Download Sears Microwave Oven Service manual
Transcript
TECHNICAL FLASH T.F. 22-480 Department 731A Toronto BASIC SERVICE MANUAL FOR MICROWAVE OVEN MODEL 767.8541000 / 767.8541001 767.8541300 / 767.8541301 767.8541900 / 767.8541901 MARCH, 2005 CAUTION SAFETY PRECAUTIONS PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY a. Do not operate or allow the oven to be operated with the door open. b. Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary; (1) Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse. c. Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections. d. Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. e. A Microwave leakage check to verify compliance with the CSA Standard should be performed on each oven prior to release to the owner. • Proper operation of the microwave ovens requires that the magnetron be assembled to the wave guide and cavity. Never operate the magnetron unless it is properly installed. • Be sure that the magnetron gasket is properly installed around the dome of the tube whenever installing the magnetron. • Routine service safety procedures should be exercised at all times. • Untrained personnel should not attempt service without a thorough review of the test procedures and safety information contained in this manual. FOREWORD Read this Manual carefully. Failure to adhere to or observe the information in this Manual may result in exposing yourself to the Microwave Energy normally contained within the oven cavity. TABLE OF CONTENTS (Page) SAFETY PRECAUTIONS ................................................................................................................... Inside front page SPECIFICATIONS..................................................................................................................................................... 1-1 CAUTIONS ............................................................................................................................................................... 2-1 INSTALLATION ....................................................................................................................................................... 3-1 OPERATING INS ..................................................................................................................................................... 4-1 CONTROL PANEL............................................................................................................................................. 4-1 CONTROL PANEL INSTRUCTIONS................................................................................................................. 4-2 OVERALL CIRCUIT DIAGRAM................................................................................................................................. 5-1 SCHEMATIC...................................................................................................................................................... 5-1 MATRIX CIRCUIT FOR TOUCH KEY BOARD ................................................................................................. 5-2 GENERAL INFORMATION FOR SERVICE.............................................................................................................. 6-1 GENERAL PRECAUTIONS IN USE.................................................................................................................. 6-1 TRIAL OPERATION .......................................................................................................................................... 6-1 FEATURES AND SPECIFICATIONS FEATURES............................................................................................ 6-1 SERVICE INFORMATION......................................................................................................................................... 7-1 PRECAUTIONS AND REPAIR SERVICE TIPS ................................................................................................ 7-1 MICROWAVE LEAKAGE TEST......................................................................................................................... 7-2 POWER OUTPUT MEASUREMENT................................................................................................................. 7-3 DISASSEMBLY INSTRUCTIONS...................................................................................................................... 7-4 INTERLOCK SYSTEM..................................................................................................................................... 7-12 INTERLOCK CONTINUITY TEST ................................................................................................................... 7-14 TEST AND CHECKOUT PROCEDURES AND TROUBLE SHOOTING ......................................................... 7-15 A. TEST PROCEDURES .......................................................................................................................... 7-15 B. CHECKOUT PROCEDURES ............................................................................................................... 7-18 C. TROUBLE SHOOTING ........................................................................................................................ 7-21 EXPLODED VIEW..................................................................................................................................................... 8-1 REPLACEMENT PARTS LIST........................................................................................................................... 8-8 SPECIFICATIONS Rated Power Consumption - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1500W maximum (Microwave oven+Cook top lamps+Ventilation fan) Microwave Output - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1000W (IEC60705) Adjustable 100W through 1000W, 10 steps Frequency - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2450 MHz ± 50 MHz Power Supply - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 120 VAC, 60 Hz Rated Current - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13 Amp. (Microwave oven+Cook top lamp+Ventilation fan) Magnetron Cooling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Forced Air Cooling Rectification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Rectification Voltage Double Half-Wave Door Sealing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Choke System Safety Devices - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Oven Cavity Thermostat: Open at 90°C ± 5°C Fuse(20A) Primary Interlock Switch Secondary Interlock Switch Interlock Monitor Magnetron - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2M214-161GP High Voltage Capacitor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Capacitor: 1.0µF, 2.1 KV AC High Voltage Diode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Diode; 350mA, 9.0 KV Cook top Lamp - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 125 V, 30 W Cavity Lamp - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 125 V, 30 W Timer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Digital, up to 99 mim. 99 sec. (in each cooking stage) Tray - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Tempered Safety Glass Overall Dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2915/16"(W)x167/16"(D)x153/8"(H) Oven Cavity Size - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 197/8"(W)x143/16"(D)x815/16"(H) Effective Capacity of Oven Cavity - - - - - - - - - - - - - - - - - - - - - - - 1.6 Cu.ft. Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Owner’s Manual & Cooking Guide, Installation Manual, Exhaust Adapter, Exhaust Damper, Mounting Kit and Two Filters, Rotating Ring Assembly. 1-1 CAUTIONS Unlike other appliances, the microwave oven is high-voltage and high-current equipment. Though it is free from danger in ordinary use, extreme care should be taken during repair. MICROWAVE RADIATION Personnel should not be exposed to the microwave energy which may radiate from the magnetron or other microwave generating device if it is improperly used or connection. All input and output microwave connections, waveguide, flange, and gasket must be secure. Never operate the device without a microwave energy absorbing load attached. Never look into an open waveguide or antenna while the device is energized. • DO NOT operate on a 2-wire extension cord during repair and use. • NEVER TOUCH any oven components or wiring during operation. • BEFORE TOUCHING any parts of the oven, always remove the power plug from the outlet. • For about 30 seconds after the oven stops, an electric charge remains in the high voltage capacitor. When replacing or checking, you must discharge the high voltage capacitor by shorting across the two terminals with an insulated screwdriver. • Proper operation of the microwave oven requires that the magnetron be assembled to the waveguide and cavity. Never operate the magnetron unless it is properly installed. • Be sure that the magnetron gasket is properly installed around the dome of the tube whenever installing the magnetron. ANTENNA Gasket COOLING FIN FILAMENT TERMINALS MAGNETRON CHASSIS GROUND • Remove your watches whenever working close to or replacing the Magnetron. • DO NOT touch any parts of the control panel circuit. A resulting static electric discharge may damage this P.C.B. • NEVER operate the oven with no load. • NEVER injure the door seal and front plate of the oven cavity. • NEVER put iron tools on the magnetron. • NEVER put anything into the latch hole and the interlock switches area. MAGNETRON THE OVEN IS TO BE SERVICED ONLY BY PROPERLY QUALIFIED SERVICE PERSONNEL. 2-1 INSTALLATIONS BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY. PRECAUTIONS ON INSTALLATION A. Plug the power supply cord into a 120V AC, 60Hz, single-phase power source with a capacity of 15A or 20A. B. Avoid placing the unit in a location where there is direct heat or splashing water. C. Install the unit on the mounting plate firmly. D. Place the unit as far away as possible from TV, radio, etc. to prevent interference. GROUNDING INSTRUCTIONS For personal safety, this appliance must be fully grounded at all times. In the event of an electrical short circuit, grounding reduces the risk of electrical shock. The plug must be plugged into an outlet that is properly installed and grounded. CAUTION This unit is equipped with a 3-prong plug for your safety. If the wall outlet is a grounded 3-hole type, the unit will be grounded automatically. Plug with Ground Prong Properly Polarized and Grounded Outlet WARNING Improper use of the grounding plug can result in a risk of electric shock. Do not, under any circumstances, cut or remove the third ground prong from the power cord plug. 3-1 OPERATING INSTRUCTIONS CONTROL PANEL For Model 85410 4-1 CONTROL PANEL INSTRUCTIONS 1. DISPLAY: The Display includes a clock and indicators to tell you time of day, cooking time settings and cooking functions selected. 14. TIME: Touch this pad to set a cooking time. 2. POPCORN: Touch this pad when popping popcorn in your microwave oven. 16. CUSTOM SET: Touch this pad to change the oven’s default settings for sound, clock, display speed and defrost weight. 15. POWER: Touch this pad to select a cooking power level. 3. PIZZA: Touch this pad to reheat 1 to 3 slices. 17. TIME OF DAY: Touch this pad to enter the time of day. 4. COOK: Touch this pad to cook vegetables, rice, or casseroles. 5. POTATO: Touch this pad to cook potatoes from 1 to 4. 18. HOLD WARM: Touch this pad to keep hot, cooked foods safety warm in your microwave oven for up to 99 minutes 99 seconds. 6. BEVERAGE: Touch this pad to reheat one cup or two cups a beverage. 19. HELP: Touch this pad to learn how to use each oven function. 7. REHEAT: Touch this pad to reheat dinner plate, soup/sauce, casserole, roll/muffin. 20. STOP/CLEAR: Touch this pad to stop the oven or clear all entries. 8. MORE: Touch this pad to add ten seconds of cooking time each time you press it. 21. START: Touch this pad to start a function. If you open the door after oven begins to cook, retouch START. 9. CUSTOM COOK: Touch this pad to recall one cooking instruction previously programmed into memory. 22. KITCHEN TIMER: Touch this pad to set the kitchen timer. 10. LESS: Touch this pad to subtract ten seconds of cooking time each time you press. 23. 11. EXPRESS DEFROST: Meat, poultry, fish. Touch on pad to select food type and defrost food by weight. 24. LIGHT TIMER: Touch this pad to set the light timer. ON/OFF: Touch this pad to turn off the turntable. “OFF” will appear in the display. 25. HI/LOW/OFF: Touch this pad to turn the fan on or off. 12. QUICK TOUCH PLUS: Touch this pad to set and start quickly at 100% power level. 26. 13 NUMBER: Touch number pads to enter cooking time, power level, quantities or weights. 4-2 HI/LOW/OFF: Touch this pad to turn on the cooktop/countertop light. OVERALL CIRCUIT DIAGRAM SCHEMATIC DIAGRAM 5-1 MATRIX CIRCUIT FOR TOUCH KEY BOARD 5-2 GENERAL INFORMATION FOR SERVICE GENERAL PRECAUTIONS IN USE FEATURES AND SPECIFICATIONS FEATURES A. Never operate the unit when it is empty. Operating the oven with no load may shorten the life of the magnetron. Whenever cooking dry foods (dried fish, bread, etc.) or a small amount of food, be sure to put a glass of water into the cooking compartment. The glass turntable may become hot after operating, be careful when touching it. B. Aluminum foil should be avoided because it will disrupt cooking and may cause arcing. However, small pieces may be used to cover some parts of food to slow the cooking. Any aluminum foil used should never be closer than 2.5 cm to any side wall of the oven. A. The safety systems incorporated in this model are: (1) Primary interlock switch (2) Secondary interlock switch (3) Interlock monitor switch (4) Choke system (5) Magnetron thermal fuse (6) Oven cavity thermostat (Note: This thermostat located on the oven cavity will open and stop the unit from operation only if a high temperature is reached, such as, a fire created by overcooking food.) B. Any one of 10 power output levels ranging 100W to 1000W can be selected by the touch control and electronic computer system. TRIAL OPERATION After installation, the following sequences and results should be checked carefully. A. Put a container filled with water (about 1 liter) into the oven, and close the door tightly. B. Set cooking time for 10 minutes by touching “1” and then “0” three times. “1, 0, 0, 0” appears in the display window. C. Touch the START key. Make sure the cavity light comes on. The unit will begin cooking and the display window will show the time counting down by seconds. D. After about 5 minutes, make sure the primary interlock switch, the secondary interlock switch and the interlock monitor switch operate properly by opening and closing the door several times. Touch the START key each time the door is closed. E. Continue operating the unit. Four long beep sound signal is heard when the time is up. The unit will shut off automatically. F. Confirm the water is hot. G. Finally, measure the output power according to “POWER OUTPUT MEASUREMENT” on page 7-3. 6-1 SERVICE INFORMATION PRECAUTIONS AND REPAIR SERVICE TIPS PRELIMINARY (3) Do not operate the unit until it is completely repaired, if any of the following conditions exist. The unit must not be operated. (a) The door does not close firmly. (b) The hinge is broken. (c) The door seal is damaged. (d) The door is bent or warped, or there is any other visible damage on the unit that may cause microwave energy leakage. NOTE: Always keep the seal clean. (e) Make sure that there are no defective parts in the interlock mechanism. (f) Make sure that there are no detective parts in the microwave generating and transmission assembly (especially waveguide). A. SINCE NEARLY 2,100 VOLTS EXISTS IN SOME CIRCUITS OF THIS UNIT REPAIRS SHOULD BE CARRIED OUT WITH GREAT CARE. The filament leads of magnetron carry High Voltage with respect to ground. Extreme caution must be exercised. Never plug the unit into a power source to determine which component is defective in high voltage section. B. TO AVOID POSSIBLE EXPOSURE TO MICROWAVE ENERGY LEAKAGE, THE FOLLOWING PRECAUTIONS MUST BE TAKEN BEFORE SERVICING. (1) Before the power is applied: (a) Make sure the primary interlock switch, the secondary interlock switch and the interlock monitor switch operate properly by opening and closing the door several by opening and closing the door several times. (b) Make sure the perforated screen and the dielectric choke of the door are correctly and firmly mounted. (4) The following items should be checked after the unit is repaired: (a) The interlock monitor switch is connected correctly and firmly. (b) The magnetron gasket is properly positioned and mounted. (c) The waveguide and the oven cavity are intact. (no microwave energy leakage) (d) The door can be properly closed and the safety switches work properly. (e) The unit must stop when the door is opened or the time is up. (2) After power is applied: (a) Make sure the interlock switch mechanism is operating properly by opening and closing the door. (b) Check microwave energy leakage must bebelow the limit of 5 mW/cm2. (All service adjustments should be made for minimum microwave energy leakage readings). The unit must not be operated with any of the above components removed or by-passed. 7-1 MICROWAVE LEAKAGE TEST CAUTIONS MEASURING MICROWAVE ENERGY LEAKAGE • Be sure to check microwave leakage prior to servicing the oven if the oven is operative prior to servicing. • The service personnel should inform the manufacture importer, or assembler of any certified oven unit found to have a microwave emission level in excess of 5 mW/cm2 and should repair any unit found to have excessive emission levels at no cost to the owner, and should ascertain the cause of the excessive leakage. The service personnel should instruct the owner not to use the unit until the oven has been brought into compliance. • If the oven operates with the door open, the service personnel should: - Tell the user not to operate the oven. • The service personnel should check all surface and vent openings for microwave leakage. • Check for microwave leakage after every servicing. The power density of the microwave radiation leakage emitted by the microwave oven should not exceed 4 mW/cm2. Always start measuring of an unknown field to assure safety for operating personnel from radiation leakage. • Pour 275±15cc of 20±5°C(68±9°F) water in a beaker which is graduated to 600 cc, and place the beaker on the center of the turntable. • Set the energy leakage monitor to 2,450 MHz and use it following the manufacturer's recommended test procedure to assure correct result. • When measuring the leakage, always use the 2-inch (5cm) spacer supplied with the probe. • Operate the oven at its maximum output. • Measure the microwave radiation using an electromagnetic radiation monitor by holding the probe perpendicular to the surface being measured. Move probe along shaded area. Probe scanning speed Less than 2.5 cm/sec. ( 1 in/sec) EQUIPMENT • TESTER (VOLTS-DC, AC, Ohmmeter) • Microwave survey meter - Holaday HI-1500 HI-1501 - Narda 8100 8200 • 600 cc non conductive material beaker (glass or plastic), inside diameter: approx. 8.5 cm (31/2 in.) • Glass thermometer: 100°C or 212°F (1 deg scale) 7-2 MEASUREMENT WITH THE OUTER CASE REMOVED NOTE WHEN MEASURING (1) Do not exceed meter full scale deflection. (2) The test probe must be removed no faster than 1 inch/sec (2.5cm/sec) along the shaded area, otherwise a false reading may result. (3) The test probe must be held with the grip portion of the handle. A false reading may result if the operator’s hand is between the handle and the probe. (4) When testing near a corner of the door, keep the probe perpendicular to the surface being tested. (Hold vertically when testing the top and bottom, and horizontally along the side.) (1) When you replace the magnetron, measure for microwave energy leakage before the outer case is installed and after all necessary components are replaced or adjusted. Special care should be taken in measuring the following parts. - Around the magnetron - The waveguide WARNING: AVOID CONTACTING ANY HIGH VOLTAGE PARTS. MEASUREMENT WITH A FULLY ASSEMBLED OVEN RECORD KEEPING AND NOTIFICATION AFTER MEASUREMENT (1) After all components, including the outer panels, are fully assembled, measure for microwave energy leakage around the door viewing window, the exhaust opening and air inlet openings. (2) Microwave energy leakage must not exceed the values prescribed below. NOTES: Leakage with the outer panels removed less than 5 mW/cm2. Leakage for a fully assembled oven (“Before the latch switch (primary) is interrupted”) with the door in a slightly opened position - less than 2 mW/cm2. (1) After adjustment and repair of any microwave energy interruption or microwave energy blocking device, record the measured values for future reference. Also enter the information on the service invoice. (2) Should the microwave energy leakage not be more than 2 mW/cm2 after determining that all parts are in good condition, functioning properly and genuine replacement parts which are listed in this manual have been used. (3) At least once a year, have the electromagnetic energy leakage monitor checked for calibration by its manufacturer. POWER OUTPUT MEASUREMENT (6) The microwave power output P in watts is calculated from the following formula : (1) Microwave power output measurement is made with the microwave oven supplied at its rated voltage and operated at its maximum microwave power setting with a load of (1000±5) g of potable water. (2) The water is contained in a cylindrical borosilicate glass vessel having a maximum material thickness of 1/8" (3 mm) and an outside diameter of approximately 7.6" (190mm). (3) The oven and the empty vessel are at ambient temperature prior to the start of the test. (4) The initial temperature (T1) of the water is (10±2)°C (50°F) It is measured immediately before the water is added to the vessel. After addition of the water to the vessel, the load is immediately placed on the center of the turntable which is in the lowest position and the microwave power switched on. (5) The time T for the temperature of the water to rise by a value ∆T of (10±2)°K is measured, where T is the time in seconds and ∆T is the temperature rise. The initial and final water temperatures are selected so that the maximum difference between the final water temperature and the ambient temperature is 5°K. P= 4.187Mw(T2 – T1)+0.55Mc(T2 – T0) t is measured while the microwave generator is operating at full power. Magnetron filament heat-up time is not included. (about 3 sec) (7) The water is stirred to equalize temperature throughout the vessel, prior to measuring the final water temperature. (8) Stirring devices and measuring instruments are selected in order to minimize addition or removal of heat. WATER LOAD TURNTABLE 7-3 DISASSEMBLY INSTRUCTIONS (4) Remove 3 screws securing the circuit board. IMPORTANT NOTES: UNIT MUST BE DISCONNECTED FROM ELECTRICAL OUTLET WHEN MAKING REPAIRS, REPLACEMENTS, ADJUSTMENTS AND CONTINUITY CHECKS. WAIT AT LEAST ONE MINUTE, UNTIL THE HIGH VOLTAGE CAPACITOR IN THE HIGH VOLTAGE POWER SUPPLY HAS FULLY DISCHARGED. THE CAPACITOR SHOULD BE DISCHARGED BY USING INSULATED WIRE - I.E. TEST PROBE CONNECTED TO 10K-OHM RESISTOR IN SERIES TO GROUND. WHEN RECONNECTING THE WIRE LEADS TO ANY PART, MAKE SURE THE WIRING CONNECTIONS AND LEAD COLORS ARE CORRECTLY MATCHED ACCORDING TO THE OVERALL CIRCUIT DIAGRAM. (ESPECIALLY SWITCHES AND HIGH VOLTAGE CIRCUIT.) Circuit Board A. REMOVING POWER AND CONTROL CIRCUIT BOARD (Figures 1, 2 and 3) Figure 2 (1) Remove a screw securing the control panel assembly to the oven cavity. (2) Remove the control panel with pushing it upward. (3) Remove the connector (CN1) and wire leads (Relay6) from the circuit board. (5) Remove the FPC connector from the terminal socket following “HOW TO REMOVE THE FPC CONNECTOR” on the next page. (6) Remove the circuit board from the control bracket carefully. Control Panel Screw Control Bracket FPC Connector(S1) Power Transformer Relay 7 Circuit Board (Relay 7) (CN1) Figure 1 Figure 3 7-4 HOW TO REMOVE THE F.P.C. CONNECTOR HOW TO INSERT THE F.P.C. CONNECTOR Follow the steps below as illustrated in Figures 4 and 5 to remove the F.P.C. connector. Follow the steps below as illustrated in Figures 6 and 7 to insert the F.P.C. connector. (1) Insert the F.P.C. connector into the terminal socket securely with the fingers. (2) Hold the plastic fastener with thumb and forefinger of the other hand, and push it slowly into the terminal socket. (Figure 6) NOTE: When reconnecting the F.P.C connector make sure that the holes on the F.P.C. connector are properly engaged with the hooks on the plastic fastener (3) Lock the level of the plastic fastener into the hook of the terminal socket securely by releasing the fingers. (Figure 7) (1) Hold the edges of the plastic fastener with thumb and forefinger. (Figure 4) (2) Lift up the lever of the plastic fastener from the terminal socket by lightly pressing the lever end with forefinger. (Figure 5) (3) Remove the F.P.C. connector from the terminal socket. Plastic fastener Plastic fastener Hook Holes F.P.C. Connector Terminal socket F.P.C. Connector Figure 4 Terminal socket Figure 6 Plastic fastener Hook Plastic fastener Holes F.P.C. Connector F.P.C. Connector Terminal socket Terminal socket Figure 5 Figure 7 7-5 (6) Remove the power cord cover from outcase by removing a screw. (7) Remove the power cord to the inner of the out case with turning power cord and remove the out case with pushing it back. B. REMOVING THE OUT CASE(Figure 8) (1) Remove the vent grille by removing two screws securing it to the out case. (2) Remove two screws securing it to the front bracket. (3) Remove two screws securing it to the air duct. (4) Remove the mounting plate by turning the two screws securing it to the out case. (5) Remove the base plate by removing six screws securing it to the out case. Remove the Mount, All from the out case by removing two screws securing it to the out case and one screw securing it to the ventilation motor ASS'Y and cavity. Mount, All Power code Door Mounting Plate Out Case Vent Grille Controller Figure 8 7-6 C. REMOVING THE DOOR INTERLOCK SWITCHES (Figures 9,10) (1) Disconnect the wire leads from the interlock switches. (2) Remove two screws securing the Latch Board. (3) Make necessary replacements and check microwave energy leakage according to “ADJUSTMENT PROCEDURE” on page 7-12. Latch Board Secondary Interlock Switch Latch Board Secondary Interlock Switch WH(from H.V.Transformer) WH(from Monitor S/W) WH(from Oven Thermostat) WH(from Cooktop lamp Interlock Monitor Switch Primary Interlock Switch Monitor Interlock Switch WH(from Secondary switch) Figure 10 RD(from Ry 7) Primary Interlock Switch WIRE COLOR SYMBOL WH BK BR RD BL PK GY GN(from P.C.B) YL(from P.C.B) Figure 9 7-7 COLOR WHITE BLACK BROWN RED BLUE PINK GREY GN GREEN N.P. Not Provided NOTES: • When removing the magnetron, make sure that its dome does not hit any adjacent parts, or it may be damaged. D. REMOVING MAGNETRON (Figures 11 Through 13) (1) Remove vertgrille. (2) Remove mount all. (3) Remove outcase. (4) Discinnect the wireleads. (5) Remove the 3 screws and Magnetron very carefully. • When replacing the magnetron, be sure to install the magnetron gasket in the correct position and be sure that the gasket is in good condition. • After replacing the magnetron, check for microwave energy leakage with a survey meter Check microwave energy leakage must be below the limit of 5 mW/cm2. (All service adjustments should be made for minimum microwave energy leakage readings.) mount all outcase vertgrille Figure 11 Magnetron Figure 13 7-8 Figure 12 E. REMOVING STIRRER FAN F. REMOVING DOOR (Figure 16) (Figures 14 and 15) (1) Remove one rivet ASS'Y securing it to the oven upper plate by using knife blade. (2) Rotate slightly and pull out the stirrer fan cover. (3) Remove the stirrer fan. (1) Remove the vent grille by two screws securing it to the outcase loosening. (2) Lift up and draw the door. NOTES: • After replacing the door, be sure to check that the primary interlock switch, the secondary interlock switch and the interlock monitor switch is in good operating normally. • After replacing the door, check for microwave energy leakage with a survey meter. Microwave energy leakage must be below the limit of 5mW/cm2 . (With a 275 ml water load) Figure 14 Figure 16 G. DISASSEMBLING DOOR (Figure 17) (1) Remove the dielectric choke by using knife blade or small screw driver, etc. (2) Remove two screws securing it to the door handle. CAUTION: Be careful not to damage door seal plate with the screwdriver. Figure 15 Door Screen Figure 17 7-9 (3) Carefully pull the ventilation motor ASS'Y out of the microwave oven. (See Figure 20) H. ASSEMBLING DOOR (1) When mounting the door assembly to the oven assembly, be sure to adjust the door assembly parallel to the chassis. Also adjust so the door has no play between the inner door surface and oven frame assembly. If the door assembly is not mounted properly, microwaves may leak from the clearance between the door and the oven. Space Figure 20 I. REMOVING THE VENTILATION FAN ASS’Y (1) Remove the mounting plate by removing two screws securing it to the back plate. (See Figure 18) (2) Remove the two screws securing the MOUNT, ALL and one screw securing the ventilation fan ASS'Y. (See Figure 19) Figure 18 MOUNT, ALL Figure 19 7-10 J. REMOVING THE TURNTABLE MOTOR (1) Remove the turntable. (2) Remove the turntable shaft VERY CAREFULLY with a slotted screwdriver. (Figure 21) (3) Remove the base plate by removing 6 screws securing it to the oven cavity. (Figure 22) (4) Disconnect the leadwire from the turntable motor terminals. (5) Remove the 2 screws securing the turntable motor to the oven cavity ASS'Y. (Figure 23) NOTES: • Remove the leadwire from the turntable motor VERY CAREFULLY. • Be sure to grasp the connector not the wires when removing. Figure 21 Figure 22 Wire Leads Turntable Motor Figure 23 7-11 INTERLOCK SYSTEM INTERLOCK MECHANISM The door lock mechanism is a device which has been specially designed to eliminate completely microwave activity when the door is opened during cooking and thus to prevent the danger resulting from the microwave leakage. ADJUSTMENT PROCEDURES To avoid possible exposure to microwave energy leakage, adjust the door latches and interlock switches, using the following procedure. CHECK THE DOOR LATCH AND SWITCH CLOSING. NOTE: The outer cover of the microwave oven is removed. The Interlock Monitor and Primary Interlock Switch act as the final safety switch protecting the user from microwave energy. The terminals between “COM” and “NC” of the Interlock Monitor must close when the door is opened. After adjusting the Interlock Monitor Switch, make sure that it is correctly connected. Mounting of the primary/monitor/secondary switches to the latch board. (1) Set the microwave oven on its side so that you can see the latch board and the switches, as shown in Figure 24. (2) Close the door tightly and check gaps A and B to be sure they are no more than 1/64" (0.5 mm). See Figure 25 for close-up view of gaps A and B (door latches). If all gaps are less than 1/64" (0.5 mm), adjustment of the latch board may not be necessary. Go to Steps 5 and 6 to check the sequence of the switches. Latch Board NOTE: To correct sequence of the Primary Interlock Switch, Secondary Interlock Switch and the Interlock Monitor Switch is very important. If any gap is larger than 1/64" (0.5 mm), you will need to adjust the latch board”. Go to step 3 and follow all steps in order. Secondary Interlock Switch ADJUST THE LATCH AND SWITCH CLOSING (3) Loosen the two screws holding the plastic latch board as shown. Interlock Monitor Switch (4) With the oven door closed tightly, move the latch board upward toward the top of the oven and/or away from the door latch until the gaps are less than 1/64" (0.5 mm). Hold the latch board tightly in this position until you check the sequence of the switches in steps 5 and 6. Primary Interlock Switch Figure 24 LATCH 0-1/64" Figure 25 LATCH BOARD 0-1/64" 7-12 TEST THE LATCH AND SWITCH SEQUENCE (7) When you achieve the proper sequence of switches in Steps 5 and 6, tighten the latch board screws at that point. (5) Open the oven door slowly. Watch the door latch, the Secondary Switch. Release Rod and Lever on the switches to make sure they are zero to the body of the switches in the following sequence: TEST THE MICROWAVE ENERGY LEAKAGE - Primary Interlock Switch - Secondary Interlock Switch - Interlock Monitor Switch Make sure the microwave energy leakage is below the limit of 1mW/cm2 (with a 275 ml water load) and 5mW/cm2 (with a 275 ml water load without the cabinet) when measured with a survey meter. Adjust the latch board until the switches operate in this sequence. See Steps 3 and 4. (6) Close the oven door slowly and be sure it is tightly closed. Watch the three switches to make sure they are zero to the body of the switches in the following sequence: - Interlock Monitor Switch - Primary Interlock Switch - Secondary Interlock Switch NOTE: The Interlock Monitor Switch is an added safety check on the Primary and Secondary Interlock Switches. If the Primary and Secondary Interlock Switches allow the oven to operate with the door open, the Monitor Switch will blow the fuse. 7-13 INTERLOCK CONTINUITY TEST A. PRIMARY INTERLOCK SWITCH TEST B. SECONDARY INTERLOCK SWITCH TEST When the door is opened slowly, an audible click should be heard at the same time or successively at intervals and the latches should activate the switches with an audible click. If the latches do not activate the switches when the door is closed, the switches should be a adjusted in accordance with the adjustment procedure. Disconnect the wire lead from the primary switch. Connect the ohmmeter leads to the common (COM) and normally open (NO) terminal of the switch. The meter should indicate an open circuit in the door open condition. When the door is closed, the meter should indicate a closed circuit. When the primary switch operation is abnormal, make the necessary adjustment or replace the switch only with the same type of switch. COMPONENTS SWITCHES (Wire leads removed) Disconnect the wire lead from the secondary switch. Connect the ohmmeter leads to the common (COM) and normally open (NO) terminals of the switch. The meter should indicate a open circuit in the door open condition. When the door is closed, meter should indicate an closed circuit. When the secondary switch operation is abnormal, make the necessary adjustment or replace the switch only with the same type of switch. C. MONITOR SWITCH TEST Disconnect the wire lead from the monitor switch. Connect the ohmmeter leads to the common (COM) and normally closed (NC) terminals of the switch. The meter should indicate closed circuit in the door open condition. When the door is closed, meter should indicate an open circuit. When the monitor switch operation is abnormal, replace with the same type of switch. NOTE: After repairing the door or the interlock system, it is necessary to do this continuity test before operating the oven. TEST PROCEDURE Check for continuity of the switch with an Ohm-meter Primary Switch Monitor Switch Secondary Switch RESULTS Door open Door closed NO COM NC COM NO COM NOTE: After checking for the continuity of switches, make sure that they are connected correctly. WARNING : FOR CONTINUED PROTECTION AGAINST EXCESSIVE RADIATION EMISSION, REPLACE ONLY WITH IDENTICAL REPLACEMENT PARTS. TYPE NO. SZM-V16-FA-63 OR VP-533A-OF OR V-5230Q FOR PRIMARY SWITCH TYPE NO. SZM-V16-FA-62 OR VP-532A-OF OR V-5220Q FOR MONITOR SWITCH TYPE NO. SZM-V16-FA-63 OR VP-533A-OF OR V-5230Q FOR SECONDARY SWITCH 7-14 TEST AND CHECKOUT PROCEDURES, AND TROUBLE SHOOTING - CAUTIONS Filament Winding - DISCONNECT THE POWER SUPPLY CORD FROM THE WALL OUTLET WHENEVER REMOVINGING THE CABINET FROM THE UNIT. PROCEED WITH THE TESTS ONLY AFTER DISCHARGING THE HIGH VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE HIGH VOLTAGE TRANSFORMER. (SEE FIGURE 26) Secondary Winding - ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER OF WATER IN CONTAINER) IN THE OVEN. Primary Winding Figure 26 A. TEST PROCEDURES COMPONENTS TEST PROCEDURES 1) Measure the resistance: Across the filament terminals of the magnetron with an ohm-meter on Rx1 scale. MAGNETRON (Wire leads are removed) HIGH-VOLTAGE TRANSFORMER (Wire leads are removed) 2) Measure the resistance: Between each filament terminal of the magnetron and the chassis ground with an ohm-meter on high test scale. RESULTS Normal reading: Less than 1 ohm. Normal reading: Infinite ohms. NOTE: Replace the magnetron, if the magnetron checks and all of the high voltage component tests are good, but the unit still does not heat a load. 1) Measure the resistance: With an ohm-meter on Rx1 scale. a. Primary winding; b. Filament winding; c. Secondary winding; Normal readings: Approx. 0.3 to 0.5 ohm. Less than 0.1 ohm. Approx. 65 to 120 ohms. 2) Measure the resistance: With an ohm-meter on highest scale. a. Primary winding to ground; b. Filament winding to ground; Normal readings: Infinite ohms. Infinite ohms. NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. 7-15 COMPONENTS TEST PROCEDURES Measure the resistance: (1) Terminal to terminal RESULTS Normal reading: Momentarily indicates several ohms, and then gradually returns to infinite ohms. Ohmmeter Abnormal reading: Indicates continuity or infinite ohms from the beginning. Figure 27-a HIGH-VOLTAGE CAPACITOR (2) Terminal to case Normal readings: Infinite. Abnormal reading: Indicates continuity. Ohmmeter Figure 27-b Normal readings: continuity. Measure the continuity: (1) Forward Abnormal reading: Infinite. Ohmmeter Figure 28-a HIGH-VOLTAGE DIODE (1) Reverse Normal readings: Infinite. Ohmmeter Abnormal reading: continuity. Figure 28-b 7-16 COMPONENTS TEST PROCEDURES RESULTS Measure the resistance between terminal pins of connector KEY CONNECTOR. NOTE: When reconnecting the FPC connector, make sure that the holes on the FPC connector are properly engaged with hooks on the plastic fastener. MATRIX CIRCUIT FOR TOUCH KEY BOARD Resistance value When touched When not touched Less than More than 400 ohms 1 mega ohm FPC CONNECTOR Top CONNECTOR(KEY CON) (For detail matrix circuit of each model, refer to page 5-2.) 1 2 3 4 5 6 7 8 9 10 11 12 13 TOUCH KEY BOARD Figure 30 Figure 29 Normal: Approximately BK~RD: 4.5~6.2 Kohm RD~WH: 2.0~3.5 Kohm BK~WH: 2.0~3.5 Kohm Abnormal: Infinite or several. SENSOR (For sensor model only) 1 2 3 BK RD WH Figure 31 7-17 COMPONENTS TEST PROCEDURES RESULTS Check for continuity of relay 2 with an ohm-meter. (Remove wire leads from relay 2 and operate the unit.) Relay 2 RELAY2 POWER LEVEL 1 4 sec 18 sec 2 6 sec 16 sec 3 8 sec 14 sec 4 10 sec 12 sec 5 12 sec 10 sec 6 14 sec 8 sec 7 16 sec 6 sec 8 18 sec 4 sec 9 20 sec 2 sec 10 22 sec 0 Figure 32 CAUTION: The relay connector 2(White) and 5(Red) must be correctly connected Relay 6. These two connectors are not Interchangeable. NOTES: • A MICROWAVE ENERGY TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. • MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION. • WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT THE WIRES. B. CHECKOUT PROCEDURES (1) CHECKOUT PROCEDURES FOR FUSE BLOWING CAUTION: REPLACE BLOWN FUSE WITH 20 AMPERE FUSE. PROBLEMS CAUSES Fuse blows immediately after the door is closed. Improper operation of the primary interlock, secondary interlock switches and/or the interlock monitor switch. Fuse blows immediately after the door is opened. Malfunction of the high voltage transformer; the high voltage capacitor including the diode, the magnetron, the blower motor or the circuit board. Fuse blows when the door is closed and START key is touched. NOTES: • If the fuse is blown by an improper switch operation, replace the all Interlock switches, PCB Ass’y and the fuse at the same time. After replacing the the all Interlock switches, PCB Ass’y, Fuse with new ones, make sure that they are correctly connected. • Check for microwave energy leakage according to INTERLOCK ADJUSTMENT PROCEDURES on page 7- 12 when the primary interlock, secondary interlock switches and/or the interlock monitor switches are adjusted or replaced. 7-18 (2) CHECKOUT PROCEDURES FOR RELAY. - PROBLEM (A) T.T. motor and oven lamp turn on without touching START key when the door is closed. NO GOOD YES Remove the mate connector of I/O CON from the circuit board. Does the unit still operate? NO Replace the circuit board YES Defective RELAY3 Replace RELAY3 - PROBLEM (B) T.T. motor and oven lamp turn on When the door is closed and START key is touched. YES GOOD NO Measure the voltage at pin NO. 4 of U01 Voltage reading: 0 Vdc NO Replace the circuit board YES Defective RELAY3 or poor connection of RELAY3 Replace RELAY3 or correct the connection. 7-19 (3) CHECKOUT PROCEDURES FOR CIRCUIT BOARD The following symptoms indicate a defective circuit board. 1) The start function fails to operate but the high voltage Systems, the interlock switches, the door sensing and the relay check good. 2) The unit with a normal relay continuously operates. 3) Proper temperature measurement is not obtained. 4) The buzzer does not sound or continues to sound. 5) Some segments of one or more digits do not light up, or they continue to light up, or segments light when they should not. 6) Wrong figures appear. 7) The figures of all digits. 8) Some of the indicators do no flicker light up. 9) The clock does not keep time properly. NOTE: A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. 7-20 7-21 Measure voltage between pin 1 and pin 3 of connector CN1. WH RD 1 Measure resistance of touch key board after removing connector S1. (See page 7-4 and 7-17) 120 Resistance incorrect Normal resistance Voltage incorrect 0 120 120V 0 Correct connections Replace circuit board Replace touch key board. Check contact of connector S1 Check: 1. POWER SUPPLY 2. FUSE (See “CHECKOUT PROCEDURES FOR FUSE BLOWING: on page 7- 18) 3. OVEN CAVITY THERMOSTAT PROBLEM - B: Display does not show correct numbers and/ or correct indications when programmed. 1 PROBLEM - A: “PLEASE SET TIME OF DAY” does not appear in display window when power supply cord is plugged into wall outlet. C. TROUBLE SHOOTING Before following this troubleshooting read “TRIAL OPERATION” on page 6- 1. • “DISPLAY” Problems, “A” thru “C” • “HELP UP” Problems, “D” thru “E” • “BUZZER Problems, “F” Normal touch key board Poor contact Contact ok Normal resistance Normal circuit board Correct seating Replace circuit board Normal contact Normal circuit board Runs Runs Runs Runs Runs 7-22 2 1 Measure resistance of H.V.Transformer (see page 7-15) Check the contact of relay 6(see page 7-18) Normal resistance Resistance incorrect Contact OK NO continuity Check: 1. PRIMARY AND SECONDARY INTERLOCK SWITCHES 2 . THERMOSTAT PROBLEM - C: Unit does not heat up even if display counts down when START key is touched for "HIGH POWER" cooking. Replace H.V.T. Normal H.V.T. Normal circuit board Check the continuity of H.V.C. (see page 7-16) Check contact of connector S1 Replace circuit board Normal resistance Resistance incorrect Contact OK Poor contact Check the continuity of H.V.D. (see page 7-16) Replace circuit board Correct seating Normal H.V.D. Normal Magnetron Replace H.V.D. Replace Magnetron Normal Normal H.V.C. Abnormal Replace H.V.C. Normal circuit board Normal contact Runs Runs Runs 7-23 1 Check normal operation circuit board PROBLEM - D: No buzzing when touching the key, between stages or at end of cooking Replace circuit board Normal circuit board Runs 7-24 1 Check the contact of oven thermostat Check: 1. POWER SUPPLY 2. FUSE Contact OK NO contact Check contact of connector S1 (see page 7-4) Replace oven thermostat PROBLEM - G: Ventilation fan does not operate when “FAN HIGH/ LOW” key is touched. Contact OK Poor contact Replace circuit board Correct seating Normal circuit board Normal contact NO runs Replace ventilation motor ASS Y Normal ventilation motor Runs Runs Runs Runs #EV# EXPLODED VIEW DOOR PARTS 13581A 13552A 13536A For Model 13551A 767.85413 13213A 13720D WTT028 14026A 14760A 14890A 14970A 13650A 8-1 #EV# CONTROLLER PARTS For Model: 767.85410 767.85419 24781M 268711 23551A 24810P WTP018 23572A *07 23506A For Model: 767.85413 24781M 268711 23551A 24810P WTP018 *07 8-2 #EV# OVEN CAVITY PARTS WTT021 34960A WTT028 WTT027 WTT029 For Model 767.85419 WTT027 767.85413 33530A For Model WTT029 767.85410 34810Q 33112U 34930R *01 *02 *05 *04 35026G 368771 33550L 63302A 36912C 34890C 34810T WTT010 WTT022 WTT022 35230A 8-3 63303A #EV# LATCH BOARD PARTS 43500A 466001 WSZ085 43501A 466003 466001 44510A 8-4 #EV# INTERIOR PARTS(I) WSZ002 33390G 56324A 34370T 56201B 35889A WTT021 WTT021 56170D 33740A WTP015 33052A WTT021 36549S WTP013 WSZ002 53300A 56851D WSZ002 54810C 50CZZH 53300B 8-5 #EV# INTERIOR PARTS(II) 56912B 55231C 53550L 36549V WSZ002 56804A 56201A WTT028 56411A 55262A 50FZZA 56930V 568771 WSZ002 55892A 54930F 53550F 340511 8-6 #EV# INSTALLATION PARTS 63300M 65862D 65862B 63861A VINYL BAG 8-7 REPLACEMENT PARTS LIST For Model: 767.85410 I/C : INTERCHANGEBILITY CODE Location No. Part Name *01 *02 *04 *05 *06 *07 *10 13213A 13536A 13552A 13581A 13650A 13720D 14026A 14760A 14890A 14970A 23506A 23551A 23572A 24781M 24810P 268711 33052A 33112U 33390G 33530A 33550L 33740A 340511 34370T 34810Q 34810T 34890C 34930R 34960A 35026G 35230A 35230A 35889A 36549S 36549V 368771 36912C 43500A 43501A 44510A 466001 466001 MANUAL,OWNERS MANUAL,SERVICE MANUAL,INSTALLATION LABEL,COOKING GUIDE TEMPLATE CARD,TECHNICAL BOX,YELLOW DOOR FRAME ASSEMBLY SEAL TAPE CHOKE COVER DOOR ASSEMBLY HANDLE,DOOR PANEL,DOOR LATCH BAFFLE GLASS SPRING KEY MEMBRANE SERVICE PARTS(CONTROL PANEL+KEY PAD) PANEL,CONTROL CONTROLLER ASSEMBLY,MICOM BRACKET,CONTROL PANEL PWB(PCB) ASSEMBLY,SUB CANOPY,RESIN OUT CASE,U-BENDING TRAY,GLASS GRILLE,VENT COVER,LAMP PROTECTOR (MECH) RIVET ASSEMBLY SHAFT,TURN TABLE BRACKET,MOUNT BRACKET,LAMP GLASS HOLDER,COOK AUXILIARY MOUNT SHELF FILTER(MECH),GREASE FILTER(MECH),GREASE ROTATING RING ASSEMBLY MOTOR(CIRC),SYNCHRONOUS MOTOR(CIRC),VENTILATION HARNESS LAMP,DRAWING BOARD,LATCH BOARD ASSEMBLY,LATCH LEVER SWITCH,MICRO SWITCH,MICRO Difference Chart (Part No) 767.8541000 I/C 767.8541001 3828W5A4048 3828W5S3674 3828W5U0348 3850W2A233D 4922W5A027A 3840W1T004C 3890W3Y819H 3213W1A035C 3536WRA001R 3552W1A032B 3581W1A352A 3650W1A075A 3720W0D259A 4026W2A015A 4890W1A021X 4970WRA001E 4760W0A002A 3506W1A600A → → → → → → → → → → → → → → → → → 3828W5A8142 3828W5S5159 3828W5U0438 3850W2A233G 4922W1A021C 3840W1T004F 3890W3Y927B 3213W1A049G 3536W1A012B 3552W1A032E 3581W1A352H 3650W1A075E 3720W0D259D 4026W2A019A 4760W0A002D 4890W1A066C 4970WRA001G 3506W1A600A 383EW5A204E 3720W0C058D 4781W1M307U 4810W1G061E 6871W1S106F 3052W1A002A 3112W0U052H 1B71961H 3530W0A030E 3550W3A095C 3740W1A005E 4051W3A001A 4370W1A006B 4810W1A149A 4810W1A150C 4890W1A045A 4930W1A069A 4960W1A021B 5026W1A048C 5230W1A012A 5230W1A012A 5889W2A012F 6549W1S011M 6549W1V006F 6877W1A002A 6912W1Z004B 3500W1A028B 3501W1A019D 4510W3A012C 6600W1K001D 6600W1K001D 3720W0C058A 4781W1M307G 4810W1G061B 6871W1S106D 3052WRA002A 3112W1U026H 1B71961E 3530W0A030A 3550W3A095A 3740W1A005A 4051W3A001A 3B72373A 4810W3G062A 4810W3G100A 4890W4A001G 4890W4A001G 4930W1A026A 4960W1A004B 5026W1A048C 2B72705B 5889W2A012D 6549W1S013C 6549W1V006F 6877W1A340A 6912W3Q001A 3500W1A013A 3501W1A019C 4510W4A005A 3B73362F 3B73362F 8-8 → → → → → → → → → → → → → → → → → → → → → → → → → → → → → Mar. 29. 2005 SVC R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R Alternate 3650W1A075A 3720W0D259A 4760W0A002A 4890W1A054D 4810W1G061B 3550W3A095A 3740W1A005A 4890W4A001G 2B72705C 5230W1A012B 6549W1S015C 6600W1K004C 6600W1K003D Location No. 466003 466003 50CZZH 50CZZH 50CZZH 50FZZA 53300A 53300B 53550F 53550L 54810C 54930F 55231C 55262A 55892A 56170D 56201A 56201B 56324A 56411A 56804A 56851D 56851D 568771 56912B 56930V 63300M 63302A 63303A 63861A 65862B 65862D WSZ002 WSZ085 WTP013 WTP015 WTP018 WTT010 WTT021 WTT022 WTT028 WTT029 Difference Chart (Part No) Part Name SWITCH,MICRO SWITCH,MICRO CAPACITOR,DRAWING[HIGH VOLTAGE] CAPACITOR,DRAWING[HIGH VOLTAGE] CAPACITOR,DRAWING[HIGH VOLTAGE] FUSE,DRAWING PLATE,BOTTOM PLATE,BOTTOM COVER,STIRRER FAN COVER,LAMP BRACKET,CAPACITOR HOLDER,STIRRER FAN FILTER(MECH),CHARCOAL DUCT FAN TRANSFORMER,HIGH VOLTAGE FILTER ASSEMBLY(CIRC) FILTER ASSEMBLY(CIRC) MAGNETRON POWER CORD ASSEMBLY SOCKET(CIRC),LAMP CABLE ASSEMBLY CABLE ASSEMBLY HARNESS LAMP,DRAWING THERMOSTAT PLATE,MOUNTING BASE PLATE BASE PLATE ASSEMBLY KIT ASSEMBLY BRACKET,MISC DAMPER SCREW TAP TITE(S),BINDING HEAD SCREW,DRAWING SCREW TAPPING,PAN HEAD SCREW TAPPING,PAN HEAD SCREW TAPPING,PAN HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD 8-9 767.8541000 I/C 767.8541001 3B73361E 3B73361E 0CZZW1H004B 0CZZW1H004B 0CZZW1H004B 3B74133K 3300W1A052A 3300W1A003A 3550W1A126A 3550W3A082A 4810W3C002A 4930W3A013A 2B72706D 5208W0A006A 5892W1A003A 6170W1D052B 2B72130F 2B71165P 6411W1A010L 6201W2A019D 6804W3A001A 6021W3B001A 6021W3B001A 6877W1A409C 3B70067A 6930W1A003E 3300W0M003A 3302W0A013H 3303W1A041N 2B72771A 3B72144A 3B71432A 1SBF0402418 4B70188B 1TPL0402418 1TPL0402618 1TPL0402818 1TTG0402422 1TTL0402418 1TTL0402422 1TTL0402818 1TTL0402822 → → 6600W1K001C 6600W1K001C 0CZZW1H004B 0CZZW1H004B 0CZZW1H004B 3B74133Q 3300W1A052B 3300W1A003D 3550W1A126B 3550W1A189A 4810W1A141A 4930W1A068A 5230W1A011A 5208W0A006B 5892W1A003A 6170W1D052B 2B72130F 6201W2A019D 2B71165R 6411W1A010Z 6804W3A001A 6021W3B001V 6021W3B001V 6877W1A004B 6912W1Z004A 6930W1A003E 3300W0A018A 3302W0A047A 3303W1A072G 3861W1A043A 4810W1A151A 4900W1A001B 1SBF0402418 4B70188C 1TPL0402418 1TPL0402618 1TPL0402818 1TTG0402422 1TTL0402418 1TTL0402422 1TTL0402818 1TTL0402822 → → → → → → → → → → → → → → → → → → → → → → → SVC Alternate R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 6600W1K003C 6600W1K004B 0CZZW1H004G 0CZZW1H002H 0CZZW1H001Q 3B74133K 3300W1A052A 3300W1A003A 3550W1A126A 5230W1A011B 6021W3B001G 6851W1A002B 6930W3A001S REPLACEMENT PARTS LIST For Model: 767.85413 Location No. *01 *02 *04 *05 *06 *07 *10 13213A 13536A 13551A 13552A 13581A 13650A 14026A 14760A 14890A 14970A 23551A 24781M 24810P 268711 33052A 33112U 33390G 33530A 33550L 33740A 340511 34370T 34810Q 34810T 34890C 34930R 34960A 35026G 35230A 35230A 35889A 36549S 36549V 368771 36912C 43500A 43501A 44510A 466001 466001 466003 466003 I/C : INTERCHANGEBILITY CODE Difference Chart (Part No) Part Name MANUAL,OWNERS MANUAL,SERVICE MANUAL,INSTALLATION LABEL,COOKING GUIDE TEMPLATE CARD,TECHNICAL BOX,YELLOW DOOR FRAME ASSEMBLY SEAL TAPE SERVICE PARTS(DOOR PANEL+GLASS+COVER) CHOKE COVER DOOR ASSEMBLY HANDLE,DOOR LATCH BAFFLE GLASS SPRING CONTROLLER ASSEMBLY,SUB CONTROLLER ASSEMBLY,MICOM BRACKET,CONTROL PANEL PWB(PCB) ASSEMBLY,SUB CANOPY,RESIN OUT CASE,U-BENDING TRAY,GLASS GRILLE,VENT COVER,LAMP PROTECTOR (MECH) RIVET ASSEMBLY SHAFT,TURN TABLE BRACKET,MOUNT BRACKET,LAMP GLASS HOLDER,COOK AUXILIARY MOUNT SHELF FILTER(MECH),GREASE FILTER(MECH),GREASE ROTATING RING ASSEMBLY MOTOR(CIRC),SYNCHRONOUS MOTOR(CIRC),VENTILATION HARNESS LAMP,DRAWING BOARD,LATCH BOARD ASSEMBLY,LATCH LEVER SWITCH,MICRO SWITCH,MICRO SWITCH,MICRO SWITCH,MICRO 767.8541300 I/C 767.8541301 3828W5A4048 3828W5S3674 3828W5U0348 3850W2A233D 4922W5A027A 3840W1T004C 3890W3Y819J 3213W1A035D 3536WRA001R 383EW5A204A 3552W1A032B 3581W1A355A 3650W1A075D 4026W2A015A 4760W0A002B 4890W1A021Y 4970WRA001E 383EW5A205A 4781W1M311B 4810W1G061B 6871W1S106D 3052WRA002A 3112W1U026J 1B71961E 3530W0A030D 3550W3A095A 3740W1A005A 4051W3A001A 3B72373A 4810W3G062A 4810W3G100A 4890W4A001G 4930W1A026A 4960W1A004B 5026W1A048C 2B72705B 2B72705B 5889W2A012D 6549W1S013C 6549W1V006F 6877W1A340A 6912W3Q001A 3500W1A013A 3501W1A019C 4510W4A005A 3B73362F 3B73362F 3B73361E 3B73361E → → → → → → → → → → → → → → → → → → → → → → → → → → → 3828W5A8142 3828W5S5159 3828W5U0438 3850W2A233G 4922W1A021C 3840W1T004F 3890W3Y927C 3213W1A049F 3536W1A012B 383EW5A204C 3552W1A032E 3581W1A355E 3650W1A075H 4026W2A019C 4760W0A002E 4890W1A066D 4970WRA001G 4781W1A299B 4781W1M311F 4810W1G061E 6871W1S106F 3052W1A002A 3112W0U052J 1B71961H 3530W0A030H 3550W3A095C 3740W1A005E 4051W3A001A 4370W1A006B 4810W1A149A 4810W1A150C 4890W1A045A 4930W1A069A 4960W1A021B 5026W1A048C 5230W1A012A 5230W1A012A 5889W2A012F 6549W1S011M 6549W1V006F 6877W1A002A 6912W1Z004B 3500W1A028B 3501W1A019D 4510W3A012C 6600W1K001D 6600W1K001D 6600W1K001C 6600W1K001C 8-10 → → → → → → → → → → → → → → → → → → → Mar. 29. 2005 SVC R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R Alternate 3650W1A075D 4760W0A002B 4890W1A054E 4810W1G061B 3550W3A095A 3740W1A005A 4890W4A001G 2B72705C 5230W1A012B 6549W1S015C 6600W1K004C 6600W1K003D 6600W1K003C 6600W1K004B Location No. 50CZZH 50CZZH 50CZZH 50FZZA 53300A 53300B 53550F 53550L 54810C 54930F 55231C 55262A 55892A 56170D 56201A 56201B 56324A 56411A 56804A 56851D 56851D 568771 56912B 56930V 63300M 63302A 63303A 63861A 65862B 65862D WSZ002 WSZ085 WTP013 WTP015 WTP018 WTT010 WTT021 WTT022 WTT027 WTT028 Difference Chart (Part No) Part Name 767.8541300 CAPACITOR,DRAWING[HIGH VOLTAGE] CAPACITOR,DRAWING[HIGH VOLTAGE] CAPACITOR,DRAWING[HIGH VOLTAGE] FUSE,DRAWING PLATE,BOTTOM PLATE,BOTTOM COVER,STIRRER FAN COVER,LAMP BRACKET,CAPACITOR HOLDER,STIRRER FAN FILTER(MECH),CHARCOAL DUCT FAN TRANSFORMER,HIGH VOLTAGE FILTER ASSEMBLY(CIRC) FILTER ASSEMBLY(CIRC) MAGNETRON POWER CORD ASSEMBLY SOCKET(CIRC),LAMP CABLE ASSEMBLY CABLE ASSEMBLY HARNESS LAMP,DRAWING THERMOSTAT PLATE,MOUNTING BASE PLATE BASE PLATE ASSEMBLY KIT ASSEMBLY BRACKET,MISC DAMPER SCREW TAP TITE(S),BINDING HEAD SCREW,DRAWING SCREW TAPPING,PAN HEAD SCREW TAPPING,PAN HEAD SCREW TAPPING,PAN HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD 0CZZW1H004B 0CZZW1H004B 0CZZW1H004B 3B74133K 3300W1A052A 3300W1A003A 3550W1A126A 3550W3A082A 4810W3C002A 4930W3A013A 2B72706D 5208W0A006A 5892W1A003A 6170W1D052B 2B72130F 6201W2A019D 2B71165P 6411W1A010L 6804W3A001A 6804W3A001A 6021W3B001A 6877W1A409C 3B70067A 6930W1A003E 3300W0M003A 3302W0A013H 3303W1A041N 2B72771A 3B72144A 3B71432A 1SBF0402418 4B70188B 1TPL0402418 1TPL0402618 1TPL0402818 1TTG0402422 1TTL0402418 1TTL0402422 1TTL0402816 1TTL0402818 8-11 I/C → → → → → → → → → → → → → → → → → → → → → → SVC Alternate R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 0CZZW1H004G 0CZZW1H002H 0CZZW1H001Q 3B74133K 3300W1A052A 3300W1A003A 3550W1A126A 767.8541301 0CZZW1H004B 0CZZW1H004B 0CZZW1H004B 3B74133Q 3300W1A052B 3300W1A003D 3550W1A126B 3550W1A189A 4810W1A141A 4930W1A068A 5230W1A011A 5208W0A006B 5892W1A003A 6170W1D052B 2B72130F 6201W2A019D 2B71165R 6411W1A010Z 6804W3A001A 6021W3B001V 6021W3B001V 6877W1A004B 6912W1Z004A 6930W1A003E 3300W0A018A 3302W0A047A 3303W1A072G 3861W1A043A 4810W1A151A 4900W1A001B 1SBF0402418 4B70188C 1TPL0402418 1TPL0402618 1TPL0402818 1TTG0402422 1TTL0402418 1TTL0402422 1TTL0402816 1TTL0402818 5230W1A011B 6021W3B001G 6851W1A002B 6930W3A001S REPLACEMENT PARTS LIST For Model: 767.85419 I/C : INTERCHANGEBILITY CODE Location No. Part Name *01 *02 *04 *05 *06 *07 *10 13213A 13536A 13552A 13581A 13650A 13720D 14026A 14760A 14890A 14970A 23506A 23551A 23572A 24781M 24810P 268711 33052A 33112U 33390G 33530A 33550L 33740A 340511 34370T 34810Q 34810T 34890C 34930R 34960A 35026G 35230A 35230A 35889A 36549S 36549V 368771 36912C 43500A 43501A 44510A 466001 466001 MANUAL,OWNERS MANUAL,SERVICE MANUAL,INSTALLATION LABEL,COOKING GUIDE TEMPLATE CARD,TECHNICAL BOX,YELLOW DOOR FRAME ASSEMBLY SEAL TAPE CHOKE COVER DOOR ASSEMBLY HANDLE,DOOR PANEL,DOOR LATCH BAFFLE GLASS SPRING KEY MEMBRANE SERVICE PARTS(CONTROL PANEL+KEY PAD) PANEL,CONTROL CONTROLLER ASSEMBLY,MICOM BRACKET,CONTROL PANEL PWB(PCB) ASSEMBLY,SUB CANOPY,RESIN OUT CASE,U-BENDING TRAY,GLASS GRILLE,VENT COVER,LAMP PROTECTOR (MECH) RIVET ASSEMBLY SHAFT,TURN TABLE BRACKET,MOUNT BRACKET,LAMP GLASS HOLDER,COOK AUXILIARY MOUNT SHELF FILTER(MECH),GREASE FILTER(MECH),GREASE ROTATING RING ASSEMBLY MOTOR(CIRC),SYNCHRONOUS MOTOR(CIRC),VENTILATION HARNESS LAMP,DRAWING BOARD,LATCH BOARD ASSEMBLY,LATCH LEVER SWITCH,MICRO SWITCH,MICRO Difference Chart (Part No) 767.8541900 I/C 767.8541901 3828W5A4048 3828W5S3674 3828W5U0348 3850W2A233D 4922W5A027A 3840W1T004C 3890W3Y819G 3213W1A035D 3536WRA001R 3552W1A032B 3581W1A352B 3650W1A075B 3720W0D259B 4026W2A015A 4760W0A002B 4890W1A021Y 4970WRA001E 3506W1A600B → → → → → → → → → → → → → → → → → 3828W5A8142 3828W5S5159 3828W5U0438 3850W2A233G 4922W1A021C 3840W1T004F 3890W3Y927A 3213W1A049F 3536W1A012B 3552W1A032E 3581W1A352J 3650W1A075F 3720W0D259E 4026W2A019A 4760W0A002E 4890W1A066D 4970WRA001G 3506W1A600B 383EW5A204D 3720W0C058E 4781W1M307V 4810W1G061E 6871W1S106F 3052W1A002A 3112W0U052J 1B71961H 3530W0A030F 3550W3A095C 3740W1A005E 4051W3A001A 4370W1A006B 4810W1A149A 4810W1A150C 4890W1A045A 4930W1A069A 4960W1A021B 5026W1A048C 5230W1A012A 5230W1A012A 5889W2A012F 6549W1S011M 6549W1V006F 6877W1A002A 6912W1Z004B 3500W1A028B 3501W1A019D 4510W3A012C 6600W1K001D 6600W1K001D 3720W0C058B 4781W1M307H 4810W1G061B 6871W1S106D 3052WRA002A 3112W1U026J 1B71961E 3530W0A030B 3550W3A095A 3740W1A005A 4051W3A001A 3B72373A 4810W3G062A 4810W3G100A 4890W4A001G 4930W1A026A 4960W1A004B 5026W1A048C 2B72705B 2B72705B 5889W2A012D 6549W1S013C 6549W1V006F 6877W1A340A 6912W3Q001A 3500W1A013A 3501W1A019C 4510W4A005A 3B73362F 3B73362F 8-12 → → → → → → → → → → → → → → → → → → → → → → → → → → → → Mar. 29. 2005 SVC R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R Alternate 4890W1A054E 4810W1G061B 3530W0A030B 3550W3A095A 3740W1A005A 4890W4A001G 2B72705C 5230W1A012B 6549W1S015C 6600W1K004C 6600W1K003D Location No. 466003 466003 50CZZH 50CZZH 50CZZH 50FZZA 53300A 53300B 53550F 53550L 54810C 54930F 55231C 55262A 55892A 56170D 56201A 56201B 56324A 56411A 56804A 56851D 56851D 568771 56912B 56930V 63300M 63302A 63303A 63861A 65862B 65862D WSZ002 WSZ085 WTP013 WTP015 WTP018 WTT010 WTT021 WTT022 WTT027 WTT028 Difference Chart (Part No) Part Name SWITCH,MICRO SWITCH,MICRO CAPACITOR,DRAWING[HIGH VOLTAGE] CAPACITOR,DRAWING[HIGH VOLTAGE] CAPACITOR,DRAWING[HIGH VOLTAGE] FUSE,DRAWING PLATE,BOTTOM PLATE,BOTTOM COVER,STIRRER FAN COVER,LAMP BRACKET,CAPACITOR HOLDER,STIRRER FAN FILTER(MECH),CHARCOAL DUCT FAN TRANSFORMER,HIGH VOLTAGE FILTER ASSEMBLY(CIRC) FILTER ASSEMBLY(CIRC) MAGNETRON POWER CORD ASSEMBLY SOCKET(CIRC),LAMP CABLE ASSEMBLY CABLE ASSEMBLY HARNESS LAMP,DRAWING THERMOSTAT PLATE,MOUNTING BASE PLATE BASE PLATE ASSEMBLY KIT ASSEMBLY BRACKET,MISC DAMPER SCREW TAP TITE(S),BINDING HEAD SCREW,DRAWING SCREW TAPPING,PAN HEAD SCREW TAPPING,PAN HEAD SCREW TAPPING,PAN HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD SCREW TAPPING,TRUSS HEAD 767.8541900 I/C 767.8541901 3B73361E 3B73361E 0CZZW1H004B 0CZZW1H004B 0CZZW1H004B 3B74133K 3300W1A052A 3300W1A003A 3550W1A126A 3550W3A082A 4810W3C002A 4930W3A013A 2B72706D 5208W0A006A 5892W1A003A 6170W1D052B 2B72130F 6201W2A019D 2B71165P 6411W1A010L 6804W3A001A 6021W3B001A 6021W3B001A 6877W1A409C 3B70067A 6930W1A003E 3300W0M003A 3302W0A013H 3303W1A041N 2B72771A 3B72144A 3B71432A 1SBF0402418 4B70188B 1TPL0402418 1TPL0402618 1TPL0402818 1TTG0402422 1TTL0402418 1TTL0402422 1TTL0402816 1TTL0402818 → → 6600W1K001C 6600W1K001C 0CZZW1H004B 0CZZW1H004B 0CZZW1H004B 3B74133Q 3300W1A052B 3300W1A003D 3550W1A126B 3550W1A189A 4810W1A141A 4930W1A068A 5230W1A011A 5208W0A006B 5892W1A003A 6170W1D052B 2B72130F 6201W2A019D 2B71165R 6411W1A010Z 6804W3A001A 6021W3B001V 6021W3B001V 6877W1A004B 6912W1Z004A 6930W1A003E 3300W0A018A 3302W0A047A 3303W1A072G 3861W1A043A 4810W1A151A 4900W1A001B 1SBF0402418 4B70188C 1TPL0402418 1TPL0402618 1TPL0402818 1TTG0402422 1TTL0402418 1TTL0402422 1TTL0402816 1TTL0402818 8-13 → → → → → → → → → → → → → → → → → → → → → → SVC Alternate R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 6600W1K003C 6600W1K004B 0CZZW1H004G 0CZZW1H002H 0CZZW1H001Q 3B74133K 3300W1A052A 3300W1A003A 3550W1A126A 5230W1A011B 6021W3B001G 6851W1A002B 6930W3A001S P/NO : 3828W5S5159 Printed in Korea