20BSB-T26 NDTB020BST26 D203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D802 DIODE ZENER 20BSB-T26 NDTB020BST26 D204 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 D804 DIODE ZENER 20BSB-T26 NDTB020BST26 D205 DIODE ZENER 24BSA-T26 NDTA024BST26 D805 DIODE ZENER 20BSB-T26 NDTB020BST26 D206 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D806 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D207 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 2011/04/07 14-3 A17A1EL.fm Ref. No. Description Part No. Ref. No. R202 ICS Description Part No. RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 IC201 IC TL3472CDR NSZBA0TTY115 R204 RES CARBON FILM T 1/4W J 2.0k Ω RCX4202T1001 IC601# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF R206 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 IC631 IC LD1117V NSZBA0SSS046 R207 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 IC771 IC SWITCHING TC4052BF(ELNF) QSZBA0TTS162 R208 RES CHIP 1608 1/10W J 1 Ω RRJ1R0RYL002 IC801 IC D-AMP BD5426EFS-E2 QSZBA0TRM137 R209 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 IC871 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 R210 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R211 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 LLARKBSTU330 R212 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 COILS L301 INDUCTOR 33µH-K-5FT L302 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 R213 L303 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 R214 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 L601# COIL LINE FILTER ST0807ET28-009 10MH LLEG0Z0Y2029 R216 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 L602# COIL LINE FILTER ST0807ET28-009 10MH LLEG0Z0Y2029 R217 RES CHIP 1608 1/10W J 330 Ω RRJ331RYL002 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 L801 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330 R218 L802 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330 R219 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 L803 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330 R220 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 L804 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330 R223 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 XZ40C0SHG002 R224 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R225 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 L871 WIRE COPPER 6111-06003-0120 TRANSISTORS Q171 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R226 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 Q172 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R227 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 NQS1KTA1267P R228 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 Q201 TRANSISTOR KTA1267-GR-AT/P Q202 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R229 Q203 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R231 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 Q204 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R232 RES CHIP 1608 1/10W F 9.10k Ω RTW9101HH008 NQSYKTC3198P R233 RES CHIP 1608 1/10W F 150 Ω RTW1500HH008 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 RCX4331T1001 Q205 TRANSISTOR KTC3198-Y-AT/P Q207 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R234 Q208 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R235 RES CARBON FILM T 1/4W J 330 Ω Q209 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R236 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001 Q210 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R237 Q211 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R238 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 Q212 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R240 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 Q213 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F R241 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 NQSYKTC3198P R242 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 Q401 TRANSISTOR KTC3198-Y-AT/P Q402 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R243 Q601# MOS FET TK8A50D QFWZTK8A50DQ R245 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001 Q602# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F R247 RES. CARBON FILM J 1/2W J 3.3 Ω RCX23R3T1003 NQSYKTC3198P R248 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 RES CARBON FILM T 1/4W J 6.8 Ω RCX46R8T1001 RCX46R8T1001 Q631 TRANSISTOR KTC3198-Y-AT/P Q632 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F R250 Q634 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R251 RES CARBON FILM T 1/4W J 6.8 Ω Q635 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R252 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R253 RES CARBON FILM T 1/4W J 4.7 Ω RCX44R7T1001 Q636 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F Q637 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R302 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 Q638 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R303 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 Q639 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R304 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 QQSY2SC2120F R308 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 Q640 TRANSISTOR 2SC2120-Y(TE2 F T) Q641 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R309 Q642 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R401 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 Q643 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F R402 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 NQSYKTC3198P R403 RES CHIP 1608 1/10W J 27k Ω RRJ273RYL002 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 Q771 TRANSISTOR KTC3198-Y-AT/P Q772 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R404 Q801 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R405 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 Q802 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R407 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 NQSYKTC3198P R410 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 RES CHIP 1608 1/10W F 36.0k Ω RTW3602HH008 Q841 TRANSISTOR KTC3198-Y-AT/P Q871 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R411 Q872 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R412 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 Q873 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R413 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 NQS1KTA1267P R601# RES. CARBON FILM J 1/2W J 1.2M Ω RCX2125T1003 R602# CEMENT RESISTOR 5W J 2.2 Ω H 10MM RW052R2PAK10 Q874 TRANSISTOR KTA1267-GR-AT/P RESISTORS R172 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R175 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R201 2011/04/07 14-4 R604 CHIP RES.(3216) 1/4W J 0 Ω RRX4JR7Z0000 R605 CHIP RES. 1/4W J 750k Ω RRX4JR7Z0754 R610 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R611 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 A17A1EL.fm Ref. No. Description Ref. No. Part No. Description RCX4152T1001 R614# METAL OXIDE FILM RES. 2W J 0.27 Ω RN02R27ZU001 R735 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 R615 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 R736 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 R616 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 R743 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R617# CEMENT RESISTOR 5W J 2.2 Ω H 10MM RW052R2PAK10 R744 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R632 RES CARBON FILM T 1/4W J 1.0 Ω RCX41R0T1001 R745 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R633 RES. CARBON FILM J 1/2W J 3.3 Ω RCX23R3T1003 R746 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R634 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008 R763 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R635 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008 R771 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 R636 RES. CARBON FILM J 1/2W J 3.3 Ω RCX23R3T1003 R772 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R734 RES CHIP 1608 1/10W J 10 Ω Part No. RES CARBON FILM T 1/4W J 1.5k Ω R613 RRJ100RYL002 R637 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008 R773 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R641 RES CHIP 1608 1/10W D 1.10k Ω RTW1101HH007 R774 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R642 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007 R775 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R643 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007 R776 RES CARBON FILM T 1/4W J 100k Ω RCX4104T1001 R644 RES CHIP 1608 1/10W F 82.0k Ω RTW8202HH008 R777 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R646 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R778 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R647 RES CHIP 1608 1/10W F 75.0k Ω RTW7502HH008 R779 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R649 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 R801 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R650 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R802 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008 R651 RES CHIP 1608 1/10W J 1 Ω RRJ1R0RYL002 R803 RES CHIP 1608 1/10W F 11.0k Ω RTW1102HH008 R652 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R804 RES CHIP 1608 1/10W F 11.0k Ω RTW1102HH008 R653 RES CHIP 1608 1/10W F 36.0k Ω RTW3602HH008 R806 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R654 RES CHIP 1608 1/10W J 5.6k Ω RRJ562RYL002 R807 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R655 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R810 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R656 RES CARBON FILM T 1/4W J 8.2 Ω RCX48R2T1001 R813 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R657 RES CARBON FILM T 1/4W J 8.2 Ω RCX48R2T1001 R814 RES CHIP 1608 1/10W J 6.8k Ω RRJ682RYL002 R658 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R815 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R659 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 R816 RES CHIP 1608 1/10W J 6.8k Ω RRJ682RYL002 R660 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R817 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R661 RES. CARBON FILM J 1/2W J 220 Ω RCX2221T1003 R818 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R662 RES CARBON FILM T 1/4W J 15 Ω RCX4150T1001 R819 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R663 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R820 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R664 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R842 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R665 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R843 RES CHIP 1608 1/10W J 110 Ω RRJ111RYL002 R666 RES CARBON FILM T 1/4W J 1.0 Ω RCX41R0T1001 R844 RES CHIP 1608 1/10W J 220 Ω RRJ221RYL002 R668 RES CHIP 1608 1/10W F 620 Ω RTW6200HH008 R846 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R669 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R847 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R672 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 R848 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R673 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R871 RES CHIP 1608 1/10W J 560 Ω RRJ561RYL002 R674 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R872 RES CHIP 1608 1/10W J 560 Ω RRJ561RYL002 R675 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R873 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R676 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 R874 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R677 RES CARBON FILM T 1/4W J 330 Ω RCX4331T1001 R875 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R678 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R876 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R679 RES CHIP 1608 1/10W F 3.60k Ω RTW3601HH008 R877 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R680 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 R878 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R682 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R879 RES CHIP 1608 1/10W J 18k Ω RRJ183RYL002 R683 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R880 RES CHIP 1608 1/10W J 18k Ω RRJ183RYL002 R684 RES CARBON FILM T 1/4W J 1.8 Ω RCX41R8T1001 R881 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 R685 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001 R882 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 R686 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R883 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R687 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001 R884 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R688 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R885 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R689 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R886 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R691 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R887 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R693 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R888 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R696 METAL RESISTOR 1W J 3.9 Ω RN013R9ZU001 R891 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R697 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R892 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R698 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R893 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R723 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R724 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 AC601# AC CORD UL 1855MM BLACK WAC0182LW007 R725 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 B11 POW HEAT SINK A7120UH 1EM423993 R726 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 2011/04/07 MISCELLANEOUS 14-5 A17A1EL.fm Ref. No. Description Part No. BC301 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC801 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC802 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC803 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC804 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC805 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC807 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 BC841 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 CL701 WIRE ASSEMBLY 9P 9PIN/170MM WX1A94F0-002 F601# FUSE STC4A125V U/CT PAGE20CW3402 FH601 FUSE HOLDER MSF-015 LF (B110) FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 JK721 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 JK722 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 JK731 JACK RCA PCB S GREEN 01/RCA-101H(GN) JXRJ010YUQ03 JACK RCA PCB S BLUE 01/RCA-101H(BL) JACK RCA PCB S RED 01/RCA-101H(RD) JK741 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 JK742 JACK SW RCA PCB S RED RCA-102H(RD) JYRJ010YUQ03 JK841 JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 JK872 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 JS202 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 SA601# SCREW B-TIGHT D3X8 BIND HEAD+ SURGE ABSORBER 470V+-10PER TRANS POWER BCK-28-9904 LTT2PC0XB062 EYELET TYPE D-1 0VM406868 TU301 EYELET TYPE D-1 0VM406868 TUNER UNIT ATSC/NTSC/QAM TDYU4-D02A UTNATS0AL001 JACK CBA Ref. No. Description JACK CBA(MPW-2) Consists of the following: INVERTER CBA FUNCTION CBA A17A1M1V-001-IV A17A1M1V-001-FN Description Part No. ---------- CAPACITORS NVQZ10D471KB TM601 Part No. A17A1M1V-001 INVERTER CBA Consists of the following: GBJB3080 T601# TM602 Ref. No. JXRJ010YUQ01 JK871 Description INVERTER ASSEMBLY Consists of the following: INVERTER CBA JXRJ010YUQ04 JK733 L3 Ref. No. XH01Z00LY002 FH602 JK732 INVERTER ASSEMBLY Part No. ---------- CAPACITORS C1001 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C1002 ELECTROLYTIC CAP. 100µF/35V M CE1GMASDL101 C1003 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1004 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101 CHD1JK30B104 C1005 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V C1006 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224 C1007 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1008 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 C1010 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1011 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224 C1012 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1016 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1018 CHIP CERAMIC CAP. B K 0.01µF/25V CHD1EK30B103 C1019 CHIP CERAMIC CAP. B K 0.01µF/25V CHD1EK30B103 C1020 CHIP CERAMIC CAP. B K 0.01µF/25V CHD1EK30B103 C1021 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C1023 ELECTROLYTIC CAP. 470µF/35V M CE1GMZNDL471 C1024 ELECTROLYTIC CAP. 470µF/35V M CE1GMZNDL471 C1103 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473 C1104 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 C1106 CHIP CERAMIC CAP.(1608) CH J 1800pF/50V CHD1JJ3CH182 CHD1JK30B104 C1107 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V C1108 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 C1109 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473 C1110 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C1111 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 C754 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C1112 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 C755 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C1113 CAP METALIZED FILM 1.0µF/63V J CT1K105SER01 C756 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C1114 CAP METALIZED FILM 1.0µF/63V J CT1K105SER01 C757 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C1115 CAP METALIZED FILM 1.0µF/63V J CT1K105SER01 C758 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C1116 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7 R751 RES CHIP 1608 1/10W J 75 Ω RESISTORS C1123 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473 RRJ750RYL002 C1201 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007 R752 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 C1203 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007 R753 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 C1205 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007 R756 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C1206 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 R757 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C1207 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007 R758 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 C1208 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 R759 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 C1209 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007 R760 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 C1210 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 R761 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 C1211 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007 R762 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 C1212 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 C1213 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 MISCELLANEOUS JK751 JACK SW DIN PCB L DIN-435C(777D) JYEL040YUQ03 C1214 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 JK752 JACK RCA PCB L RCA-101S(1)-03 JXRL010YUQ12 C1215 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 JK753 JACK RCA PCB L RCA-101S(1)-04 JXRL010YUQ13 JK754 JACK SW RCA PCB L RCA-102F(RD) JYRL010YUQ05 CONNECTORS CN1201# CONNECTOR/JACK 1747386-1 JB17J02AP002 CN1202# CONNECTOR/JACK 1747386-1 JB17J02AP002 CN1203# CONNECTOR/JACK 1747386-1 JB17J02AP002 DIODES D1001 2011/04/07 14-6 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26 A17A1EL.fm Ref. No. Description Part No. Ref. No. Description Part No. D1002 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1015 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 D1003 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1016 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 D1004 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1017 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 D1005 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1018 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 D1006 DIODE ZENER 27BSB-T26 NDTB027BST26 R1019 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 D1101 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 R1020 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008 D1102 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1021 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 D1103 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 R1022 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 D1104 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1023 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 D1201 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1024 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 D1202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1025 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 D1203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1026 RES CARBON FILM T 1/4W J 5.6k Ω RCX4562T1001 D1204 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1027 RES CARBON FILM T 1/4W J 5.6k Ω RCX4562T1001 D1205 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1028 RES CARBON FILM T 1/4W J 5.6k Ω RCX4562T1001 D1206 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1029 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 D1207 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1030 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 D1208 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1031 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 D1209 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1032 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 D1210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1033 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 D1211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1034 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 D1212 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1035 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 D1213 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1036 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 D1214 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1037 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 D1215 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1101 RES CARBON FILM T 1/4W J 5.1k Ω RCX4512T1001 D1216 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1102 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 D1217 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1103 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 D1218 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1116 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 D1219 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1117 RES CHIP 1608 1/10W F 110k Ω RTW1103HH008 D1220 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1118 RES CHIP 1608 1/10W J 33k Ω RRJ333RYL002 D1221 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1119 RES CHIP 1608 1/10W J 30k Ω RRJ303RYL002 D1222 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1120 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 D1223 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1121 RES CHIP 1608 1/10W J 5.1k Ω RRJ512RYL002 D1224 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1122 RES CARBON FILM T 1/4W J 5.1k Ω RCX4512T1001 D1225 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1123 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 D1226 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1124 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 D1227 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1137 RES CHIP 1608 1/10W J 56k Ω RRJ563RYL002 R1138 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 ICS IC1001 IC BA10324AF-E2 QSZBA0TRM032 R1201 RES CHIP 1608 1/10W F 390 Ω RTW3900HH008 IC1101 IC INVERTER CONTROLLER OZ9933GN-A-0TR NSCA0TTMC001 R1202 RES CHIP 1608 1/10W F 390 Ω RTW3900HH008 R1203 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 R1204 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 TRANSISTORS Q1004 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R1205 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008 Q1005 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R1206 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008 Q1006 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R1207 RES CHIP 1608 1/10W F 390 Ω RTW3900HH008 Q1007 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R1208 RES CHIP 1608 1/10W F 390 Ω RTW3900HH008 Q1008 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R1209 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 Q1009 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R1210 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 Q1101 FET MOS FDD5614P/Z NF2ZFDD5614P R1211 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008 Q1102 FET MOS FDD5612/Z NF2ZFDD56120 R1212 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008 Q1112 FET MOS FDD5614P/Z NF2ZFDD5614P R1213 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 Q1113 FET MOS FDD5612/Z NF2ZFDD56120 R1214 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1215 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 RESISTORS R1004 METAL OXIDE RES. 2W J 2.7k Ω RN02272ZU001 R1216 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 R1005 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R1217 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 R1006 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1218 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1007 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1219 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1008 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1220 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 R1009 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R1221 RES CHIP 1608 1/10W F 390 Ω RTW3900HH008 R1010 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1222 RES CHIP 1608 1/10W F 390 Ω RTW3900HH008 R1011 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R1223 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 R1012 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R1224 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1013 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R1225 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1014 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1226 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 2011/04/07 14-7 A17A1EL.fm Ref. No. R1227 Description RES CHIP 1608 1/10W F 47.0k Ω Part No. RTW4702HH008 R1228 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008 R1229 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008 R1230 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008 MISCELLANEOUS BC1201 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC1203 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 CL1001 WIRE ASSEMBLY 11PIN 11PIN/100MM/AWG26 WX1A04A0-003 JS1005 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 T1201# TRANS INVERTER HVT-266 LTZ3PZ0XB015 T1202# TRANS INVERTER HVT-266 LTZ3PZ0XB015 T1203# TRANS INVERTER HVT-266 LTZ3PZ0XB015 FUNCTION CBA Ref. No. Description FUNCTION CBA Consists of the following: Part No. ---------- CAPACITORS C108 CAP CERAMIC (AX) 0.1µF/50V/B/K C113 ELECTROLYTIC CAP. 47µF/16V M H7 CA1J104TU061 CE1CMAVSL470 C115 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331 D104 LED GREEN 333GT/E(FNA) NPWZ33GTEFNA D105 LED L-53HT NP4Z000L53HT D107 CAP CERAMIC (AX) 0.1µF/50V/B/K DIODES CA1J104TU061 RESISTORS R108 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R109 RES CARBON FILM T 1/4W G 10k Ω RCX4103T1002 R111 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 R113 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002 R114 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 R115 RES CARBON FILM T 1/4W G 8.2k Ω RCX4822T1002 R116 RES CARBON FILM T 1/4W G 18k Ω RCX4183T1002 R123 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R124 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R126 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R127 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 R128 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001 SWITCHES SW101 TACT SWITCH SKHHLMA010 SST0101AL049 SW103 TACT SWITCH SKHHLMA010 SST0101AL049 SW104 TACT SWITCH SKHHLMA010 SST0101AL049 SW105 TACT SWITCH SKHHLMA010 SST0101AL049 SW106 TACT SWITCH SKHHLMA010 SST0101AL049 SW107 TACT SWITCH SKHHLMA010 SST0101AL049 MISCELLANEOUS CL104 WIRE ASSEMBLY 6PIN 6PIN 170MM RS102 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 2011/04/07 WX1A01A0-011 14-8 A17A1EL.fm 26MF301B/F7(A17A4UH)(Serial No.: DS2) 20110322 26MF301B/F7(A17A4UH)(Serial No.: DS2) Different parts from the original model LC260EM2(DS1) Ref. No. Description MECHANICAL PARTS A1 FRONT CABINET A17A0UH A10! RATING LABEL A17A0UH A12 POP LABEL A17A2UH A42 Not used B44 THERMOSTAR TS-500(12X12X3) LCD MODULE CMO 6BIT NORMALGRADE LCD1 S1 CARTON A17A0UH X2! OWNERS MANUAL A17A0UH X3 REMOTE CONTROL NF805UD X6 QUICK START GUIDE A17A0UH X10 REGISTRATION CARD (MAGNAVOX) A17N0UH Parts No. 1EM028145 ------------------XK1000TYG001 UJ26MXA 1EM435327 1EMN28259 NF805UD 1EMN28260 1EMN27759 ELECTRICAL PARTS C835 C837 C875 C876 R814 R816 R879 R880 DIGITAL MAIN CBA UNIT A17A4MMA-001 MPW CBA POWER SUPPLY CBA CHIP CERAMIC CAP.(1608) B K 2700PF/50V CHIP CERAMIC CAP.(1608) B K 2700PF/50V CHIP CERAMIC CAP.(1608) CH J 270PF/50V CHIP CERAMIC CAP.(1608) CH J 270PF/50V RES CHIP 1608 1/10W J 3.3K OHM RES CHIP 1608 1/10W J 3.3K OHM RES CHIP 1608 1/10W J 47K OHM RES CHIP 1608 1/10W J 47K OHM A17A2MPW-001 ---------CHD1JK30B272 CHD1JK30B272 CHD1JJ3CH271 CHD1JJ3CH271 RRJ332RYL002 RRJ332RYL002 RRJ473RYL002 RRJ473RYL002 1 / 1 page REVISION HISTORY Chassis FL11.3 • 2011-03-15 LC260EM2 (Serial No. : DS1) added • TBD LC260SS2 (Serial No.: DS1) added • TBD 26MF301B/F7 (Serial No.: DS1) added • TBD 26MF301B/F7 (Serial No.: DS2) added 15-1 FL11.3REV COMPARISON LIST OF MODEL NAME Chassis FL11.3 LC260EM2 (DS1) A17A1UH LC260SS2 (DS1) A17A2UH 26MF301B/F7 (DS1) A17A0UH (DS2) A17A4UH FL11.3COM