Download IPSO IHC035 User's Manual

On-Premise
Laundry
Planning
Handbook
CHM2097N
IHC Washer-Extractors
Refer to Installation manual for full instructions.
5-08-52R1
June 2011
Table of
Contents
Washer-Extractors ...................................................................
Introduction............................................................................
Model Identification - IHC Washer-Extractors..................
Specifications and Dimensions - Model IHC012 ...................
Specifications and Dimensions - Model IHC018 ...................
Specifications and Dimensions - Model IHC025 ...................
Specifications and Dimensions - Model IHC030 ...................
Specifications and Dimensions - Model IHC035 ...................
Installation - IHC Models .......................................................
2
2
2
3
7
11
15
19
23
© Published by permission of the copyright owner.
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-51
Washer-Extractors
Introduction
Model Identification - IHC Washer-Extractors
CHM2097N
Figure 1
5-08-52
IHC012
IHC025
IHC018
IHC030
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
IHC035
2
Washer-Extractors
Specifications and Dimensions - Model IHC012
Capacity (dry weight) Ratio (kg/l)
1:11
11.02 lb. (5 kg)
1:10
12.13 lb. (5.5 kg)
1:9
13.45 lb. (6.1 kg)
Cylinder
Cylinder diameter, in. (mm)
20.87 (530)
Cylinder depth, in. (mm)
9.84 (250)
Cylinder volume, ft.3 (l)
1.94 (55)
Cabinet
Overall height, in. (mm)
40.87 (1038)
Overall width, in. (mm)
25.98 (660)
Overall depth, in. (mm)
22.64 (575)
Front Loading
Door opening size, in. (mm)
11.81 (300)
Height of door bottom above floor, in (mm)
10.98 (279)
Height of door center above floor, in (mm)
19.88 (505)
Speed
10-50 tr/min - RPM
Wash
85 tr/min - RPM
Distribution
250-1250 tr/min - RPM
Spin
G-factor
462
High Spin
Motor (3 phase), 4p, 1470 tr/min
0.74 HP/0.55 kW
2 (51)
Drain Valve, in. (mm)
Water Supply (hard, soft, warm water), in. (mm)
.75 (19)
Direct Steam Heating
Steam inlet connection size, in. (mm)
Not Applicable
Electrical
Electrical Heating (230/400 V)
4.2 kW
6 kW
Electrical Heating (400V)
Steam
Not Applicable
Warm Water (without additional heating)
Not Applicable
Warm Water (with additional heating)
Not Applicable
Packing Dimensions (height X width X depth), in. (mm)
44.88 X 29.13 X 33.07
(1140 X 740 X 840)
Weight
3
Net weight, lb. (kg)
405.65 (184)
Gross weight, lb. (kg)
436.52 (198)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
Machine Dimensions - Model IHC012
39.8 in. (1011 mm)
10.98 in.
(279 mm)
40.87 in. (1038 mm)
6.4 in.
(163 mm)
1.3 in.
(33 mm)
1.3 in.
(33 mm)
2.56 in.
(65 mm)
25.98 in. (660 mm)
1
5.94 in.
(151 mm)
2.95 in.
(75 mm)
1.18 in.
(30 mm)
1.18 in.
(30 mm)
19.09 in. (485 mm)
2.56 in.
(65 mm)
20.87 in. (530 mm)
8.9 in.
(226 mm)
CHM2200N
CHM2100N
2
22.24 in. (565 mm)
2.72 in.
(69 mm)
3
24.49 in. (622 mm)
CHM2201N
CHM220
4
5
4.3 in.
(109 mm)
27.41 in.
(696.2 mm)
7
2.76 in.
(70 mm)
29.41 in. (747 mm)
34.92 in. (887 mm)
10
31.14 in. (791 mm)
6
9
8
7.09 in.
(180 mm)
1.73 in.
(44 mm)
25.98 in. (660 mm)
CHM2202N
1
2
3
4
5
Ventilation Soap Dispenser
Warm Water Connections .75 in.
Liquid Soap Connections
Soft Water Connections .75 in.
Main Switch
6
7
8
9
10
Electrical Connections
Ventilation Tub
Drain Valve
Bolt Pattern for Fixation of the Machine
Hard Water Connections .75 in.
Figure 2
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
4
Washer-Extractors
Mounting Bolt Hole Locations - Model IHC012
1.18 in.
(30 mm)
21.46 in. (545 mm)
19.09 in. (485 mm)
ø0.71 in.
(ø18 mm)
1.18 in.
(30 mm)
2.56 in.
(65 mm)
20.87 in. (530 mm)
2.56 in.
(65 mm)
25.98 in. (660 mm)
CHM2203N
CHM2203N
Figure 3
5
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
WARNING
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
Electrical Installation Requirements - Model IHC012
Boiler Fed/Steam Heat
3
3+PE
3
10
10
14/2.5
P
380-415
50/60
3
3+N+PE
7
15
16
14/2.5
Q
200-240
50/60
3
3+PE
7
15
16
14/2.5
X
200-240
50/60
1/3
2/3+PE
7
15
16
14/2.5
3x2 kW
AWG/mm2
50/60
Recommended
Circuit Breaker
(US-market)
440-480
Full Load
Amps
N
kW Standard
Heating Elements
NON-US
AWG/mm2
Recommended
Circuit Breaker
(US-market)
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
US
Electric Heat
US
NON-US
N/A
N/A
N/A
N/A
16
20
20
12/4.0
23
30
32
10/6.0
N/A
N/A
N/A
N/A
Alternative Electric Heat Options
N
440-480
50/60
3
3+PE
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
2/3+PE
3x1.4 kW
N/A
N/A
N/A
N/A
13
15
16
14/2.5
18
20
20
12/4.0
N/A
N/A
N/A
N/A
Table 1
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
6
Washer-Extractors
Specifications and Dimensions - Model IHC018
Capacity (dry weight) Ratio (kg/l)
1:11
15.21 lb. (6.9 kg)
1:10
16.76 lb. (7.6 kg)
1:9
18.52 lb. (8.4 kg)
Cylinder
Cylinder diameter, in. (mm)
20.87 (530)
Cylinder depth, in. (mm)
13.58 (345)
Cylinder volume, ft.3 (l)
2.68 (76)
Cabinet
Overall height, in. (mm)
40.87 (1038)
Overall width, in. (mm)
25.98 (660)
Overall depth, in. (mm)
29.09 (739)
Front Loading
Door opening size, in. (mm)
11.81 (300)
Height of door bottom above floor, in (mm)
10.98 (279)
Height of door center above floor, in (mm)
19.88 (505)
Speed
10-50 tr/min - RPM
Wash
85 tr/min - RPM
Distribution
250-1000 tr/min - RPM
Spin
G-factor
296
High Spin
Motor (3 phase), 4p, 1470 tr/min
1.01 HP/0.75 kW
2 (51)
Drain Valve, in. (mm)
Water Supply (hard, soft, warm water), in. (mm)
.75 (19)
Direct Steam Heating
Steam inlet connection size, in. (mm)
.38 (10)
Electrical
Electrical Heating (230/400 V)
4.2 kW - 6 kW - 9 kW
12 kW
Electrical Heating (400V)
Steam
Not Applicable
Warm Water (without additional heating)
Not Applicable
Warm Water (with additional heating)
Not Applicable
Packing Dimensions (height X width X depth), in. (mm)
44.88 X 29.13 X 33.07
(1140 X 740 X 840)
Weight
7
Net weight, lb. (kg)
465.18 (211)
Gross weight, lb. (kg)
513.68 (233)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
Machine Dimensions - Model IHC018
10.98 in.
(279 mm)
39.8 in.
(1011 mm)
40.87 in.
(1038 mm)
8.66 in.
(220 mm)
1.3 in.
(33 mm)
2.56 in.
(65 mm)
20.87 in.
(530 mm)
1.3 in.
(33 mm)
2.56 in.
(65 mm)
25.98 in.
(660 mm)
1
23.23 in.
(590 mm)
CHM2204N
5.94 in.
(151 mm)
2.95 in.
(75 mm)
CHM2204N
8.9
in.
(226 mm)
2.72 in.
(69 mm)
28.62 in.
(727 mm)
26.38 in.
(670 mm)
CHM2205N
2
3
4
CHM2
5
10
6
2.76 in.
(70 mm)
27.41 in. (696.2 mm)
29.41 in. (747 mm)
4.3 in.
(109 mm)
19.1 in. (485 mm)
34.92 in. (887 mm)
31.14 in. (791 mm)
9
8
7.09 in.
(180 mm)
25.98 in. (660 mm)
1
2
3
4
5
1.18 in.
(30 mm)
1.18 in.
(30 mm)
Ventilation Soap Dispenser
Warm Water Connections .75 in.
Liquid Soap Connections
Soft Water Connections .75 in.
Main Switch
6
7
8
9
10
7
1.73 in.
(44 mm)
CHM2206N
Electrical Connections
Ventilation Tub
Drain Valve
Steam Connections
Hard Water Connections .75 in
Figure 4
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
8
Washer-Extractors
Mounting Bolt Hole Locations - Model IHC018
1.18 in.
(30 mm)
25.59 in. (650 mm)
23.23 in. (590 mm)
ø0.71 in.
(ø18 mm)
1.18 in.
(30 mm)
2.56 in.
(65 mm)
20.87 in. (530 mm)
2.56 in.
(65 mm)
25.98 in. (660 mm)
CHM2207N
CHM2207N
Figure 5
9
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
WARNING
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
Electrical Installation Requirements - Model IHC018
Boiler Fed/Steam Heat
3
3+PE
4
10
10
14/2.5
P
380-415
50/60
3
3+N+PE
12
15
16
14/2.5
Q
200-240
50/60
3
3+PE
12
15
16
14/2.5
X
200-240
50/60
1/3
2/3+PE
12
15
16
14/2.5
3x2 kW
AWG/mm2
50/60
Recommended
Circuit Breaker
(US-market)
440-480
Full Load
Amps
N
kW Standard
Heating Elements
NON-US
AWG/mm2
Recommended
Circuit Breaker
(US-market)
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
US
Electric Heat
US
NON-US
N/A
N/A
N/A
N/A
21
30
25
10/6.0
27
30
32
10/6.0
N/A
N/A
N/A
N/A
Alternative Electric Heat Options
N/A
N/A
N/A
N/A
18
20
20
12/4.0
23
30
25
10/6.0
2/3+PE
N/A
N/A
N/A
N/A
3
3+PE
N/A
N/A
N/A
N/A
50/60
3
3+N+PE
25
30
32
10/6.0
200-240
50/60
3
3+PE
35
40
40
8/10.0
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
21
30
25
10/6.0
P
380-415
50/60
3
3+N+PE
29
40
32
8/10.0
Q
200-240
50/60
3
3+PE
N/A
N/A
N/A
N/A
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
N
440-480
50/60
P
380-415
Q
3x1.4 kW
3x3 kW
3x4 kW
Table 2
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
10
Washer-Extractors
Specifications and Dimensions - Model IHC025
Capacity (dry weight) Ratio (kg/l)
1:11
18.96 lb. (8.6 kg)
1:10
20.94 lb. (9.5 kg)
1:9
23.15 lb. (10.5 kg)
Cylinder
Cylinder diameter, in. (mm)
20.87 (530)
Cylinder depth, in. (mm)
17.32 (440)
Cylinder volume, ft.3 (l)
3.35 (95)
Cabinet
Overall height, in. (mm)
40.87 (1038)
Overall width, in. (mm)
25.98 (660)
Overall depth, in. (mm)
33.03 (839)
Front Loading
Door opening size, in. (mm)
11.81 (300)
Height of door bottom above floor, in (mm)
10.98 (279)
Height of door center above floor, in (mm)
19.88 (505)
Speed
10-50 tr/min - RPM
Wash
85 tr/min - RPM
Distribution
250-1000 tr/min - RPM
Spin
G-factor
296
High Spin
Motor (3 phase), 4p, 1470 tr/min
1.01 HP/0.75 kW
2 (51)
Drain Valve, in. (mm)
Water Supply (hard, soft, warm water), in. (mm)
.75 (19)
Direct Steam Heating
Steam inlet connection size, in. (mm)
.38 (10)
Electrical
Electrical Heating (230/400 V)
4.2 kW - 6kW - 9 kW
12 kW
Electrical Heating (400V)
Steam
Not Applicable
Warm Water (without additional heating)
Not Applicable
Warm Water (with additional heating)
Not Applicable
Packing Dimensions (height X width X depth), in. (mm)
49.21 X 29.13 X 37.40
(1250 X 740 X 950)
Weight
Net weight, lb. (kg)
520.29 (236)
Gross weight, lb. (kg)
568.79 (258)
11
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
Machine Dimensions - Model IHC025
10.98 in.
(279 mm)
40.87 in.
(1038 mm)
39.8 in.
(1011 mm)
8.66 in.
(220 mm)
1.3 in.
(33 mm)
20.87 in.
(530 mm)
2.56 in.
(65 mm)
25.98 in.
(660 mm)
5.94 in.
(151 mm)
2.56 in.
(65 mm)
8.9 in.
(226 mm)
27.16 in.
(690 mm)
CHM2204N
2.72 in.
(69 mm)
2
3
1.18 in.
(30 mm)
1.18 in.
(30 mm)
CHM2204N
2.95 in.
(75 mm)
1
1.3 in.
(33 mm)
32.56 in.
(827 mm)
30.31 in.
(770 mm)
4
CHM2209N
CHM
5
10
6
7
27.41 in.
(696.2 mm)
29.41 in.
(747 mm)
8
1
2
3
4
5
4.3 in.
(109 mm)
2.76 in.
(70 mm)
19.1 in.
(485 mm)
31.14 in.
(791 mm)
34.92 in.
(887 mm)
9
7.09 in.
(180 mm)
1.73 in.
(44 mm)
25.98 in. (660 mm)
Ventilation Soap Dispenser
Warm Water Connections .75 in.
Liquid Soap Connections
Soft Water Connections .75 in.
Main Switch
CHM2206N
6
7
8
9
10
Electrical Connections
Ventilation Tub
Drain Valve
Steam Connections
Hard Water Connections .75 in
Figure 6
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
12
Washer-Extractors
Mounting Bolt Hole Locations - Model IHC025
1.18 in.
(30 mm)
29.53 in.
(750 mm)
27.17 in.
(690 mm)
ø0.71 in.
(ø18 mm)
1.18 in.
(30 mm)
2.56 in.
(65 mm)
20.87 in.
(530 mm)
2.56 in.
(65 mm)
25.98 in.
(660 mm)
CHM2211N
CHM2211N
Figure 7
13
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
WARNING
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
Electrical Installation Requirements - Model IHC025
Boiler Fed/Steam Heat
3
3+PE
4
10
10
14/2.5
P
380-415
50/60
3
3+N+PE
12
15
16
14/2.5
Q
200-240
50/60
3
3+PE
12
15
16
14/2.5
X
200-240
50/60
1/3
2/3+PE
12
15
16
14/2.5
3x2 kW
AWG/mm2
50/60
Recommended
Circuit Breaker
(US-market)
440-480
Full Load
Amps
N
kW Standard
Heating Elements
NON-US
AWG/mm2
Recommended
Circuit Breaker
(US-market)
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
US
Electric Heat
US
NON-US
N/A
N/A
N/A
N/A
21
30
25
10/6.0
27
30
32
10/6.0
N/A
N/A
N/A
N/A
Alternative Electric Heat Options
N/A
N/A
N/A
N/A
18
20
20
12/4.0
23
30
25
10/6.0
2/3+PE
N/A
N/A
N/A
N/A
3
3+PE
N/A
N/A
N/A
N/A
50/60
3
3+N+PE
25
30
32
10/6.0
200-240
50/60
3
3+PE
35
40
40
8/10.0
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
21
30
25
10/6.0
P
380-415
50/60
3
3+N+PE
29
40
32
8/10.0
Q
200-240
50/60
3
3+PE
N/A
N/A
N/A
N/A
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
N
440-480
50/60
P
380-415
Q
3x1.4 kW
3x3 kW
3x4 kW
Table 3
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
14
Washer-Extractors
Specifications and Dimensions - Model IHC030
Capacity (dry weight) Ratio (kg/l)
1:11
26.46 lb. (12 kg)
1:10
29.10 lb. (13.2 kg)
1:9
31.97 lb. (14.5 kg)
Cylinder
Cylinder diameter, in. (mm)
25.59 (650)
Cylinder depth, in. (mm)
15.75 (400)
Cylinder volume, ft.3 (l)
4.66 (132)
Cabinet
Overall height, in. (mm)
47.32 (1202)
Overall width, in. (mm)
30.71 (780)
Overall depth, in. (mm)
33.15 (842)
Front Loading
Door opening size, in. (mm)
11.81 (300)
Height of door bottom above floor, in (mm)
14.78 (376)
Height of door center above floor, in (mm)
23.82 (605)
Speed
10-50 tr/min - RPM
Wash
85 tr/min - RPM
Distribution
250-1000 tr/min - RPM
Spin
G-factor
363
High Spin
Motor (3 phase), 4p, 1470 tr/min
2.01 HP/1.5 kW
2 (51)
Drain Valve, in. (mm)
Water Supply (hard, soft, warm water), in. (mm)
.75 (19)
Direct Steam Heating
Steam inlet connection size, in. (mm)
.38 (10)
Electrical
Electrical Heating (230/400 V)
12 kW - 15 kW - 18 kW
Electrical Heating (400V)
21 kW - 24 kW
Steam
Not Applicable
Warm Water (without additional heating)
Not Applicable
Warm Water (with additional heating)
Not Applicable
Packing Dimensions (height X width X depth), in. (mm)
51.57 X 33.46 X 37.01
(1310 X 850 X 940)
Weight
Net weight, lb. (kg)
716.50 (325)
Gross weight, lb. (kg)
782.64 (355)
15
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
Machine Dimensions - Model IHC030
8.66 in.
(220 mm)
46.3 in. (1176 mm)
14.78 in.
(376 mm)
47.32 in. (1202 mm)
3.47 in.
(88 mm)
1.34 in.
(34 mm)
2.6 in.
(66 mm)
1.34 in.
(34 mm)
25.51 in. (648 mm)
10.49 in.
(267 mm)
7.93 in.
(202 mm)
4.13 in.
(105 mm)
1
1.44 in.
(36.5 mm)
26.18 in.
(665 mm)
3.23 in.
CHM2212N (82 mm)
32.13 in.
(816 mm)
2.6 in.
(66 mm)
30.71 in. (780 mm)
CHM2212N
13.05 in.
(332 mm)
1.44 in.
(36.5 mm)
CHM2213N
CHM2213N
2
3
4
5
10
8
2.76 in.
(70 mm)
25.98 in.
(660 mm)
2.36 in.
(60 mm)
7.87 in.
(200 mm)
Ventilation Soap Dispenser
Warm Water Connections .75 in.
Hard Water Connections .75 in
Soft Water Connections .75 in.
Main Switch
7
33.17 in.
(843 mm)
4.3 in.
(109.2 mm)
35.16 in.
(893 mm)
20.87 in.
(530 mm)
36.81 in.
(935 mm)
38.11 in.
(968 mm)
1.38 in.
(35 mm)
6
9
1
2
3
4
5
29.92 in.
(760 mm)
CHM2214N
CHM2214N
6
7
8
9
10
Electrical Connections
Ventilation Tub
Drain Valve
Steam Connections
Liquid Soap Connections
Figure 8
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
16
Washer-Extractors
Mounting Bolt Hole Locations - Model IHC030
1.44 in.
(36.5 mm)
29.06 in.
(738 mm)
26.18 in.
(665 mm)
ø0.71 in.
(ø18 mm)
1.44 in.
(36.5 mm)
2.58 in.
(66 mm)
25.51 in.
(648 mm)
2.62 in.
(66 mm)
30.71 in.
(780 mm)
CHM2215N
CHM2215N
Figure 9
17
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
WARNING
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
Electrical Installation Requirements - Model IHC030
Boiler Fed/Steam Heat
3
3+PE
6
15
10
14/2.5
P
380-415
50/60
3
3+N+PE
18
20
20
12/4.0
Q
200-240
50/60
3
3+PE
18
20
20
12/4.0
X
200-240
50/60
1/3
2/3+PE
18
20
20
12/4.0
6x2 kW
AWG/mm2
50/60
Recommended
Circuit Breaker
(US-market)
440-480
Full Load
Amps
N
kW Standard
Heating Elements
NON-US
AWG/mm2
Recommended
Circuit Breaker
(US-market)
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
US
Electric Heat
US
NON-US
23
30
32
10/6.0
36
40
40
8/10.0
49
60
60
6/16.0
N/A
N/A
N/A
N/A
Alternative Electric Heat Options
28
40
40
8/10.0
40
50
50
8/10.0
56
60
60
6/16.0
2/3+PE
56
60
60
6/16.0
3
3+PE
32
40
40
8/10.0
50/60
3
3+N+PE
44
50
50
8/10.0
200-240
50/60
3
3+PE
63
70
70
4/25.00
X
200-240
50/60
1/3
2/3+PE
63
70
70
4/25.00
N
440-480
50/60
3
3+PE
36
40
40
8/10.0
P
380-415
50/60
3
3+N+PE
49
60
60
6/16.0
Q
200-240
50/60
3
3+PE
N/A
N/A
N/A
N/A
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
41
50
50
8/10.0
P
380-415
50/60
3
3+N+PE
53
60
60
6/16.0
Q
200-240
50/60
3
3+PE
N/A
N/A
N/A
N/A
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
N
440-480
50/60
P
380-415
Q
3x3 kW
+
3x2 kW
6x3 kW
3x3 kW
+
3x4 kW
6x4 kW
Table 4
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
18
Washer-Extractors
Specifications and Dimensions - Model IHC035
Capacity (dry weight) Ratio (kg/l)
1:11
33.07 lb. (15 kg)
1:10
36.38 lb. (16.5 kg)
1:9
40.34 lb. (18.3 kg)
Cylinder
Cylinder diameter, in. (mm)
25.59 (650)
Cylinder depth, in. (mm)
19.69 (500)
Cylinder volume, ft.3 (l)
5.83 (165)
Cabinet
Overall height, in. (mm)
47.32 (1202)
Overall width, in. (mm)
30.71 (780)
Overall depth, in. (mm)
37.09 (942)
Front Loading
Door opening size, in. (mm)
11.81 (300)
Height of door bottom above floor, in (mm)
14.78 (376)
Height of door center above floor, in (mm)
23.82 (605)
Speed
10-50 tr/min - RPM
Wash
85 tr/min - RPM
Distribution
250-1000 tr/min - RPM
Spin
G-factor
363
High Spin
Motor (3 phase), 4p, 1470 tr/min
2.01 HP/1.5 kW
2 (51)
Drain Valve, in. (mm)
Water Supply (hard, soft, warm water), in. (mm)
.75 (19)
Direct Steam Heating
Steam inlet connection size, in. (mm)
.38 (10)
Electrical
Electrical Heating (230/400 V)
12 kW - 15 kW - 18 kW
Electrical Heating (400V)
21 kW - 24 kW
Steam
Not Applicable
Warm Water (without additional heating)
Not Applicable
Warm Water (with additional heating)
Not Applicable
Packing Dimensions (height X width X depth), in. (mm)
51.57 X 33.46 X 42.52
(1310 X 850 X 1080)
Weight
Net weight, lb. (kg)
789.25 (358)
Gross weight, lb. (kg)
855.39 (388)
19
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
Machine Dimensions - Model IHC035
8.66 in.
(220 mm)
46.3 in. (1176 mm)
14.78 in.
(376 mm)
47.32 in. (1202 mm)
3.47 in.
(88 mm)
1.34 in.
(34 mm)
1.34 in.
(34 mm)
2.6 in.
(66 mm)
25.51 in.
(648 mm)
2.6 in.
(66 mm)
30.71 in.
(780 mm)
1.44 in.
(36.5 mm)
CHM2216N
CHM2216N
36.06 in. (916 mm)
CHM2217N
CHM2217
2
7.93 in. (202 mm)
1.44 in.
(36.5 mm)
33.86 in. (860 mm)
3.23 in.
(82 mm)
13.05 in.
(332 mm)
10.49 in. (267 mm)
30.12 in. (765 mm)
3
4.13 in. (105 mm)
4
5
1
6
1.38 in.
(35 mm)
33.17 in.
(843 mm)
2.76 in.
(70 mm)
20.87 in.
(530 mm)
36.81 in.
(935 mm)
35.16 in.
(893 mm)
9
38.11 in.
(968 mm)
4.3 in.
(109.2 mm)
10
8
1
2
3
4
5
7
2.36 in.
(60 mm)
7.87 in.
(200 mm)
Ventilation Soap Dispenser
Warm Water Connections .75 in.
Soft Water Connections .75 in.
Ventilation Tub
Main Switch
CHM2218N
6
7
8
9
10
Electrical Connections
Drain Valve
Steam Connections
Hard Water Connections .75 in.
Liquid Soap Connections
Figure 10
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
20
Washer-Extractors
Mounting Bolt Hole Locations - Model IHC035
1.44 in.
(36.5 mm)
32.99 in.
(838 mm)
30.12 in.
(765 mm)
ø0.71 in.
(ø18 mm)
1.44 in.
(36.5 mm)
2.58 in.
(66 mm)
25.51 in.
(648 mm)
2.62 in.
(66 mm)
30.71 in.
(780 mm)
CHM2219N
CHM2219N
Figure 11
21
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52
Washer-Extractors
WARNING
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
Electrical Installation Requirements - Model IHC035
Boiler Fed/Steam Heat
3
3+PE
6
15
10
14/2.5
P
380-415
50/60
3
3+N+PE
18
20
20
12/4.0
Q
200-240
50/60
3
3+PE
18
20
20
12/4.0
X
200-240
50/60
1/3
2/3+PE
18
20
20
12/4.0
6x3 kW
AWG/mm2
50/60
Recommended
Circuit Breaker
(US-market)
440-480
Full Load
Amps
N
kW Standard
Heating Elements
NON-US
AWG/mm2
Recommended
Circuit Breaker
(US-market)
Full Load
Amps
Wire
Phase
Cycle
Voltage
Code
US
Electric Heat
US
NON-US
32
40
40
8/10.0
44
50
50
8/10.0
63
70
70
4/25.0
63
70
70
4/25.0
Alternative Electric Heat Options
23
30
32
10/6.0
36
40
40
8/10.0
49
60
60
6/16.0
2/3+PE
N/A
N/A
N/A
N/A
3
3+PE
28
40
40
8/10.0
50/60
3
3+N+PE
40
50
50
8/10.0
200-240
50/60
3
3+PE
56
60
60
6/16.0
X
200-240
50/60
1/3
2/3+PE
56
60
60
6/16.0
N
440-480
50/60
3
3+PE
36
40
40
8/10.0
P
380-415
50/60
3
3+N+PE
49
60
60
6/16.0
Q
200-240
50/60
3
3+PE
N/A
N/A
N/A
N/A
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
41
50
50
8/10.0
P
380-415
50/60
3
3+N+PE
53
60
60
6/16.0
Q
200-240
50/60
3
3+PE
N/A
N/A
N/A
N/A
X
200-240
50/60
1/3
2/3+PE
N/A
N/A
N/A
N/A
N
440-480
50/60
3
3+PE
P
380-415
50/60
3
3+N+PE
Q
200-240
50/60
3
3+PE
X
200-240
50/60
1/3
N
440-480
50/60
P
380-415
Q
6x2 kW
3x3 kW
+
3x2 kW
3x3 kW
+
3x4 kW
6x4 kW
Table 5
5-08-52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
22
Washer-Extractors
Installation - IHC Models
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
SW020
Surface
The machine must be securely fixed on a flat surface
(metal base, concrete or solid ground). The anchoring
is to be done on the 6 provided places in the holes on
the corner of the base. (See Mounting Bolt Hole
Locations). Refer to Figure 12.
CHM2102N
1
CHM2102N
1
Mounting Bolt Holes
Figure 12
The machine must be placed entirely level. For easy
maintenance it is recommended to keep a minimal
distance of 23.62 in. (600 mm) between the wall and
the back of the machine.
If several machines are placed next to each other, there
should be a minimal distance of 1.18 in. (30 mm)
between each machine.
IMPORTANT: The bolt pattern for the fixation of
the IHC012 machine is located in the back panel of
the cabinet. Put this panel on the floor and mark
the holes.
23
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5-08-52