Download repair parts catalog for sunnen® power stroked precision honing
Transcript
REPAIR PARTS CATALOG FOR SUNNEN® POWER STROKED PRECISION HONING MACHINE MODEL: MBC-1805 THIS CATALOG COVERS THE ABOVE MODEL BEGINNING WITH SERIAL NO. 96110. “SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN® PRODUCTS COMPANY.” SUNNEN® PRODUCTS COMPANY 7910 MANCHESTER AVENUE • ST. LOUIS, MO 63143, U.S.A. • PHONE: 314-781-2100 X-MBC-5046 Like any machinery, this equipment may be dangerous if used improperly. Be sure to read and follow instructions for operation of equipment. INTRODUCTION Illustrations show all major components in exploded detail. Item numbers on each illustration are keyed to the corresponding parts list, providing a descriptive identification of each part. The parts lists include assemblies as well as detail parts. An item listed without a part number can be obtained as a component of the complete assembly of which it is a part. Standard hardware items are listed with complete descriptions, such as Item 29 below. These may be purchased at your local hardware store, but it is important to replace an item with one having the same dimensions as the original. In some places brand names and part numbers are shown. These may change depending upon availability. Sunnen® Products Company reserves the right to make changes, without notice, to materials, specifications, colors, designs and accessories included with units. HOW TO ORDER When ordering replacement parts be sure to include the following information to ensure prompt shipment of correct parts: 1. The part number and description of each part desired, obtained from this parts catalog. 2. The quantity of each part desired. 3. The voltage, frequency and phase, when ordering electrical parts. 4. The model and serial number of the machine, obtained from the name plate, where there is any question concerning a part. HOW TO USE THIS PARTS LIST Step 1. – Locate desired part on illustration. Note item number. Step 2. – Locate item number in the parts list. Step 3. – If the item has a part number listed, order by part number and the description. A part number in light face type indicates that it is a component of the last preceding part number in bold face type. Step 4. – If no number is listed, order the part number of the unit of which the desired part is a component. ORDER ONLY BY PART NUMBER AND DESCRIPTION – NOT by item number. NOTE: In this manual, parts may be followed by “(For CE Machines)” or “(For Non-CE Machines)” to denote domestic machines from exported machines. The CE version is constructed to meet the requirements of the European market, and is available to any customer. 1 Step 1. 4 2 3 15 17 14 Step 2. Step 3. Step 4. ITEM NO. ORDER BY PART NUMBER QTY. 1 2 3 4 MVH-4499A PHSM-405 PHW-354 MVH-4422 1 3 3 1 ....Spindle Cap includes ......Screw (M6 x 1 x 16 SHCS) ......Washer (M6) ....Inner Spindle Nose 14 15 16 17 PEM-870A PEM-871 PEM-872 PHSM-600 1 1 1 1 ....Cable Carrier includes ......Cable Carrier Bracket ......Cable Carrier Bracket ....Screw (M3 x 0,5 x 5mm FHCS) iii DESCRIPTION GENERAL INFORMATION The Sunnen® equipment has been designed and engineered for a wide variety of parts within the capacity and limitation of the equipment. With proper care and maintenance this equipment will give years of service. READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE UNPACKING, INSPECTING, OR INSTALLING THIS EQUIPMENT. IMPORTANT: Read any supplemental instructions BEFORE installing this equipment. These supplemental instructions give you important information to assist you with the planning and installation of your SUNNEN® equipment. Sunnen Technical Service Department is available to provide telephone assistance for installation, programming, & troubleshooting of your Sunnen equipment. All support is available during normal business hours, 8:00 AM to 4:30 PM Central Time. Review all literature provided with your Sunnen equipment. This literature provides valuable information for proper installation, operation, and maintenance of your equipment. Troubleshooting information can also be found within the Instructions. If you cannot find what you need, call for technical support. Where applicable, programming information for your Sunnen equipment is also included. Most answers can be found in the literature packaged with your equipment. Help us help you. When ordering parts, requesting information, or technical assistance about your equipment, please have the following information available: • Have ALL MANUALS on hand. The Customer Services Representative or Technician will refer to it. • Have Model Number and Serial Number printed on your equipment Specification Nameplate. • Where Applicable: Have Drive model and all nameplate data. Motor type, brand, and all nameplate data. For Troubleshooting, additional information may be required: • Power distribution information (type - delta, wye, power factor correction; other major switching devices used, voltage fluctuations) • Installation Wiring (separation of power & control wire; wire type/class used, distance between drive and motor, grounding). • Use of any optional devices/equipment between the Drive & motor (output chokes, etc.). For fast service on your orders call: Sunnen Automotive Customer Service toll free at: 1-800-772-2878 Sunnen Industrial Customer Service toll free at: 1-800-325-3670 Customers outside the USA, contact your local authorized Sunnen Distributor. Additional information available at: http://www.sunnen.com or e-mail: sunnen@sunnen.com NOTE: Sunnen reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing. Should any discrepancy of information arise, Sunnen recommends that user verify the discrepancy with Sunnen before proceeding. ESD PREVENTION REVIEW Let's review the basics of a sound static control system and its effective implementation. First, in the three step plan: 1. Always ground yourself when handling sensitive components or assemblies. 2. Always use a conductive or shielded container during storage or transportation. These materials create a Faraday cage which will isolate the contents from static charges. 3. Open ESD safe containers only at a static safe work station. At the static safe work station, follow these procedures before beginning any work: A. Put on your wrist strap or foot grounding devices. B. Check all grounding cords to make sure they are properly connected to ground, ensuring the effective dissipation of static charges. C. Make sure that your work surface is clean and clear of unnecessary materials, particularly common plastics. D. Anti-static bubble wrap has been included for use at the machine when an ESD safe workstation is not available. You are now properly grounded and ready to begin work. Following these few simple rules and using a little common sense will go a long way toward helping you and your company in the battle against the hazards of static electricity. When you are working with ESD sensitive devices, make sure you: GROUND ISOLATE NEUTRALIZE iv SUNNEN® LIMITED PRODUCT WARRANTY SUNNEN® Products Company and its subsidiaries (SPC) warrant that all new SPC honing machines, gaging equipment, tooling, and related equipment will be free of defects in material and/or workmanship for a period of one year from the date of original shipment from SPC. Upon prompt notification of a defect during the one-year period, SPC will repair, replace, or refund the purchase price, with respect to parts that prove to be defective (as defined above). Any equipment or tooling which is found to be defective from improper use will be returned at the customer's cost or repaired (if possible) at customer's request. Customer shall be charged current rates for all such repair. Prior to returning any SPC product, an authorization (RMA#) and shipping instructions must be obtained from the Customer Service Department or items sent to SPC will be returned to the customer. Warranty Limitations and Exclusions This Warranty does not apply to the following: • Normal maintenance items subject to wear and tear: (belts, fuses, filters, etc). • Damages resulting from but not limited to: › Shipment to the customer (for items delivered to customer or customer's agent F.O.B., Shipping Point) › Incorrect installation including improper lifting, dropping and/or placement › Incorrect electric power (beyond +/- 10% of rated voltage) including intermittent or random voltage spikes or drops › Incorrect air supply volume and/or pressure and/or contaminated air supply › Electromagnetic or radio frequency interference from surrounding equipment (EMI, RFI) › Storm, lightning, flood or fire damage › Failure to perform regular maintenance as outlined in SPC manuals › Improper machine setup or operation causing a crash to occur › Misapplication of the equipment › Use of non-SPC machines, tooling, abrasive, fixturing, coolant, repair parts, or filtration › Incorrect software installation and/or misuse › Non-authorized customer installed electronics and/or software › Customer modifications to SPC software THE LIMITED WARRANTY DESCRIBED HEREIN IS EXPRESSLY IN LIEU OF ALL ANY OTHER WARRANTIES. SPC MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS OR IMPLIED, WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER. SPC IS NOT RESPONSIBLE FOR THE IMPROPER USE OF ANY OF ITS PRODUCTS. SPC SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO: LOSS OF USE, REVENUE, OR PROFIT. SPC ASSUMES NO LIABILITY FOR PURCHASED ITEMS PRODUCED BY OTHER MANUFACTURERS WHO EXTEND SEPARATE WARRANTIES. REGARDLESS OF ANY RIGHTS AFFORDED BY LAW TO BUYER, SPC's LIABILITY, IF ANY, FOR ANY AND ALL CLAIMS FOR LOSS OR DAMAGES WITH RESPECT TO THE PRODUCTS, AND BUYER'S SOLE AND EXCLUSIVE REMEDY THEREFORE, SHALL IN ALL EVENTS BE LIMITED IN AMOUNT TO THE PURCHASE PRICE OF THAT PORTION OF THE PRODUCTS WITH RESPECT TO WHICH A VALID CLAIM IS MADE. Shipping Damages Except in the case of F.O.B., Buyer's destination shipments, SPC will not be liable for any settlement claims for obvious and/or concealed shipping damages. The customer bears the responsibility to unpack all shipments immediately and inspect for damage. When obvious and/or concealed damage is found, the customer must immediately notify the carrier's agent to make an inspection and file a claim. The customer should retain the shipping container and packing material. SUNNEN® SOFTWARE LICENSE AGREEMENT This document is a Legal Agreement between you, as user and licensee (Licensee), and Sunnen® Products Company (SPC) with respect to preprogrammed software (Software) provided by SPC for use on SPC Equipment. By using the Software, you, as Licensee, agree to become bound by the terms of this Agreement. In consideration of payment of the license fee (License Fee) which is part of the price evidenced by your receipt (Receipt), SPC grants to you as Licensee a non-exclusive right, without right to sub-license, to use the particular copy of the SPC Software licensed hereunder only on the particular equipment sold with the Software. SPC reserves all rights including rights not otherwise expressly granted, and retain title and ownership to the Software including all subsequent copies or updates in any media. The Software and all accompanying written materials are covered by copyrights owned by SPC. If supplied on removable media (floppy disk), you, as Licensee, may copy the Software only for back up purposes; or you may request that SPC copy the Software for you for the same purposes. All other copying of the Software or of the accompanying written materials is expressly forbidden and is in violation of the Agreement. The Software and accompanying written materials (including the user's manual, if any) are provided in an "as is" condition without warranty of any kind including the implied warranties of merchantability and fitness for a particular purpose, even if SPC has been advised of this purpose. SPC specifically does not warrant that it will be liable as a result of the operation of the Software for any direct, indirect, consequential or accidental damages arising out of the use of or inability to use such product even if SPC has been advised of the possibility of such use. It is recognized that some states do not allow the exclusion or limitation of liability for consequential or accidental damages and to the extent this is true, the above limitations may not apply. Any alteration or reverse engineering of the software is expressly forbidden and is in violation of this agreement. SPC reserves the right to update the software covered by this agreement at any time without prior notice and any such updates are covered by this agreement. v SAFETY INSTRUCTIONS READ FIRST This machine, like any equipment, may be dangerous if used improperly. Please read all warnings and instructions before attempting to use this machine. Always disconnect power at main enclosure before servicing machine.1 Always wear eye protection when operating this machine. NEVER open or remove any machine cover or protective guard with power "ON." Always disconnect power at main enclosure before servicing this equipment.1 DO NOT attempt any repair or maintenance procedure beyond those described in this book. Contact your Sunnen® Field Service Engineer or Technical Services Representative for repairs not covered in these instructions. Due to the wide variety of machine configurations, all possibilities cannot be described in these instructions. Instructions for safe use and maintenance of optional equipment ordered through Sunnen, will be provided through separate documentation and/or training provided by your Sunnen Field Service Engineer or Technical Services Representative. DO NOT attempt to defeat any safety device on this machine or on any of the optional equipment. If specially built automation components are added to this system, be sure that safety is not compromised. If necessary, obtain special enlarged work area safety system from Sunnen Products Co. Indicates CE version ONLY. 1 DO NOT touch electrical components until main input power has been turned off and CHARGE lamps are extinguished. WARNING: The capacitors are still charged and can be quite dangerous. vi CONTENTS PAGE Introduction .......................................................................................................... How To Order ...................................................................................................... How To Use This Parts List ................................................................................. General Information ............................................................................................. ESD Prevention Review ...................................................................................... Limited Product Warranty .................................................................................... Sunnen Software License Agreement .................................................................. General Safety Instructions .................................................................................. Contents ............................................................................................................... iii iii iii iv iv v v vi 1 HONING MACHINE HEAD A Honing Machine Head & Motor Assembly .......................................................... B Honing Machine Head Assembly ........................................................................ C Automatic Shutoff ................................................................................................ D Stone Saver Assembly ........................................................................................ 2 5 8 10 HONING MACHINE BASE E Base, Filter, Pump & Coolant Assembly ............................................................. F Air Actuated Pedal Depressor ............................................................................. G Coolant Reservoir Unit ........................................................................................ H Foot Pedal Unit .................................................................................................... I Drip Tray & Accessories ...................................................................................... 12 16 19 20 22 POWER STROKER J Power Stroking Attachment ................................................................................. K Arm Assembly ..................................................................................................... L Tube & Shaft Assembly ....................................................................................... M Cross Arm Assembly ........................................................................................... 24 28 31 32 ELECTRICAL SYSTEM N Automatic Size Control ........................................................................................ O Electrical Control Enclosure (For Non “CE” Machines) ....................................... P Electrical Control Enclosure (For Non “CE” Machines)....................................... Q Electrical Control Enclosure (For “CE” Machines) .............................................. R Control Box .......................................................................................................... 33 35 36 38 40 COVERS & GUARDS S Sheet Metal Covers & Latches ............................................................................ 42 T Belt Guard Assembly ........................................................................................... 44 U Work Area Cover ................................................................................................. 46 “SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN® PRODUCTS COMPANY.” © Copyright 2004 by Sunnen® Products Company • Printed in U.S.A. Page 1 SECTION I - HONING MACHINE HEAD FIGURE A - HONING MACHINE HEAD & MOTOR ASSEMBLY Page 2 SECTION I HONING MACHINE HEAD PARTS LIST COVERING FIGURE “A” ITEM NO. 1 1 1 2 3 4 5C 6 6A 6B 6A 7 7A 8 8A 9 10 11 12 13 14 14A 15 16 17 18 19 N/S 20 21 22 23 24 25 N/S 26 27 28 29 30 31 32 33 34 35 36 37 38 38A ORDER BY PART NUMBER QTY. PMO–580A PMO–579A PMO–580H KN-567 KN-568 PEC-103 MBB–2606A MBB–1826A LBN-340 MBB–1846A LBN-340 MBB–1830A MBB-1833A MBB–1815A MBB–1835A MBB–1840A MBB–1850A MBB–1870A UN-18 PHW-120 PHS-686 MBB–1855A KN-523 MBB–1867A PHS-637 MBB–1860A KN-568 LBB-891 PHW-119 MBB–1874A DL-36 MBB–968A LBN-431 MBB–978A MBB-977 PHN-121 MBB-973C PHS-630 MBB-972 MBB-1821 MBB-1823A MSN-277 MBH-396 MBB-985A MBB-976A MBB-2441A MAN-1223 PHS-605 PBR-57A PHS-128 1 1 1 4 4 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 DESCRIPTION ....*Motor (1HP, 208/230/460V, 60Hz, 3Ph, 1745 RPM, 7/8 Dia. Shaft) ....*Motor (1HP, 380/400V, 50Hz, 3Ph, 1450 RPM, 7/8 Dia. Shaft) ....*Motor (1HP, 220/440V, 50Hz, 3Ph, 1450 RPM, 7/8 Dia. Shaft) ....Screw (5/16–18 x 1 Hex Hd. Cap) ....Washer (5/16 Plain) ....Connector includes 4A and 5 ....Guard ....Motor Pulley (60 Hz Machines) with ......Set Screw (1/4–20 x 3/8 Soc. Cup Pt.) ....Motor Pulley (50 Hz Machines) with ......Set Screw (1/4–20 x 3/8 Soc. Cup Pt.) ....“V” Belt (60 Hz Machines) ....“V” Belt (50 Hz Machines) ....Countershaft Pulley (60 Hz Machines) with Bearing ....Countershaft Pulley (50 Hz Machines) with Bearing ....“V” Belt ....Idler Assembly includes ........Idler Release Assembly with ........Washer (5/16 Fiber) ........Spring Washer ........Shoulder Screw (5/16 x 3/8 with 1/4–20 x 7/16 Thd.) ......Idler Arm with ........Set Screw (5/16–18 x 1/2 Soc. Plain Cup Pt.) ......Shoulder Bushing with ........Screw (5/16–18 x 1–1/4 Soc. Flat Hd. Cap) ......Idler Pulley Assembly with ........Washer (5/16 Plain) ........Screw (5/16–18 x 3/4 Soc. Hd. Cap) ........Washer (5/16 Lock) ....Stud with ......Nut (3/8–16 Hex) ....Brake Adjusting Screw with ......Nut (1/4–20 Hex) ....Brake Lever with ........Shoulder Screw (5/16 x 5/8 with 1/4-20 x 7/16 Thd.) ........Locknut (1/4-20 Hex) ....Brake Cam with ......Screw (5/16-18 x 1-1/4 Soc. Hd. Cap) ......Washer (5/16 Serrated Lock) ......Spacer ....Brake Strap with ......Screw (10-32 x 3/8 Rd. Hd.) ......Washer (Bent) ....Brake Rod Assembly with ......Retaining Ring ....Brake Anchor with ......Washer (3/8 Lock) ......Screw (3/8-16 x 1 Soc Hd. Cap) ....Bearing ....Set Screw (10-32 x 1/4 Soc. Nylon Tip) N/S indicates Not Shown *Specify brand name of motor, voltage and hertz if other than as listed. (Parts continued on next page) Page 3 SECTION I HONING MACHINE HEAD PARTS LIST COVERING FIGURE “A” (cont’d) ITEM NO. ORDER BY PART NUMBER QTY. 39 40 41 42 43 44 45 46 47 48 52 53 54 55 56 57 58 42 43 44 -59 60 61A 61 61B 61C 61D 62 63 65 67 67A 67B 68 69 70 71 71A 71B 71C 72 72A 73 74 74A 75 76 77 MBB-2529A MBB-1807A MBB-365A MBB-646 MBB-647 MBB-359A LBN-385A LBN-386 KN-172 MB-3089A MBB-3491A MBB-2498A PBR-147A MBB-2497A PHS-582 MBB-3495A MBH-649A MBB-646 MBB-647 MBB-359A MBC-345A MBC-346A MBB-642A MBB-332A MBC-353A PHS-165A MBC-354A PHS-164A MBC-347A AG-128A PNP-329A MBB-2320 MAN-1223 KN-416 MBB-2563A MAN-612 PNP-328A PHM-306A PHW-119 KN-567 PHS-775 KKN-943A PHM-728A MBB-2528A PHS-506 LBA-451 LBN-462A LN-570A MBC-356A 1 1 1 1 1 1 2 4 4 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 4 1 4 1 1 2 1 1 4 4 1 1 1 1 1 1 1 1 1 1 4 4 1 1 1 N/S indicates Not Shown Page 4 DESCRIPTION ....Spacer ....Spindle Pulley ....Thrust Assembly with ......Screw (3/8-16 x 3/4 Soc. Hd. Cap) ......Washer (3/8) ......Washer (.555 Special) ....Feed Arm Assembly (Pkg. of 2) with ......Screw (5/16-18 x 1/2 Hex Hd. Cap) ......Nut (5/16-18 Hex) ....Feed Arm Stabilizer with Attaching Hardware ....Bearing Spacer ....Bearing Sleeve ....Bearing with Snap Ring ....Bearing Retainer with ......Screw (1/4-20 x 3/4 Soc. Hd. Cap) ....Spindle ....Feed Rod Assembly with ......Screw (3/8-16 x 3/4 Soc. Hd. Cap) ......Washer (3/8 Special) ......Washer (.555 Special) ....Adjustable Spindle Nose Complete includes ......Spindle Nose Shell ......Drive Plate with ........Set Screw (1/4-20 x 3/8 Soc. Full Dog Pt.) ......Set Screw (5/16-24 x 5/8 Soc. Flat Pt.) (Pkg. of 4) ......Set Screw (1/2-20 x 1/2 Soc. Flat Pt.) ......Set Screw (5/16-40 x .480 Soc. Ground Flat Pt.) (Pkg. of 4) ......Set Screw (1/4-20 x 1/2 Soc. Full Dog Pt. / Nylok) ......Adjustable Nose ......Screw (1/4-20 x 3/4 Soc. Hd. Cap) (Pkg. of 2) ....Heavy Pressure Dial Overlay ....Housing ....Washer (3/8 Plain) ....Screw (3/8-16 x 1-1/4 Hex Hd. Cap) ....Dial Pointer with ......Screw (1/4-20 x 3/8 Hex Hd. Cap) ....Feed Dial Overlay ....Belt Cover Latch Pin with ......Washer (5/16 Lock) ......Screw (5/16-18 x 3/4 Hex Hd. Cap) ......Screw (5/16-18 Lock) ....Top Cover ....Grommet ....Cover with ......Screw (10-32 x 1/4 Button Hd. Cap) ......Washer ....Mandrel Wrench ....Concentric Sleeve - Optional (Not Supplied with Machine) ....Spindle Nose Cover SECTION I HONING MACHINE HEAD S E E F IG . N FIGURE B - HONING MACHINE HEAD ASSEMBLY PARTS LIST COVERING FIGURE “B” ITEM NO. ORDER BY PART NUMBER QTY. 1 2 3 4 5 6 7 8 9 MBB-2485A EL-11 LBA-437 LBN-450C LBN-369 LBA-150 LBA-445A MB-908 LBA-456A 1 1 1 1 1 2 1 1 1 N/S indicates Not Shown DESCRIPTION ....Pressure Dial Assembly, Upper with ......Spring ......Plate ......Set Collar with ........Set Screw (1/4-20 x 1/4 Soc. Cup Pt.) ......Nut (3/8-24 Hex) ......Spherical Socket with ........Spherical Washer ......Thread Nut with (Parts continued on next page) Page 5 SECTION I HONING MACHINE HEAD PARTS LIST COVERING FIGURE “B” (cont’d) ITEM NO. ORDER BY PART NUMBER QTY. 9A 10 11 12 2 3 4 5 6 13 14 7 8 9 9A 10 11 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 PHN-147 LBA-438C MSA-63 MBB-2475A EL-11 LBA-437 LBN-450C LBN-369 LBA-150 MSA-151 LBA-453A LBA-445A MB-908 LBA-456A PHN-147 LBA-438C MSA-63 MBB-2525A MBB-938 MSN-345 MBB-946A MBB-939 MBB-947C MBB-2487A PHW-118 LBN-431 MBB-885A PBR-54A PBR-34A MBB-2920A MBB-866A PHS-106 MBB-858 MBB-859 MBB-867A MBB-1897A MBB-312 LBA-381A LBA-367C PBR-53A MBB-1859A MBB-1858A LBN-337A KN-456 MBB-2912A LBN-485 PSP-303A LBA-446A MBB-2915A PHS-612 PHW-145A MBB-2464A MBB-2460A CK-3187 LBN-408 LBA-395A LBN-406A 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 3 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 N/S indicates Not Shown Page 6 DESCRIPTION ........Jam Nut (3/8-24 Hex) ......Pin with ........Nut (10-32 Hex) ....Pressure Dial Assembly, Lower with ......Spring ......Plate ......Set Collar with ........Set Screw (1/4-20 x 1/4 Soc. Cup Pt.) ......Nut (3/8-24 Hex) ......Washer (3/8 Hardened) ......Spring ......Spherical Socket with ........Spherical Washer ......Thread Nut with ........Jam Nut (3/8-24 Hex) ......Pin with ........Nut (10-32 Hex) ....Pressure Rod Assembly with ......Spring Collar ......Set Screw (5/16-18 x 5/16 Soc. Cup Pt.) ......Spring with ........Washer (Special) ....Lever with ......Lever Pivot with ........Washer (1/4 Lock) ........Nut (1/4-20 Hex) ....Spring Support Assembly ....Bearing ....Bearing (Pkg. of 2) ....Arm & Shaft Assembly with ......Set Collar with ........Set Screw (1/4-28 x 5/16 Soc. Cup Pt.) ........Washer (Special) ........Sping Washer ........Thrust Bearing, Nylon (Pkg. of 3) ......Spacer ......Set Screw (3/8-16 x 1/2 Soc. Cup Pt.) ....Adjusting Nut Assembly ....Sleeve ....Bearing (Pkg. of 2) ....Idler Shaft ....Thrust Bearing (Pkg. of 1) ....Set Collar with ......Set Screw (1/4-20 x 3/8 Soc. Cup Pt.) ....Idler Tension Arm with ......Set Screw (3/8-16 x 5/8 Soc. Cup Pt.) ....Spring ....Lever ....Crank Arm Lever with ......Screw (1/4-28 x 3/4 Soc. Flat Hd. Cap) ......Washer (Spring) ....Bearing Insert ....Stub Crank Arm Assembly with ......Washer (1/4 Plain) ......Cotter Pin (1/16 x 1/2 Long) ....Feed Arm Link Assembly ....Stop Pin with (Parts continued on next page) SECTION I HONING MACHINE HEAD PARTS LIST COVERING FIGURE “B” (cont’d) ITEM NO. 55 56 57 59 60 58 61 58 62 63 64 65 66 67 68 69 70 71 72 73 74 68 75 76 77 78 79 80 81 82 83 84 85 86 87 88 90 91 92 93 94 95 96 97 97A 99 100 N/S 101 98 102 103 104 105 106 107 108 ORDER BY PART NUMBER QTY. KN-568 LBN-408 MBB-2405A MBB-986A LBN-369 LBN-379 PSP-105A LBN-379 LBN-372A LBN-369 MBB-719A MBB-2895A MBB-718A MBB-716 PG-587 PHS-122 PHS-583 KKN-1116A PHS-579 KKN-1110A PHR-326 PG-587 PHW-132 KKN-1114A PG-505 PG-984 KKN-1120A PHS-120 KKN-1139A MSN-277 MBB-707A MBB-708TA MBB-709TA MBB-705A MBB-2320 --MSN-189 PHS-584 KKN-1165A KKN-1169 PHW-119 LBB-891 KKN-1171 LBS-451 AG-178 KKN-1155A KKN-1161 POR-107A KKN-1163A PHS-532 ASC-377A ASC-378 PHS-532 ASC-358A --PHS-582A PHW-118 1 1 1 1 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 2 1 1 2 2 1 2 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 2 1 1 1 1 1 2 2 DESCRIPTION ......Washer (5/16 Plain) ......Nut (5/16-18 Hex) ....Feed Screw with ......Set Collar with ........Set Screw (1/4-20 x 1/4 Soc. Cup Pt.) ......Fiber Washer ....Spring with ......Fiber Washer ....Dial Assembly with ......Set Screw (1/4-20 x 1/4 Soc. Cup Pt.) ....Plate ....Body Assembly with ......Spring (Pkg. of 3) ......Rocker ......Washer ......Set Screw (1/4-20 x 1/2 Soc. Flat Pt.) ......Screw (1/4-20 x 1 Soc. Hd. Cap) ....Follower Spring Stop with ......Screw (10-32 x 1-1/4 Soc. Hd. Cap) ....Follower Block Assembly with ......Retaining Ring ......Washer ......Spring Washer ......Follower Spring Set (2 Pieces) with ........Washer ........Screw (4-40 x 5/16 Self Tapping Binding Hd.) ....Trigger Assembly with ......Set Screw (8-32 x 1/2 Soc. Oval Pt.) ....Spindle Nose Cover Clip with ......Screw (10-32 x 3/8 Rd. Hd.) ....Dial Indicator & Pin Assembly includes ....Dial Indicator Bezel & Crystal ......Dial Indicator Face ......Cushion Indicator Tip ....Housing ....Automatic Shutoff (See Fig. “C”) ......Washer (1/4 Plain) ......Screw (1/4-20 x 1-1/2 Soc. Hd. Cap) ....Base Assembly with ......Spacer Washer ......Washer (5/16 Lock) ......Screw (5/16-18 x 3/4 Soc. Hd. Cap) ......Cover ......Washer ......Screw (10-32 x 3/8 Soc. Hd. Cap) ....Piston Assembly with ......Cylinder ......“O” Ring ....Pivot Cross Pin with ......Screw (10-32 x 1/4 Button Hd. Cap) ....Cable Pull with ......Bushing ......Screw (10-32 x 1/4 Button Hd. Cap) ....Cable Kit ....Stone Saver Assembly (See Fig. “D”) ....Screw (1/4-20 x 3/4 Soc. Hd. Cap) (Pkg. of 2) with ......Washer (1/4 Lock) N/S indicates Not Shown Page 7 SECTION I HONING MACHINE HEAD FIGURE C - AUTOMATIC SHUTOFF Page 8 SECTION I HONING MACHINE HEAD PARTS LIST COVERING FIGURE “C” ITEM NO. ORDER BY PART NUMBER QTY. 1 2 3 4 5 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 28 25 29 30 31 32 33 34 -35 35A 36 37 -38 39 40 41 42 -43 44 45 46 47 48 KKN-964A PHS-506 PHS-580 PNP-333A PHS-584 MSN-189 KKN-2041A KKN-1079A PHS-751 PHS-579 PG-587 KKN-1069A KKN-1068A KKN-1062A PHR-307 KKN-1078A KKN-1061A KKN-1064A KKN-1019A LBN-309 LN-1656 KKN-1021A PHS-506 PSP-304A PHS-594A KKN-1024A KKN-1015A PHS-611 KKN-1022A PHS-626 KKN-1050A KKN-1030A PSP-312A PHS-603 KKN-1059A KKN-1055A KKN-1056 LN-78 KKN-1057A MSA-63 KKN-1025A KKN-1040A KKN-1035A KKN-1045A PG-587 PG-2252 PSP-301A KKN-1080A 1 3 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 DESCRIPTION ....Cover with ......Screw (10-32 x 3/8 Button Hd. Cap) ......Screw (1/4-28 x 3/8 Button Hd. Cap) ......Instruction Label ....Screw (1/4-20 x 1-1/2 Soc. Hd. Cap) ....Washer (1/4 Plain) ....Manual Trip Lever with ......Lock Out Spring with ........Screw (4-40 x 1/4 Self Tapping Binding Hd.) ......Screw (10-32 x 1-1/4 Soc Hd. Cap) ......Washer ......Manual Trip Pivot ....Retaining Plate ....Switch Box Spacer with ......Retaining Ring ....Spring ....Guide Rail ....Spacer ....Lower Mount with ......Set Screw (1/4-20 x 1/2 Soc. Cup Pt.) ......Screw (10-32 x 5/8 Soc. Flat Hd. Cap) ....Front Bar with ......Screw (10-32 x 3/8 Button Hd. Cap) ....Spring ....Shoulder Screw (5/16 x 1/4 with 1/4-20 x 7/16 Thd.) ....Lockout Screw ....Base ....Screw (1/4-20 x 5/8 But. Hd. Cap) ....Main Bearing Shaft with ......Screw (1/4-28 x 11/16 Flat Hd. Soc. Cap) ....Toggle Set includes ......Toggle Link Assembly, Lower with ........Spring ......Screw (10-32 x 3/4 Button Hd. Cap) ......Inner Race ......Toggle Link Assembly, Outer includes ........Toggle Link, Outer ........Groove Pin ........Cam Screw ........Nut (10-32 Hex) ......Toggle Link Assembly, Inner ....Auto Trip Assembly includes ......Auto Trip Lever Assembly ......Trip Catch Assembly ......Washer ......Retaining Ring ......Spring ....Cocking Lever N/S indicates Not Shown Page 9 SECTION I HONING MACHINE HEAD FIGURE D - STONE SAVER ASSEMBLY PARTS LIST COVERING FIGURE “D” ITEM NO. 1 3 4 5 6 5 7 8 9 10 11 12 13 14 15 16 17 ORDER BY PART NUMBER KKN-860A KKN-895A PHP-567 PHS-612 KKN-924A PHS-612 PEM-336A LBA-451 PHS-552 KKN-889A PHS-683 LBA-451 KKN-893A PHW-163 PHR-308 KKN-894A PHS-578 N/S indicates Not Shown Page 10 QTY. 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 2 DESCRIPTION ....Sub Base Assembly with Threaded Inserts ....Piston Pivot with ......Groov-Pin ......Screw (1/4-28 x 3/4 Soc. Flat Hd. Cap) ....Spring Anchor with ......Screw (1/4-28 x 3/4 Soc. Flat Hd. Cap) ....Clamp with ......Washer (#10 Shakeproof) ......Screw (10-32 x 1/2 Rd. Hd.) ....Adjusting Screw Block with ......Screw (10-32 x 5/8 Button Hd. Cap) ......Washer (#10 Shakeproof) ....Adjusting Screw with ......Washer (1/4 Spring) ......Retaining Ring ....Retaining Cap with ......Screw (6-32 x 3/8 Soc. Hd. Cap) (Parts continued on next page) SECTION I HONING MACHINE HEAD PARTS LIST COVERING FIGURE “D” (cont’d) ITEM NO. 18 19 20 21 22 19 20 21 23 24 25 26 27 28 29 30 31 33 34 36 37 38 39 40 41 42 43 44 45 46 48 47 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 ORDER BY PART NUMBER KKN-887A PG-587 LBA-451 PHS-506 KKN-886A PG-587 LBA-451 PHS-506 KKN-872A PHR-307 TN-54 KKN-871A KKN-883A AG-438D KKN-882A PHS-713 KKN-875A PHR-307A KKN-915A CRG-939A KKN-912A PSP-307A KKN-905A KKN-909A PHR-305A KKN-927A PHW-171 MBB-982 KKN-929A KKN-930A LN-1545 KKN-908A KKN-949A LN-1545 KKN-944A PG-587A PHN-134A KKN-918A MSN-177C KKN-920A PHR-302 KKN-935A PHM-727A PHN-117 KKN-952A PHS-506 LBA-451 PNP-332A KKN-953A QTY. 1 2 2 2 1 2 2 2 1 1 1 1 1 16 1 2 1 1 1 1 1 1 1 1 1 1 4 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 1 1 DESCRIPTION ....Top Clamp with ......Washer (#10 Plain) .....Washer (#10 Shakeproof) ......Screw (10-32 x 3/8 Button Hd. Cap) ....Bottom Clamp with ......Washer (#10 Plain) ......Washer (#10 Shakeproof) ......Screw (10-32 x 3/8 Button Hd. Cap) ....Cam with ......Retaining Ring ......Spring Washer ....Cross Slide ....Ball Carrier with ......Gage Ball (Pkg. of 16) ....End Plate with ......Screw (5-40 x 3/16 Soc. Hd. Cap) ....Fork & Rod with ......Retaining Ring ......Cylinder & Pin with ......“O” Ring ....Cylinder ....Spring ....Piston ....Piston Nut ....Retaining Ring ....Metering Screw ....Washer (1/4 Spring) ....Washer (1/4 Plain) ....Metering Stop ....Stop Collar & Pin with ......Set Screw (8-32 x 1/4 Soc. Cup Pt.) ....Spring Clip ....Metering Knob with ......Set Screw (8-32 x 1/4 Soc. Cup Pt.) ....Pointer with ......Washer (#10 Plain) ......Nut & Lockwasher ....Cam Lever with ......Screw (10-32 x 5/8 Soc. Hd. Cap) ....Pull Rod Pivot with ......Retaining Ring ....Pull Rod ....Stud Bumper with ......Nut & Lockwasher ....Cover with .....Screw (10-32 x 3/8 Button Hd. Cap) ......Washer (#10 Shakeproof) ......Stonesaver Overlay ......Hole Plug N/S indicates Not Shown Page 11 SECTION II - HONING MACHINE BASE FIGURE E - BASE, FILTER, PUMP, & COOLANT ASSEMBLY Page 12 SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “E” ITEM NO. 1 1 1 2 3 4 2A 3 3A 4 2B 5 N/S N/S 6 6A 6B 6C 6D 6E N/S N/S N/S 7 7A 7B 7C 7D 7E 7F 7J 8 9 10 11 11A 12 13 14 15 16 16A N/S N/S 17 18 19 N/S 21 N/S ORDER BY PART NUMBER PMO-345A PMO-347A PMO-345H PF-224A PHW-119 KN-172 PF-224D --PHW-119 KN-172 CH-371A MB-3297A KN-568 KN-172 PF-500A PF-501 PHS-164A PF-502A PHW-119 LBN-386 PF-505A PF-506A PF-507A PPP-147A PPP-161A PPP-171A PF-171A PPP-29A PPP-22A PPP-116A PPP-169A PPP-41A PPP-207A PPP-42A PF-317A PEM-315 PF-162C MAN-1028 PHW-118 LBN-431 PF-240A PF-243A PF-244A PF-247A PF-246A PF-260A PF-270A PF-105-4 PF-257A PF-258A N/S indicates Not Shown QTY. 1 1 1 1 8 8 1 1 1 2 1 1 4 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 DESCRIPTION ....Motor (1/2 H.P., 208/230/460 Volt, 60 Hz, 3 Ph.) ....Motor (1/2 H.P., 380/400 Volt, 50 Hz, 3 Ph.) ....Motor (1/2 H.P., 220/440 Volt, 50 Hz, 3 Ph.) ....Flex Bolt Mounting Set with ......Washer (5/16 Plain) Nut (5/16-18 Hex) ....Flex Bolt Mounting with ......Washer (5/16 Plain) ......Washer (5/16 Lock) ......Nut (5/16-18 Hex) ....Pump Bracket ....Motor Base with ......Washer (5/16 Plain) ......Nut (5/16-18 Hex) ....Pump with ......Collar ......Set Screw (1/4-20 x 1/2 Full Dog Point with insert) ....Bracket with ......Washer (5/16 Lock) ......Screw (5/16-18 x 1/2 Hex Hd. Cap) ....Mechanical Seal (PF-500A Pump) ....Bearing (PF-500A Pump) ....Gasket Set (PF-500A Pump) ....Close Nipple ....Adapter ....Side Outlet Elbow ....Relief Valve ....Hose Assembly ....Hose Assembly ....Adapter ....Street Elbow ....Hose Assembly ....Tee ....Hose ....Intake Strainer with ......Clamp ....Mounting Bracket with ......Screw (1/4-20 x 3/4 Hex Hd. Cap) ......Washer (1/4 Lock) ......Nut (1/4-20 Hex) ....Filter Container Assembly with ......Cover ......Gasket ......Spring ......Air Vent ......Clamp Assembly with ........Tee Handle Assembly ....Filter Element (Pkg. of 4) ....Standpipe with ......Washer (Fiber) (Pkg. of 2) (Parts continued on next page) Page 13 SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “E” (cont’d) ITEM NO. 22 23 24 25 26 27 28 29 30 31 32 33 33A 34 35 36 37 37A 38 39 N/S 40 41 42 43 44 45 N/S 46 47 48 49 50 51 52 53 54 55 60 61 62 63 65 64 65 66 67 68 69 70 ORDER BY PART NUMBER QTY. PF-259A PPP-351 MB-2267A CRG-404 MB-2165A PHS-599 MB-2177A MB-2184A MB-2176A MB-2182A MBB-1630A PPP-41A PPP-27A PEM-340 PPP-148A PPP-533 PES-338A PES-338-1A MB-2185A MB-2194A PHN-116 MB-2193A MB-2202A MB-2203A MB-2205A KN-538 MB-2210A PHP-101 P-144 LBA-451 MSA-63 PF-288A PHSM-629 PHW-327 LBA-451 MB-2214A MB-2299A CRG-404 MB-2143A MB-2135A MB-2140A MAN-1028 PHW-118 MB-2132A PHW-118 MSA-219 KKN-1124A MBB-977 PHN-121 MB-3095A 1 1 1 2 1 1 1 1 3 3 1 1 1 3 1 1 1 1 3 3 3 3 1 1 1 1 1 4 2 6 6 1 2 1 1 1 2 2 1 1 2 4 4 1 2 2 1 1 1 1 N/S indicates Not Shown Page 14 DESCRIPTION ....Draincock ....Close Nipple (1/2 NPT Black Iron) ....Rear Splash Guard - Left with ......Screw (1/4-20 x 3/8 Rd.Hd.) ....Valve Body Assembly with ......Screw (1/4-20 x 2 Soc. Hd. Cap) ......Inlet Stem with ........“O” Ring ......Outlet Stem (Pkg. of 1) with ........“O” Ring (Pkg . of 3) ....Check Valve ....Hose Assembly ....Hose Assembly ....Clamp ....Tee (1/2 x 1/2 x 1/2) ....Relief Valve ....Solenoid Valve ....Solenoid ....Jet Assembly (Pkg. of 1) with ......Jet Clamp (Pkg. of 1) ......Wing Nut ....Flexible Tube Feeder with Clamp (Pkg. of 1) ....Support Rod Clamp ....Support Rod Clamp ....Wing Hand Screw Assembly with ......Washer (1/2 Plain) ....Door & Hinge with ......Screw (10-32 x 1/2 Flat Hd.) ......Screw (10-32 x 1/2 Soc. Hd. Cap) ......Washer (#10 Shakeproof) ......Nut (10-32 Hex) ....Handle with ......Screw (8-32 x 1/4 Rd. Hd.) ......Washer (3/8 Shakeproof) ......Nut (3/8-24 Hex. Jam) ......Cam ....Reservoir Retainer (Pkg. of 1) with ......Screw (1/4-20 x 3/8 Rd. Hd.) ....Clutch Return Spring ....Clutch Tube ....Bearing & Bracket Assembly (Pkg. of 1) with ......Screw (1/4-20 x 3/4 Hex Hd. Cap) ......Washer (1/4 Lock) ....Pedal Stop with ......Washer (1/4 Lock) ......Screw (1/4-20 x 3/4 Hex Hd. Cap) ....Clutch Nut with ......Shoulder Screw (5/16 x 5/8 with 1/4-20 x 7/16 Thd.) ......Nut (1/4-20 Hex Lock) ....Top Plate with (Parts continued on next page) SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “E” (cont’d) ITEM NO. ORDER BY PART NUMBER QTY. 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 92 104 105 105A 106 107 108 109 110 111 PHS-567 LBN-452 MAN-1223 KN-383 PHS-644 KN-568 PHW-119 KN-172 KKN-1149A CRG-404 MB-2148C KKN-1132A KKN-1131A MSN-189 PHS-619 KKN-1125C KKN-348A PHS-614 PHN-122 KKN-1123A MB-3075 MBB-3132A LBN-401 PHW-118 MAN-1028 MBB-3138A LN-1676 PES-155A PHS-695 PHN-117 2 2 2 2 2 4 2 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 DESCRIPTION ......Screw (3/8-16 x 1-1/2 Flat Hd. Soc. Cap) ......Washer (3/8 Plain) ......Washer (3/8 Lock) ......Nut (3/8-16 Hex) ......Screw (5/16-18 x 1 Hex Hd. Cap) ......Washer (5/16 Plain) ......Washer (5/16 Lock) ......Nut (5/16-18 Hex) ....Rear Splash Guard - Right with ......Screw (1/4-20 x 3/8 Rd. Hd.) ....Pivot Block with ......Lower Bearing Nut ......Sleeve with ........Washer ........Screw (1/4-20 x 1-3/4 Soc. Hd. Cap) ....Pull Rod & Collar with ......Cam Rod Bushing ......Screw (10-32 x 1/2 Button Hd. Cap) ......Nut (5/16-24 Hex Jam) ......Bumper ....Base Shell ....Switch Plate with ......Washer (1/4 Plain) ......Washer (1/4 Lock) ......Screw (1/4-20 x 3/4 Hex Hd. Cap) ......Pivot Bushing with ........Screw (1/4-20 x 7/8 Flat Hd. Soc.Cap) ....Switch with ......Screw (6-32 x 1-1/2 Flat Hd.) ......Nut (6-32 Hex) N/S indicates Not Shown Page 15 SECTION II HONING MACHINE BASE FIGURE F - AIR ACTUATED PEDAL DEPRESSOR Page 16 SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “F” ITEM NO. ORDER BY PART NUMBER QTY. 1 2 3 4 5 -6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 MBC-506A PPP-242A PPP-294A 78156A PPP-40A MBC-507C ----PHS-1062 ----MBC-537C PHS-582 PHW-118 LBN-431 MBC-528A PG-719 PES-330A PHW-156 PHS-735 PPP-297A 78156A 78156A MBC-529A KN-46 PG-762 PPP-439A PPP-323A PPP-316A 78156A MBC-614 PPP-127A PPPM-402A PFC-116A PHN-103 MBC-544A MBC-524A PHS-170 KKN-26 LBN-431 MBC-547A MBC-546A PHW-174 P-165 PHS-657 MBC-298A PHW-119 KN-172 LBN-408 PHW-118 1 1 1 * 1 1 1 4 4 1 2 1 4 4 4 1 2 1 2 2 2 * * 1 2 2 1 2 1 * 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 4 N/S indicates Not Shown DESCRIPTION ....Cylinder ....Reducer Bushing ....Swivel Elbow ....Tubing (5/32 O.D. Natural) ....Sintered Breather ....Mounting Kit includes ......Bracket ......Washer ......Screw ......Clevis Pin ......Hair Pin ....Eye Bracket with ......Screw (1/4-20 x 3/4 Hex. Soc. Hd. Cap) ......Washer (1/4 Lock) ......Nut ....Valve Bracket with ......Screw (1/4-20 x 1/2 Flat Hd. Soc. Cap) ....Directional Valve with ......Washer (#8 Shakeproof) ......Screw (8-32 x 7/8 Hex Soc. Button Hd. Cap) ....Connector (Pkg. of 1) ....Tubing (5/32 O.D. Natural) ....Tubing (5/32 O.D. Natural) ....Air Valve with ......Washer (#10 Lock) ......Screw (10-32 x 1-1/8 Hex. Hd. Cap) ....Swivel Elbow ....Low Profile Breather (Pkg. of 2) ....Male Swivel Branch Tee ....Tubing (5/32 O.D. Natural) ....Solenoid Cable Assembly ....Pipe Plug ....Adapter ....Flow Control Valve ....Nut (1/2-20 Hex. Jam) ....Spring ....Rod End with ......Set Screw (1/4-20 x 1/4 Hex. Soc. Cone Pt.) ......Set Screw (1/4-20 x 5/8 Hex. Soc. Flat Pt.) ....Nut (1/4-20 Hex) ....Bushing ....Sleeve ....Washer (1-1/8 Plain) ....Washer (9/16 Plain) ....Screw (5/16-18 x 2-1/4 Hex. Soc. Hd. Cap) ....Clamp ....Washer (5/16 Lock) ....Nut (5/16-18 Hex) ....Nut (5/16-18 Hex. Jam) ....Washer (1/4 Lock) *Material sold by the foot only. (Parts continued on next page) Page 17 SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “F” (cont’d) ITEM NO. ORDER BY PART NUMBER QTY. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 PHS-762 MBC-297A ASC-776A PHSM-523 LBA-451 PHNM-402 PPP-439A PPP-440A PPPM-406A 78161A PEM-320A MBC-515A MBC-532A PHW-119 LBN-408 PPP-190A HS-226A MBC-531A MBC-531-1A --PPP-242A 78161A PPPM-406A PPP-479A 4 1 2 2 2 2 2 1 1 * 2 1 1 1 1 1 1 1 1 1 1 * 1 1 N/S indicates Not Shown Page 18 DESCRIPTION ....Screw (1/4-20 x 1-3/4 Hex. Hd. Cap) ....Upper Clamp ....Air Valve (Pkg. of 1) with ......Screw (M4 x .07 x 55mm Slot Hd. Machine) ......Washer (#6 Lock) ......Nut (M4 x .07 Hex) ....Male Elbow (Pkg. of 1) ....Straight Fitting ....Male Run Tee ....Tubing (5/32 O.D. Orange) ....Solenoid Connector (Pkg. of 1) ....Filter Regulator Assembly includes ......Stud ......Washer (5/16 Lock) ......Nut (5/16-18 Hex. Jam) ......Hose Barb ......Tubing (3/8 O.D.) ......Filter Regulator ......Gauge ....Air Hose (Supplied By Customer) ....Reducing Bushing (1/4 Male to 1/8 Female) ....Tubing (5/32 O.D. Orange) ....Male Swivel Run Tee ....Union “Y” Fitting (For “CE” Machines) *Material sold by the foot only. SECTION II HONING MACHINE BASE FIGURE G - COOLANT RESERVOIR UNIT PARTS LIST COVERING FIGURE “G” ITEM NO. 1 2 3 4 5 6 7 8 ORDER BY PART NUMBER MB-3275A MB-2281A MB-3262A PF-397A PHS-693 MSN-189 PHW-118 LBN-431 QTY. 1 1 1 1 1 1 1 1 DESCRIPTION ....Oil Reservoir with ......Pipe Plug (3/8 NPT) ....Settlement Tray ....Hose Bracket with ......Screw (1/4-20 x 5/8 Hex. Hd. Cap) ......Washer (1/4 Plain) ......Washer (1/4 Lock) ......Nut (1/4-20 Hex.) N/S indicates Not Shown Page 19 SECTION II HONING MACHINE BASE FIGURE H - FOOT PEDAL UNIT Page 20 SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “H” ITEM NO. 1 2 3 4 N/S 5 6 7 8 9 10 11 12 13 14 11 12 13 -15 16 17 18 -19 20 21 22 23 24 25 ORDER BY PART NUMBER PHS-594A PHN-121 MB-2123A LBN-450C LBN-369 PSP-308 MB-908 MB-907 MB-2295A KKN-37 MB-3110A MB-2117A MAN-1223 MAN-922 MB-3115A MB-2117 MAN-1223 MAN-922 --MB-2122A MB-2118 MBB-971 LBN-452 --MBC-710 MBC-720A PHP-415 MB-2118 MBB-971 MBC-725 MBC-728 QTY. 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 1 1 1 1 DESCRIPTION ....Shoulder Screw (5/16 x 1/4 with 1/4-20 x 7/16 Thd.)(Pkg. of 1) with ......Nut (1/4-20 Hex) ....Pedal Link Assembly (Pkg. of 1) with ......Set Collar (Pkg. of 1) with ........Set Screw (1/4-20 x 1/4 Soc. Cup Point) ......Spring ......Spherical Washer ......Nut (3/8-16 Hex. Self Locking) ....Tread Assembly with ......Screw (5/16-18 x 1/2 Soc. Hd. Cap) ....Foot Pedal Assembly - Right with ......Pedal Bushing ......Washer (3/8 Lock) ......Screw (3/8-16 x 3/4 Hex. Hd. Cap) ....Foot Pedal Assembly - Left with ......Pedal Bushing ......Washer (3/8 Lock) ......Screw (3/8-16 x 3/4 Hex. Hd. Cap) FOLLOWING PARTS ARE FOR NON “CE” MACHINES ....“U” Bar ....Clamp Nut ....Screw (5/16-18 x 1 Soc. Hd. Cap) ....Washer (3/8 Plain) FOLLOWING PARTS ARE FOR “CE” MACHINES ....Pedal Assembly ....Pedal Extension Assembly ....Spring Pin ....Clamp Block ....Screw (5/16-18 x 1 Soc. Hd. Cap) ....Pedal Cover Assembly ....Pedal Yoke N/S indicates Not Shown Page 21 SECTION II HONING MACHINE BASE FIGURE I - DRIP TRAY & ACCESSORIES Page 22 SECTION II HONING MACHINE BASE PARTS LIST COVERING FIGURE “I” ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 22 23 24 26 27 28 29 -30 31 23 24 -30 N/S 32 33 34 35 36 37 ORDER BY PART NUMBER MB-2230A PHN-124 MBB-856A MB-2220A MB-2224 KN-99 KN-422 MAN-1079A MB-2228A MB-2405A MB-2418A MB-2235A MB-2248A MB-2253 MB-2254 KN-972 MB-2208A MB-2207 KN-568 PHN-116 MB-2249A MB-2251 CRG-868 PHS-601 MB-2258A MB-2251 CRG-868 PHS-601 MB-2256A MB-2257 PG-724 MAN-700 --MB-2328C MB-2252A CRG-868 PHS-601 --MBC-706A MB-2328C MBC-730 GGN-109A MBC-736 MBC-702A PHR-335 PHS-1014 QTY. 2 4 1 1 2 2 2 1 1 1 1 1 2 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 2 2 2 2 2 DESCRIPTION ....Stationary Spalsh Guard (Pkg. of 1) with ......Nut (1/4-20 Hex. Acorn) ....Neoprene Bumper ....Stationary Drip Tray with ......Reinforcing Block ......Washer (3/8 Plain) ......Screw (3/8-16 x 1 Hex. Hd. Cap) ....Elbow ....Pipe Extension ....Work Tray ....Tray Pad ....Movable Tray Assembly with ......Guide Rod (Pkg. of 2) ......Detent Rail - Right ......Detent Rail - Left ......Screw (10-24 x 3/8 Flat Hd. I.M.S.) ....Rear Support Rod with ......Rear Support Clamp ......Washer (5/16 Plain) ......Wing Nut (5/16-24) ....Movable Splash Guard with ......Spacer ......Washer (3/16 Plain) ......Screw (10-24 x 5/8 Button Hd. Cap) ....Movable Splash Guard with ......Spacer ......Washer (3/16 Plain) ......Screw (10-24 x 5/8 Button Hd. Cap) ....Accessory Holder with ......Spacer ......Screw (10-32 x 3/4 Flat Hd. Soc. Cap) ....Diamond Dresser FOLLOWING PARTS ARE FOR NON “CE” MACHINES ....Anti-Splash Pads (Upper and Lower) ....Front Splash Guard ....Washer ....Screw (10-24 x 5/8 Button Hd. Cap) FOLLOWING PARTS ARE FOR “CE” MACHINES ....Anti-Splash Pad (Upper) ....Anti-Splash Pad (Lower) (Pkg. of 2) ....Splash Gate ....Washer (Nylon) (Pkg. of 1) ....Spring Post ....Torsion Spring (Pkg. of 1) ....Retaining Ring ....Screw (10-32 x 1-3/4 Soc. Hd. Cap) N/S indicates Not Shown Page 23 SECTION III - POWER STROKER C FIGURE J - POWER STROKING ATTACHMENT Page 24 SECTION III POWER STROKER PARTS LIST COVERING FIGURE “J” ITEM NO. 1 1 1 1A 1A 1A 1B 1B 1B 2 3 4 5 8 N/S 8A N/S 25 23 31 32 10 33 34 35 36 37 38 39 10 41 43 44 45 46 47 47A 47B 47C 48 49 50 51 52 N/S 53 54 54A 55 56 ORDER BY PART NUMBER QTY. PMO-381A PMO-382A PMO-383A MBC-381A MBC-382A MBC-383A CV-241A CV-243A CV-246A KN-567 KN-568 PHW-119 KN-172 KKN-338A LBN-340 KKN-438A LBN-340 KKN-454A PHS-506 KKN-168A KKN-167 PHS-506 KKN-1855A KKN-1858A MAN-1223 PHS-605 KKN-1975A --PHW-182 PHS-506 KKN-1976A KKN-1878 KKN-374A KKN-371A KKN-372A KKN-378A PHW-127 MSN-189 PG-36 --PHS-589A KN-538 PHS-572A LBN-401 PHW-118 KKN-1870A PHS-627 KKN-334 KKN-340A PHS-613 1 1 1 1 1 1 1 1 1 4 4 4 4 1 1 1 1 1 1 1 1 6 1 1 1 1 1 2 3 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 N/S indicates Not Shown DESCRIPTION ....*Motor w/Brake (1/2HP, 208/230/460V, 60Hz, 3Ph, 1725 RPM, 5/8 Dia. Shaft) ....*Motor w/Brake (1/2HP, 220/380/400V, 50Hz, 3Ph, 1450 RPM, 5/8 Dia. Shaft) ....*Motor w/Brake (1/2HP, 220/440V, 50Hz,3 Ph, 1425 RPM, 5/8 Dia. Shaft) ....Brake Assembly (208/230/460V, 60Hz) includes Coil Kit ....Brake Assembly (220/380/400V, 50Hz) includes Coil Kit ....Brake Assembly (220/440V, 50Hz) includes Coil Kit ....Coil Kit (208/230/460V, 60Hz) ....Coil Kit (220/380/400V, 50Hz) ....Coil Kit (220/440V, 50Hz) ....Screw (5/16-18 x 3/4 Hex Hd. Cap) ....Washer (5/16 Plain) ....Washer (5/16 Lock) ....Nut (5/16-18 Hex) ....Motor Pulley (60 Hz Machine) with ......Set Screw (1/4-20 x 1/2 Soc. Full Dog Pt.) ....Motor Pulley (50 Hz Machines) with ......Set Screw (1/4-20 x 1/2 Soc. Full Dog Pt.) ....Lower Brace with ......Screw (10-32 x 1/4 Button Hd. Cap) ....Shaft Cover with ......Caplug ......Screw (10-32 x 3/8 Button Hd. Cap) ....Frame Assembly ....Pivot Stud with ......Washer (3/8 Lock) ......Screw (3/8-16 x 1 Soc. Hd. Cap) ....Pivot Assembly with ......Bearing (Not Recommended to be sold separately) ......Thrust Washer ......Screw (10-32 x 3/8 Button Hd. Cap) ......Wedge with ........Set Screw (Special) ......Spring (Pkg. of 1) ......Lift Pin ......Spring ....Pivot Support with ......Washer (1/4 Lock) ......Washer (1/4 Plain) ......Screw (1/4-28 x 5/8 Hex Hd. Cap) ....Cross Arm Assembly (See Fig. M) ....Screw (1/2-20 x 2-1/2 Soc. Hd. Cap) with ......Washer (1/2 Plain) ....Screw (1/4-20 x 5/8 Nylok Button Hd. Cap) with ......Washer (1/4 Plain) ......Washer (1/4 Lock) ....Drive Head Assembly with ......Screw (5/16-24 x 1 Soc. Hd. Cap) ......Washer ....Lever Assembly with ......Screw (3/8-16 x 1 Flat Hd. Cap) (Parts continued on next page) Page 25 SECTION III POWER STROKER PARTS LIST COVERING FIGURE “J” (cont’d) ITEM NO. ORDER BY PART NUMBER QTY. 57 58 35 59 60 64 65 66 67 70A 71 72 73 73A 74 75 76 77 78 35 79 80 81 91 92 93 6 94 95 96 97 97A 98 99 100 101 102 103 104 105 106 108 109 97A 110 112 113 115 10 116 --PHS-607 MAN-1223 PHS-811 --KKN-364A KKN-363A KKN-362A KKN-366A KKN-384A KKN-361A KKN-367A DL-36 KKN-387A PHS-584A KKN-355A POR-112 KKN-354A KKN-1665A MAN-1223 KN-416 KKN-108A PHS-583 KKN-382A KKN-346A KKN-440A PHN-124 MBB-977 P-165 PHW-120 KKN-348A LBA-451 PHS-614 KKN-383A PHN-106 PHS-640 SN-13 KKN-331A KKN-332A PHS-612 KKN-315A KKN-318A PHS-603 LBA-451 PES-155A PEC-112A --PEM-331A PHS-506 KKN-325A 1 4 4 2 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 2 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 1 1 2 2 1 N/S indicates Not Shown Page 26 DESCRIPTION ....Tube & Shaft Assembly (See Fig. L) ....Screw (3/8-16 x 1-3/4 Hex Hd. Cap) ....Washer (3/8 Lock) ....Screw (3/8-16 x 3/4 Flat Hd.) ....Arm Assembly (See Fig. K) ....End Washer ....Thrust Spacer ....Thrust Disk ....Bearing Retainer with ......Thumb Screw ....Spacer ....Knob with ......Nut (3/8-16 Hex Jam) ......Thumb Screw ....Screw (1/4-20 x 1-1/2 Soc. Hd. Cap) (Pkg. of 4) ....Adjustment Tube with ......“O” Ring (.670 I.D. x 29/32 O.D. x .118) ....Adjustment Rod ....Torque Bar Assembly with ......Washer (3/8 Lock) ......Screw (3/8-16 x 1-1/4 Hex Hd. Cap) ....Guide Cover with ......Screw (1/4-20 x 1 Soc. Hd. Cap) ....Link Rod ....Handle with ......Clutch Knob ......Nut (1/4-20 Hex Acorn) ......Shoulder Screw (5/16 x 5/8 with 1/4-20 x 7/16 Thd.) ......Washer (5/16 Plain) ......Spring Washer (5/16 Shakeproof) ....Cam Rod Bushing with ......Washer (#10 Shakeproof) ......Screw (10-32 x 1/2 Button Hd. Cap) ....Rod End with ......Nut (1/4-28 Hex Jam) ......Screw (1/4-28 x 3/4 Soc. Hd. Cap) ......Spacer ....Cam with ......Bushing ......Screw (1/4-28 x 3/4 Flat Hd. Cap) ....Switch Rod Assembly ....Switch Rod Bearing (Pkg. of 1) with ......Screw (10-32 x 3/4 Button Hd. Cap) ......Washer (#10 Shakeproof) ....Switch (For Non “CE” Machines) with Attaching Hardware ....Cable Connector (For Non “CE” Machines) ....Cable Assembly (For Non “CE” Machines) ....Cable Clamp (For Non “CE” Machines) (Pkg. of 2) with ......Screw (10-32 x 3/8 Button Hd. Cap) ....Motor Base Assembly with (Parts continued on next page) SECTION III POWER STROKER PARTS LIST COVERING FIGURE “J” (cont’d) ITEM NO. 117 6 118 119 120 121 122 123 35 124 N/S 124A N/S N/S N/S N/S N/S N/S ORDER BY PART NUMBER QTY. KKN-447A PHN-124 KKN-343 PHR-308 KKN-444A CRF-1833A KKN-1832 KN-422 MAN-1223 KKN-1834A LBN-340 KKN-1844A LBN-340 KKN-1836A KKN-1837A KKN-1838A KKN-1839A KKN-1840A 1 1 1 2 1 1 1 4 4 1 1 1 1 1 2 1 1 1 DESCRIPTION ......Tension Knob ......Nut (1/4-20 Hex Acorn) ......Motor Pivot ......Retaining Ring ....Belt ....Gear Reducer with ......Key (1/4 Sq. x 1-3/8 Long) ......Screw (3/8-16 x 1 Hex Hd. Cap) ......Washer (3/8 Lock) ....Gear Box Pulley (60 Hz Machine) with ......Set Screw (1/-20 x 1/2 Soc. Full Dog Pt.) ....Gear Box Pulley (50 Hz Machine) with ......Set Screw (1/4-20 x 1/2 Soc. Full Dog Pt.) ....High Speed Oil Seal ....Slow Speed Oil Seal (Pkg. of 2) ....Bearing Set (High Speed Shaft) ....Bearing Set (Low Speed Shaft) ....Gasket Set N/S indicates Not Shown Page 27 SECTION III POWER STROKER FIGURE K - ARM ASSEMBLY Page 28 SECTION III POWER STROKER PARTS LIST COVERING FIGURE “K” ITEM NO. 1 5 5A 5B 6 6A 6B 7 10 10A 11 11B 12 13 14 15 16 17 18 -19 20 21 22 22A 23 N/S 24 22 24A 24B 26 27 22 30 23 25 33 22 35 37 38 36 42 N/S N/S 37 43 44 ORDER BY PART NUMBER QTY. KKN-141D MBC-483A PHS-571A LBN-401 MBC-484A PHW-170 PHS-571 KKN-154A KKN-743A KKN-777A KKN-756A PHS-117 PSP-143A KKN-763A PHS-172 KKN-763 KKN-757A KN-180 AG-128 KKN-720A KKN-721A KKN-613A PHS-629 LBB-891 PHS-766 P-165 KKN-723A* KKN-767A LBB-891 KKN-768 PHS-764 KKN-769A KKN-773A LBB-891 KKN-735A P-165 MBB-971 KKN-738A LBB-891 PBR-33A KKN-538 KKN-158 CRF-464A CRF-420A CRF-432A CRF-431A KN-538 PHS-550 LBN-738A 1 1 3 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 3 1 DESCRIPTION ....Arm ....Clamp ....Screw (Pkg. of 1) with ......Washer (1/4 Plain) ....Clamp with ......Washer (1/4 Plain) ......Screw (1/4-20 x 1-1/4 Soc. Hd. Cap) ....Clamp (Pkg. of 1) ....Rod (12”) ....Rod (12”) ....Gate with ......Set Screw (10-32 x 5/16 Cup Point) ....Spring ....Latch with ......Set Screw (10-32 x 1/2 Oval Point) ......Latch Pin ....Latch Block with ......Set Screw (10-32 x 1/4 Flat Point) ......Screw (10-32 x 3/4 Soc. Hd. Cap) ....Finger Assembly (Pkg. of 2) includes ......Finger with Pin (Pkg. of 2) ......Carbide Pad Set (Pkg. of 2) with ........Screw (8-32 x 5/16 Flat Hd. Soc. Cap) ......Screw (5/16-18 x 3/4 Soc. Hd. Cap) ......Screw (5/16-18 x 1-1/4 Soc. Hd. Cap) ......Washer (5/16 Plain) ....Finger Set - Optional (Not Supplied with Machine) ....Pivot Block with ......Screw (5/16-18 x 3/4 Soc. Hd. Cap) ......Pivot Pin ......Screw (1/4-28 x 1/2 Soc. Hd. Cap) ....Key ....Stop Block with ......Screw (5/16-18 x 3/4 Soc. Hd. Cap) ....Torque Bracket Assembly with ......Washer (5/16 Plain) ......Screw (5/16-18 x 1 Soc. Hd. Cap) ......Torque Cap ......Screw (5/16-18 x 3/4 Soc. Hd. Cap) ......Bearing with ........Washer (1/2 Plain) ........Locknut (1/2-20 Special) ......Eccentric ....Heavy Work Support with ......Support Rail with Screw & Washer ......Cam (Pkg. of 2) with Screw ......Washer (1/2 Plain) ......Screw (1/2-13 x 1-3/4 Soc. Hd. Cap) ....Arm with N/S indicates Not Shown *KKN_723A Fingers are withour Pads and are used for External Honing. (Parts continued on next page) Page 29 SECTION III POWER STROKER PARTS LIST COVERING FIGURE “K” (cont’d) ITEM NO. 45 37 46 37 47 N/S 48 49 50 51 52 53 N/S N/S N/S N/S N/S 54 55 56 57 ORDER BY PART NUMBER MB-2325A KN-538 AAN-37A KN-538 MB-2331A MB-2333A KKN-742A KKN-197A KKN-198A KKN-680A CRF-546A KKN-196A LN-1546A KN-574A KN-575A KN-229A PHS-14A MBC-400A MBC-475A MBC-480A PHR-335A N/S indicates Not Shown Page 30 QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 DESCRIPTION ......Handle Screw (1/2-20 Thread) with ........Washer (1/2 Plain) ......Clamping Screw with ........Washer (1/2 Plain) ....Offset Bar (13”) ....Offset Bar (23”) - Optional (Not Supplied with Machine) ....Rod (4”) ....Torque Bar (1/2 Diameter) ....Oiler Bar (3/8 Diameter) ....Safety Shield ....Wrench (1” Open End) ....Wrench (1/2 & 5/8 Open End) ....Hex Key Wrench (5/64) ....Hex Key Wrench (1/8) ....Hex Key Wrench (5/32) ....Hex Key Wrench (3/16) ....Hex Key Wrench (7/32) ....Indicator with ......Sliding Block Screw with Ball ......Pivot Rod with ........Retaining Ring SECTION III POWER STROKER FIGURE L - TUBE & SHAFT ASSEMBLY PARTS LIST COVERING FIGURE “L” ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 ORDER BY PART NUMBER MBB-355A KKN-133A KKN-124A PHS-506 PHM-701A KKN-120A KKN-115A KKN-119A KKN-130A KKN-135A PHS-571 QTY. 1 2 2 8 2 2 1 1 1 1 1 DESCRIPTION ....Spring Washer ....Cover Support (Pkg. of 1) ....Seal Retainer (Pkg. of 1) with ......Screw (10-32 x 3/8 Button Hd. Cap) ....Seal (Pkg. of 2) ....Ball & Cage Assembly (Pkg. of 2) ....Bearing Tube Assembly ....Bearing Spacer ....Hub & Shaft Assembly ....Collar Assembly with ......Screw (1/4-20 x 1-1/4 Soc. Hd. Cap) N/S indicates Not Shown Page 31 SECTION III POWER STROKER FIGURE M - CROSS ARM ASSEMBLY PARTS LIST COVERING FIGURE “M” ITEM NO. ORDER BY PART NUMBER QTY. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PHS–610A P-165 KN-172 KKN–412A PHS-611 PNP–339A PHS-532 KKN–424A KKN–425A KN-99 KKN–413A PHW-106 KKN–414A PHS-114 KKN–1915A KKN–1897A KKN–1898A KKN–411A KN-704 KKN–1895A --KKN–1905A 2 2 2 2 8 1 2 1 1 1 1 2 1 2 1 1 1 2 2 1 2 1 N/S indicates Not Shown Page 32 DESCRIPTION ....Shoulder Screw (3/8 x 1–1/2 with 5/16–18 x 1/2 Thd.) (Pkg. of 1) with ......Washer (5/16 Plain) ......Nut (5/16–18 Hex) ....Spacer (Pkg. of 1) with ......Screw (1/4–20 x 5/8 Button Hd. Cap) ....Stroke Length Scale with ......Screw (10–32 x 1/4 Button Hd. Cap) ....Clamp Block ....Clamp Screw Assembly with ......Washer (3/8 Plain) ....Adjusting Screw with ......Washer (9/32 Plain) ....Adjusting Knob with ......Set Screw (10–32 x 3/16 Soc. Cone Pt.) ....Input Bar Assembly with Bearing and Spacer Bushing ....Pin with Set Screw ....Pivot Rod ....Cross Bar (Pkg. of 2) with ......Screw (10–32 x 1/4 Fil. Hd.) ....Moving Block Assembly with ......Bearing (Not recommended to be sold separately) ....Driving Block Assembly with Bearing SECTION IV - ELECTRICAL SYSTEM I TE M 42 FIG. K S E E F I G . B FO R HO O KUP I T E M 1 1 F IG . S FIGURE N - AUTOMATIC SIZE CONTROL PARTS LIST COVERING FIGURE “N” ITEM NO. -1 2 3 4 5 6 7 8 9 ORDER BY PART NUMBER ASC-730A ASC-736A PHSM-515 PHNM-401 ASC-718A ASC-719A PHSM-474 PHWM-501 PHWM-407 PHSM-415 N/S indicates Not Shown QTY. 1 1 2 2 1 1 2 2 2 1 DESCRIPTION ....Probe Body and Clamp Assembly includes ......Platform ......Screw (M8 x 1.25-6G x 25mm Soc. Hd. Cap) ......Nut (M8 x 1.25-6H) ......Bearing Shaft Clamp ......Tee Clamp Block ......Screw (M8 x 1.25-6G x 45mm Soc. Hd. Cap) ......Washer (8mm Lock) ......Washer (8mm Flat) ......Screw (M5 x 0.8 x 35mm Soc. Hd. Cap) (Parts continued on next page) Page 33 SECTION IV ELECTRICAL SYSTEM PARTS LIST COVERING FIGURE “N” (cont’d) ITEM NO. 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 N/S 27 28 29 30 31 32 33 34 -35 36 37 38 39 40 41 N/S 42 43 44 45 46 47 48 49 50 51 52 53 54 ORDER BY PART NUMBER QTY. ASC-757A --PPPM-402A PPPM-401A PHNM-401 ASC-756A PHSM-963 ASC-724A ASC-788A PHSM-516 PHSM-479 PHSM-473 ASC-741A ASC-795A PHP-421A ASC-746A PSP-323A PHP-433A PHPM-507A ASC-753A MBB-335A --ASC-722A ASC-735A PHSM-410 PG-2183A ASC-235A ASC-249A PSP-506A ASC-246A ASC-236A PHSM-520 ASC-248A PG-697 PHW-156 ASC-773A PHSM-963 PHWM-502 PHSM-410 PEM-407A ASC-230A CRG-299E PHM-301A PES-160A PES-161A PEM-408A 78161A 78161A 1 1 2 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 2 2 2 1 1 1 1 1 1 1 * * N/S indicates Not Shown Page 34 DESCRIPTION ......Air Cylinder includes ........Nut ......Reducing Nipple (Pkg. of 1) ......Flow Control Valve (Pkg.of 1) ......Nut (M8 x 1.25-6H) ......Position Bracket ......Screw (M5 x 0.8-6G x 20mm Soc. Hd. Cap) ......Bearing Assembly ......Probe Extension Arm ......Screw (M5 x 0.8-6G x 25mm Soc. Hd. Cap) ......Set Screw (M8 x 1.25-6G x 12mm Flat Point) ......Screw (M4 x 0.7-6G x 40mm Soc. Hd. Cap) ......Pivot Post ......Pivot Assembly ......Roll Pin ......Spring Support ......Spring with ........Roll Pin ......Dowel Pin ......Guide Rod ......Bearing includes ........Retaining Ring ......Bearing Block ......Knob and Shaft Assembly ......Set Screw (M5 x 0.8 x 8mm) ......Nylon Plunger ....Plunger Assembly includes ......Sealing Boot ......Coned Spring ......Plunger ......Plunger Nose ......Screw (8-32 x 3/8 Soc. Hd. Cap) ......Collar ......Screw (8-32 x 5/16 Soc. Hd. Cap) ....Washer (#8 Shakeproof) ....Probe Body with ......Screw (M5 x 0.8-6G x 20mm Soc. Hd. Cap) ......Washer ......Set Screw (M5 x 0.8 x 8mm) ....Proximity Sensor ....Conduit Assembly ....Switch ....Knob ....Solenoid, Wires, Markers and Screws ....Potentiometer, Wires and Markers ....Rate Sensor Board Assembly ....Tubing (5/32 O.D. Orange) ....Tubing (5/32 O.D. Orange) *Material sold by the foot only. SECTION IV ELECTRICAL SYSTEM FIGURE O - ELECTRICAL CONTROL ENCLOSURE (NON-CE MACHINES) PARTS LIST COVERING FIGURE “O” ITEM NO. 1 N/S N/S 2 3 4 5 6 7 8 9 10 11 ORDER BY PART NUMBER --PEM-319A MBC-567A PEF-115A PES-297A PEF-114A PES-718 PES-728 PES-725 PES-724 PES-724 PEM-532A PEM-1095 QTY. 1 1 1 3 1 1 3 1 1 1 1 1 3 DESCRIPTION ....Enclosure (For Non “CE” Machines) with ......Disconnect Handle ......Extension Shaft ....Fuse, Time Lag Diazed (Pkg. of 1) ....Non-Fused Disconnect Switch ....Fuse, 2 Amp, Slo-Blo ....Contactor (Pkg. of 1) ....Pneumatic Timer ....Overload Relay ....Overload Relay ....Overload Relay ....Control Transformer ....AC Coil Suppressor / Adapter N/S indicates Not Shown Page 35 SECTION IV ELECTRICAL SYSTEM FIGURE P - ELECTRICAL CONTROL ENCLOSURE (NON-CE MACHINES) Page 36 SECTION IV ELECTRICAL SYSTEM PARTS LIST COVERING FIGURE “P” ITEM NO. 1 N/S N/S 2 2 3 4 5 6 7 7 8 8 9 9 10 10 11 12 ORDER BY PART NUMBER --PEM-319A MBC-567A PEF-21A PEF-24A PES-297A PEF-114A PES-718 PES-728 PES-724 PES-725 PES-724 PES-725 PEF-22A PEF-25A PEF-23A PEF-26A PEM-532A PEM-1095 QTY. 1 1 1 3 3 1 1 3 1 1 1 1 1 3 3 2 2 1 3 DESCRIPTION ....Enclosure (For Non “CE” Machines) with ......Disconnect Handle ......Extension Shaft ....Fuse, 12 Amp (Pkg. of 1) for (208/230V, 60Hz, 3Ph & 220V, 50Hz, 3Ph) ....Fuse, 6 Amp (Pkg. of 1) for (440V, 50Hz, 3Ph & 460V, 60Hz, 3Ph) ....Non-Fused Disconnect Switch ....Fuse, 2 Amp, Slo-Blo ....Contactor (Pkg. of 1) ....Pneumatic Timer ....Overload Relay for (440V, 50Hz, 3Ph & 460V, 60Hz, 3Ph) ....Overload Relay for (208/230V, 60Hz, 3Ph & 220V, 50Hz, 3Ph) ....Overload Relay for (440V, 50Hz, 3Ph & 460V, 60Hz, 3Ph) ....Overload Relay for (208/230V, 60Hz, 3Ph & 220V, 50Hz, 3Ph) ....Fuse, 5.6 Amp (Pkg. of 1) for (208/230V, 60Hz, 3Ph & 220V, 50Hz, 3Ph) ....Fuse, 3 Amp (Pkg. of 1) for (440V, 50Hz, 3Ph & 460V, 60Hz, 3Ph) ....Fuse, 1.5 Amp (Pkg. of 1) for (208/230V, 60Hz, 3Ph & 220V, 50Hz, 3Ph) ....Fuse, .75 Amp (Pkg. of 1) for (440V, 50Hz, 3Ph & 460V, 60Hz, 3Ph) ....Control Transformer ....AC Coil Suppressor / Adapter N/S indicates Not Shown Page 37 SECTION IV ELECTRICAL SYSTEM FIGURE Q - ELECTRICAL CONTROL ENCLOSURE (CE MACHINES) Page 38 SECTION IV ELECTRICAL SYSTEM PARTS LIST COVERING FIGURE “Q” ITEM NO. 1 N/S N/S 2 3 4 5 6 7 7 7 8 8 9 9 10 11 12 13 ORDER BY PART NUMBER --PEM-319A MBC-567A PEF-115A PES-297A PEF-114A PES-718 PES-728 PES-746 PES-725 PES-747 PES-725 PES-724 PES-725 PES-724 PES-729 PES-729 PEM-532A PEM-1095 QTY. 1 1 1 3 1 1 3 1 1 1 1 1 1 1 1 3 1 1 3 DESCRIPTION ....Enclosure (For “CE” Machines) with ......Disconnect Handle ......Extension Shaft ....Fuse, Time Lag Diazed (Pkg. of 1) ....Non-Fused Disconnect Switch ....Fuse, 2 Amp, Slo-Blo ....Contactor (Pkg. of 1) ....Pneumatic Timer ....Overload Relay (220V, 50Hz, 3Ph) ....Overload Relay (400V, 50Hz, 3Ph) ....Overload Relay (440V, 50Hz, 3Ph) ....Overload Relay (220V, 50Hz, 3Ph) ....Overload Relay (400/440V, 50Hz, 3Ph) ....Overload Relay (220V, 50Hz, 3Ph) ....Overload Relay (400/440V, 50Hz, 3Ph) ....Control Relay (Pkg. of 1) ....Relay ....Control Transformer ....AC Coil Suppressor / Adapter N/S indicates Not Shown Page 39 SECTION IV ELECTRICAL SYSTEM 2C 4B FIGURE R - CONTROL BOX Page 40 SECTION IV ELECTRICAL SYSTEM PARTS LIST COVERING FIGURE “R” ITEM NO. ORDER BY PART NUMBER QTY. 1 2 2 2A 2B 2C 3 3A 4 4A 4B 5 5A 6 6A 6B 7 7A 8 9 10 11 12 13 14 15 16 17 18 19 --PES-755A PES-495A PES-761A PES-762A PES-763A PES-756A PES-763A PES-757A PES-763A PES-764A PES-758A PES-765A PES-759A PES-763A PES-765A PES-760A PES-765A PNP-335A MBB-856A MBC-267A MBC-266A MBC-265A PHN-134 MBB-3172A PHS-506 PHN-134 MBB-3169A MBB-3205A MBB-3218A 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 * 1 1 1 1 1 1 1 4 1 2 2 1 1 1 DESCRIPTION ....Switch Box ....3 Position Selector Switch (For Non “CE” Machines) ....Key Selector Switch (For “CE” Machines) ....Contact Block (Two Contact NO/NC)(Pkg. of 1) ....Contact Block - (Two Contact NO/NC) ....Contact Block (NO) ....Switch (Cycle Start) ....Contact Block (NO) ....Pushbutton Unit (Power On) ....Contact Block (NO) ....Light ....Flush Pushbutton Switch (Power Off) ....Contact Block (NC) ....Extended Pushbutton Switch (Cycle Stop / Reset) ....Contact Block (NO) ....Contact Block (NC) ....Switch (E-Stop) ....Contact Block (NC) ....Nameplate ....Neoprene Bumper ....Drain Tube with Bushings ....Tray Pad ....Tray ....Nut & Lockwasher ....Switch Box Angle ....Screw (10-32 x 3/8 Button Hd. Cap) ....Nut (10-32 Hex) ....Side Cover ....Work Tray ....Tray Pad N/S indicates Not Shown *1 Contact block required for Non CE Machines. 2 Contact blocks required for CE Machines. Page 41 SECTION V - COVERS & GUARDS FIGURE S - SHEET METAL COVERS & LATCHES PARTS LIST COVERING FIGURE “S” ITEM NO. ORDER BY PART NUMBER QTY. 1 2 3 4 5 6 7 8 KKN-1630A KKN-1519A KKN-458A PHW-118 MSA-219 KKN-1647A KKN-1715A MBC-701A 1 1 3 1 1 1 1 1 N/S indicates Not Shown Page 42 DESCRIPTION ....Filter Door Assembly with ......Pilot with Washer and Screw ......Knob (Pkg. of 1) with ........Washer (1/4 Lock) ........Screw (1/4-20 x 1/2 Hex. Hd. Cap) ....Bumper Set - Left Side ....Door Assembly ....Cover Restraint (Parts continued on next page) SECTION V COVERS & GUARDS PARTS LIST COVERING FIGURE “S” (cont’d) ITEM NO. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 N/S 30 -31 32 33 -32 33 34 35 36 37 38 N/S 39 40 41 42 43 44 45 46 47 48 ORDER BY PART NUMBER PHS-674 PF-287A KKN-1624A PNP-338A KKN-1748A KKN-1622A KKN-1619A KKN-1618A KKN-1620A KKN-1612A --KKN-1512A KKN-1712A KKN-2066A PHS-672 MSN-189 PHW-118 LBN-431 KKN-1615A PF-309 KKN-1657A KKN-455A PHS-506 PNP-337A --KKN-1705A KKN-1744A KKN-1743A --MBC-747A MBC-746A PHM-746 MBC-742A PEM-734A MBC-743 PHS-506 PHN-134 PES-494A PHS-715 PG-605 PHN-134 MBC-741A MBC-739 LBN-401 PHS-602 PHW-118 LBN-431 QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 2 1 1 1 1 2 1 2 1 2 2 2 2 2 2 1 1 2 1 1 1 DESCRIPTION ....Screw (8-32 x 1/2 Binding Hd.) ....Bushing ....Cover Support ....Stroke Length Selector Label ....Bumper Set - Right Side ....Wrap Around includes ......Right Panel ......Rear Panel ......Left Panel ....Front Strip ....Rear Splash Guard (See Fig. E) ....Tap Strip ....Tap Strip ....Front Cover with ......Screw (1/4-20 x 1 Button Hd, Cap) ......Washer ......Washer (1/4 Lock) ......Nut (1/4-20 Hex.) ....Side Panel Assembly with ......Caplug ....Rear Plate ....Lower Door with ......Screw (10-32 x 1/4 Button Hd. Cap) ......Stroke Speed Selector Chart FOLLOWING PARTS ARE FOR NON “CE” MACHINES ....Safety Latch (Pkg. of 1) ....Bumper Strip ....Bumper Strip FOLLOWING PARTS ARE FOR “CE” MACHINES ....Bumper Strip ....Bumper Strip ....Button Plug ....Safety Key Bracket ....Safety Key (Pkg. of 1) ....Switch Bracket ....Screw (10-32 x 3/8 Button Hd. Cap) ....Nut and Lockwasher ....Safety Interlock (Pkg. of 1) with ......Screw (8-32 x 1-1/4 Soc. Hd. Cap) ......Washer ......Nut and Lockwasher ....Switch Bracket ....Safety Key Plate ....Washer ....Screw (1/4-20 x 1-1/2 Hex. Hd. Cap) ....Lockwasher ....Nut (1/4-20 Hex.) N/S indicates Not Shown Page 43 SECTION V COVERS & GUARDS FIGURE T - BELT GUARD ASSEMBLY Page 44 SECTION V COVERS & GUARDS PARTS LIST COVERING FIGURE “T” ITEM NO. ORDER BY PART NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -16 17 18 19 20 -21 22 23 24 25 26 27 28 29 30 31 32 33 KKN-970A PNP-336A MBB-1019A PHS-506 MAN-1028 LBN-401 KKN-960A MSA-219 PHW-118 PHS-652 AN-13B KN-567 KN-568 PHW-119 KN-172 --MBB-807A MBB-806 MBB-804 AN-15A PHN-121 --KKN-458A MBB-804 MBC-738 PHS-560 PHW-118 PEM-734A PHS-506 LBA-451 PES-494A PHS-715 PG-605 MBC-737 PHS-571 QTY. 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 2 1 2 2 1 1 DESCRIPTION ....Belt Guard Assembly with ......Spindle Speed Selection Chart ......Upper Support ......Screw (10-32 x 3/8 Button Hd. Cap) ......Screw (1/4-20 x 3/4 Hex. Hd. Cap) ......Washer (1/4 Plain) ......Belt Guard Bracket with ........Screw (1/4-20 x 1/2 Hex. Hd. Cap) ........Lockwasher ......Screw (1/4-20 x 1/2 Button Hd. Cap) ......Lockwasher ......Screw (5/16-18 x 3/4 Hex. Hd. Cap) ......Washer (5/16 Plain) ......Lockwasher ......Nut (5/16-18 Hex.) FOLLOWING PARTS ARE FOR NON “CE” MACHINES ......Latch ......Latch Pivot ......Washer (1/4 Special) ......Spring ......Nut (1/4-20 Hex. Self-Locking) FOLLOWING PARTS ARE FOR “CE” MACHINES ......Knob ......Washer (1/4 Special) ......Safety Key Block ......Screw (1/4-20 x 1-1/4 Hex. Hd. Cap) ......Lockwasher ......Safety Key ......Screw (10-32 x 3/8 Button Hd. Cap) ......Washer (Shakeproof) ....Safety Interlock ....Screw (8-32 x 1-1/4 Soc. Hd. Cap) ....Washer ....Switch Mounting Block ....Screw (1/4-20 x 1-1/4 Soc. Hd. Cap) N/S indicates Not Shown Page 45 SECTION V COVERS & GUARDS FIGURE U - WORK AREA COVER Page 46 SECTION V COVERS & GUARDS PARTS LIST COVERING FIGURE “U” ITEM NO. -1 2 3 4 5 6 7 8 9 10 11 12 13 14 N/S N/S 15 16 -17 18 19 20 21 22 23 24 25 26 22 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 ORDER BY PART NUMBER MBC-755 MBC-836A MBC-830A MBC-824 MBC-828 PHM-351A KN-568 MBC-826 MBC-837 MBC-841 MBC-843 MBC-839 PHS-683 PEM-737A PHS-715 PG-605 CL-26 PES-493A PEC-193 MBC-750 MBC-821A PHS-652 PHK-109A MBC-818 MBC-816 AG-128 PBR-171A PHS-971 MBC-813 MBC-811 AG-128 MBC-845 AN-320 ----MBC-858 LBA-150 MBC-856 MBC-854A MBC-857A MBC-852 ----PPP-328 MBC-859A PPP-370 PPP-242 PPPM-430 PFC-126A PPPM-406 78160A MBC-851 N/S indicates Not Shown DESCRIPTION QTY. 1 1 1 1 1 2 2 2 2 1 1 1 4 1 2 2 2 1 1 1 1 4 1 1 1 4 2 1 1 1 4 1 2 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 * 1 ....Adjustable Work Area Cover includes ......Bottom Cover ......Top Cover Assembly ......Top Mounting Rail - Left Hand ......Top Mounting Rail - Right Hand ......Plastic Knob (Pkg. of 1) ......Washer ......Stud ......Bottom Mounting Rail ......Left Top Slide Rail ......Right Top Slide Rail ......Tie Bar ......Screw (10-32 x 5/8 Button Hd. Cap) ......Magnet Actuator ......Screw (8-32 x 1-1/4 Soc. Hd. Cap) ......Washer ......Nut (8-32 Hex.) ......Magnetic Proximity Sensor ......Cord Grip Cover Support Linkage includes ......Axle ......Screw (1/4-20 x 1/2 Button Hd. Cap) ......Key ......Bracket Support - Right Side ......Bracket - Right Side ......Screw (10-32 x 3/4 Soc. Hd. Cap) ......Teflon Bearing (Pkg. of 2) ......Shoulder Screw (1/2-16 x 1-1/4 Soc. Hd. Cap) ......Bracket Support - Left Side ......Bracket - Left Side ......Screw (10-32 x 3/4 Soc. Hd. Cap) ......Crank Assembly ......Set Screw (10-32 x 1/4 Cup Point) ......Pin ......Retaining Ring ......Rod Clevis ......Nut (3/8-24 Hex.) ......Cylinder Extension ......Air Cylinder ......Reed Switch ......Pivot Bracket ......Pin ......Retaining Ring ......Adapter ......Blocking Valve ......Adapter ......Reducing Bushing ......Nipple ......Regulator ......Male Run Tee ......Tubing (5/32 O.D. Yellow) ....Mounting Block *Sold by the foot only. Page 47 SECTION V COVERS & GUARDS Page 48 Like any machinery, this equipment may be dangerous if used improperly. Be sure to read and follow instructions for operation of equipment. FRACTION / DECIMAL / MILLIMETER EQUIVALENTS CHART INCH FRACTION DECIMAL MILLIMETER INCH FRACTION DECIMAL MILLIMETER INCH FRACTION DECIMAL MILLIMETER .... .003937 0,1000 9/32 .281250 7,1438 21/32 .656250 16,6688 .... .007874 0,2000 19/64 .296875 7,5406 .... .669291 17,0000 .... .011811 0,3000 5/16 .312500 7,9375 43/64 .671875 17,0656 1/64 .015625 0,3969 .... .314961 8,0000 11/16 .687500 17,4625 .... .015748 0,4000 21/64 .328125 8,3344 45/64 .703125 17,8594 .... .019685 0,5000 11/32 .343750 8,7313 .... .708661 18,0000 .... .023622 0,6000 .... .354331 9,0000 23/32 .718750 18,2563 .... .027559 0,7000 23/64 .359375 9,1281 47/64 .734375 18,6531 1/32 .031250 0,7938 3/8 .375000 9,5250 .... .748031 19,0000 .... .031496 0,8000 25/64 .390625 9,9219 3/4 .750000 19,0500 .... .035433 0,9000 .... .393701 10,0000 49/64 .765625 19,4469 .... .039370 1,0000 13/32 .406250 10,3188 25/32 .781250 19,8438 3/64 .046875 1,1906 27/64 .421875 10,7156 .... .787402 20,0000 1/16 .062500 1,5875 .... .433071 11,0000 51/64 .796875 20,2406 5/64 .078125 1,9844 7/16 .437500 11,1125 13/16 .812500 20,6375 .... .078740 2,0000 29/64 .453125 11,5094 .... .826772 21,0000 3/32 .093750 2,3813 15/32 .468750 11,9063 53/64 .828125 21,0344 7/64 .109375 2,7781 .... .472441 12,0000 27/32 .843750 21,4313 .... .118110 3,0000 31/64 .484375 12,3031 55/64 .859375 21,8281 1/8 .125000 3,1750 1/2 .500000 12,7000 .... .866142 22,0000 9/64 .140625 3,5719 .... .511811 13,0000 7/8 .875000 22,2250 5/32 .156250 3,9688 33/64 .515625 13,0969 57/64 .890625 22,6219 .... .157480 4,0000 17/32 .531250 13,4938 .... .905512 23,0000 11/64 .171875 4,3656 35/64 .546875 13,8906 29/32 .906250 23,0188 3/16 .187500 4,7625 .... .551181 14,0000 59/64 .921875 23,4156 .... .196850 5,0000 9/16 .562500 14,2875 15/16 .937500 23,8125 13/64 .203125 5,1594 37/64 .578125 14,6844 .... .944882 24,0000 7/32 .218750 5,5563 .... .590551 15,0000 61/64 .953125 24,2094 15/64 .234375 5,9531 19/32 .593750 15,0813 31/32 .968750 24,6063 .... .236220 6,0000 39/64 .609375 15,4781 .... .984252 25,0000 1/4 .250000 6,3500 5/8 .625000 15,8750 63/64 .984375 25,0031 17/64 .265625 6,7469 .... .629921 16,0000 1 1.000000 25,4000 .... .275591 7,0000 41/64 .640625 16,2719 1-1/16 1.062500 26,9880 FORMULAS: MULTIPLY INCHES (in) FEET (ft) x x BY 25.4 0.3048 = = TO GET MILLIMETERS (mm) METERS (m) MULTIPLY MILLIMETERS (mm) METERS (m) x x BY 0.03937 3.281 = = TO GET INCHES (in) FEET (ft) “SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN® PRODUCTS COMPANY.” Sunnen® reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing. Should any discrepancy of information arise, Sunnen recommends that user verify discrepancy with Sunnen before proceeding. PRINTED IN U.S.A. 0409 SUNNEN PRODUCTS COMPANY 7910 Manchester Ave., St. Louis, MO 63143 U.S.A. Phone: 314-781-2100 Fax: 314-781-2268 U.S.A. Toll-Free Sales and Service – Automotive: 1-800-772-2878 • Industrial: 1-800-325-3670 International Division Fax: 314-781-6128 http://www.sunnen.com e-mail: sunnen@sunnen.com SUNNEN PRODUCTS LIMITED No. 1 Centro, Maxted Road Hemel Hempstead, Herts HP2 7EF ENGLAND Phone: ++ 44 1442 39 39 39 Fax: ++ 44 1442 39 12 12 SUNNEN AG Fabrikstrasse 1 8586 Ennetaach-Erlen, Switzerland Phone: ++ 41 71 649 33 33 Fax: ++ 41 71 649 34 34 SHANGHAI SUNNEN MECHANICAL CO., LTD. 889 Kang Qiao East Road, PuDong Shanghai 201319, P.R. China Phone: 86 21 5 813 3322 Fax: 86 21 5 813 2299 SUNNEN ITALIA S.R.L. Viale Stelvio 12/15 20021 Ospiate di Bollate (MI) Italy Phone: 39 02 383 417 1 Fax: 39 02 383 417 50 ©COPYRIGHT SUNNEN® PRODUCTS COMPANY 2004, ALL RIGHTS RESERVED