Download Baumatic BZE290SS User manual

BZE290SS
Freezer
USER MANUAL FOR YOUR BAUMATIC
BZE290SS freezer
You will be mine
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference. for
you or any person not familiar with the operation of the appliance.
DD 05/10/06
2
Contents
Environmental note
4
Important safety information
5–6
Specifications of your freezer
Description of the appliance
7
8
Using your Baumatic freezer
Before switching on
During first use
Control panel
Turning on the appliance and setting the thermostat
The digital display
9
9
9
10
11
12
Your
freezer
Freezing fresh food
Tips on freezing
Storing commercially frozen food
Defrosting frozen
Fast freeze function
Making ice cubes
Freezer alarm
Defrosting your freezer
12
13
13-14
14
15
15
16
16
17
Cleaning and maintenance
Replacing the light bulb
17
18
Installation
Electrical connection
Positioning
Reversing the door of your appliance
18
18-19
19-20
21-22
Troubleshooting
22-24
Baumatic Ltd. Conditions of Guarantee
25
Contact details
26
3
Environmental note
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
4
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Technical
Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
Use of the appliance
o Your appliance is only designed to be used in the
home. It is suitable for freezing and storing frozen
food. If it is used for any other purpose or it is not
used correctly, then Baumatic Ltd. Will accept no
liability for any damage that may be caused.
o Altering the specification of the appliance must not be attempted
for reasons of safety.
Before using your appliance
o Check the appliance for any signs of transport damage. If you
notice any damage, then you should not connect your appliance
to your mains supply and should contact your retailer.
Refrigerant
o Your appliance contains R600a refrigerant, which is a natural gas
that does not contain CFCs that can damage the environment.
However it is a flammable substance, therefore care should be
taken:
ƒ During the transportation and installation of the
appliance, make sure that the refrigeration pipework
does not get damaged.
ƒ If it does become damaged then sources of ignition
and open flames should be avoided. Also the room
that the appliance is situated in should be thoroughly
ventilated.
o Do not place any objects on top of the appliance,
as this may damage the table top.
5
Child safety
o Packaging material should be kept away from
children.
o Children should not be allowed to touch the
controls or play with the appliance.
General safety
o Do not pull on the power supply cable to remove the plug from
your mains supply socket.
o Do not pull out or insert the plug with wet hands.
o Do not attempt to use your appliance outdoors or
any place where it is likely to come into contact
with the elements.
o Before cleaning the appliance or performing
maintenance work, ensure that the appliance has been
disconnected from your mains supply.
o Never allow the back coils of the appliance to come into contact
with the wall surface.
o Always ensure that the location where you are installing your
appliance is free of stored items such as papers and other
flammable materials.
o Never block the ventilation openings of the appliance, either on
the inside or its exterior.
o It is vital to keep your appliance well ventilated,
so that there is proper air flow between the
bottom of the unit and the plinth/kick plate
which it is sitting on.
o Do not place electrical devices inside of the appliance, such as
mixers and electric ice cream makers.
Service
You should not attempt to repair the appliance
yourself, as this could cause injury or a more serious
malfunction. If you require a service call then please
contact the Baumatic Service Department.
6
Specifications of your freezer
Congratulations on purchasing a Baumatic freezer.
o Frost free freezer
o Adjustable thermostat
o Electronic control
o Bacteria safe system
o Fast freeze function
o Temperature rise warning indicator
o Open door warning indicator
o 8 Freezer drawers
o Reversible door
o Adjustable feet
o Stainless steel front and sides
Dimensions of appliance*
Height:
Width:
Depth:
1800 mm
600 mm
640 mm
Energy efficiency class
Energy class:
A
* Please refer to the installation instructions for more specific
information on the size of aperture that you will require.
IMPORTANT: When you install your appliance it is important to bear
in mind its climatic rating.
In order to find out the climatic rating of your appliance, you should
check the rating plate. The rating plate is located on the front left edge
of the inside of the fridge section. You will need to open the door of
your appliance to be able to find it.
The rating plate will indicate the ambient temperature range that your
appliance will function correctly within.
7
Description of the appliance
1.
2.
3.
4.
5.
6.
7.
Control panel & thermostat control
No frost freezing unit
Interior illumination
Freezing and storage drawers
Large storage drawer
Adjustable feet
Wheels
o The freezer drawers are protected against accidental extraction.
o To remove a drawer from the appliance, open it and lift the front
part upwards. Then pull it out.
o Certain models are fitted with pull out slide guides which
facilitate opening.
o Pull out guide drawers are extracted by lifting the rear end and
pulling out at an angle under 45 degrees. You need to reinsert
them the opposite way, to put a pull out guide drawer back into
position.
8
Using your Baumatic freezer
Before switching on
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o After delivery, wait for eight hours before connecting the
appliance to your mains supply. This will allow any refrigerant
gasses that may have been disturbed during the transportation
process, are allowed to settle.
o The outside of the appliance and the removable accessories
contained within it, should be cleaned with a solution of liquid
detergent and water.
o The interior of the appliance should be cleaned
with a solution of sodium bicarbonate dissolved in
lukewarm water. The interior and accessories
should be thoroughly dried, after the cleaning
process has been completed.
o There can be an odour when you first switch on the appliance. It
will lessen as the appliance starts to cool.
During first use
o When you first switch on the appliance, the compressor will run
continuously for approximately 24 hours or until the refrigerator
reaches a cool enough temperature.
o During this period of time, you should try not to open the door
frequently or place a large amount of food within the appliance.
o If the unit is switched off or unplugged, you must allow at least 5
minutes before restarting the appliance on the thermostat or
connecting it to your mains supply.
9
Control panel
(Model with buttons)
(Model without buttons)
o A: Temperature selector and on/off button
o B: Green LED (illuminates when the appliance is switched on)
o C: Freezer alarm off button (model with buttons only)
o D: Freezer alarm LED
o E: Fast Freeze button (model with buttons only)
o F: Fast Freeze LED
o G: Digital freezer temperature display. Indicates the actual
freezer temperature inside the appliance, from -16°C to -24°C*
* Certain models only.
10
Turning on the appliance and setting the thermostat
You switch on your appliance by connecting it to your
mains supply and setting the thermostat. The
thermostat is located on the right hand side of the
control panel.
o The appliance is switched on by turning dial A
towards the Max position.
o The green LED will come on when the dial moves
past Min.
o The appliance is switched off when the arrow on
.
the dial points to the ON/OFF symbol
However the appliance is still under mains power.
o The thermostat automatically regulates the temperature inside
the freezer, depending on what position you have turned the
thermostat control knob to.
o Position
cool.
means that the appliance is switched off and will not
o Position Min will give you a higher temperature inside the
freezer.
o Position Max will give you a lower temperature inside the
freezer.
o Ideally the thermostat should be set to the Eco position.
o The freezer section can cool down to -18°C and lower.
o IMPORTANT: The ambient temperature of the room,
the temperature of food and the amount of food that
has been placed in the freezer and how often the door is
opened, will all affect the temperature being maintained
by the appliance.
o On the maximum setting (position Max), your freezer will work
harder to maintain a lower temperature. There is no need to run
your appliance on this setting for prolonged periods and you
should return the thermostat knob to the Eco position.
11
The digital display
o On models with a digital display, when you
are adjusting the thermostat position, the
display will flash and indicate the set
temperature.
o When the flashing stops, the setting of the
temperature is complete and it is stored in
the appliance’s memory.
o Please allow time for the appliance to
reduce down to the desired temperature.
o Each time the appliance is switched on for the first time, the
digital display (G) indicates a temperature of -16°C and flashes.
o This value will remain on the display until the actual temperature
in the appliance drops below -16°C.
o The flashing will then stop and the digital display will indicate the
actual temperature within the freezer.
The
freezer compartment
The freezer compartment is suitable for storing and freezing food.
o The freezer compartment temperature must have already
reached -18 degrees centigrade (or lower) before you attempt to
store food that is already frozen or freezing fresh food.
o The freezer compartment is only able to freeze a certain quantity
of food at one time. You should not attempt to freeze more than
25 kilograms of fresh food within a 24 hour period.
o Your appliance allows freezing in all drawers, but not more than
7 kg in any particular drawer, and 4 kg in the bottom drawer.
o Warm food should be allowed to cool down before you attempt
to freeze it. If you place warm food in the freezer compartment,
then the increased humidity will cause quicker ice formation and
increase the amount of power that the appliance uses.
o The guidance of the food manufacturer should be followed, in
regard to the maximum storage time.
o Thawed foods must not be frozen for a second time.
o Do not let the already frozen packages touch the fresh ones.
12
Freezing fresh food
o To freeze the maximum quantity of fresh food
specified above, you should activate the Fast
Freeze function 24 hours prior to attempting
freezing.
o For smaller quantities of fresh food, you
should activate the Fast Freeze function
approximately 6 hours prior to attempting
freezing.*
*For more information on the Fast Freeze function, please see the
“Setting the Fast Freeze function”
o Fresh food should be packed into airtight containers
or packaging. This will help to make sure that the
food doesn’t dry out or lose its flavour. It will also
ensure that flavour does not transfer from other
foods.
o The food should be placed on the
freezer compartment’s base. Do not
allow fresh food to touch items that
are already frozen.
o After 24 hours you should check that
the fresh food is satisfactorily frozen.
If it is then the fast freeze function
should be switched off.
Tips on freezing
o Freezer bags, polythene wraps, aluminium foil (extra thick) and
special cans for frozen foods are suitable packaging for storing
frozen goods in.
o Tape, rubber bands or plastic clips are
suitable for sealing bags and wrappings.
o Before sealing a suitable bag, you should
compress the air out of it, as this will help
the food to freeze more easily.
o Flat packages freeze more easily.
13
o If you are freezing liquid, then do not fill the
container to the brim. Liquids will expand when
being frozen.
o Do not place bottles (glass or tin)
containing liquids (especially sparkling
liquids) into the freezer as they could
cause the bottle to burst during freezing.
Storing commercially frozen food
o The storage time and recommended temperature for storing
commercially frozen foods, are indicated on the packaging.
o Always follow the manufacturer’s instructions for storage and
use of frozen food.
o When shopping, be careful to choose food which is adequately
packed and is provided with complete storage instructions. It
should have been stored in a freezer where the temperature
does not rise above -18°C.
o Do not buy packages of food that are covered with frost. This
could indicate that the package has thawed at least once before.
o Take care that your frozen food packages do not start to thaw
before you place them in your freezer. This will shorten the
length of time that you can safely store the food for.
14
Defrosting frozen food
o Partially thawed or defrosted foods should be used as soon as
possible.
o Cold air preserves the food but it does not destroy the micro
organisms which rapidly activate themselves after defrosting and
make foods perishable.
o Partial defrosting reduces the nutritional value of food, especially
fruits, vegetables and readymade meals.
Fast freeze function (Model with buttons)
o To activate the fast freeze function, press button
E.
o The orange LED light (F) will come on.
o To turn off the fast freeze function, again press
button E.
o The orange LED light (F) will turn off.
o If the fast freeze function is not switched off,
then it will do so automatically after
approximately 50 hours.
(Model with no buttons)
o Turn the thermostat dial (A) to the SF
position.
o The orange LED light (F) will come on.
o To turn off the fast freeze function, turn the
thermostat dial (A) back to the ECO position.
o The orange LED light (F) will turn off.
o If the fast freeze function is not switched off,
then it will do so automatically after
approximately 50 hours.
o To repeat the fast freeze function if it switches off automatically,
you will need to turn the dial back to the ECO position and then
back to the SF position. The orange LED light (F) will come back
on.
15
Making ice cubes
o Remove the cap from the ice tray and fill it to the indicating
mark with cold water or some other liquid, suitable for freezing.
o Close it and place it in the door shelf. The ice tray can produce 8
cubes.
o The period required for ice to form is 2-6 hours. It is
recommended to make a quantity of ice, prior to the time that
you require it.
o Ice cubes are discharged from the tray by turning the tray
upside down and placing it under cold running water.
o Shake the tray, open the cover and pour the ice out.
Freezer alarm
o The red signal light (D) indicates that the appliance has sensed
an excessive rise in temperature.
o The light goes off automatically when the freezer cools to a
temperature where there is no longer a danger to the food being
stored in the appliance.
o When the appliance is first switched on, there is an inbuilt 24
hour delay to the freezer alarm switching on. This will prevent
the alarm triggering unnecessarily whilst the appliance is getting
down to working temperature.
(Model with buttons)
o These models also have an audible alarm, in
the form of an intermittent beep, as well as
the red light.
o The alarm can be cancelled by pressing button
(C).
o The alarm will sound every 24 hours, if the
temperature in the freezer is still not low
enough to safely store food.
16
Defrosting your freezer
o Your appliance is frost free, so there is no need to defrost it
manually.
o You may occasionally see the appearance of a frost layer, but
over a period of time the frost free system will remove it.
Cleaning and maintenance
WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR MAINS SUPPLY BEFORE
ATTEMPTING TO CLEAN IT.
o Do not clean the appliance by pouring water onto
it or spraying water over it.
o The freezer compartment should be cleaned
periodically, using a solution of bicarbonate of soda
and lukewarm water.
o Clean the accessories separately with soap and water.
Do not clean them in a dishwasher.
o Do not use abrasive products, detergents or soaps.
o After washing the appliance, wipe over the area that you have
cleaned with a damp cloth and then dry it thoroughly.
o When cleaning is complete, dry your hands and then reconnect
the plug to your mains supply.
17
Replacing the light bulb
WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR MAINS SUPPLY BEFORE
ATTEMPTING TO REPLACE THE LIGHT
BULB.
o Remove the plastic cover and replace the bulb with a new one.
o The bulb that you should use is an E14 max, which is the same
as the bulb originally fitted by the factory.
o Please dispose of the bulb correctly.
o The light bulb is not covered by Baumatic’s guarantee.
Installation
IMPORTANT: Before installation and usage,
read all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found on the front left edge of the
inside of the refrigerator.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR REFRIGERATOR IS INTENDED FOR FITTED
AND PERMANENT INSTALLATION.
We recommend that the appliance is connected by a
qualified electrician, who is a member of the N.I.C.E.I.C.
and who will comply with the I.E.E. and local regulations.
o Your refrigerator comes supplied with a 13 amp plug fitted. If in
future you need to change the fuse in this plug, then a 13 amp
ASTA approved (BS 1362) fuse must be used.
o The wiring in the mains lead is coloured as follows:
Brown
Live
Blue
Neutral
Green and yellow
Earth
18
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
The brown wire must be connected to the terminal marked “L”
(live), or coloured red.
The blue wire must be connected to the terminal marked “N”
(neutral), or coloured black.
The green and yellow wire must be connected to the terminal
marked “E” (earth), or by the earth symbol, or coloured green
and yellow.
o When the connection is completed, no stray strands or cut wire
should be present. The cord clamp must be secured over the
outer sheath.
Positioning
o It is advisable that your appliance is only installed in a location
where the ambient temperature of the room, corresponds with
the climate classification that is stated on the rating plate of your
appliance. Your appliance may not function correctly if the
ambient temperature falls outside of the following ranges.
Climate classification Appropriate ambient temperature
SN
+10 to +32 degrees centigrade
N
+16 to +32 degrees centigrade
ST
+10 to +38 degrees centigrade
T
+18 to +43 degrees centigrade
o Positioning the appliance requires two persons in order to avoid
injuries or damage to the appliance.
o Your appliance should not be located in direct sunlight or
exposed to continuous heat or extremes of temperature (e.g.
next to a radiator or boiler).
o You should check whether there is an electrical socket available,
which will be accessible after your appliance is installed.
o Place the appliance flatly and firmly on a solid base. The
appliance is fitted with adjustable feet on the front side, used to
level the appliance.
o The rear side of the appliance is fitted with wheels which
facilitate the positioning of the appliance into its final location.
19
o Anything positioned above the appliance must be at least 5 cm
away to allow sufficient cooling of the condenser. You must allow
a 15mm gap to the rear of the appliance.
o Avoid exposing the appliance to direct sunlight or heat sources.
If this is not feasible, then you should install an insulation plate
between the appliance and the adjacent heat source.
o The bottom front corners of your appliance are fitted with
handles to facilitate moving. The appliance may stand
independently or adjacent to a cupboard or wall.
o Be sure to leave enough space for the opening of the door, to
avoid damage to the appliance or personal injury. Also leave
ample space for extracting shelves. (see diagram on the next
page).
20
Reversing the door of your appliance
Caution! After unscrewing any of the fixing
hinges, hold the door to prevent it from falling
and causing damage.
Any parts that you remove from the appliance
whilst reversing the door, should be retained for
later use.
Required tools; socket spanner number 8, screwdriver, torque
25.
o Remove the upper hinge cover from both sides of the appliance.
o WHILST SUPPORTING THE DOOR, unscrew upper hinge
screws and remove the upper door from the middle hinge.
o On the bottom side of the upper door unscrew the swing stopper
screws and remove the stopper (A). Fix the attached stopper
with its bearing on the opposite side of the door.
o Unscrew the forced door closure system (B) and fix it to the
opposite side of the door (certain models only).
o Unscrew the middle hinge
screws and remove the
door from the bottom
hinge.
o Unscrew the leg holder
fixing screws.
21
o Tilt the appliance backward at a maximum angle of 35°. Unscrew
the leg support screws (C) - left and right, and remove the leg
support cover (D). Then place it on the opposite side.
o Unscrew, remove and then replace the position of the end switch
(E) and decorative peg (F) (for models with forced door closing
system).
o Unscrew the three screws fixing the bottom hinge and then fix
the bottom hinge on the opposite side.
o To fit the door on the opposite side of the freezer proceed with
the above procedure in reverse.
Troubleshooting
IMPORTANT: If your freezer appears not to be
operating properly, before contacting the Baumatic
Service Department, please refer to the checklist
below.
My freezer does not appear to be working/there is no
power to my appliance.
o Check that the plug is fully inserted into the power socket.
o Check that there is power to your mains supply (e.g. that there
hasn’t been a power cut or that the fuse hasn’t blown).
o Check that the thermostat inside the appliance has not been
turned to the off position.
o Check that your mains supply voltage, corresponds to the
voltage stated on the rating plate of your appliance.
My freezer appears to be performing poorly
o Check that the appliance isn’t overloaded and that food hasn’t
been packed too tightly into it.
22
o The thermostat setting is too low, you should turn the
thermostat up higher.
o Ensure that the door is closing properly and that the door has
not been opened for a prolonged period in error.
o Ensure that there is adequate ventilation for your appliance.
My freezer is noisy
o The refrigerant gas that circulates the pipework of the appliance
may make a slight noise, even if the compressor is not running.
o If the noise worsens or the appliance gets louder than normal;
check that it is leveled off correctly, that nothing is touching the
rear of the fridge and that nothing placed inside the appliance is
rattling.
Ice is forming inside my frost free freezer
o Check that food has not been pushed too far back inside the
appliance, so that it is in contact with the inner back wall.
o Check that the door is sealing correctly. Clean or replace the
door gasket if it is dirty or damaged.
o Frequent opening of the door or the door is being left open for
too long.
o Inserting hot food in the freezer.
The red warning light keeps coming on
o Frequent opening of the door or the door is being left open for
too long.
o Door not closing properly, check that the door gasket is sealing
properly.
o There has been a long power failure on your mains supply
o An excessive quantity of fresh food has been inserted at once.
The door is difficult to open
o If you attempt to open the door immediately after you have just
closed it, you may experience some resistance. This happens
because a certain quantity of cold air escapes from the appliance
through the open door and is replaced by warm ambient air.
o Cooling of such air creates negative pressure (a vacuum) and
suction, which prevents easy opening of the door. This will
23
normalise after several minutes and you should be able to open
the door with ease again.
The green LED is flashing
o Contact the Baumatic Service Department on telephone number
0118 933 6911.
An error code of E1 appears on the digital display
o Contact the Baumatic Service Department on telephone number
0118 933 6911.
Troubleshooting helpful hint
o If the above hints do not seem to cure the difficulty that you are
facing, then you should turn the thermostat dial to the off
position and disconnect the power cord from your mains supply.
o Wait ten minutes and then reconnect the appliance to your
mains supply and turn the thermostat dial back to it’s normal
operating position (ECO).
If your appliance is still not working
correctly, then please contact the Baumatic
Service Department on telephone number
0118 933 6911.
24
Baumatic Ltd. Conditions of Guarantee
Dear Customer,
Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and
labour costs resulting from defective materials or workmanship.
Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12
months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period
applies to England, Scotland, Wales and Northern Ireland only.
To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase
to be covered under this guarantee. This can be done online via: www.baumatic.co.uk or through returning
the guarantee card which can be found in each new Baumatic appliance.
* In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of
charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any
defect that arises due to faulty materials or workmanship within a period of 5 years from the original
purchase date.
* An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the
warranty period.
Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the
policy is negated and Baumatic Ltd will be under no further liability.
The guarantee covers the appliance for normal domestic use only, unless otherwise stated.
Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale
issued at the time of purchase.
This guarantee is transferable only with the written consent of Baumatic Ltd.
If the appliance fails and is considered either not repairable or uneconomical to repair during the
manufacturer warranty period, a free of charge replacement will not be offered.
The guarantee for any replacement will only be for the remainder of the guarantee on the original product
purchased.
The guarantee does not cover:
- Sinks and taps
- Failure to comply with the manufacturers instructions for use.
- The replacement of cosmetic components of accessories
- Accidental damage or wilful abuse.
- Subsequent loss or damage owing to the failure of the appliance or electrical supply
- Incorrect installation
- Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts
- Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers,
baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals.
In the course of the work carried out it may be necessary to remove the appliance from it operating
position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage
sustained to any property whatsoever in this process.
This guarantee is in addition to and does not diminish your statutory or legal rights.
Contacting Baumatic Ltd
Service
Spares
Sales
TEL: 0118 933 6911
TEL: 0118 933 6922
TEL: 0118 933 6900
FAX: 0118 986 9124
FAX: 0118 933 6942
FAX: 0118 931 0035
For ROI (Republic of Ireland), please contact one of the numbers below:
TEL: 01 – 6266798
FAX: 01 - 6266634
Technical/Advice
0118 933 6933
0118 933 6942
Thanks you for buying Baumatic.
* Applies to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year labour & 1 year parts warranty only)
25
Baumatic Ltd
You will be mine
Headquarters
Baumatic Ltd.
Baumatic Buildings,
6 Bennet Road,
Reading,
Berkshire
RG2 0QX, United Kingdom
Sales Telephone
+44 118 933 6900
Sales Fax
+44 118 931 0035
Service Telephone
+44 118 933 6911
Service Fax
+44 118 986 9124
Spares Telephone
+44 118 933 6922
Technical / Advice Telephone
+44 118 933 6933
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Http (Internet site):
www.baumatic.com
26
27