Download Qlogic SANbox 6142 User`s guide

SANbox 6142
Intelligent Storage Router
User’s Guide
FI0054601-00 C
S
SANbox 6142 Intelligent Storage Router
User’s Guide
Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no
responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its
use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications
described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no
representation nor warranty that such applications are suitable for the specified use without further testing or
modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
This SANbox switch is covered by one or more of the following patents – 6697359; other patents pending.
QLogic and SANbox are trademarks or registered trademarks of QLogic Corporation.
AMCC is a registered trademark of Applied Micro Circuits Corporation
Brocade is a registered trademark of Brocade Communications Systems, Inc.
Cisco is a registered trademark of Cisco Technology, Inc.
Gnome is a trademark of the GNOME Foundation Corporation.
Java and Solaris are registered trademarks of Sun Microsystems, Inc.
Pentium is a registered trademark of Intel Corporation.
IBM and PowerPC are registered trademarks of the International Business Machines Corporation.
Linux is a registered trademark of Linus Torvalds.
MacOS X and Safari are registered trademarks of Apple Computer, Inc.
McDATA is a registered trademark of McDATA Corporation.
Microsoft, Windows XP, Windows 2003, and Internet Explorer are registered trademarks of Microsoft
Corporation.
Netscape Navigator and Mozilla are trademarks or registered trademarks of Netscape Communications
Corporation.
Red Hat is a registered trademark of Red Hat Software Inc.
SANmark is a trademark of the Fibre Channel Industry Association.
SUSE is a trademark of Novell, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Document Revision History
Revision B
Changes
Sections Affected
Edited and updated format to new QLogic style
03/08
Entire Book
Updated illustrations of SANbox 6142 router box
Sections 2 and 5
Corrected information about Heartbeat vs System
Fault LEDs
Section 2
Clarified instructions for pressing the maintenance
button
Section 2
© 2008 QLogic Corporation. All Rights Reserved Worldwide.
Published: Month Year
QLogic Corporation, 26650 Aliso Viejo Parkway, Aliso Viejo, CA 92656, (800) 662-4471 or (949) 389-6000
Page ii
FI0054601-00 C
S
SANbox 6142 Intelligent Storage Router
User’s Guide
Removed reference to SANsurfer application
installation from a CD; replaced CD installation
procedures with steps for downloading software
from the QLogic website
Section 4
Corrected information about when the Configuration Wizard launches automatically
Section 4
Corrected information on LED diagnostics to identify the blink patterns that display on the System
Fault LED, not the Heartbeat LED
Section 5
Updated screens and descriptions regarding IP
addresses to include IPv6 options in SANsurfer
iSCSI/FC Router Manager
Section 7
Added traceroutes command and replaced
screen samples to show IPv6 support
Appendix A
FI0054601-00 C
Page iii
SANbox 6142 Intelligent Storage Router
User’s Guide
S
Notes
Page iv
FI0054601-00 C
Table of Contents
1
Introduction
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Related Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
Communications Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2
Federal Communications Commission (FCC) Class A Statement . . .
1-3
Canadian Department of Communications Class A Compliance Statement
1-3
Avis de conformité aux normes du ministère des Communications du
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3
CE Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4
VCCI Class A Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5
Laser Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5
Electrostatic Discharge Sensitivity (ESDS) Precautions . . . . . . . . . . . . . . .
1-5
Accessible Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
License Agreements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
General Public License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6
Terms And Conditions For Copying, Distribution and Modification . . .
1-7
How to Apply These Terms to Your New Programs . . . . . . . . . . . . . . 1-13
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
2
General Description
Router Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Licensed Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SmartWrite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Server/Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote SAN Island Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local SAN Island Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP - Fibre Channel over IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FI0054601-00 C
2-2
2-2
2-2
2-3
2-4
2-6
2-6
2-7
Page v
SANbox 6142 Intelligent Storage Router
User’s Guide
S
Heartbeat LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Power LED (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Fault LED (Amber) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset a Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset and Select Boot Image . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Port LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel SFP Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI/Gigabit Ethernet Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Port – Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Planning
Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FC Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI/Gigabit Ethernet Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Switch Ports and Zoning Requirements . . . . . . . . . . . . . . . .
Multiple Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page vi
2-7
2-7
2-7
2-8
2-8
2-8
2-9
2-9
2-9
2-9
2-10
2-10
2-11
2-12
2-12
2-13
3-1
3-2
3-2
3-2
3-2
3-2
3-3
3-3
3-3
3-3
3-3
3-7
3-8
3-8
3-8
3-8
3-9
3-9
FI0054601-00 C
A
4
SANbox 6142 Intelligent Storage Router
User’s Guide
Installation
Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANbox 6142 Router Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-installation Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mount the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect the Management Workstation to the Router . . . . . . . . . . . . .
Configure the Management Workstation . . . . . . . . . . . . . . . . . . . . . . .
Setting the Workstation IP Address . . . . . . . . . . . . . . . . . . . . . .
Configuring the Workstation Serial Port . . . . . . . . . . . . . . . . . . .
Install SANsurfer iSCSI/FC Router Manager. . . . . . . . . . . . . . . . . . . .
Windows Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Linux Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start SANsurfer iSCSI/FC Router Manager. . . . . . . . . . . . . . . . . . . . .
Connect the Router to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Devices to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using SANsurfer iSCSI/FC Router Manager to Install Firmware . . . .
Using the CLI to Install Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
4-1
4-1
4-2
4-2
4-2
4-4
4-4
4-5
4-5
4-5
4-6
4-6
4-7
4-7
4-8
4-8
4-9
4-10
4-11
4-11
4-11
4-12
Diagnostics and Troubleshooting
Chassis Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Power LED is Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Fault LED is On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Self-Test Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED Blink Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heartbeat Blink Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Error Blink Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Port IP Address Conflict Blink Pattern . . . . . . . . . . . . . .
Over-Temperature Blink Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recovering a Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FI0054601-00 C
5-1
5-2
5-2
5-2
5-3
5-3
5-3
5-4
5-4
5-5
Page vii
SANbox 6142 Intelligent Storage Router
User’s Guide
6
S
Removal/Replacement
SFP Transceiver Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . .
Router Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
SANsurfer iSCSI/FC Router Manager
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wizards Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Help Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Action Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Tree Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANbox 6142 Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Management Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigned Remote Router Tab. . . . . . . . . . . . . . . . . . . . . . . . . . .
Topology Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FC Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FC Port Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FC Port Advanced Configuration Tab . . . . . . . . . . . . . . . . . . . . .
FC Port Performance Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced Configuration Tab . . . . . . . . . . . . . . . . . . . . . . . . . . .
Statistics Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Discovered iSCSI Initiators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Presented Target Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Presented Target Tab . . . . . . . . . . . . . . . . . . . . . . . . . .
FC Discovered Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Presented Devices Tab . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Presented Target List Tabbed Page . . . . . . . . . . . . . . . . .
Page viii
6-1
6-2
6-2
6-2
7-1
7-3
7-4
7-4
7-4
7-5
7-7
7-7
7-8
7-10
7-12
7-12
7-17
7-19
7-19
7-20
7-20
7-21
7-21
7-22
7-23
7-24
7-27
7-30
7-31
7-31
7-32
7-33
7-34
7-35
7-35
7-36
FI0054601-00 C
A
SANbox 6142 Intelligent Storage Router
User’s Guide
iSCSI Discovered Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Tabbed Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Information Tabbed Page . . . . . . . . . . . . . . . . . . . .
FCIP Route Statistics Tabbed Page . . . . . . . . . . . . . . . . . . . . . .
Wizards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add Initiator Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FW Update Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map Local Initiator/Target Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unmap Local Initiator/Target Wizard . . . . . . . . . . . . . . . . . . . . . . . . . .
Add Remote Router Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove Remote Router Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map Remote Initiator/Target Wizard . . . . . . . . . . . . . . . . . . . . . . . . . .
Unmap Remote Initiator/Target Wizard . . . . . . . . . . . . . . . . . . . . . . . .
Discover iSCSI Target Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Remove Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A
7-38
7-38
7-39
7-40
7-42
7-43
7-44
7-49
7-51
7-55
7-63
7-68
7-72
7-75
7-81
7-84
7-86
7-92
Command Reference
Logging On to a SAN Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guest Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Working with SAN Router Configurations . . . . . . . . . . . . . . . . . . . . . . . . . .
Modifying a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving and Restoring Router Configurations . . . . . . . . . . . . . . . . . . .
Save Router Configuration and Persistence . . . . . . . . . . . . . . .
Restore Router Configuration and Persistence . . . . . . . . . . . . .
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Admin Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beacon Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clear Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FcipRoute Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Help Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Image Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initiator Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Localmap Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logout Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FI0054601-00 C
A-1
A-2
A-2
A-2
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-13
A-14
A-16
A-17
A-18
A-20
A-23
Page ix
SANbox 6142 Intelligent Storage Router
User’s Guide
S
Password Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ping Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quit Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reboot Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Map Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Peer Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Factory Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set CHAP Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set FC Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Features Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set iSCSI Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set iSNS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Mgmt Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set NTP Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Properties Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set SNMP Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set System Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show CHAP Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show FC Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show FcipRoutes Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Features Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Initiators Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show iSCSI Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show iSNS Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Localmaps Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Logs Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Memory Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Mgmt Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show NTP Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Performance Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Presented Initiators Command . . . . . . . . . . . . . . . . . . . . . . . . .
Show Presented Targets Command . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Properties Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Remotemaps Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Remotepeers Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show SNMP Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page x
A-24
A-25
A-26
A-27
A-28
A-32
A-34
A-35
A-37
A-39
A-40
A-41
A-42
A-44
A-45
A-46
A-47
A-48
A-50
A-51
A-54
A-55
A-56
A-57
A-58
A-59
A-61
A-62
A-63
A-64
A-65
A-66
A-67
A-69
A-70
A-72
A-73
A-74
A-75
FI0054601-00 C
A
SANbox 6142 Intelligent Storage Router
User’s Guide
Show Stats Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show System Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Targets Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show VLAN Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shutdown Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Target Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traceroute Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B
A-76
A-79
A-80
A-81
A-82
A-83
A-84
Log Messages
Log Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOE Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fatal Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FC Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOE Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FI0054601-00 C
B-1
B-1
B-1
B-4
B-5
B-6
B-8
B-9
B-9
B-10
B-10
B-18
B-20
B-22
B-25
B-25
B-25
B-28
B-30
B-31
Page xi
SANbox 6142 Intelligent Storage Router
User’s Guide
C
S
Configuring CHAP
CHAP Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring CHAP Using CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLI—Discovery Session—Bi-directional CHAP . . . . . . . . . . . . . . . . .
CLI—Discovery Session—Uni-directional CHAP . . . . . . . . . . . . . . . .
CLI—Normal Session—Bi-directional CHAP . . . . . . . . . . . . . . . . . . .
CLI—Normal Session—Uni-directional CHAP . . . . . . . . . . . . . . . . . .
Configuring CHAP Using the GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GUI—Discovery Session—Bi-directional CHAP . . . . . . . . . . . . . . . .
GUI—Discovery Session—Uni-directional CHAP . . . . . . . . . . . . . . .
GUI—Normal Session—Bi-directional CHAP. . . . . . . . . . . . . . . . . . .
GUI—Normal Session—Uni-directional CHAP. . . . . . . . . . . . . . . . . .
D
Simple Network Management Protocol (SNMP)
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Trap Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Information Base (MIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Port Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Port Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notification Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Agent Start Up Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Agent Shut Down Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Port Down Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Port Down Notification . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Generic Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page xii
C-1
C-1
C-1
C-2
C-3
C-4
C-4
C-4
C-5
C-6
C-7
D-1
D-1
D-2
D-3
D-3
D-4
D-6
D-8
D-11
D-11
D-11
D-12
D-12
D-12
D-12
D-13
FI0054601-00 C
A
SANbox 6142 Intelligent Storage Router
User’s Guide
List of Figures
Figure
Page
2-1
SANbox 6142 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-2
Remote SAN Island Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4
2-3
Local SAN Island Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5
2-4
Chassis LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7
2-5
Chassis Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8
2-6
Fibre Channel LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2-7
Gigabit Ethernet (iSCSI) Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-8
Ethernet Management Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-9
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
3-1
LAN Topology - Local SAN Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7
3-2
WAN Topology - Remote SAN Interconnect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7
4-1
SANbox 6142 Router and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
5-1
Chassis Diagnostic LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
7-1
SANsurfer Router Manager Main Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2
7-2
Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3
7-3
File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4
7-4
View Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4
7-5
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4
7-6
Broadcast Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5
7-7
Wizards Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5
7-8
Help Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7
7-9
Tool Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7
7-10 Action Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8
7-11 System Tree Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
7-12 Component Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
7-13 Basic Information Vertical Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
7-14 Management Information Vertical Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
7-15 NTP Server Information Vertical Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
7-16 Security Vertical Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
7-17 SNMP Management Tabbed Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
7-18 Features Tabbed Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
7-19 Topology Tabbed Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
7-20 FC Port Information Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
7-21 FC Port Advanced Configuration Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
7-22 FC Port Performance Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
7-23 iSCSI Port Tabbed Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23
7-24 Advanced Configuration Tabbed Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
7-25 iSCSI Statistics Tabbed Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30
7-26 Discovered iSCSI Initiator Tabbed Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-31
7-27 Local Presented Target Tabbed Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-32
7-28 Remote Presented Target Tabbed Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-33
7-29 FC Discovered Targets Tabbed Pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34
7-30 Remote Presented Devices Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-35
FI0054601-00 C
Page xiii
SANbox 6142 Intelligent Storage Router
User’s Guide
7-31
7-32
7-33
7-34
7-35
7-36
7-37
7-38
7-39
7-40
7-41
7-42
7-43
7-44
7-45
7-46
7-47
7-48
7-49
7-50
7-51
7-52
7-53
7-54
7-55
7-56
7-57
7-58
7-59
7-60
7-61
7-62
7-63
7-64
7-65
7-66
7-67
7-68
7-69
7-70
7-71
7-72
7-73
7-74
7-75
S
iSCSI Presented Target List Tabbed Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Discovered Targets Tabbed Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Tabbed Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Statistics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Port Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Port Connection Settings Panel Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Port IPv6 Settings Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm Changes Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Port Configuration Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Wizard Finish Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Create an Initiator Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Check Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Tree with New iSCSI Initiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Router Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware File Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm Changes Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Check Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Update Status Dialog Box—Progress . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finish Dialog Box (Successful Firmware Update) . . . . . . . . . . . . . . . . . . . . . . . . . .
Initiator Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select a Target Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select Initiator Port Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select Target Presentation Port Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm Changes Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Check Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initiator/Target Mapping Configuration Status Dialog Box . . . . . . . . . . . . . . . . . . . .
Discovered iSCSI Initiators - Local Presented Targets . . . . . . . . . . . . . . . . . . . . . .
Initiator Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Presented Target Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Check Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpresent Initiator/Target Status Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Discovered iSCSI Initiators - Local Presented Targets . . . . . . . . . . . . . . . . . . . . . .
Remote Router’s IP Address Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Router Admin Password Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add Remote Router Status Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigned Remote Router Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Topology Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select Remote Router Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Router Admin Password Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refresh Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove Remote Router Completion Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Mapping Option Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page xiv
7-37
7-38
7-39
7-42
7-44
7-45
7-46
7-47
7-48
7-49
7-50
7-50
7-51
7-51
7-52
7-53
7-53
7-54
7-54
7-55
7-56
7-57
7-58
7-59
7-60
7-61
7-62
7-63
7-64
7-65
7-66
7-67
7-68
7-69
7-69
7-70
7-71
7-72
7-73
7-73
7-74
7-75
7-76
7-77
7-78
FI0054601-00 C
A
7-76
7-77
7-78
7-79
7-80
7-81
7-82
7-83
7-84
7-85
7-86
7-87
7-88
7-89
7-90
7-91
7-92
7-93
7-94
7-95
7-96
7-97
7-98
SANbox 6142 Intelligent Storage Router
User’s Guide
Confirm Mapping Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Password Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Router Admin Password Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refresh Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Mapped Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Router Admin Password Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Unmap Initiator-Target Status Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . .
Discover iSCSI Target Wizard—IP Address Dialog Box . . . . . . . . . . . . . . . . . . . . .
Discover iSCSI Target Wizard—Security Check Dialog Box . . . . . . . . . . . . . . . . . .
Discover iSCSI Target Wizard—Refresh Dialog Box. . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Discovered Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard—Warning Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard—Port Selection Dialog Box . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard—Local and Remote IP Address Dialog Box . . . . . . . . . .
FCIP Route Add Wizard—TCP/IP Options Dialog Box . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard—FCIP Options Dialog Box. . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard—Security Check Dialog Box . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Add Wizard—Completed Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Remove Wizard—Warning Dialog Box . . . . . . . . . . . . . . . . . . . . . . . .
FCIP Route Remove Wizard—Route Selection Dialog Box . . . . . . . . . . . . . . . . . .
FCIP Route Remove Wizard—Security Check Dialog Box . . . . . . . . . . . . . . . . . . .
FCIP Route Remove Wizard—Completed Dialog Box . . . . . . . . . . . . . . . . . . . . . .
7-79
7-79
7-80
7-80
7-81
7-82
7-83
7-83
7-84
7-84
7-85
7-85
7-86
7-87
7-88
7-89
7-90
7-91
7-91
7-92
7-93
7-93
7-94
List of Tables
Table
2-1
2-2
2-3
2-4
3-1
3-2
3-3
3-4
3-5
3-6
4-1
4-2
5-1
7-1
A-1
B-1
B-2
B-3
B-4
System Fault LED Blink Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ-45 to DB-9 Adapter Pin Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 / DS-1 – 1.554 Mbits/Sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T3 / DS-3 – 45 Mbits/Sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DS-5 – 400 Mbits/Sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OC-1 – 50 Mbits/Sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OC-3 – 150 Mbits/Sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OC-12 and Above – 621 Mbits/Sec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Workstation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Fault LED Blink Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SANsurfer Router Manager Main Window Sections . . . . . . . . . . . . . . . . . . . . . . . .
Command Line Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Modules—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Driver—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Driver—Informational Log Messages. . . . . . . . . . . . . . . . . . . . . . . .
User Modules—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FI0054601-00 C
Page
2-7
2-10
2-13
2-13
3-3
3-4
3-4
3-5
3-6
3-6
4-1
4-4
5-3
7-2
A-5
B-1
B-4
B-5
B-6
Page xv
SANbox 6142 Intelligent Storage Router
User’s Guide
B-5
B-6
B-7
B-8
B-9
B-10
B-11
B-12
B-13
B-14
B-15
B-16
D-1
D-2
S
FCIP—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOE—Informational Log Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System—Informational Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Module—Error Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Driver—Error Log Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Driver—Error Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Modules—Error Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System—Error Log Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iSCSI Driver—Fatal Log Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fibre Channel Driver—Fatal Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOE—Fatal Log Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System—Fatal Log Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP Trap Configuration Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page xvi
B-8
B-9
B-9
B-10
B-18
B-20
B-22
B-25
B-25
B-28
B-30
B-31
D-1
D-2
FI0054601-00 C
1
Introduction
This manual describes the features and installation of the QLogic SANbox 6142
Intelligent Storage Router (iSR-6142), also referred to as the SANbox 6142 router
or simply router.
Intended Audience
This guide is for users who are responsible for installing, managing, and servicing
the SANbox 6142 router and the storage area network (SAN) equipment to which
it is attached.
Related Materials
„
Internet Protocol, Version 6 (IPv6) Specification., RFC2460.
„
Neighbor Discovery for IP Version 6 (IPv6), RFC2461.
„
IPv6 Stateless Address Autoconfiguration, RFC2462.
„
Internet Control Message Protocol (ICMPv6) for the Internet Protocol
Version 6 (IPv6) Specification, RFC2463.
„
Transmission of IPv6 Packets over Ethernet Networks, RFC2464.
„
iSCSI draft standard draft-ietf-ips-iSCSI-20
„
Internet engineering task force (IETF) – iSCSI Requirements and Design
Considerations, iSCSI Naming and Discovery, Internet Protocol
Specification (IPv4), RFC793
„
Transmission Control Protocol (TCP) Specification, RFC1122, Requirements
for Internet Hosts-Communication Layers
„
TCP Extensions for High Performance, RFC1323
„
TCP Congestion Control, RFC2581
„
NewReno Modification to TCP’s Fast Recovery Algorithm, RFC2582
„
ANSI SCSI – SCSI-3 Architecture Model (SAM), X3T10/994D/Rev 18,
SCSI-3 Controller Command Set, X3T10/Project 1047D/Rev 6c. IEEE –
802.1Q Virtual LAN (VLAN), 802.1p Priority of Service, 802.3x Flow Control,
802.3ad Link Aggregation
FI0054601-00 C
1-1
S
1 – Introduction
Safety
„
SCSI-3 Fibre Channel Protocol (SCSI-FCP), X3.269:1996
„
Fibre Channel Physical and Signaling Interface (FC-PH), X3.230:199
„
Fibre Channel 2nd Generation (FC-PH-2), X3.297:1997
„
Third Generation Fibre Channel Physical and Signaling Interface (FC-PH-3),
X3.303:1998, Fibre Channel-Arbitrated Loop (FC-AL-2), working draft,
revision 6.4, August 28, 1998
„
Fibre Channel Fabric Loop Attachment Technical Report (FC-FLA)
NCITS/TR-20:1998, Fibre Channel-Private Loop Direct Attach Technical
Report (FC-PLDA)
„
SCSI Fibre Channel Protocol-2 (FCP-2) working draft, revision 3, October1,
1999
„
Fibre Channel over TCP/IP (FCIP), RFC3821
„
ANSI Information Technology-SCSI 3 Architecture Model, revision 18,
November 27, 1995
Safety
WARNING!!
A Warning notice indicates a hazard that has the potential of causing minor
personal injury.
CAUTION!
A Caution notice indicates the presence of a hazard that has the potential of
causing damage to the equipment.
Communications Statements
The following statements apply to this product. The statements for other products
intended for use with this product appear in their accompanying manuals.
1-2
FI0054601-00 C
A
1 – Introduction
Communications Statements
Federal Communications Commission (FCC) Class A
Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy, and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause unacceptable
interference, in which case the user will be required to correct the interference at
their own expense.
Neither the provider nor the manufacturer is responsible for any radio or television
interference caused by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's authority to operate
the equipment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
„
This device may not cause harmful interference, and
„
This device must accept any interference received, including interference
that may cause undesired operation.
Canadian Department of Communications Class A
Compliance Statement
This equipment does not exceed Class A limits for radio emissions for digital
apparatus, set out in Radio Interference Regulation of the Canadian Department
of Communications. Operation in a residential area may cause unacceptable
interference to radio and TV reception requiring the owner or operator to take
whatever steps necessary to correct the interference.
Avis de conformité aux normes du ministère des
Communications du Canada
Cet équipement ne dépasse pas les limites de Classe A d'émission de bruits
radioélectriques por les appareils numériques, telles que prescrites par le
Réglement sur le brouillage radioélectrique établi par le ministère des
Communications du Canada. L'exploitation faite en milieu résidentiel peut
entraîner le brouillage des réceptions radio et télé, ce qui obligerait le propriétaire
ou l'opérateur à prendre les dispositions nécwssaires pour en éliminer les causes.
FI0054601-00 C
1-3
S
1 – Introduction
Communications Statements
CE Statement
The CE symbol on the equipment indicates that this system complies with the
EMC (Electromagnetic Compatibility) directive of the European Community
(89/336/EEC) and to the Low Voltage (Safety) Directive (73/23/EEC). Such
marking indicates that this system meets or exceeds the following technical
standards:
1-4
„
EN60950-1, A11:2004 – “Safety of Information Technology Equipment,
Including Electrical Business Equipment”.
„
EN 55022:1998, A1:2000, A2:2003 – “Limits and Methods of Measurement
of Radio Interference Characteristics of Information Technology Equipment”.
„
EN 55024:1998, A1:2001, A2:2003 – “Electromagnetic compatibility Generic immunity standard Part 1 – Residential commercial, and light
industry.”
„
EN 61000-4-2 – 1995, A1:1998, A2 – 2001 – “Electrostatic Discharge
Immunity Test”
„
EN 61000-4-3 – 2002 – “Radiated, Radio-Frequency, Electromagnetic
Field Immunity Test”
„
EN 61000-4-4 – 1995, A1:2001, A2:2001 – “Electrical Fast
Transient/Burst Immunity Test”
„
EN 61000-4-5 – 1995, A1:2001 – “Surge Immunity Test”
„
EN 61000-4-6 – 1996, A1:2001 – “Immunity To Conducted
Disturbances, Induced By Radio-Frequency Fields”
„
EN 61000-4-8 – 1993, A1:2001 – "Power Frequency Magnetic Field
Immunity Test”
„
EN 61000-4-11 Second Edition – 2004 – “Voltage Dips, Short
Interruptions And Voltage Variations Immunity Tests”
„
EN 61000-3-2 – 2000 – “Limits For Harmonic Current Emissions (Equipment
Input Current Less Than/Equal To 16 A Per Phase)” Class A
„
EN 61000-3-3 – 1995, A1:2001 – “Limitation Of Voltage Fluctuations And
Flicker In Low-Voltage Supply Systems For Equipment With Rated Current
Less Than Or Equal To 16 A”
FI0054601-00 C
A
1 – Introduction
Laser Safety Information
VCCI Class A Statement
This is a Class A product based on the standard of the Voluntary Control Council
For Interference by Information Technology Equipment (VCCI). If this equipment
is used in a domestic environment, radio disturbance may arise. When such
trouble occurs, the user may be required to take corrective actions.
Laser Safety Information
This product may use Class 1 laser optical transceivers to communicate over the
fiber optic conductors. The U.S. Department of Health and Human Services
(DHHS) does not consider Class 1 lasers to be hazardous. The International
Electrotechnical Commission (IEC) 825 Laser Safety Standard requires labeling in
English, German, Finnish, and French stating that the product uses Class 1
lasers. Because it is impractical to label the transceivers, the following label is
provided in this manual.
Electrostatic Discharge Sensitivity (ESDS)
Precautions
The assemblies used in the switch chassis are ESD sensitive. Observe ESD
handling procedures when handling any assembly used in the switch chassis.
FI0054601-00 C
1-5
S
1 – Introduction
Accessible Parts
Accessible Parts
The following field replaceable units (FRUs) are supported by the SANbox 6142
router:
„
Small form-factor pluggable (SFP) optical transceivers
License Agreements
Refer to the QLogic Software End User License Agreement for a complete listing
of all license agreements affecting this product.
General Public License
QLogic SANbox routers are powered by the Linux operating system. A
machine-readable copy of the Linux source code is available upon written request
to the following address. A nominal fee will be charged for reproduction, shipping,
and handling costs in accordance with the General Public License.
QLogic Corporation
26600 Aliso Viejo Parkway
Aliso Viejo, CA 92656
Attention – Technical Support – Source Request
CAUTION!
Installation of software or files not authorized by QLogic will immediately and
irrevocably void all warranty and service contracts on the affected units.
The following General Public License has been reproduced with permission from:
GNU General Public License
Version 2, June 1991
Copyright 1989, 1991 Free Software Foundation, Inc.
59 Temple Place – Suite 330, Boston, MA 02111-1307, USA
Preamble
The licenses for most software are designed to take away your freedom to share
and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software - to make sure the
software is free for all its users. This General Public License applies to most of the
Free Software Foundation’s software and to any other program whose authors
commit to using it. (Some Free Software Foundation software is covered by the
GNU Library General Public License instead). You can apply it to your programs,
too.
1-6
FI0054601-00 C
A
1 – Introduction
General Public License
When we speak of free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service if you wish), that you
receive source code or can get it if you want it, that you can change the software
or use pieces of it in new programs, and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you
these rights or to ask you to surrender the rights. These restrictions translate to
certain responsibilities for you if you distribute copies of the software, or if you
modify it.
For example, if you distribute copies of such a program, whether gratis or for a
fee, you must give the recipients all the rights that you have. You must make sure
that they, too, receive or can get the source code. And you must show them these
terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you
this license which gives you legal permission to copy, distribute and/or modify the
software.
Also, for each author’s protection and ours, we want to make certain that
everyone understands that there is no warranty for this free software. If the
software is modified by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any problems introduced by
others will not reflect on the original authors’ reputation.
Finally, any free program is threatened constantly by software patents. We wish to
avoid the danger that redistributors of a free program will individually obtain patent
licenses, in effect making the program propriety. To prevent this, we have made it
clear that any patent must be licensed for everyone’s free use or not licensed at
all.
The precise terms and conditions for copying, distribution and modification follow.
Terms And Conditions For Copying, Distribution and
Modification
1.
FI0054601-00 C
This license applies to any program or other work which contains a notice
placed by the copyright holder saying it may be distributed under the terms
of this General Public License. The "Program", below, refers to any such
program or work, and a "work based on the Program" means either the
Program or any derivative work under copyright law – that is to say, a work
containing the Program or a portion of it, either verbatim or with
modifications and/or translated into another language. (Hereinafter,
1-7
1 – Introduction
General Public License
S
translation is included without limitation in the term "modification".) Each
licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered
by this License – they are outside its scope. The act of running the Program
is not restricted, and the output from the Program is covered only if tis
contents constitute a work based on the Program (independent of having
been made by running the Program). Whether that is true depends on what
the Program does.
2.
You may copy and distribute verbatim copies of the Program’s source code
as you receive it, in any medium, provided that you conspicuously and
appropriately public on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer to this License
and to the absence of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
3.
You may modify your copy or copies of the Program or any portion of it, thus
forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you
also meet all of these conditions:
a.
You must cause the modified files to carry prominent notices stating
that you changed the files and the date of any change.
b.
You must cause any work that you distribute or publish, that in whole or
in part contains or is derived from the Program or any part thereof, to
be licensed as a whole at no charge to all third parties under the terms
of this License.
c.
If the modified program normally reads commands interactively when
run, you must cause it, when started running for such interactive use in
the most ordinary way, to print or display an announcement including
an appropriate copyright notice and a notice that there is no warranty
(or else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling the user
how to view a copy of this License. (Exception – if the Program itself is
interactive but does not normally print such an announcement, your
work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves, then
this License, and its terms, do not apply to those sections when you
distribute them as separate works. But when you distribute the same
sections as part of the whole must be on the terms of this License, whose
permissions for other Licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
1-8
FI0054601-00 C
A
1 – Introduction
General Public License
Thus, it is not the intent of this section to claim rights or contest your rights to
work written entirely by you; rather, the intent is to exercise the right to
control the distribution of derivative or collective works based on the
Program.
In addition, mere aggregation of another work not based on the Program
with the Program (or with a work based on the Program) on a volume of a
storage distribution medium does not bring the other work under the scope
of this License.
4.
You may copy and distribute the Program (or a work based on it, under
Section 2) in object code or executable form under the terms of paragraphs
1 and 2 above provided that you also do one of the following:
a.
Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of paragraphs
1 and 2 above on a medium customarily used for software interchange
– or,
b.
Accompany it with a written offer, valid for at least three years, to give
any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy of
the corresponding source code, to be distributed under the terms of
paragraphs 1 and 2 above on a medium customarily used for software
interchange; or,
c.
Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed only
for noncommercial distribution and only if you received the program in
object code or executable form with such an offer, in accord with
paragraph b.)
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means all
the source code for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation and installation of
the executable. However, as a special exception, the source code
distributed need not include anything that is normally distributed (in either
source or binary form) with the major components (compiler, kernel, and so
on) of the operating system on which the executable runs, unless that
component itself accompanies the executable.
If distribution of executable or object code is made by offering access to
copy from a designated place, then offering equivalent access to copy the
source code from the same place counts as distribution of the source code,
even though third parties are not compelled to copy the source along with
the object code.
FI0054601-00 C
1-9
1 – Introduction
General Public License
S
5.
You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy,
modify, sublicense or distribute the Program is void, and will automatically
terminate your rights under this License. However, parties who have
received copies, or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full compliance.
6.
You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you
do not accept this License. Therefore, by modifying or distributing the
Program (or any work based on the Program), you indicate your acceptance
of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based on it.
7.
Each time you redistribute the Program (or any work based on the Program),
the recipient automatically receives a license from the original Licensor to
copy, distribute or modify the Program subject to these terms and conditions.
You may not impose any further restrictions on the recipients’ exercise of the
rights granted herein. You are not responsible for enforcing compliance by
third parties of this License.
8.
If, as a consequence of a court judgement or allegation of patent
infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise) that
contradict the conditions of this License, they do not excuse you from the
conditions of this License. If you cannot distribute so as to satisfy
simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the Program at
all. For example, if a patent license would not permit royalty-free
redistribution of the Program by all those who receive copies directly or
indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system, which is implemented by public license practices. Many
people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot impose
that choice.
1-10
FI0054601-00 C
A
1 – Introduction
General Public License
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
9.
If the distribution and/or use of the Program is restricted in certain countries
either by patents or by copyright interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
10.
The Free Software Foundation may publish revised and/or new versions of
the General Public License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in detail to address new
problems or concerns.
11.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and "any later
version", you have the option of following the terms and conditions either of
that version or of any later version published by the Free Software
Foundation. If the Program does not specify a version number of this
License, you may choose any version ever published by the Free Software
Foundation.
12.
If you wish to incorporate parts of the Program into other free programs
whose distribution conditions are different, write to the author to ask for
permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free software and of
promoting the sharing and reuse of the software generally.
NO WARRANTY
13.
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS
NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
14.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
FI0054601-00 C
1-11
1 – Introduction
General Public License
S
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
1-12
FI0054601-00 C
A
1 – Introduction
General Public License
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use
to the public, the best way to achieve this is to make it free software which
everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to
the start of each source file to most effectively convey the exclusion of warranty;
and each file should have at least the "copyright" line and a pointer to where the
full notice is found.
One line to give the program’s name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
You should have received a copy of the GNU General Public License along with
this program; if not write to the Free Software Foundation, Inc., 59 Temple Place Suite 330, Boston, MA 02111-1307, USA.
Also information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in
an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ’show
w’. This is free software, and you are welcome to redistribute it under certain
conditions; type ’show c’ for details.
The hypothetical commands ’show w’ and ’show c’ should the appropriate pats of
the General Public License. Of course, the commands you use may be called
something other than ’show w’ and ’show c’; they could even be mouse-clicks or
menu items - whatever suits your program.
You should also get your employer (if you work as a programmer) or your school,
if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a
sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
’Gnomovision’ (which makes passes at compilers) written by James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
FI0054601-00 C
1-13
S
1 – Introduction
Technical Support
This General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may consider it
more useful to permit linking proprietary applications with the library. If this is what
you want to do, use the GNU Library General Public License instead of this
License.
Technical Support
Customers should contact their authorized maintenance provider for technical
support of their QLogic switch products. QLogic-direct customers may contact
QLogic Technical Support; others will be redirected to their authorized
maintenance provider.
Visit the QLogic support Web site listed in Contact Information for the latest
firmware and software updates.
Availability
QLogic Technical Support for products under warranty is available during local
standard working hours excluding QLogic Observed Holidays.
Training
QLogic offers certification training for the technical professional for both the
SANblade® HBAs and the SANbox® switches. From the training link at
www.qlogic.com, you may choose Electronic-Based Training or schedule an
intensive "hands-on" Certification course.
Technical Certification courses include installation, maintenance and
troubleshooting QLogic SAN products. Upon demonstrating knowledge using live
equipment, QLogic awards a certificate identifying the student as a Certified
Professional. The training professionals at QLogic may be reached by email at
tech.training@qlogic.com.
Contact Information
1-14
Support Headquarters
QLogic Corporation
12984 Valley View Road
Eden Prairie, MN 55344-3657
USA
QLogic Web Site
www.qlogic.com
Technical Support Web Site
support.qlogic.com
Technical Support Email
support@qlogic.com
Technical Training Email
tech.training@qlogic.com
FI0054601-00 C
A
1 – Introduction
Technical Support
North American Region
Email
support@qlogic.com
Phone
+1-952-932-4040
Fax
+1 952-974-4910
Europe, Middle East, and Africa Region
Email
emeasupport@qlogic.com
Phone Numbers by Language
+353 1 6924960
+353 1 6924961
+353 1 6924962
+353 1 6924963
+353 1 6924964
+353 1 6924965
- English
- Français
- Deutsch
- Español
- Português
- Italiano
Asia Pacific Region
Email
apacsupport@qlogic.com
Phone Numbers by Language
+63-2-885-6712 - English
+63-2-885-6713 - (Mandarin)
+63-2-885-6714 - (Japanese)
+63-2-885-6715 - (Korean)
Latin and South America Region
FI0054601-00 C
Email
calasupport@qlogic.com
Phone Numbers by Language
+52 55 5278 7016 - English
+52 55 5278 7017 - Español
+52 55 5278 7015 - Português
1-15
1 – Introduction
Technical Support
1-16
S
FI0054601-00 C
2
General Description
This section describes the following features and capabilities of the SANbox 6142
router:
„
Router Capabilities (see page 2-2)
„
Licensed Features (see page 2-2)
„
Remote SAN Island Connectivity (see page 2-4)
„
Local SAN Island Connectivity (see page 2-6)
„
FCIP - Fibre Channel over IP (see page 2-6)
„
Chassis LEDs (see page 2-7)
„
Chassis Controls (see page 2-8)
„
Fibre Channel Ports (see page 2-10)
„
Fibre Channel SFP Transceivers (see page 2-11)
„
iSCSI/Gigabit Ethernet Port LEDs (see page 2-12)
„
Ethernet Port – Management (see page 2-12)
„
Serial Port see page 2-13)
Figure 2-1 SANbox 6142 Router
FI0054601-00 C
2-1
S
2 – General Description
Router Capabilities
Router Capabilities
The SANbox 6142 is a bi-directional FC-to-iSCSI router. It supports the following
topologies:
„
Two remote SAN islands (single or multi-vendor fabrics) (see page 2-4)
„
Local connectivity (see page 2-6)
„
„
FC SAN islands (single or multi-vendor fabrics)
„
iSCSI Servers to FC SAN
„
FC servers to iSCSI SAN
FCIP – Fibre Channel over IP (see page 2-6)
When using the SANbox 6142 to connect two Fibre Channel SANs, E-ports are
not required on the Fiber Channel switches. This allows you to connect
multi-vendor FC SANs (switches) without concern for the compatibility of the
E-Ports and/or B-Ports between different switch vendors.
The SANbox 6142 has the following optional features:
„
SmartWrite™ – Provides write performance improvements.
„
Additional Server/Ports – Provides additional connectivity (see page 2-3).
Licensed Features
The SANbox 6142 router has two features that are available by a license key:
„
SmartWrite
„
Additional Server/Ports
SmartWrite
When connecting SAN over long distances, round-trip delays create significant
impact to the performance. Typically, data writes involve two or more round-trip
latencies that create a significant barrier to the data replication performance.
SmartWrite technology is designed to minimize the round-trip latency of any write
I/O to a single round-trip latency.
This Feature Key offers the following benefits:
2-2
„
Minimizes round-trip delays for any data write operation to a single
round-trip latency.
„
Allows load balancing over multiple IP links.
FI0054601-00 C
A
2 – General Description
Licensed Features
„
Provides failover and failback between two gigabit ethernet links.
„
Allows data compression. This is very useful when data round-trip latencies
between two routers exceed more than 50 ms or long distance link rate is
equal or less than 4500 Mbits/sec (DS-3 line rate)
SmartWrite is an optional feature which requires the purchase of a license key.
You may enter the SmartWrite feature key using the SANsurfer Router Manager
(see page 7-19) or Command Line Interface (CLI) (see page A-41).
Qualified applications using SmartWrite include:
„
Server connected to Remote FC Storage array
„
Array Data Replication applications
„
EMC – Mirroview™ - EMC
„
EMC – SAN Copy™
„
HDS / Hitachi – True Copy™ with Fabric connect
„
HP – CA for XP
All other Data replication applications like IBM Shadow Copy™, EMC - SRDF, etc.
should use the router’s FCIP mode.
Additional Server/Ports
SANbox 6142 supports mapping of up to 62 Server/Ports between two SANs. The
default configuration allows the mapping of 16 server/ports between SANs. For
example, you may map 8 iSCSI initiators to FC SAN and map 8 FC devices from
one FC SAN to another FC SAN. If your network requires more mappings, you
can add a feature key to support additional mappings in 23 server/port increments
as follows:
„
16 Server/Port mappings - the default configuration.
„
39 Server/Port mappings - includes the default 16 plus one “23 server/port
license”.
„
62 Server/Port mappings - includes the default 16 plus two “23 server/port
licenses”.
Additional Server/Ports is an optional feature which requires purchasing a license
key. You may purchase up to two feature keys.
You can enter the Additional Server/Ports feature key using the SANsurfer Router
Manager (see page 7-19) or Command Line Interface (CLI) (see page A-41).
FI0054601-00 C
2-3
S
2 – General Description
Remote SAN Island Connectivity
Remote SAN Island Connectivity
The SANbox 6142 Intelligent Router supports inter-connecting remote SAN
islands (see Figure 2-2).
Figure 2-2 Remote SAN Island Connectivity
This configuration has the following additional requirements:
„
At least one FC Port of SANbox 6142 connected to FC SAN.
„
Accessibility between the iSCSI/ GE (GE identifies Gigabit Ethernet ports on
the router) Port IP addresses of remote router and iSCSI/GE port IP
addresses of local routers.
„
Accessibility between the remote SANbox 6142 management port IP
address and local SANbox 6142 management port IP address.
When connecting SANs over long distances, it’s important to determine the
round-trip latencies between two router connections. You can discover these
round-trip latencies using the ping command in CLI. (See page A-25.)
Using this round-trip latency number, you can determine the window scaling factor
for GE (iSCSI) port, as described in Performance Tuning on page 3-3. By default,
window scaling is set to 1 (64K) TCP window size.
2-4
FI0054601-00 C
A
2 – General Description
Remote SAN Island Connectivity
To map remote FC devices to local SAN:
1.
If the remote router is not already associated with a local router, use either
the SANsurfer Add Remote Router wizard (see page 7-68) or the CLI
command remotepeer add (see page A-32) to associate the two routers
with each other.
2.
Use the SANsurfer Map Remote Initiator/Target wizard (see page 7-75) or
the CLI remotemap add command (see page A-28) to create the initiator to
target mapping.
Figure 2-3 Local SAN Island Connectivity
The SANbox 6142 Intelligent Router supports inter-connecting local FC SAN
islands. It also supports bridging iSCSI devices on the LAN to FC devices on the
SAN (see Figure 2-33). It provides:
„
FC storage from one SAN to a FC server on different SAN.
„
FC storage to iSCSI servers.
„
SCSI storage to FC servers.
FI0054601-00 C
2-5
2 – General Description
Local SAN Island Connectivity
S
Local SAN Island Connectivity
You can use either the SANsurfer Map Local Initiator/Target wizard (see
page 7-55) or the CLI localmap add command (see page A-20) to map any of
the following connections:
„
iSCSI Server to an FC Device (Target)
„
FC server to an iSCSI Device (Target)
„
FC Server from one SAN to FC target on another SAN
CAUTION!
When adding multiple routers in the same physical SAN, you must import a
given FC device from a remote SAN on only one SANbox 6142 in the local
physical SAN. If you import the same FC device from multiple SANbox
6142s into the same physical SAN, the system duplicates FC world wide
port names (WWPNs). This can disrupt the SAN.
FCIP - Fibre Channel over IP
The SANbox 6142 Intelligent Router supports FCIP, Fibre Channel over IP. The
FCIP protocol as implemented in the router is not guaranteed nor has it been
tested to be compatible with other vendor FCIP implementations. The router
supports up to two FCIP routes; each route requires a dedicated FC and GE port
pair.
2-6
„
Merge FC fabrics over LAN/WAN
„
N-port to fabric over LAN/WAN
„
N-port to N-port over LAN/WAN
FI0054601-00 C
A
2 – General Description
Chassis LEDs
Chassis LEDs
The chassis LEDs shown in Figure 2-4 provide information about the router’s
operational status. These LEDs include the input power LED, heartbeat LED, and
the system fault LED. To apply power to the router, plug the power cord into the
router AC power receptacle and into a 100 VAC to 240 VAC, 50 Hz to 60 Hz
power source.
Figure 2-4 Chassis LEDs
Heartbeat LED (Green)
The heartbeat LED blinks once a second as long the the router firmware is
operational.
Input Power LED (Green)
The power LED shows the voltage status at the router logic circuit board. During
normal operation, this LED lights up to show that the router logic circuit board is
receiving the DC voltage from the power supply.
System Fault LED (Amber)
The system fault LED lights up to show that a fault exists in the router firmware or
hardware. Fault conditions include POST errors and over-temperature conditions.
The LED shows a blink code for POST errors and the over temperature condition.
See Figure 2-4 and Table 2-1.
Table 2-1. System Fault LED Blink Patterns
System
Fault LED
FI0054601-00 C
Condition
OFF
OK (operational)
3 Blinks
System error
4 Blinks
Management port IP address conflict
5 Blinks
Over temperature
1 Blink
Beacon - synchronized with the Heartbeat LED
2-7
S
2 – General Description
Chassis Controls
Chassis Controls
The maintenance button shown in Figure 2-5 is the only chassis control. Pressing
this button resets the router or recovers the router if it has become disabled.
Figure 2-5 Chassis Controls
Maintenance Button
The maintenance button is a multifunction momentary switch on the front panel. It
has the following functions:
„
Reset a Router (see page 2-9)
„
Reset and Select Boot Image (see page 2-9)
„
Reset IP Address (see section page 2-9)
„
Enable DHCP (see section page 2-9)
„
Restore Factory Defaults (see page 2-9)
Reset a Router
To reset the router, use a pointed, nonmetallic tool to momentarily press and
release (less than two seconds) the maintenance button. The router responds as
follows:
2-8
1.
All the chassis LEDs illuminate.
2.
After about 2 seconds, the POST begins, turning off the heartbeat and
system fault LEDs.
3.
When the POST is complete, the power LED is on and the heartbeat LED
flashes once per second.
FI0054601-00 C
A
2 – General Description
Chassis Controls
Reset and Select Boot Image
You can reset the router using either the primary or secondary boot image:
„
Primary Image – To reset the router and select the primary boot image, use
a pointed, nonmetallic tool to press and hold the maintenance button until
the heartbeat LED flashes once, then release the button. The router will boot
from the primary boot image. The boot time is less than one minute.
„
Secondary Image – To reset the router and select the secondary boot
image, use a pointed, nonmetallic tool to press and hold the maintenance
button until the heartbeat LED flashes twice, then release the button. The
heartbeat LED flashes twice. The router boots from secondary boot image.
The boot time is less than one minute.
Reset IP Address
To reset the router and restore the maintenance port IP address to the default
(10.0.0.1), use a pointed, nonmetallic tool to press and hold the maintenance
button until the heartbeat LED flashes six times, then release the button. The
router boots and sets the maintenance port to IP address 10.0.0.1. The boot
time is less than one minute.
The IP address set by this method is not persistent; to make the change
persistent, use the command line interface (CLI) or SANsurfer Router Manager to
set the IP address. For more information, see page 7-4 and page A-3.
Enable DHCP
To reset the router and configure the maintenance port to use DHCP to acquire its
IP address, use a pointed, nonmetallic tool to press and hold the maintenance
button until the heartbeat LED flashes seven times, then release the button. The
router boots and configures the maintenance port for DHCP. The boot time is less
than one minute.
Enabling DHCP by this method is not persistent; to make the change persistent,
use the command line interface (CLI) or SANsurfer Router Manager to enable
DHCP. For details, see page 7-13 and page A-45.
Restore Factory Defaults
To reset the router and restore it to the factory default configuration, use a pointed,
nonmetallic tool to press the maintenance button and hold it until the heartbeat
LED flashes 20 times, then release the button. The router boots and is restored to
the factory defaults. The boot time is less than one minute.
The router does the following when restored to the factory defaults:
„
Resets all passwords.
„
Resets the maintenance port IP address to 10.0.0.1.
„
Disables the iSCSI ports and sets the IP address to 0.0.0.0.
FI0054601-00 C
2-9
S
2 – General Description
Fibre Channel Ports
„
Erases all presentations.
„
Erases all discovered initiators and targets.
Fibre Channel Ports
The SANbox 6142 router has two Fibre Channel ports, labeled FC1 and FC2, as
shown in page 2-10.
Figure 2-6 Fibre Channel LEDs
Each port is served by a small form-factor pluggable (SFP) optical transceiver and
is capable of 1-Gbps or 2-Gbps transmission. SFPs are hot-pluggable. FC ports
can self-discover both the connection type and transmission speed when
connected to public devices or switches. The port LEDs are located to the right of
their respective ports and provide status and activity information.
Fibre Channel Port LEDs
Each port has three LEDs:
„
The amber LED (top) shows activity (data is passing through the port).
„
The green LED (middle) shows the logged-in or initialization status of the
connected devices. This LED flashes off to show the link rate, once for
1-Gbps speed, and twice for 2-Gbps speed.
„
The yellow (bottom) LED shows an alert (port fault) condition.
Table 2-2 describes the LED blink patterns and their meanings.
Table 2-2. Port LEDs
Activity
2-10
Amber LED
Green LED
Yellow LED
Power OFF
OFF
OFF
OFF
Power ON
(before firmware
initialization)
ON
ON
ON
FI0054601-00 C
A
2 – General Description
Fibre Channel SFP Transceivers
Table 2-2. Port LEDs
Activity
Amber LED
Green LED
Yellow LED
Online
Link established
at 1Gbit
OFF
3 seconds ON
Flashes OFF once
OFF
Activity at 1 Gbps
ON
3 seconds ON
Flashes OFF once
OFF
Online
Link established
at 2 Gbps
OFF
3 seconds ON
Flashes OFF twice
OFF
Activity at 2 Gbps
ON
3 seconds ON
Flashes OFF twice
OFF
Power ON
(after firmware initialization and/or
loss of synchronization)
OFF
ON
ON
Firmware error
OFF
OFF
ON
Fibre Channel SFP Transceivers
The SANbox 6142 router supports SFP optical transceivers for the Fibre Channel
ports. A transceiver converts electrical signals to and from optical laser signals to
transmit and receive data. Duplex fibre optic cables plug into the transceivers,
which then connect to the devices. The Fibre Channel ports are capable of
transmitting at 1-Gbps or 2-Gbps; the transceiver must also be capable of
delivering these rates.
The SFP transceivers are hot pluggable – you can remove or install a transceiver
while the router is operating without harming the router or the transceiver.
However, this interrupts communication with the connected device. For
information about installing and removing SFP optical transceivers, see page 4-5.
FI0054601-00 C
2-11
2 – General Description
iSCSI/Gigabit Ethernet Port LEDs
S
iSCSI/Gigabit Ethernet Port LEDs
The iSCSI/gigabit Ethernet ports shown in Figure 2-7 are RJ-45 connectors that
provide connection to an Ethernet SAN through a 10/100/1000 Base-T Ethernet
cable. The ports are labeled GE1 and GE2.
These ports have two LEDs – the link status LED (green) and the activity LED
(also green).
„
The link status LED lights up continuously after the router establishes an
Ethernet connection.
„
The activity LED lights up when the router sends or receives data over the
connection.
Figure 2-7 Gigabit Ethernet (iSCSI) Ports
Ethernet Port – Management
The Ethernet management port shown in Figure 2-8 is an RJ-45 connector that
provides a connection to a management workstation through a 10/100 Base-T
Ethernet cable. The port is labeled MGMT.
Figure 2-8 Ethernet Management Port
You can use a Windows®, Solaris™, or Linux™ workstation to configure and
manage the router over an Ethernet connection using SANsurfer Router Manager,
CLI, or simple network management protocol (SNMP).
The management Ethernet port has two LEDs:
2-12
„
The link status LED (green) is on continuously after the router establishes an
Ethernet connection.
„
The activity LED (green) is on when the router sends or receives data over
the Ethernet connection.
FI0054601-00 C
A
2 – General Description
Serial Port
Serial Port
The SANbox 6142 router is equipped with an RS-232 serial port for maintenance
purposes. Figure 2-9 shows the serial port location. It is labeled IOIOI. You can
manage the router through the serial port using the CLI.
Figure 2-9 Serial Port
The serial port connection requires a standard, eight-wire Ethernet cable and the
RJ45-to-DB9F adapter (supplied) to convert the Ethernet RJ45 connector to a
female DB9 connector. Table 2-3 defines the serial port pins for the router’s RJ45
connector. Table 2-4 defines the pinout for the RJ45 to DB9 adapter.
Table 2-3. Serial Port Pin Identification
RJ45 Pin
Number
RJ-45 Pin
Description
1
Clear to send (CTS)
2
Data set ready (DSR)
3
Receive data (RxD)
4
Signal ground (GND)
5
Data carrier detect (DCD)
6
Transmit data (TxD)
7
Data terminal ready (DTR)
8
Request to send (RTS)
Table 2-4. RJ-45 to DB-9 Adapter Pin Identification
FI0054601-00 C
RJ-45
Pin Number
DB-9F
Pin Definition
DB-9
Pin Number
DB-9
Pin Definition
1
CTS
7
Request to send (RTS)
2
DSR
4
Data terminal ready (DTR)
2-13
S
2 – General Description
Serial Port
Table 2-4. RJ-45 to DB-9 Adapter Pin Identification
RJ-45
Pin Number
DB-9F
Pin Definition
5
DCD
3
RxD
3
Transmit data (TxD)
4
GND
5
Signal ground (GND)
6
TxD
2
Receive data (RxD)
7
DTR
1
Data carrier detect (DCD)
6
Data set ready (DSR)
8
Clear to send (CTS)
9
Ring indicator (RI)
8
2-14
RTS
DB-9
Pin Number
DB-9
Pin Definition
FI0054601-00 C
3
Planning
This section describes how to plan for using the SANbox 6142 router. This
includes the following considerations:
„
Devices (see page 3-1)
„
Device Access (see page 3-2)
„
FC Performance (see page 3-2)
„
iSCSI/Gigabit Ethernet Performance (see page 3-3)
„
Performance Tuning (see page 3-3)
„
Topology (see page 3-7)
„
Fibre Channel Switch Ports and Zoning Requirements (see page 3-8)
„
Multiple Routers (see page 3-8)
„
Management (see page 3-8)
„
Recovery (see page 3-8)
„
Recovery (see page 3-8)
„
Recovery (see page 3-9)
„
Security (see page 3-9)
Devices
When planning to use the router, consider the number of devices and the
anticipated demand. This will determine the required number of ports and in turn
the number of routers.
The router uses SFP transceivers in the 1-Gbps/2-Gbps Fibre Channel (FC) ports,
but some Fibre Channel (FC) devices may not use the same transceivers.
Consider whether the FC device to be connected to the router uses SFP or gigabit
interface converters (GBIC) transceivers, and choose fibre optic cables
accordingly. Use LC-type cable connectors for small form-factor pluggable (SFP)
transceivers and SC-type cable connectors for GBIC transceivers. Also consider
the transmission speed compatibility of your devices, host bus adapters (HBAs),
switches, and SFPs.
FI0054601-00 C
3-1
S
3 – Planning
Device Access
Device Access
Consider device access needs within the FC and iSCSI SANs. Access to an FC
device is controlled by mapping FC device to specific iSCSI initiators. FC devices
may be mapped to more than one initiator. Giving multiple initiators access to an
FC device requires access management.
Fibre Channel
The Fibre Channel ports automatically discover all FC target devices, whether
connected directly (loop) or by fabric (switch).
iSCSI
When an iSCSI initiator logs on, the router records the initiator’s iSCSI name and
IP address. The management interface (command line interface [CLI] or
SANsurfer Router Manager) uses the initiator’s information to simplify the
mapping process.
FC Performance
The SANbox 6142 router supports Fibre Channel service at transmission rates of
1 Gbps or 2 Gbps with a maximum frame size of 2148 bytes. It supports Ethernet
service at transmission rates of 1000-, 100- or 10-Mbps with a maximum
transmission unit (MTU) size of 1500 or 9000 (jumbo frames). Related
performance characteristics include the following:
„
Distance (see page 3-2)
„
Bandwidth (see page 3-3)
„
Latency (see page 3-3)
Distance
Consider the physical distance between Fibre Channel devices. Choose SFP
transceivers that are compatible with the cable type and distance you need.
Each Fibre Channel port is supported by a data buffer with a three-credit capacity;
that is, three maximum sized frames. For fibre optic cables, this enables full
bandwidth over the following approximate distances:
„
5 kilometers at 1 Gbps (0.6 credits/Km)
„
2.5 kilometers at 2 Gbps (1.2 credits/Km)
Transmitting data beyond these distances reduces efficiency because the
transmitting port must wait for an acknowledgement before sending the next
frame.
3-2
FI0054601-00 C
A
3 – Planning
iSCSI/Gigabit Ethernet Performance
Bandwidth
Bandwidth measures the amount of data transmitted over a channel or network. A
1-Gbps/2-Gbps FC port can transmit or receive at nominal rates of 1- or 2-Gbps,
depending on the device to which it is connected. This corresponds to actual
bandwidth values of 106 MB and 212 MB, respectively. WAN data rates range
from 1.5 megabits per second (T1) to greater than 600 megabits per second
(OC-12)
Latency
Latency measures how long a transaction takes to travel through the router or
over a communication link.
iSCSI/Gigabit Ethernet Performance
The SANbox 6142 router supports Ethernet service at transmission rates of
1000-, 100- or 10-Mbps with a MTU size of 1500 or 9000 (jumbo frames). Related
performance characteristics include the following:
„
Distance
„
Bandwidth
„
Latency
Distance
Consider the physical distance between routers. This is usually measured in
round-trip delay. Round-trip delay ranges anywhere from less than 1 millisecond
to as great as 250 milliseconds.
Performance Tuning
Properly configuring the router maximizes its performance. Knowing the round-trip
delay (distance) between routers and the WAN effective data rate (connection
type) allows the routers to be tuned for optimal performance. The following tables
provide TCP Window Scaling Factor and Window Size settings for specific WAN
environments. A table is provided for each connection type.
Table 3-1. T1 / DS-1 – 1.554 Mbits/Sec
FI0054601-00 C
Round Trip delay
(ms)
Total Window Size
(bytes)
Scaling Factor
250
64 K
1
100
32 K
0
50
32 K
0
3-3
S
3 – Planning
Performance Tuning
Table 3-1. T1 / DS-1 – 1.554 Mbits/Sec
Round Trip delay
(ms)
Total Window Size
(bytes)
Scaling Factor
25
32 K
0
20
32 K
0
15
32 K
0
10
32 K
0
5
32 K
0
2.5
32 K
0
1 or less
32 K
0
Table 3-2. T3 / DS-3 – 45 Mbits/Sec
Round Trip Delay
(ms)
Total Window Size
(bytes)
Scaling Factor
250
1 MB
5
100
512 K
4
50
256 K
3
25
128 K
2
20
128 K
2
15
64-128 K
1 or 2
10
64 K
1
5
32 K
0
2.5
32 K
0
1 or less
32 K
0
Table 3-3. DS-5 – 400 Mbits/Sec
3-4
Round Trip Delay
(ms)
Total Window Size
(bytes)
Scaling Factor
250
1 MB
5
100
1 MB
5
FI0054601-00 C
A
3 – Planning
Performance Tuning
Table 3-3. DS-5 – 400 Mbits/Sec (Continued)
Round Trip Delay
(ms)
Total Window Size
(bytes)
Scaling Factor
50
1 MB
5
25
1 MB
5
20
1 MB
5
15
1 MB
5
10
512 K
4
5
256 K
3
2.5
128 K
2
1 or less
64 K
1
Table 3-4. OC-1 – 50 Mbits/Sec
FI0054601-00 C
Round Trip Delay
(ms)
Total Window Size
(bytes)
Scaling Factor
250
1 MB
5
100
512 K
4
50
256 K
3
25
128 K
2
20
128 K
2
15
64-128 K
1 or 2
10
64 K
1
5
32 K
0
2.5
32 K
0
1 or less
32 K
0
3-5
S
3 – Planning
Performance Tuning
Table 3-5. OC-3 – 150 Mbits/Sec
Round Trip Delay
(ms)
Total Window Size
(bytes)
Scaling Factor
250
1 MB
5
100
1 MB
5
50
1 MB
5
25
512 K
4
20
512 K
4
15
256 K
3
10
256 K
3
5
128 K
2
2.5
64 K
1
1 or less
32 K
0
Table 3-6. OC-12 and Above – 621 Mbits/Sec
3-6
Round Trip Delay
(ms)
Total Window Size
(bytes)
Scaling Factor
250
1 MB
5
100
1 MB
5
50
1 MB
5
25
1 MB
5
20
1 MB
5
15
1 MB
5
10
1 MB
5
5
512 K
4
2.5
256 K
3
1 or less
64 K
1
FI0054601-00 C
A
3 – Planning
Topology
Topology
The SANbox 6142 supports two distinct topologies: interconnecting local SANs
(see Figure 3-1) and interconnecting remote SANs (see Figure 3-2).
Figure 3-1 LAN Topology - Local SAN Interconnect
Figure 3-2 WAN Topology - Remote SAN Interconnect
FI0054601-00 C
3-7
S
3 – Planning
Fibre Channel Switch Ports and Zoning Requirements
Fibre Channel Switch Ports and Zoning
Requirements
The SANbox 6142 FC ports are configured as loop ports. Therefore, the FC
switch port, (where SANbox 6142 FC port is connected) must be configured to
support a loop topology such as fibre loop port (FL-Port) or generic port (G-Port).
The SANbox 6142 uses its local FC ports for discovering local FC devices in the
SAN.
We recommend that any FC switch connected to the SANbox 6142 use Fibre
Channel World Wide Port name (WWPN) based zoning. This requires adding the
router’s FC world wide port names (WWPN) in all local switch zones and the
remote router’s FC WWPNs in all remote switch zones.
Multiple Routers
By connecting multiple routers between your Fibre Channel SANs and iSCSI
SANs, you can eliminate any router as a single point of failure.
Management
The SANsurfer Router Manager application and CLI execute on a management
workstation that enables you to configure, control, and maintain the router.
Support platforms include Windows, Solaris, and Linux.
The router supports the following management interfaces:
„
SANsurfer Router Manager – Graphical user interface application, which
executes on a management workstation (see Section 7)
„
Command line interface (CLI) – Executes on the router and is accessed via
telnet or the serial port (see Appendix A)
„
SNMP – Provides router status, traps, and alerts (see Appendix D)
Recovery
It is prudent to have a recovery process in case a router fails. Consider the
following when developing a router recovery process:
„
3-8
Save all firmware image files (updates) in a safe, well-know place, because
you may:
„
Want to revert to a previous firmware version
„
Need the firmware image when replacing a router
„
Need the firmware image when adding a router to your site
FI0054601-00 C
A
3 – Planning
Services
„
„
Save the router’s configuration (as a new file) after every configuration
change, because you may:
„
Want to revert to a previous configuration
„
Need to configure a replacement router
Save the router’s mappings (as a new file) after every mapping change,
because you may:
„
Want to revert to a previous mapping
„
Need to map a replacement router
„
Want to duplicate the mapping on a second router (for backup)
Services
You can configure your router to suit the demands of your environment using a
variety of router services. Familiarize yourself with the following router services
and determine which ones you need:
„
Telnet – Enables router management over a telnet connection.
„
Router management – Provides for out-of-band router management using
the SANsurfer Router Manager.
„
Simple network management protocol (SNMP) – Provides monitoring of
the router using third-party applications that use SNMP.
„
Network time protocol (NTP) – Provides for synchronizing the router and
the workstation dates and times with an NTP server. NTP is disabled (and
not configured) by default.
„
File transfer protocol (FTP) – Provides for transferring files rapidly
between the workstation and router using FTP.
Security
Passwords provide router security. The SANsurfer Router Manager uses a default
password. Once connected, the SANsurfer Router Manager prompts for a
password whenever a user attempts to change a setting.
The CLI interface requires a username and password to start. CLI must be in an
admin session to perform any set operations. An admin session requires a
password.
Once logged on, you can change the password using the application’s security
features.
FI0054601-00 C
3-9
S
3 – Planning
Security
Notes
3-10
FI0054601-00 C
4
Installation
This section describes how to install and configure a SANbox 6142 router. It also
includes firmware installation instructions. This includes the following topics:
„
Site Requirements (this page)
„
SANbox 6142 Router Installation (see page 4-2)
„
Firmware Installation (see page 4-11)
Site Requirements
The requirements in the following sections must be met when installing a SANbox
6142 router:
„
Management Workstation (this page)
„
Power Requirements (see page 4-2)
„
Environmental Conditions (see page 4-2)
Management Workstation
The management workstation running the SANsurfer iSCSI/FC Router Manager
must meet the requirements listed in Table 4-1.
Table 4-1. Management Workstation Requirements
Item
Operating system
Description
One of the following:
„ Windows® 2000/2003/XP
„ Solaris 8/9/10
„ Linux® Red Hat EL 3.x
„ SuSE® Linux 9.0 Enterprise
„ Mac OS® X 10.3
FI0054601-00 C
Memory
256 MB or more
Disk space
150 MB per installation
4-1
S
4 – Installation
SANbox 6142 Router Installation
Table 4-1. Management Workstation Requirements
Item
Description
Processor
500 MHz or faster
Hardware
CD-ROM drive, RJ-45 Ethernet port, RS-232
serial port (optional)
Internet browser
One of the following:
„ Microsoft Internet Explorer 5.0 and later
„ Netscape Navigator® 4.72 and later
„ Mozilla® 1.02 and later
„ Safari™
„ Java 2 runtime environment to support the web
applet
Power Requirements
Power requirements for the SANbox 6142 router are 0.5 Amps at 100-125 VAC,
50 Hz to 60 Hz or 0.25 Amps at 200-240 VAC, 50 Hz to 60 Hz.
Environmental Conditions
Consider the factors that affect the climate in your facility, such as equipment heat
dissipation and ventilation. The router requires the following operating conditions:
„
Operating temperature range – 5–40°C (41–104°F)
„
Relative humidity – 15–90 percent, non-condensing
SANbox 6142 Router Installation
Prior to installing the router, unpack the router and accessories. The SANbox
6142 router is shipped with the following components, shown in Figure 4-1:
4-2
„
Power cord.
„
Adapter (RJ45 to DB9F) for connecting the router’s serial port to a
workstation used for configuring and managing the router. A standard Cat5
Ethernet cable is required (not supplied) to connect the adapter to the router.
The adapter connects directly to the workstation’s serial (COM) port.
FI0054601-00 C
A
4 – Installation
SANbox 6142 Router Installation
Figure 4-1 SANbox 6142 Router and Accessories
To install the SANbox 6142 router:
1.
Complete the pre-installation checklist (see page 4-4).
2.
Mount the router (see page 4-4).
3.
Install the transceivers (see page 4-5).
4.
Connect the management workstation to the router (see page 4-5).
5.
Configure the management workstation (see page 4-5).
6.
Install the management application (see page 4-7).
7.
Start the management application (see page 4-8).
8.
Connect the router to AC power (see page 4-9).
9.
Configure the router (see page 4-10).
10.
Cable FC and iSCSI devices to the router (see page 4-11).
FI0054601-00 C
4-3
S
4 – Installation
SANbox 6142 Router Installation
Pre-installation Check List
During the initial configuration process, the system prompts you for the
parameters listed in Table 4-2. Fill out the table before installation to expedite the
configuration process.
Table 4-2. Pre-installation Checklist
Symbolic name of this router
Management port IP address
(if not using DHCP)
Management port subnet mask (if not
using DHCP)
Management port gateway IP address (if
not using DHCP)
iSCSI Port 1 (GE-1) IP address
iSCSI Port 1 (GE-1) subnet mask
iSCSI Port 1 (GE-1) gateway IP address
iSCSI Port 1 (GE-1) iSNSa IP address
iSCSI Port 2 (GE-2) IP address
iSCSI Port 2 (GE-2) subnet mask
iSCSI Port 2 (GE-2) gateway IP address
iSCSI Port 2 (GE-2) iSNS IP address
a
Internet Storage Name Service
Mount the Router
You can place the router on a flat surface or mount it in a standard 19-inch
Electronic Industries Association (EIA) rack. See the product specification for
weight and dimensions. Rack mounting requires a QLogic rack mounting kit (Part
No. ISR614X-RACKKIT). Contact QLogic for more information.
If you mount the router in a closed or multi-unit rack assembly, make sure that the
operating temperature inside the rack enclosure does not exceed the maximum
rated ambient temperature for the router.
4-4
FI0054601-00 C
A
4 – Installation
SANbox 6142 Router Installation
Install the Transceivers
The router supports a variety of SFP transceivers. To install a transceiver, insert
the transceiver into the port and gently press until it snaps in place. To remove a
transceiver, gently press the transceiver into the port to release tension, then pull
the release tab or lever and remove the transceiver. Different transceiver
manufactures have different release mechanisms. Consult the documentation of
your transceiver.
NOTE:
The transceiver fits only one way. If the transceiver does not install under
gentle pressure, flip it over and try again.
Connect the Management Workstation to the Router
You can manage the router using the SANsurfer iSCSI/FC Router Manager or the
command line interface (CLI). SANsurfer iSCSI/FC Router Manager requires an
Ethernet connection to the router. The CLI can use an Ethernet connection or a
serial connection. Choose the router management method, then connect the
management workstation to the router in one of the following ways:
„
Indirect Ethernet connection from the management workstation to the router
RJ-45 connector through an Ethernet switch or hub. This requires a 10/100
Base-T straight-through cable.
„
Direct Ethernet connection from the management workstation to the router
RJ-45 Ethernet connector. This requires a 10/100 Base-T crossover cable.
„
Serial port connection from the management workstation to the router
RS-232 serial port connector. This requires a 10/100 Base-T
straight-through cable and an RJ45-to-DB9F adapter (included with the
router).
Configure the Management Workstation
The router comes from the factory with a default IP address (10.0.0.1). Prior to
product installation, follow the procedures based on your configuration method:
„
If you plan to configure the router through the management Ethernet port
(using the SANsurfer GUI or CLI via telnet), you must initially configure the
workstation as described in Setting the Workstation IP Address on page 4-6.
„
If you plan to configure the router using the management COM port,
configure the workstation as described in Configuring the Workstation Serial
Port on page 4-6.
FI0054601-00 C
4-5
S
4 – Installation
SANbox 6142 Router Installation
Setting the Workstation IP Address
The IP address of a new router is 10.0.0.1. To ensure that your workstation is
configured to communicate with the 10.0.0 subnet, refer to the following
instructions for your workstation:
„
Steps for different versions of Windows vary. For a Windows 2000
workstation, do the following:
a.
From the Windows Start menu, select Settings>Control
Panel>Network and Dial-up Connections.
b.
Click Make New Connection.
c.
Click Connect to a private network through the Internet, then click
Next.
d.
Enter 10.0.0.253 for the IP address.
„
For different versions of Windows, consult the Windows Help files.
„
For Linux or Solaris workstation, open a command window and enter the
following command, where <interface> is your interface name:
ifconfig <interface> ipaddress 10.0.0.253 netmask
255.255.255.0 up
Configuring the Workstation Serial Port
To configure the workstation serial port:
1.
Connect the cable with RJ45 to DB9F adapter from a COM port on the
management workstation to the serial port on the router.
2.
Configure the workstation serial port according to your platform. These steps
may vary according to the version of Windows you use:
„
4-6
For Windows:
a.
Open the HyperTerminal application. From the Windows Start
menu, select Programs>
Accessories>HyperTerminal>HyperTerminal.
b.
Enter a name for the router connection, choose an icon in the
Connection Description window, then click OK.
c.
Enter the following COM Port settings in the COM Properties
window and click OK.
Bits per second – 115200
Data Bits – 8
Parity – None
Stop Bits – 1
Flow Control – None
FI0054601-00 C
A
4 – Installation
SANbox 6142 Router Installation
„
„
3.
For Linux:
a.
Set up minicom to use the serial port. Create or modify the
/etc/minirs.dfl file with the following content:
pr portdev/ttyS0
pu minit
pu mreset
pu mhangup
pr portdev/ttyS0 specifies port 0 on the workstation.
Choose the pr setting to match the workstation port to which you
connected the router.
b.
Verify that all users have permission to run minicom. Review the
/etc/minicom.users file and confirm that the line ALL exists
or that there are specific user entries.
For Solaris – Modify the /etc/remote file to include the following
lines. /dev/term/a refers to serial port a. Choose the “dv” setting to
match the workstation port to which you connected the router.
SANbox:
\:dv=/dev/term/a:br#115200:el=^C^S^Q^U^D:ie=%$:oe=^
D:
Connect the router to the power (see page 4-9).
Install SANsurfer iSCSI/FC Router Manager
You can manage the router using the SANsurfer iSCSI/FC Router Manager
application. The following sections describe how to install the application on either
a Windows or Linux workstation. See Section 7 for information on how to use
SANsurfer iSCSI/FC Router Manager.
Windows Installation
Perform the following steps to install the SANsurfer iSCSI/FC Router Manager
application from the QLogic website to a PC workstation:
1.
Close all programs currently running.
2.
Go to the QLogic download site:
http://support.qlogic.com/support/drivers_software.aspx
3.
Select the Intelligent Storage Routers icon.
4.
Select SANbox 6142 in the product selection window and click Go.
5.
Under the product name column, select the link to the SANsurfer Router
Manager for your operating system.
6.
Read the license agreement and click Agree.
7.
Follow the system prompts to uncompress and install the application.
FI0054601-00 C
4-7
4 – Installation
SANbox 6142 Router Installation
S
Linux Installation
Perform the following steps to install the SANsurfer iSCSI/FC Router Manager
application from the QLogic website to a Linux workstation:
1.
Go to the QLogic download site:
http://support.qlogic.com/support/drivers_software.aspx
2.
Select the Intelligent Storage Routers icon.
3.
Select SANbox 6142 in the product selection window and click Go.
4.
Under the product name column, select the link to the SANsurfer Router
Manager for your operating system.
5.
Read the license agreement and click Agree.
6.
Save the file to your local system.
7.
Uncompress the downloaded file and execute the Linux_x.xx.bin install
program.
8.
Follow the installation instructions.
Start SANsurfer iSCSI/FC Router Manager
For Windows, double-click the SANsurfer iSCSI/FC Router Manager shortcut, or
select SANsurfer iSCSI/FC Router Manager from the Start menu, depending on
how you installed the SANsurfer iSCSI/FC Router Manager application. From a
command line, you can enter the following command:
<install_directory>SANsurfer_Router_Manager.exe
For Linux, enter the following command:
<install_directory>./SANsurfer_Router_Manager
4-8
FI0054601-00 C
A
4 – Installation
SANbox 6142 Router Installation
Connect the Router to AC Power
WARNING!!
This product is supplied with a 3-wire power cable and plug for the user’s
safety. Use this power cable in conjunction with a properly grounded outlet
to avoid electrical shock. An electrical outlet that is not correctly wired could
place hazardous voltage on metal parts of the router chassis. It is the
customer’s responsibility to ensure that the outlet is correctly wired and
grounded to prevent electrical shock.
You may require a different power cable in some countries because the plug
on the cable supplied with the equipment will not fit your electrical outlet. In
this case, you must supply your own power cable. The cable must meet the
following requirements:
„ For 125 Volt electrical service – the cable must be rated at 10 Amps and
be approved by UL and CSA.
„ For 250 Volt electrical service – the cable must be rated at 10 Amps,
meet requirements of H05VV-F, and be approved by VDE, SEMKO, and
DEMKO.
To power up the router, connect the power cord to the power receptacle on the
router chassis and to a grounded AC outlet. The router responds in the following
sequence:
1.
The chassis LEDs (input power, heartbeat, system fault) light up, then all
port LEDs light up.
2.
After a couple of seconds the heartbeat and system fault LEDs go off, while
the input power LED stays on. The router is executing the POST.
3.
The POST completes after about 45 seconds and the heartbeat LED starts
flashing at a one second rate. If an error has occurred, the System Fault
LED will blink a pattern that indicates the fault reason. For more information
about error blink patterns, see page 5-3.
FI0054601-00 C
4-9
S
4 – Installation
SANbox 6142 Router Installation
Configure the Router
You can configure the router using the SANsurfer iSCSI/FC Router Manager
application or the command line interface (CLI).
The SANsurfer Router Manager provides a Configuration Wizard you can use to
configure the GE ports. If either of the router’s GE ports have not been configured
(IP address is 0.0.0.0), the Configuration Wizard starts automatically when the
SANsurfer first connects with the router. The system uses the information
collected in Table 4-2.
To configure the router using the command line interface:
1.
Open a command window according to the type of workstation and
connection:
„
Ethernet (all platforms) – Open a telnet session with the default router
IP address and log in to the router with the default account name and
password (guest/password).
telnet 10.0.0.1
username – guest
password – ********
„
Serial – On Windows, open the HyperTerminal application. The next
few steps may vary according to the version of Windows you use.
„
2.
4-10
a.
From the Windows Start menu, select
Programs>Accessories>HyperTerminal>HyperTerminal.
b.
Select the connection you created earlier and click OK.
Serial – On Linux, open a command window and enter the following
command:
minicom
Open an admin session and enter the commands to setup both iSCSI ports
and the management interface. See Appendix A for command descriptions.
QRouter #> admin start
Password – ******
QRouter (admin) #> set mgmt
………………………
QRouter (admin) #> set iscsi 1
………………………
QRouter (admin) #> set iscsi 2
………………………
FI0054601-00 C
A
4 – Installation
Firmware Installation
Cable Devices to the Router
Connect cables to the SFP transceivers and their corresponding devices. Devices
can have small form-factor pluggable (SFP) or small form-factor (SFF)
transceivers or gigabit interface converters (GBIC). Lucent (LC)-type duplex fiber
optic cable connectors are designed for SFP transceivers, while
Subscriber-connector (SC)-type connectors are designed for GBICs. Choose the
fiber optic cable with the connector combination that matches the device you are
connecting to the router.
Firmware Installation
The router comes with current firmware installed. You can upgrade the firmware
from the management workstation as new firmware becomes available. You can
use the SANsurfer iSCSI/FC Router Manager application or the CLI to install new
firmware.
WARNING!!
Installing new firmware disrupts the router connectivity since you must
reboot the router to activate the new firmware. The reboot may result in the
transfer of incorrect data between devices connected to the router. QLogic
recommends that you suspend activity on the interfaces before activating
the new firmware.
Using SANsurfer iSCSI/FC Router Manager to Install
Firmware
To install firmware using the SANsurfer iSCSI/FC Router Manager:
1.
Double-click the desired router in the topology display.
2.
In the Firmware Upload window, click Select to browse for and select the
firmware file you want to upload.
3.
Click Start to begin the firmware load process. A message displays a
warning that the router will be reset to activate the firmware.
4.
Click OK to continue firmware installation or click the Cancel button to
cancel the firmware installation.
FI0054601-00 C
4-11
S
4 – Installation
Firmware Installation
Using the CLI to Install Firmware
To use the CLI to install the firmware, transfer the firmware image file from a
workstation to the router. Then use the CLI image unpack command to install the
new firmware image:
4-12
1.
At the workstation prompt, use the ftp command to go to the location on the
router where you want to transfer the firmware image. For example:
C:\fwImage>ftp 172.17.137.190
Connected to 172.17.137.190.
220 (none) FTP server (GNU inetutils 1.4.2) ready.
2.
Enter your username and password. For example:
User (172.17.137.190:(none)) – ftp
331 Guest login ok, type your name as password.
Password – ftp
230 Guest login ok, access restrictions apply.
3.
At the ftp prompt, type BIN to set binary mode. For example:
ftp> bin
200 Type set to I.
4.
Use the put command to transfer the firmware image file from the
workstation to the router. For example:
ftp> put isr-6142-2_2_0_x.bin
200 PORT command successful.
150 Opening BINARY mode data connection for
'isr-6142-2_2_0_x.bin'.
226 Transfer complete.
ftp – 4822816 bytes sent in 0.41Seconds
11878.86Kbytes/sec.
5.
Type quit. The firmware image has been transferred to the router.
6.
Log on to the router as an administrator.
(none) login – guest
Password – password
******************************************************
*
*
*
QLogic Router Command Line Interface (QRCLI) *
* *
******************************************************
QRouter#> admin start
Password
– config
QRouter (admin) #>
FI0054601-00 C
A
4 – Installation
Firmware Installation
7.
Type the following command from the router, where x stands for the
firmware image name:
image unpack isr-6142-2_2_0_x.bin
The following message displays:
Unpack Completed. Please reboot the system for FW to
take affect.
8.
Type reboot. The following message displays:
Are you sure you want to reboot the System (y/n):
9.
Type y to reboot the system.
FI0054601-00 C
4-13
4 – Installation
Firmware Installation
S
Notes
4-14
FI0054601-00 C
5
Diagnostics and
Troubleshooting
Diagnostic information about the router is available through the chassis LEDs and
the port LEDs. Diagnostic information is also available through the SANsurfer
iSCSI/FC Router Manager and CLI event logs and error displays. This section
provides the following diagnostic information:
„
Chassis Diagnostics (this page)
„
Power-On Self-Test Diagnostics (see page 5-2)
„
LED Blink Patterns (see page 5-3)
This section also describes how to use maintenance mode to recover a disabled
router (see page 5-5).
Chassis Diagnostics
The chassis LEDs show chassis diagnostics as shown in Figure 5-1.
Figure 5-1 Chassis Diagnostic LEDs
This section describes the following conditions:
„
Input Power LED is Off (see page 5-2)
„
System Fault LED is On (see page 5-2)
FI0054601-00 C
5-1
5 – Diagnostics and Troubleshooting
Power-On Self-Test Diagnostics
S
Input Power LED is Off
The input power LED lights up to show that the router logic circuitry is receiving
proper voltages. If the input power LED is off, do the following:
„
„
„
Inspect power cord and connectors. Is the cord unplugged? Is the cord or
connector damaged?
„
Yes – Make necessary corrections or repairs. If the condition remains,
continue.
„
No – Continue.
Inspect AC power source. Is the power source delivering the proper voltage?
„
Yes – Continue.
„
No – Make the necessary repairs. If the condition remains, continue.
Replace the router.
System Fault LED is On
The System fault LED will blink a specific pattern to indicate the problem. If the system
fault LED lights up, take necessary actions (see page 5-3).
Power-On Self-Test Diagnostics
The router performs a series of tests as part of its power-on procedure. The POST
diagnostic program performs the following tests:
5-2
„
Memory
„
FLASH validation
„
PCI device discovery
„
Management Ethernet port
FI0054601-00 C
A
5 – Diagnostics and Troubleshooting
LED Blink Patterns
LED Blink Patterns
The Heartbeat and System Fault LEDs show the operational status of the router.
When the POST completes with no errors, the heartbeat LED will blink once every
second. When the router is in maintenance mode, the Heartbeat and System Fault
LEDs are on continuously.
All other System Fault blink patterns show critical errors. The heartbeat LED shows
an error blink pattern for the conditions listed in Table 5-1.
Table 5-1. System Fault LED Blink Patterns
System Fault LED
Condition
OFF
OK - Operational
3 Blinks, followed by pause
System error
4 Blinks, followed by pause
Management port IP address conflict
5 Blinks, followed by pause
Over temperature
Heartbeat Blink Pattern
A blink pattern on the Heartbeat LED of one second ON followed by one second
OFF means that the router is operating normally. The Heartbeat LED shows this
pattern when the router firmware is operational.
System Error Blink Pattern
The System Fault LED generates a three-blink pattern (once per second) followed
by a two second pause to indicate a system error.
FI0054601-00 C
5-3
5 – Diagnostics and Troubleshooting
LED Blink Patterns
S
Management Port IP Address Conflict Blink Pattern
The System Fault LED generates a four-blink pattern (once per second) followed
by a two second pause when the router detects an IP address conflict on the
management Ethernet port.
You can clear the IP address conflict blinking using the CLI or SANsurfer Router
Manager. Use the beacon OFF function.
Over-Temperature Blink Pattern
The System Fault LED generates a five-blink pattern (once per second) followed
by a two second pause when the router is in an over-temperature condition. That
is, the air temperature inside the router is over the failure temperature of 70°C
(158°F).
If the system alert LED shows the over temperature blink pattern, do the following:
„
„
5-4
Inspect the chassis air vents. Are the intake and exhaust vents clear?
„
Yes – Continue
„
No – Remove any debris from the fan intake and exhaust if necessary.
If the condition remains, continue.
Consider the ambient air temperature near the router and clearance around
the router. Make necessary corrections. If the condition remains, open a
command line window and log on to the router. Enter the Shutdown
command, then power down the router. Contact your authorized
maintenance provider.
FI0054601-00 C
A
5 – Diagnostics and Troubleshooting
Recovering a Router
Recovering a Router
You may have to recover a router for one of the following reasons:
„
The password was changed and has been forgotten.
„
The router’s management IP address is unknown.
To recover the router’s password, reset the password to the default by using the
maintenance button (see page 2-8).
You can recover the router’s IP address using either of the following methods:
„
Connect to the serial console port (see page 2-13), then use the CLI Set
Mgmt command reconfigure the management port (see page A-44).
„
Use the maintenance button to reset the management port’s IP to the factory
default of 10.0.0.1 (see page 2-8).
FI0054601-00 C
5-5
5 – Diagnostics and Troubleshooting
Recovering a Router
S
Notes
5-6
FI0054601-00 C
6
Removal/Replacement
This section describes the removal and replacement procedures for the following
field replaceable units (FRU):
„
SFP transceivers
„
The router (see page 6-2)
SFP Transceiver Removal and Replacement
You can remove and replace the SFP transceivers while the router is operating
without damaging the router or the transceiver. However, doing so will interrupt
transmission on the affected port until the transceiver is installed.
„
To remove a transceiver, gently press the transceiver into the port to release
the tension, then pull the release tab or lever and remove the transceiver.
Different transceiver manufactures have different release mechanisms.
Consult the documentation for your transceiver.
„
To install a transceiver, insert the transceiver into the port and gently press
until it snaps in place.
NOTE:
The SFP transceiver will fit only one way. If the SFP does not install under
gentle pressure, flip it over and try again.
FI0054601-00 C
6-1
6 – Removal/Replacement
Router Removal and Replacement
S
Router Removal and Replacement
Before you can remove and replace the router, you must turn off the power to the
router and disconnect its power cable. The router will lose all the Fibre Channel
and iSCSI connections.
Removal
To remove and replace a router, perform the following steps, as applicable:
1.
Make sure all traffic (I/O operations to the router) subsides at the iSCSI
initiator systems.
2.
Save the configuration data of the router using the CLI FRU command (see
page A-13).
3.
Power down the router.
4.
Disconnect the power cable.
5.
Label all the cables so that they can be connected to the same ports on the
replacement router.
6.
Remove all the Fibre Channel and Ethernet cables.
7.
Remove the router from the enclosure where it is mounted.
Replacement
Before replacing a router, you must first remove the previously installed router (as
described above).
To install a replacement router:
1.
Mount the router in the enclosure.
2.
Reconnect the Fibre Channel and Ethernet cables to the ports where they
were previously connected.
3.
Connect the power cable to the router.
4.
Using a management station, configure the management port IP address
(see page 4-2).
5.
Using a management workstation, restore the saved configuration or
reconfigure the router as desired (see page A-13).
The replacement router should now be operational.
6-2
FI0054601-00 C
7
SANsurfer iSCSI/FC Router
Manager
Introduction
The SANbox 6142 management application is a graphical user interface
consisting of menus, buttons, and windows that you can use to manage SANbox
6142s from a workstation on Linux® and Windows® platforms. You can view and
change network, port, security, and mapping configuration for one or more
SANbox 6142s. The application displays the most current system information.
The SANsurfer iSCSI/FC Router Manager consists of a menu bar, a tool bar, a
system tree, and information/status/data windows and tabs, as illustrated in
Figure 7-1 and described in Table 7-1.
FI0054601-00 C
7-1
S
7 – SANsurfer iSCSI/FC Router Manager
Introduction
Figure 7-1 SANsurfer Router Manager Main Window
Table 7-1. SANsurfer Router Manager Main Window Sections
Item
7-2
Description
Menu Bar
The menu bar provides access to system functions and Wizards.
Tool Bar
The tool bar buttons provide quick access to
the common application functions: Connect,
View Logs, and Refresh.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Menu Bar
Table 7-1. SANsurfer Router Manager Main Window Sections
Item
Description
System Tree
Located on the on the left side of the display,
the system tree shows the connected systems
and their components. An entry handle located
to the left of an entry in the tree shows that you
can expand that entry. Click an entry handle or
double-click the entry to expand or collapse a
system tree entry. Click and drag the window
border to re-size the window.
Action Menu
Right-click anywhere on the system tree window to open the action menu. This menu provides a shortcut to actions available elsewhere
in the SANsurfer Router Manager. If you select
an initiator or target (highlighted), then
right-click in the system tree, the action menu
activates the Remove Initiator and Remove
Offline Target selections.
Information, Configuration,
and Status windows
These windows present the corresponding
information, configuration, or status for the window tab you select. Some windows contain a
scroll bar to browse the window contents.Click
and drag the window border to re-size the window.
Window Tabs
The window tab determines what is displayed
in the window.
Menu Bar
Figure 7-2 shows the menu bar options. The following sections describe them.
Figure 7-2 Menu Bar
FI0054601-00 C
7-3
S
7 – SANsurfer iSCSI/FC Router Manager
Menu Bar
File Menu
Figure 7-3 shows the File menu. The following paragraphs describe it.
Figure 7-3 File Menu
„
Save FRU – Saves the router’s configuration and persistent data to a file.
„
Restore FRU – Restores the router’s configuration and persistent data from
a file.
„
Exit – Exits the SANsurfer iSCSI/FC Router Manager.
View Menu
Figure 7-4 shows the View menu. The following paragraph describes it.
Figure 7-4 View Menu
„
View Logs – Opens the window displaying the system logs.
Settings Menu
Figure 7-5 shows the Settings menu. The following paragraph describes it.
Figure 7-5 Settings Menu
„
7-4
Broadcast – Opens the Broadcast Settings window, which allows you to
configure the broadcast options. The workstation sends Broadcast
messages to locate routers within the same IP subnet as the workstation
running the SANsurfer Router Manager application. Figure 7-6 shows the
Broadcast Settings dialog box. The following paragraphs describe its
options.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Menu Bar
Figure 7-6 Broadcast Settings Menu
„
Enable Broadcast – Enables broadcast messages sent to locate routers in
the IP subnet.
„
Enable Auto Connect – Enables the SANsurfer Router Manager to
automatically connect with routers discovered by the broadcast.
„
Broadcast Interval – Lets you enter the time interval at which the
SANsurfer Router Manager sends broadcast messages to locate routers
within the same IP subnet as the workstation.
Wizards Menu
Figure 7-7 shows the Wizards menu. The following paragraphs describe it.
Figure 7-7 Wizards Menu
„
Configuration Wizard – Launches the iSCSI Port Configuration wizard,
which allows you to configure the IP address and other parameters for an
iSCSI port (see page 7-44).
„
Add Initiator Wizard – Launches the iSCSI Add Initiator wizard, which
allows you to configure the IP address and other parameters for an iSCSI
initiator (see page 7-49).
„
FW Update Wizard – Launches the Firmware Update wizard, which allows
you to update the SANbox 6142 router’s firmware image. You can select the
firmware image from a menu that allows browsing (see page 7-51).
FI0054601-00 C
7-5
7 – SANsurfer iSCSI/FC Router Manager
Menu Bar
7-6
S
„
Map Local Initiator/Target Wizard – Launches the Map Local wizard,
which allows you to map a local initiator to a local target (see page 7-55).
„
Unmap Local Initiator/Target Wizard – Launches the Unmap Local wizard,
which allows you to delete a local initiator from a local target mapping (see
page 7-63).
„
Add Remote Router Wizard – Launches the Add Remote Router wizard,
which allows you to assign local router to a remote router as peers (see
page 7-68).
„
Remove Remote Router Wizard – Launches the Remove Remote Router
wizard, which allows you to remove a local-to-remote router peer
assignment (see page 7-72).
„
Map Remote Initiator/Target Wizard – Launches the Map Remote wizard,
which allows you to map an initiator to a target device, one of which is on a
remoter router (see page 7-75).
„
Unmap Remote Initiator/Target Wizard – Launches the Unmap Remote
wizard, which allows you to delete an initiator-to-target device mapping (see
page 7-81).
„
Discover iSCSI Target – Launches the Discover iSCSI Target wizard, which
allows you to specify the IP address of the iSCSI Target to be discovered.
The target is added to the discovered targets list (see section page 7-84).
„
FCIP Route Add – Launches the (Fiber channel over IP) FCIP Route Add
wizard, which allows you to select – the resources used for the route, the IP
address of the remote FCIP peer, IP parameters, Virtual Lan (VLAN)
support, compression and bandwidth limit (see page 7-86).
„
FCIP Route Remove – Launches the FCIP Route Remove wizard, which
allows you to remove an existing FCIP Route, freeing the resources (FC and
GE ports) used by the route (see page 7-92).
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Tool Bar
Help Menu
Figure 7-8 shows the Help menu. The following paragraphs describe it.
Figure 7-8 Help Menu
Set Browser Location – Allows you to specify the browser that launches when
you view the online help for the SANsurfer iSCSI/FC Router Manager.
Browse Contents – Launches the online help for the SANsurfer iSCSI/FC Router
Manager.
About – Displays the application version information.
Tool Bar
Figure 7-9 shows the tool bar. The following paragraphs describe it.
Figure 7-9 Tool Bar
The tool bar consists of a row of graphical buttons that allow you to perform
common functions – connect, view log files, and refresh the current display. You
can move the tool bar in the display by clicking and dragging the handle at the tool
bar’s left edge.
„
Connect – Adds a SANbox 6142 router to the system tree view.
„
View Logs – Opens a window to display the system log data.
„
Refresh – Updates the display with current information.
FI0054601-00 C
7-7
S
7 – SANsurfer iSCSI/FC Router Manager
Tool Bar
Action Menu
The action menu provides short cuts to actions and wizards available elsewhere
in the SANsurfer iSCSI/FC Router Manager. To open this menu, right-click
anywhere within the router’s node in the system tree window. Figure 7-10
illustrates the action menu and the following paragraphs describe each available
option.
Figure 7-10 Action Menu
7-8
„
Connect – Adds a SANbox 6142 router to the system tree view.
„
Refresh – Updates the display with current information.
„
Disconnect – Disconnects from a SANbox 6142 router, removing it from
the system tree.
„
Reboot – Reboots the SANbox 6142 router.
„
View Logs – Opens the View Logs window.
„
Ping – Initiates a ping from the specified port (management, GE1, or GE2)
to a specified IP address.
„
Map Local Initiator/Target Wizard – Launches the Map Local
Initiator/Target Wizard, which allows you to map a local initiator to a local
target (see page 7-55).
„
Unmap Local Initiator/Target Wizard – Launches the Unmap Local
Initiator/Target Wizard, which allows you to delete a local initiator from a
local target mapping (see page 7-63.)
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Tool Bar
„
Add Remote Router Wizard – Launches the Add Remote Router Wizard,
which allows you to assign local router to a remote router as peers (see
page 7-68).
„
Remove Remote Router Wizard – Launches the Remove Remote Router
Wizard, which allows you to remove a local-to-remote router peer
assignment (see page 7-72).
„
Map Remote Initiator/Target Wizard – Launches the Map Remote
Initiator/Target Wizard, which allows you to map an initiator to a target
device, one of which is on a remoter router (see page 7-75).
„
Unmap Remote Initiator/Target Wizard – Launches the Remote Mapped
Device, which allows you to delete an initiator-to-target device mapping (see
page 7-81).
„
Discover iSCSI Target – Launches the Discover iSCSI Target Wizard,
which allows you to specify the IP address of the iSCSI Target to be
discovered. The target is added to the discovered targets list (see
page 7-84).
„
FCIP Route Add – Launches the FCIP Route Add Wizard wizard, which
allows you to select the resources used for the route, the IP address of the
remote FCIP peer, IP parameters, VLAN support, compression and
bandwidth limit (see page 7-86).
„
FCIP Route Remove – Launches the FCIP Route Remove Wizard wizard,
which allows you to remove an existing FCIP Route freeing the resources
(FC and GE ports) used by the route. (See page 7-92).
„
FW Update Wizard – Launches the FW Update Wizard, which allows you to
update the router’s firmware (see page 7-51).
„
Add Initiator Wizard – Launches the Add Initiator Wizard, which allows you
to enter an iSCSI initiator into the system database (see page 7-49).
„
Remove Initiator – Removes the selected iSCSI initiator. This option is
available only when an initiator is selected (highlighted) in the system tree.
„
Remove Offline Target – Removes the selected offline Fibre Channel
target. This option is available only when an offline FC target is selected
(highlighted) in the system tree.
„
Beacon ON – Turns on the SANbox 6142 router beacon to locate the router
quickly.
„
Beacon OFF – Turns off the SANbox 6142 router beacon.
FI0054601-00 C
7-9
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
System Tree Window
Figure 7-11 shows the system tree window. The following sections described it.
Figure 7-11 System Tree Window
The left most window pane shows the system tree. The system tree includes the
connected SANbox 6142 routers and the following components for each router:
„
FC Ports (see page 7-20)
„
iSCSI Ports (see page 7-23)
„
Discovered iSCSI Initiators (see page 7-31)
„
FC Discovered Targets (see page 7-34)
„
iSCSI Discovered Targets (see page 7-38)
„
FCIP Routes (see page 7-39)
Select a component in the system tree to see component data in the tabbed
pages to the right of the tree (see page 7-11).
7-10
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Figure 7-12 Component Information
Component information displayed for a selected router includes router
information, configuration details, router status, and lists of connected or
discovered devices.
FI0054601-00 C
7-11
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
SANbox 6142 Router
The top of the router tree displays the router system configuration and status. It
contains the following tabs:
„
Information Tab (see page 7-12)
„
SNMP Management Tab (see page 7-17)
„
Features Tab (see page 7-19)
„
Assigned Remote Router Tab (see page 7-19)
„
Topology Tab (see page 7-20)
NOTE:
If your router’s configuration includes a remote router, the router
configuration window includes a tab with the basic information for that router,
as shown in the following example for Assigned Remote Router:1. You can
define additional remote routers using the Add Remote Peer wizard.
Information Tab
The Information tab provides four vertical tabs with icons that identify its content:
Basic Information, Management Information, and NTP Server Information, and
Security. It also contains three buttons: Reboot, FW Load, and Restore Defaults.
Basic Information
Figure 7-13 Basic Information Vertical Tab
The Basic Information tab provides the following parameters:
7-12
„
Product Name – Identifies the router model.
„
Symbolic Name – Lets you to assign a symbolic name to the router.
„
Serial Number – Displays the router’s serial number.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
Hardware Version – Identifies the router hardware version number.
„
Software Version – Identifies the version of firmware loaded on the router.
„
iSCSI Port Count – Identifies the number of iSCSI ports (2).
„
Fibre Channel Port Count – Identifies the number of Fibre Channel ports
(2).
Management Information
Figure 7-14 Management Information Vertical Tab
The Management Information tab provides the following parameters:
„
MAC Address – Displays the management port’s MAC address.
„
Link Status – Displays the management port link status: Link UP or Link
Down.
FI0054601-00 C
7-13
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
IPv4 Management Info – Select this check box to use IPv4 (Internet
Protocol version 4, 32-bit addressing), then use the radio buttons to identify
whether to use either a dynamic or static IP address.
„
„
„
„
7-14
S
IP Address – Displays the management port’s subnet mask.
„
If you selected the Obtain an IP address automatically (DHCP)
radio button, the system obtains the IP address automatically
through DHCP.
„
If you selected the Use the following IP address radio button,
you can configure the IP address.
Subnet Mask – Displays the management port’s subnet mask.
„
If you select the Obtain an IP address automatically (DHCP),
the system obtains the subnet mask automatically through
DHCP.
„
If you selected the Use the following IP address radio button,
you can configure the subnet mask.
Gateway – Displays the IP address of the server acting as a gateway
to your Internet connection.
„
If you select the Obtain an IP address automatically (DHCP),
the system obtains the gateway address automatically through
DHCP.
„
If you selected the Use the following IP address radio button,
you can specify the gateway address.
IPv6 Management Info – Select this check box to use IPv6 (Internet
Protocol version 6, 128-bit addressing), then use the radio buttons to identify
whether to use either a dynamic or static IP address.
„
IPv6 Management Info – Select this check box if you want to use
IPv6, then use the radio buttons to identify whether to use a dynamic
or static IP address.
„
IPv6 Address1 – The first user-assigned IPv6 address to which the
port responds. A value of :: indicates that an IPv6 address has not
been assigned. Although you may modify the IP address in this
window, you will typically set it using the Configuration Wizard.
„
IPv6 Address2 – The second user-assigned IPv6 address to which
the port responds. A value of :: indicates that an IPv6 address has not
been assigned. Although you may modify the IP address in this
window, you will typically set it using the Configuration Wizard.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
IPv6 Default Router – Use this address to set the default router for the
IPv6. The system can also set the IPv6 default router dynamically
depending on your network configuration.
„
IPv6 Local Link – This field contains the IPv6 link local address of the
port. It is not editable.
NOTE:
IPv6 support is available only with hardware version 6 and software version
2.4.0.0 and greater.
„
Set IP Address – After making any IP address changes, click this button to
save your changes.
NTP Server Information
Figure 7-15 NTP Server Information Vertical Tab
The NTP Server Information tab provides the following parameters:
„
NTP Server Radio Buttons – Use these buttons to disable or enable the
use of NTP servers to set the router’s date and time.
„
NTP Server 1 – Displays the IP address of the first NTP server to be queried
by the router when setting its time and date.
FI0054601-00 C
7-15
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
„
NTP Server 2 – Displays the IP address of the second NTP server to be
queried by the router when setting its time and date. This server is used only
if the first NTP server did not respond.
„
NTP Server 3 – Displays the IP address of the third NTP server to be
queried by the router when setting its time and date. This server is used only
if the first and second NTP servers did not respond.
„
NTP Server 4 – Displays the IP address of the fourth NTP server to be
queried by the router when setting its time and date. This server is used only
if the first, second, and third NTP servers did not respond.
„
Set NTP Address – After enabling NTP Servers and setting their IP
addresses, click this button saves any changes made to the NTP server IP
addresses.
Security
Figure 7-16 Security Vertical Tab
The Security tab enables you to set the router’s password. The Security tab
provides the following parameters:
7-16
„
Current Password – You must enter the current password before changing
it.
„
New Password – Enter the new router password.
„
Verify New Password – Verify the password entered in the New Password
field.
„
Apply – Click this button to save the password changes.
„
Clear Fields – Click this button to clear the Current Password, New
Password, and Verify Password fields.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
SNMP Management Tab
The SNMP Management tabbed page consists of two sections: SNMP
Configuration and SNMP Trap Receivers. The Save button saves any SNMP
management changes. For more information, see Appendix D.
Figure 7-17 shows the SNMP Management tabbed page. The following
paragraphs describe it.
Figure 7-17 SNMP Management Tabbed Page
The SNMP Management tab provides two configuration sections:
„
SNMP Configuration
„
SNMP Trap Receivers
SNMP Configuration
The SNMP Configuration section provides the following vendor and SNMP setting
fields:
„
System OID – Displays the system object identifier.
„
System Description – Displays a description of the router location.
FI0054601-00 C
7-17
S
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
Read Community – Enter a password that authorizes an SNMP
management server to read information from the router. This is a write-only
field. The value on the router and the SNMP management server must be
the same. The read community password can be up to 32 characters
excluding #, semicolon (;), and comma (,). The default is public.
„
Trap Community – Enter a password that authorizes an SNMP
management server to receive traps. This is a write-only field. The value on
the router and the SNMP management server must be the same. The trap
community password can be up to 32 characters excluding the number sign
(#), semicolon (;), and comma (,). The default is public.
„
System Location – Specifies the name of the router location. The name can
be up to 64 characters excluding the number sign (#), semicolon (;), and
comma (,).
„
System Contact – Specifies the name of the person to be contacted to
respond to trap events. The name can be up to 64 characters excluding the
number sign (#), semicolon (;), and comma (,).
„
Authentication Traps – Enables or disables the generation of
authentication traps in response to authentication failures.
SNMP Trap Receivers
7-18
„
Enabled – Select this check box next to each trap receiver you want to
configure, then use the following fields to specify its IP address, trap port,
and trap version.
„
IP Protocol – Select the IP protocol version from the drop-down menu: IPv6
Address or IPv4 Address. The IP address field changes to accept the
appropriate format.
„
IP Address – Specifies the IP address to which the SNMP traps are sent. A
maximum of eight trap addresses are supported.
„
Trap Port – Identifies the port number on which the trap is sent. The default
is 162.
„
Trap Version – Specifies the SNMP version (1 or 2) with which to format
traps.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Features Tab
Figure 7-18 shows the Features tabbed page that displays the routers licensed
features and lets you apply additional license features. The following paragraphs
described the page.
Figure 7-18 Features Tabbed Page
„
License Information – Displays a list of the routers licensed features.
„
Add – Initiates the Add Feature wizard.
Assigned Remote Router Tab
If your local router has any remote routers added as peers to its configuration, the
SANbox 6142 router screen includes a tabbed page for each assigned remote
router.
This screen provides the following information about the remote router:
„
Product Name – Identifies the model of the remote router.
„
Symbolic Name – Displays the symbolic name, if one is assigned to the
remote router.
„
Serial Number – Displays the remote router’s serial number.
„
Hardware Version – Identifies the remote router hardware version number.
Starting with version 6, the hardware supports IPv6.
„
Software Version – Identifies the version of firmware loaded on the remote
router. IPv6 requires software version 2.4.0.0 or later.
„
iSCSI Port Count – Identifies the number of iSCSI ports (2).
„
Management IP Address – Displays the IP address of the remote router.
FI0054601-00 C
7-19
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
Topology Tab
Figure 7-19 shows the Topology tabbed page that displays the routers, as shown
in the following example.
Figure 7-19 Topology Tabbed Page
FC Ports
When you select an FC port in the system tree, the system displays the FC Port
Information tabbed page (see Figure 7-20).
Figure 7-20 FC Port Information Tab
7-20
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
FC Port Information Tab
The FC Port Information tab provides the following parameters:
„
Node Name – Displays the world-wide node name (WWNN) assigned to the
FC port.
„
Port Name – Displays the world-wide port name (WWPN) assigned to the
FC port.
„
Port Status – Lets you change the port status: Enabled (online) or
Disabled (offline). After changing the status, click Save. If you choose to
disable the port, a warning message appears, letting you know it will
disconnect one or more ports. Click Yes to disconnect the port, or No to
cancel the changes.
„
Link Status – Displays the link status, either Link Up or Link Down.
„
Port ID – Displays the ID assigned by the FC fabric or AL_PA if the FC port
is connected to a private loop.
„
Actual Connection Mode – Displays the port’s connection mode, either
point-to-point or loop.
„
Actual Data Rate – Displays the port’s operating data rate when online,
either one gigabit per second (1 Gbps) or two gigabits per second (2 Gbps).
FC Port Advanced Configuration Tab
When you select the Advanced Configuration tab for the selected FC port, the
system displays the Advanced Configuration tabbed page (see Figure 7-21).
Figure 7-21 FC Port Advanced Configuration Tab
The FC port Advanced Configuration tab provides the following parameters:
„
Connection Options – Displays the connections. When an FC port is not
part of an FCIP route, it only operates in FC loop mode.
„
Data Rate – Displays a drop-down list that lets you set the data rate: Auto, 1
Gbps, or 2 Gbps. The default is auto. If you change this setting, you must
click Save (at the bottom of the page) for the change to take effect.
FI0054601-00 C
7-21
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
„
Frame Size – Displays a drop-down list that lets you set the frame size:
2048, 1024, or 512 bytes. The default is 2048. If you change this setting, you
must click Save (at the bottom of the page) for the change to take effect.
„
Execution Throttle – Displays a drop-down list that lets you set the
execution throttle: 16, 32, 64, 128, or 256. The default is 64. When you
change this setting, you must click Save (at the bottom of the page) for the
change to take effect.
FC Port Performance Tab
When you select the Performance tab for the selected FC port, the system
displays the Performance tabbed page (see Figure 7-22).
Figure 7-22 FC Port Performance Tab
The FC Port Performance tab displays the following information:
7-22
„
Initiator Read – Shows the initiator’s read performance through the
selected FC port.
„
Initiator Write – Shows the initiator’s write performance through the
selected FC port.
„
Target Read – Shows the target’s read performance through the selected
FC port.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
Target Write – Shows the target’s write performance through the selected
FC port.
iSCSI Ports
When you select an iSCSI port in the system tree, the window displays the
Information, Advanced Configuration, and Statistics tabbed pages to the right of
the tree (see Figure 7-23). These following sections describe these pages.
Figure 7-23 iSCSI Port Tabbed Pages
FI0054601-00 C
7-23
S
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Information Tab
The Information tabbed page consists of three areas: Port Information, iSCSI Port
Network Settings, and iSNS. The following paragraphs describe the information
displayed in these sections.
iSCSI Port Information
The iSCSI Port Information area provides the following parameters:
„
Base Name – Displays the full name assigned to the selected iSCSI port.
„
Link Status – Identifies the port connection status: Link Up or Link
Down.
„
MAC Address – Displays the MAC address assigned to the port. The MAC
address is not changeable.
„
Actual Link Rate – Displays the actual link rate, which can be Unknown,
1000 Mbps, 100 Mbps, or 10 Mbps. If the port's configuration or
connection has changed, the status may not be current. Click the Refresh
icon to display the current status.
„
Programmed Link Rate – The configured data rate for the port. To
configure the data rate, open the drop-down menu and select one of the
following data rates:
„
Auto - Data rate determined by network attachment
„
10 Mbps - 10 megabits per second
„
100 Mbps - 100 megabits per second
„
1000 Mbps - 1000 megabits per second (1 gigabit per second)
When you change this setting, you must click Save (at the bottom of the
page) for the change to take effect.
„
„
7-24
Link Rate Mode – If you selected a specific Programmed Link Rate (not
Auto), you can specify one of these modes:
„
Auto
„
Half Duplex
„
Full Duplex
Flow Control – If you selected a specific Programmed Link Rate (not
Auto), you can enable or disable flow control.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
iSCSI Port Network Settings
„
Port Status – When the port link is up, you can enable or disable the port
using this drop-down list.
„
IPv4 Address – When using an IPv4 address scheme, define the following
fields:
„
FI0054601-00 C
„
IP Address – The IP address to which the port responds. An
un-initialized port has an IP address of all zeros. Although you may
modify the IP address in this window, you will typically set it using the
Configuration Wizard.
„
Subnet Mask – The subnet mask used by the port. Although you may
modify the subnet mask in this window, you will typically set it using the
Configuration Wizard.
„
Gateway – The gateway for the selected port.
„
VLAN – The VLAN configuration: Disabled or Enabled. You can
configure VLAN from this window.
„
VLAN ID – When VLAN is enabled the VLAN ID contains an
identification value in the range 0 to 4094. You can configure VLAN
from this window.
„
Priority – When VLAN is enabled, this field defines the priority
assigned to this VLAN. To set the priority, open the drop-down menu
and select the desired value (between 0 to 7).
IPv6 Address – When using an IPv6 address scheme, define the following
fields:
„
IPv6 Address1 – The first user-assigned IPv6 address to which the
port responds. A value of :: indicates that an IPv6 address has not
been assigned. Although you may modify the IP address in this
window, you will typically set it using the Configuration Wizard.
„
IPv6 Address2 – The second user-assigned IPv6 address to which
the port responds. A value of :: indicates that an IPv6 address has not
been assigned. Although you may modify the IP address in this
window, you will typically set it using the Configuration Wizard.
„
IPv6 Default Router – Use this address to set the default router for the
IPv6. The system can also set the IPv6 default router dynamically
depending on your network configuration.
„
IPv6 Local Link – This field contains the IPv6 link local address of the
port. It is not editable.
„
VLAN IPv6 – The VLAN IPv6 configuration: Disabled or Enabled. You
can configure VLAN from this window.
7-25
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
„
VLAN ID IPv6 – When VLAN IPv6 is enabled the VLAN ID IPv6
contains an identification value in the range 0 to 4094. You can
configure VLAN from this window.
„
Priority IPv6 – When VLAN IPv6 is enabled, this field defines the
priority assigned to this VLAN IPv6. To set the priority, open the
drop-down menu and select the desired value (between 0 to 7).
NOTE:
IPv6 support is available only with hardware version 6 and greater and
software version 2.4.0.0 and greater.
„
7-26
Enable iSNS – This check box enables or disables iSNS support. Select the
check box to enable this option; clear the check box to disable it.
„
IP Server – This drop-down box lets you choose the IP address
version assigned to the IP server. The following examples show the IP
address fields that open when you choose one of these options.
„
Server IP Address – The IP address assigned to the iSNS server to
which this port will communicate. You can configure this IP address
when iSNS is enabled. Note the different formats provided for the two
different IP address version.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Advanced Configuration Tab
The Advanced Configuration tabbed page allows you to configure the router’s port
parameters, security settings, and CHAP settings. The information displayed in
these sections is illustrated in Figure 7-24 and described in the following
paragraphs.
Figure 7-24 Advanced Configuration Tabbed Page
The iSCSI Port Advanced Configuration tab provides the following parameters:
„
iSCSI Port Number – Identifies the iSCSI port number (1 or 2).
„
Enable TCP Window Scaling – When you change this setting, you must
enter the Scale Factor (valid values are 0–5), then click Save (at the bottom
of the page) for the change to take effect.
„
TCP Max Window Size – Enables you to set the TCP maximum window
size. To change the setting, open the drop-down menu and select one of the
options: 8192, 16384, or 32768.
FI0054601-00 C
7-27
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
7-28
S
„
Target TCP Port Number – Identifies the TCP port number the router uses
to receive iSCSI target commands. The iSCSI community uses TCP port
number 3260 by default any change to this TCP port number requires a
corresponding change in all iSCSI initiators connecting to this iSCSI target
port. When you change the target TCP port number, you must click Save (at
the bottom of the page) for the change to take effect.
„
Jumbo Frame – Enables or disables router jumbo frame size as the
maximum transfer unit (MTU). Disabling this option sets the port to support
1500 byte MTU. Enabling this option sets the port to support 9000 bytes
MTU. To change this setting, select Enabled or Disabled from the
drop-down menu. When you change this setting, you must click Save (at the
bottom of the page) for the change to take effect.
„
Max Burst Length – Enables you to set the iSCSI maximum burst length.
To change this setting, select the desired value (ranging from 512 to
262144 bytes) from the drop-down menu.
„
Max First Burst Length – Enables you to set the iSCSI maximum first burst
length. To change this setting, select the desired value (ranging from 512 to
262144 bytes) from the drop-down menu.
„
Security Settings
„
Enable Header Digest – Enables or disables support for iSCSI header
digest. Header digest is an ISCSI feature that adds a validity check
field to iSCSI PDU headers to verify that no corruption has occurred
during the transmission of the PDU header. The SANbox 6142 router
supports digest in its hardware to maximize performance. When you
change this setting, you must click Save (at the bottom of the page) for
the change to take effect.
„
Enable Data Digest – Enables or disables support for iSCSI data
digest. Data digest is an ISCSI feature that adds a validity check to
iSCSI data to verify that no corruption has occurred during the
transmission of the data. The SANbox 6142 router supports data
digest in its hardware to maximize performance. When you change this
setting, you must click Save (at the bottom of the page) for the change
to take effect.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
FI0054601-00 C
CHAP Settings
„
Enable CHAP – Enables or disables CHAP (Challenge Handshake
Authentication Protocol) support. Select the check box to enable this
option; clear the check box to disable it. When you change this setting,
you must click Save (at the bottom of the page) for the change to take
effect.
„
CHAP Secret – Lets you define the CHAP secret used for
authenticating an iSCSI client. The field is available only when the
Enable CHAP check box is checked. When you change the CHAP
Secret setting, you must click Save (at the bottom of the page) for the
change to take effect.
7-29
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
Statistics Tab
The Statistics tabbed page consists of a scrollable table of parameters and values.
The table is divided into two sections: the first section contains statistics that are
port specific, and the second section contains shared statistics (common to both
iSCSI ports).
You can refresh the statistics are by clicking Refresh at the top of the scrollable
window. You can clear the statistics (set all values to zero) by clicking Clear.
Figure 7-25 iSCSI Statistics Tabbed Page
7-30
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Discovered iSCSI Initiators
Selecting the Discovered iSCSI Initiators branch on the system tree does not
provide any information in the right window. Select a discovered iSCSI initiator in
the system tree to display the Information and LUN List tabbed pages to the right
of the system tree, which are shown in Figure 7-26 and described in the following
sections.
Figure 7-26 Discovered iSCSI Initiator Tabbed Pages
Information Tab
The Information tabbed page consists of two sections: Initiator Information and
CHAP Settings. The following paragraphs describe the information displayed in
these sections.
The Initiator Information section provides the following parameters:
„
iSCSI IP Address – Displays the IP address of the discovered iSCSI
initiator.
„
iSCSI Alias – Displays the iSCSI initiators alias, which the initiator provides
when it logs into the iSR-6142 router.
„
Status – Displays the activity status for the selected initiator.
FI0054601-00 C
7-31
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
The CHAP Settings section provides the following parameters:
„
Enable CHAP – Enables or disables CHAP (Challenge Handshake
Authentication Protocol) support. Select the check box to enable this option;
clear the check box to disable it.
„
CHAP Secret – Lets you define the CHAP secret used for authenticating an
iSCSI client. The field is available only when the CHAP check box is
checked.
NOTE:
To apply any changes, click the Save button, located at the bottom of
window.
Local Presented Target Tab
The Local Presented Target tabbed page consists of a scrollable list of logical unit
numbers (LUNs) mapped to the iSCSI initiator, as shown in Figure 7-27 and
described in the following paragraphs.
Figure 7-27 Local Presented Target Tabbed Page
7-32
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
Port – Displays information provided by the target LUN as a result of issuing
a SCSI Inquiry command.
„
Protocol – Identifies the target name. For FC targets, the name is the
WWPN.
„
WWPN/IQN – Specifies the world wide unique LUN name (WWULN), also
provided on page 83 of a SCSI Inquiry command.
„
WWNN – Shows the logical unit number.
Remote Presented Target Tab
The Remote Presented Target tabbed page consists of a scrollable list of LUNs
mapped to the iSCSI initiator, as shown in Figure 7-28 and described in the
following paragraphs.
Figure 7-28 Remote Presented Target Tabbed Page
„
Remote Port – Displays information provided by the target LUN in response
to the router issuing a SCSI Inquiry command.
„
Protocol – Displays information provided by the target LUN in response to
the router issuing a SCSI Inquiry command.
„
Type – Displays information provided by the target LUN in response to the
router issuing a SCSI Inquiry command.
FI0054601-00 C
7-33
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
„
Status – Displays information provided by the target LUN in response to the
router issuing a SCSI Inquiry command.
„
WWPN – Displays information provided by the target LUN in response to the
router issuing a SCSI Inquiry command.
„
Remote IQN – Displays information provided by the target LUN in response
to the router issuing a SCSI Inquiry command.
FC Discovered Targets
Selecting an FC discovered target in the system tree does not provide any
information in the right window. Select a discovered FC target to display the
Information and Remote Presented Devices tabbed pages to the right of the
system tree (see Figure 7-29).
Figure 7-29 FC Discovered Targets Tabbed Pages
7-34
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Information Tab
The Information tabbed page provides the following information about the
selected FC target:
„
Product Vendor – Displays the product vendor as reported by the SCSI
Inquiry command.
„
Product ID – Displays the product ID as reported by the SCSI Inquiry
command.
„
Product Revision – Displays the product revision as reported by the SCSI
Inquiry command.
„
Node Name – Displays the world-wide node name of the target device.
„
Port Name – Displays the world-wide port name of the target device.
„
Port ID – Displays the target device’s port ID.
Remote Presented Devices Tab
The Remote Presented Devices tabbed page provides detailed target information
and a scrollable list of LUNs, as shown in Figure 7-30 and described in the
following paragraphs.
Figure 7-30 Remote Presented Devices Tab
„
FI0054601-00 C
General Information
„
Product Vendor – Displays the vendor name of the target device as
reported by the SCSI Inquiry command.
„
Product ID – Displays the product ID of the target device as reported
by the SCSI Inquiry command.
„
Product Revision – Displays the product revision of the target device
as reported by the SCSI Inquiry command.
„
Node Name – Displays the world-wide node name of the target
device.
7-35
S
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
„
Port Name – Displays the world-wide port name of the target device.
„
Port ID – Displays the target device’s port ID.
„
Target Type – Displays the FC port where the target device was
discovered.
„
Target Path – Displays the logical unit number.
„
Target Mode – Displays the vendor name of the LUN as reported by
the SCSI Inquiry command.
Presented On – Displays the product ID of the LUN as reported by the SCSI
Inquiry command.
„
Presented Port – Displays the product revision of the LUN as reported
by the SCSI Inquiry command.
„
Protocol – Displays the protocol in use, either iSCSI or FC.
„
WWNN/IQN – Displays the WWULN of the LUN as reported on page
83 of the SCSI Inquiry command.
„
WWPN – Displays the capacity (in megabytes) of the LUN as reported
by the SCSI Capacity command.
iSCSI Presented Target List Tabbed Page
The iSCSI Presented Target List tabbed page provides detailed FC target
information and a scrollable list of the iSCSI presentations of the target, as shown
in Figure 7-31 and described in the following paragraphs.
7-36
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
Figure 7-31 iSCSI Presented Target List Tabbed Page
„
Device Product Vendor – Displays the vendor name of the target device as
reported by the SCSI Inquiry command.
„
Device Product ID – Displays the product ID name of the target device as
reported by the SCSI Inquiry command.
„
Device Product Rev – Displays the product revision of the target device as
reported by the SCSI Inquiry command.
„
Device Node Name – Displays the world-wide node name of the target
device.
„
Device Port Name – Displays the world-wide port name of the target
device.
„
Device Port ID – Displays the target device’s port ID.
„
Presented Port – Displays the iSCSI port number where the target is
presented (1 or 2).
„
IP Address – Displays the IP address on which the target is presented.
„
Alias – Displays the iSCSI alias of the presented target.
„
iSCSI Name – Displays the presented target’s iSCSI name.
„
Size – Displays the capacity (in megabytes) of the LUN as reported by the
SCSI Capacity.
FI0054601-00 C
7-37
S
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
iSCSI Discovered Targets
The iSCSI Discovered Targets branch on the system tree does not provide any
information in the right window. Select a discovered target to display the
Information tabbed page to the right of the system tree (see Figure 7-32).
Figure 7-32 iSCSI Discovered Targets Tabbed Pages
Information Tabbed Page
The Information tabbed page consists of two sections: General Information and
CHAP Settings, which are described in the following paragraphs.
„
7-38
General Information
„
Product Vendor – Displays the product vendor as reported by the
SCSI Inquiry command.
„
Product ID – Displays the product ID as reported by the SCSI Inquiry
command.
„
Product Revision – Displays the product revision as reported by the
SCSI Inquiry command.
„
IP Address – Displays the IP address of the presented iSCSI target.
„
iSCSI Name – Displays the presented iSCSI target’s name.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
„
Target Path – Displays the router’s iSCSI port where the target was
discovered.
CHAP Settings – Provides an option you can use to set the challenge
handshake authentication protocol (CHAP) option as follows:
„
Enable CHAP – Select this check box to enable CHAP when
connecting to this target.
„
CHAP Secret – When the Enable CHAP option is enabled, you can
enter the string used for the CHAP secret when connecting to this
target.
NOTE:
If you change the CHAP Settings, you must click Save for the change
to take effect.
FCIP Routes
Selecting the FCIP Routes branch on the system tree does not provide any
information in the right window. Select an FCIP Route Info # in the system tree to
display the branch to display the FCIP Route Information and Statistics tabbed
pages to the right of the system tree.
Figure 7-33 FCIP Route Tabbed Pages
FI0054601-00 C
7-39
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
FCIP Route Information Tabbed Page
The FCIP Route Information tabbed page contains the information that defines the
selected FCIP route, as described in the following paragraphs.
7-40
„
FCIP Interface Status – Provides a drop-down box you can use to enable
or disable the FCIP route. Disabling the route places the FC and GE ports in
a down state, but still retains all route configuration parameters.
„
FC Port – Identifies the FC port assigned to the FCIP route when it was
created.
„
FC Link Status – Shows the state of the FC port used in this FCIP route.
„
GigE Port – Identifies the gigabit Ethernet (GigE) port assigned to the FCIP
route when it was created.
„
GigE Link Status – Shows the state of the GigE port used in this FCIP
route.
„
Local IP Address – Fields you can use to define the IP address to be used
by the GigE port. An uninitialized port has an IP address of all zeros.
„
Remote IP Address – Fields you can use to define the IP address of the
GigE port on the remote router.
„
Subnet Mask – Fields you can use to define the subnet mask used by the
GigE port.
„
Gateway IP Address – Fields you can use to define the gateway IP address
used by the GigE port.
„
Jumbo Frames – Provides a drop-down box you can use to enable or
disable Jumbo IP frames. When disabled, the MTU is 1500 bytes; when
enabled, the maximum MTU is 9000 bytes.
„
TCP Window Size – Provides a drop-down box you can use to choose one
of three options for TCP window size: 8192, 16384, or 32768 bytes. The
default is 32768.
„
Window Scaling – Provides a drop-down box you can use to enable or
disable TCP window scaling. The default is disabled.
„
Window Scaling Factor – When Window Scaling is enabled, use this
drop-down box to choose one of six options for TCP window scaling: 0–5.
„
TCP Port Number – Field you can use to define the TCP port number.
„
GigE Link Rate – Provides a drop-down box from which you can choose the
link rate of the GigE port from one of four options: Auto, 10 Mbps, 100 Mbps,
or 1000 Mbps.
„
Link Rate Mode – When the GigE Link Rate is set to something other than
auto, use this drop-down box to choose one of three options for the link rate
mode: auto, half duplex, or full duplex.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
„
GigE Port Flow Control – When the GigE Link Rate is set to something
other than auto, use this drop-down box to enable or disable GigE port flow
control. The default is enabled.
„
VLAN Enabled – Provides a drop-down box you can use to enable or
disable VLAN support. The default is disabled.
„
VLAN ID – When VLAN is enabled, use this field to define the VLAN ID. The
VLAN ID must be the same on both routers participating in the FCIP route
(local and remote routers must be using same VLAN ID) and the Ethernet
switches.
„
VLAN Priority – When VLAN is enabled, use this drop-down box to set the
VLAN priority to one of eight options: 0 through 7.
„
Error Detect Timeout – Provides a drop-down box you can use to set the
error detect timeout value by selecting one of five options: 1 to 5 seconds.
The default is one second.
„
Resource Allocate Timeout – Provides a drop-down box you can use to
set the resource allocate timeout value to one of five options: 1 to 5 seconds.
The default is one second.
„
FCIP Timestamp – Provides a drop-down box you can use to enable or
disable FCIP timestamps. The default is enabled.
„
FCIP SW Compression – Provides a drop-down box you can use to enable
or disable FCIP compression. The default is disabled.
„
Bandwidth (Mbit/sec) – Use this field to define the maximum bandwidth (in
megabits per second) the GigE port will use during transmits. The range of
values supported is 1 to 1000 megabits per second. Use this setting to limit
the bandwidth used by the FCIP route so it doesn't consume all the available
link bandwidth. For example, if the slowest link in the WAN being used is a
DS-3 link, then the maximum available bandwidth is 45 megabits per
second. To limit the FCIP route to 33% of the overall link bandwidth, set the
bandwidth to 15 megabits per second.
NOTE:
To apply any changes made to this screen, click the Save button, located at
the bottom of window.
FI0054601-00 C
7-41
7 – SANsurfer iSCSI/FC Router Manager
System Tree Window
S
FCIP Route Statistics Tabbed Page
The Statistics tabbed page consists of a scrollable table of parameters and values.
Figure 7-34 FCIP Route Statistics Page
You can refresh the statistics are by clicking Refresh at the top of the scrollable
window. You can clear the statistics (set all values to zero) by clicking Clear.
7-42
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Wizards
The SANsurfer iSCSI/FC Router Manager provides easy-to-use wizards that walk
you through various router configuration procedures. You can launch an available
wizard using any of the following methods:
„
Select an option from the Wizards menu, located on the Router Manager’s
menu bar (see page 7-5.)
„
Right-click anywhere within the router’s node in tree window and select one
of the wizards available from the action menu (see page 7-8.)
„
If the router manager identifies unconfigured ports when you first connect to
a router, it automatically launches the configuration wizard.
The following topics describe how to use the available wizards:
„
Configuration Wizard (see page 7-44)
„
Add Initiator Wizard (see page 7-49)
„
FW Update Wizard (see page 7-51)
„
Map Local Initiator/Target Wizard (see page 7-55)
„
Unmap Local Initiator/Target Wizard (see page 7-63)
„
Add Remote Router Wizard (see page 7-68)
„
Remove Remote Router Wizard (see page 7-72)
„
Map Remote Initiator/Target Wizard (see page 7-75)
„
Remote Mapped Device (see page 7-81)
„
Discover iSCSI Target Wizard (see page 7-84)
„
FCIP Route Add Wizard (see page 7-86)
„
FCIP Route Remove Wizard (see page 7-92)
FI0054601-00 C
7-43
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
Configuration Wizard
The Configuration Wizard provides a set of dialog boxes that walk you through the
steps required for configuring the iSCSI ports. This wizard starts automatically
when your system connects to a system with any un-configured iSCSI ports.
You can also start this wizard at any time by selecting Configuration Wizard from
the Wizards menu or from the Action Menu.
After launching the Configuration Wizard, it displays the iSCSI Port Selection
dialog box (see Figure 7-35).
Figure 7-35 iSCSI Port Selection Dialog Box
To use the Configuration Wizard, follow these steps:
1.
On the iSCSI Port Selection dialog box, select an unconfigured iSCSI port,
enter the symbolic name for the router (if desired), then click Next.
The iSCSI Port Connection Settings Panel dialog box displays (see
Figure 7-36).
7-44
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Figure 7-36 iSCSI Port Connection Settings Panel Dialog Box
2.
To configure the iSCSI Port IPV4 settings:
a.
b.
3.
FI0054601-00 C
Type the information in the following fields.
„
IP Address
„
Subnet Mask
„
Gateway
If desired, configure the IP address of the iSNS server with which the
router registers the selected iSCSI port:
„
Select the Enable iSNS check box to make the Server IP
address field editable.
„
Enter the IP address of the iSNS server in the Server IP address
field.
Click Next. The iSCSI Port IPv6 Settings Panel appears, as shown in
Figure 7-37.
7-45
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Figure 7-37 iSCSI Port IPv6 Settings Panel
4.
To configure the iSCSI port IPv6 connection using this dialog box, follow
these steps:
a.
Select Enable IPv6 Address to make the fields editable.
b.
Specify the iSCSI port IPv6 network settings:
c.
5.
7-46
„
Enter the IPv6 Address 0.
„
Enter the IPv6 Address 1.
„
Enter the IPv6 Default Router.
„
Enter the IPv6 Link Local.
If desired, configure the IP address of the iSNS server with which the
router registers the selected iSCSI port:
„
Select the Enable iSNS check box to make the Server IP
address field editable.
„
Enter the IP address of the iSNS server in the Server IP address
field.
Click Next. The Confirm Changes dialog box displays, as shown in
Figure 7-38.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Figure 7-38 Confirm Changes Dialog Box
6.
FI0054601-00 C
Review the configuration changes displayed on the screen, then click Next
to confirm your changes.
7-47
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The system displays the iSCSI Port Configuration Status dialog box, as
shown in Figure 7-39.
Figure 7-39 iSCSI Port Configuration Status
7.
Read the information about the status changes, then click Next.
The system displays the Refresh dialog box.
8.
Read the information. If you would like to see the new configuration, click
Yes; otherwise, click No.
The system displays the Finish dialog box, as shown in Figure 7-40.
7-48
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Figure 7-40 Configuration Wizard Finish Dialog Box
9.
Read the information, then click Finish.
Add Initiator Wizard
The Add Initiator Wizard provides a dialog box used to enter an iSCSI initiator into
the system database. iSCSI initiators are normally discovered (their name and
address are captured) the first time they log in to the SANbox 6142 router.
This wizard allows you to enter the initiator information before the log in, thus
allowing you to map LUNs to the initiator before logging into the SANbox 6142.
You can also start this wizard at any time by selecting Add Initiator Wizard from
the Wizards Menu or from the Action Menu.
After launching the Configuration Wizard, the system displays the iSCSI Port
Selection dialog box, as shown in Figure 7-41.
FI0054601-00 C
7-49
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
Figure 7-41 Create an Initiator Dialog Box
To create an initiator:
1.
Type a name in the Initiator name box.
2.
Type an alias in the Initiator alias (iSCSI) box.
3.
If you want to enable CHAP for this initiator, select the CHAP Enabled
check box. If you want a CHAP secret, type the name in the Initiator’s CHAP
Secret box.
4.
Click Finish. The Security Check dialog box displays, as shown in
Figure 7-42.
Figure 7-42 Security Check Dialog Box
5.
7-50
Type the appropriate password, then click OK.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The new iSCSI initiator is displayed in the discovered iSCSI initiator’s
section of the system tree, as shown in Figure 7-43.
Figure 7-43 System Tree with New iSCSI Initiator
FW Update Wizard
The FW Update Wizard provides a set of dialog boxes that walk you through the
steps required for updating the SANbox 6142 firmware. This wizard helps you
update the firmware on selected router. When you first launch this wizard, the
Router Selection dialog box displays all detected routers, as shown in
Figure 7-44.
You can start this wizard at any time by selecting FW Update Wizard from the
Wizards Menu or from the Action Menu.
Figure 7-44 Router Selection Dialog Box
FI0054601-00 C
7-51
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
To update the firmware, follow these steps:
1.
Select the check box next to the routers whose firmware you want to update,
then click Next. The Open dialog box displays.
Figure 7-45 Firmware File Selection Dialog Box
7-52
2.
Enter in the path to the firmware file, or click Browse to locate the firmware
file.
3.
When the firmware file is displayed in the Firmware Image File field, click
Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Confirm Changes dialog box displays, as shown in Figure 7-46.
Figure 7-46 Confirm Changes Dialog Box
4.
Read the information, then do the following:
a.
If you want to save a copy of this firmware configuration, click Save
Configuration to File. Browse to the desired directory, type a file
name, then click Save.
b.
Click Next. The Security Check dialog box requests the Admin
password, as shown in Figure 7-47.
Figure 7-47 Security Check Dialog Box
c.
5.
FI0054601-00 C
Type the appropriate password, then click OK to start the firmware
update.
The Firmware Update Status dialog box shows the progress of the update
in the message section, as shown in Figure 7-48.
7-53
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Figure 7-48 Firmware Update Status Dialog Box—Progress
When the firmware has loaded successfully, the system displays the Finish dialog
box, along with the Update success dialog box, as shown in Figure 7-49.
Figure 7-49 Finish Dialog Box (Successful Firmware Update)
7-54
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
NOTE:
The new firmware will not take effect until the system is rebooted.
6.
Complete the wizard:
a.
If you want to reboot the system now, click Yes. Otherwise, click No.
b.
Click Finish.
Map Local Initiator/Target Wizard
The Map Local Initiator/Target Wizard provides a set of dialog boxes that walk you
through the steps required for mapping a local initiator to a local target.
You can start this wizard at any time by selecting Map Local Initiator/Target
Wizard from the Wizards Menu or from the Action Menu.
When the Map Local Initiator/Target wizard launches, the Select an Initiator
dialog box displays a list of locally connected initiators (FC or iSCSI), as shown in
Figure 7-50.
Figure 7-50 Initiator Selection Dialog Box
To map a local target to a local initiator:
1.
FI0054601-00 C
Select the check box next to the initiator you want to map, then click Next.
7-55
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Select a Target dialog box opens, as shown in Figure 7-51.
Figure 7-51 Select a Target Dialog Box
2.
7-56
Select a target you want mapped to the previously selected initiator, then
click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The wizard screen prompts you to select a port on which the initiator will be
presented, as shown in Figure 7-52.
Figure 7-52 Select Initiator Port Dialog Box
3.
FI0054601-00 C
Select the port (FC Port 1 or FC Port 2), then click Next.
7-57
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The wizard screen prompts you to select a port on which the target will be
presents (iSCSI Port 1 and iSCSI Port 2), as shown in Figure 7-53.
Figure 7-53 Select Target Presentation Port Dialog Box
7-58
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Confirm Changes dialog box displays the local mapping done in the
previous steps, as shown in Figure 7-54.
Figure 7-54 Confirm Changes Dialog Box
4.
FI0054601-00 C
Review the information, then click Next.
7-59
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The Security Check dialog box requests the Admin password, as shown in
Figure 7-55.
Figure 7-55 Security Check Dialog Box
5.
7-60
Type the appropriate password, then click OK to confirm the local mapping.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Initiator/Target Mapping Configuration Status dialog box displays
local mapping completion status, as shown in Figure 7-56.
Figure 7-56 Initiator/Target Mapping Configuration Status Dialog Box
6.
FI0054601-00 C
After reviewing the initiator to target mapping configuration status, click
Next.
7-61
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
After completing the Map Local Initiator/Target wizard, you can see the mapping
by selecting the mapped Initiator in the system tree under Discovered iSCSI
Initiators. Click the Local Presented Devices tab, as shown in Figure 7-57. In
this example an iSCSI initiator is mapped to an FC target, other mappings are
supported such as FC to FC, FC to iSCSI and iSCSI to iSCSI.
Figure 7-57 Discovered iSCSI Initiators - Local Presented Targets
7-62
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Unmap Local Initiator/Target Wizard
The Unmap Local Initiator/Target Wizard provides a set of dialog boxes that walk
you through the steps required for removing a local initiator from a local target
mapping.
You can start this wizard at any time by selecting Unmap Local Initiator/Target
Wizard from the Wizards Menu or from the Action Menu.
When the UnMap Local Initiator/Target wizard launches, the Select an Initiator
dialog box displays a list of locally connected initiators (FC or iSCSI), as shown in
Figure 7-58.
Figure 7-58 Initiator Selection Dialog Box
To unmap a local target from a local initiator:
1.
FI0054601-00 C
Select the check box next to the initiator you want to unmap, then click Next.
7-63
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The Presented Target Selection dialog box displays a list of targets
mapped to the initiator selected in the previous step, as shown in
Figure 7-59.
Figure 7-59 Presented Target Selection Dialog Box
2.
7-64
Select the check box next to the target to unmap, then click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Security Check dialog box requests the Admin password, as shown in
Figure 7-60.
Figure 7-60 Security Check Dialog Box
3.
FI0054601-00 C
Type the appropriate password, then click OK to confirm the target is
unmapped.
7-65
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Unpresent Initiator/Target Status dialog box displays the results of the
unmap operation, as shown in Figure 7-61.
Figure 7-61 Unpresent Initiator/Target Status Dialog Box
4.
7-66
Review the status, then click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
After completing the UnMap Local Initiator/Target wizard you can verify the
unmapping by selecting the Initiator in the system tree under Discovered iSCSI
Initiators. Then select Local Presented Devices.
For the example shown in Figure 7-62, an iSCSI initiator was unmapped from an
FC target.
Figure 7-62 Discovered iSCSI Initiators - Local Presented Targets
FI0054601-00 C
7-67
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
Add Remote Router Wizard
The Add Remote Router Wizard provides a set of dialog boxes that walk you
through the steps required for assigning a remote router to your local router as a
peer.
You can start this wizard at any time by selecting Add Remote Router Wizard
from the Wizards Menu or from the Action Menu.
When the Add Remote Router wizard launches, the Remote Router’s IP
Address dialog box requests the remote router’s IP address, as shown in
Figure 7-63.
Figure 7-63 Remote Router’s IP Address Dialog Box
To add a remoter router to a local router:
1.
7-68
Type the IP Address of the remote router, then click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Status dialog box displays the remote router information along with the
Local Router Admin Password dialog box, as shown in Figure 7-64.
Figure 7-64 Local Router Admin Password Dialog Box
2.
Type the local router admin password (default=config), then click OK.
The Status dialog box displays the remote router information, as shown in
Figure 7-65.
Figure 7-65 Add Remote Router Status Dialog Box
FI0054601-00 C
7-69
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
3.
Review the status, then click Finish.
4.
Click the Refresh icon to refresh the display.
5.
Select the router node, then select the Assigned Remote Router:1 tab to
display the remote router’s information, as shown in Figure 7-66.
Figure 7-66 Assigned Remote Router Display
7-70
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
6.
Click the Topology tab to display the local and remote router topology
including devices attached to both routers, as shown in Figure 7-67.
Figure 7-67 Topology Display
FI0054601-00 C
7-71
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
Remove Remote Router Wizard
The Remove Remote Router Wizard provides a set of dialog boxes that walk you
through the steps required for removing a remote router from the local router.
You can start this wizard at any time by selecting Remove Remote Router
Wizard from the Wizards Menu or from the Action Menu.
When the Remove Remote Router wizard launches, the Select a Remote Router
to unmap dialog box displays a list of mapped routers, as shown in Figure 7-68.
Figure 7-68 Select Remote Router Dialog Box
To remove a remoter router from a local router:
1.
7-72
Select the remote router to be removed, then click OK.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Local Router Admin Password dialog box requests the local router’s
admin password to complete the unmap, as shown in Figure 7-69.
Figure 7-69 Local Router Admin Password Dialog Box
2.
Type the local router’s admin password (default=config), then click OK.
The system prompts you to refresh the display, as shown in Figure 7-70.
Figure 7-70 Refresh Screen
3.
FI0054601-00 C
Click Yes to refresh the display.
7-73
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Remove Remote Router Completion dialog box displays the
completion status, as shown in Figure 7-71.
Figure 7-71 Remove Remote Router Completion Dialog Box
4.
7-74
Click OK to close the message box.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
Map Remote Initiator/Target Wizard
The Map Remote Initiator/Target Wizard provides a set of dialog boxes that walk
you through the steps required for mapping an initiator to a target one of which is
remote and the other local.
You can start this wizard at any time by selecting Map Remote Initiator/Target
Wizard from the Wizards Menu or from the Action Menu.
When the Map Remote Initiator/Target wizard launches, the Device Selection
dialog box displays a list of devices, as shown in Figure 7-72. If necessary,
expand the router tree to see the attached devices.
Figure 7-72 Device Selection Dialog Box
To create a remote-to-local mapping between an initiator to a target:
1.
Select the device to be mapped. The device may be a target or an initiator
and may be either on the remote router or on the local router.
2.
Click Next.
FI0054601-00 C
7-75
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The Device Selection dialog box displays list of devices, as shown in
Figure 7-73.
Figure 7-73 Device Selection Dialog Box
3.
7-76
If necessary, expand the router tree to see the attached devices. Select the
device to be mapped. The device may be a target or an initiator and may be
on either the remote router or on the local router. Click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The port selection dialog box prompts you to select a port the system will
use to connect to the device, as shown in Figure 7-74.
Figure 7-74 Port Selection Dialog Box
4.
FI0054601-00 C
Select the port the system will use to connect to the device, then click Next.
7-77
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The Device Mapping Option dialog box displays SmartWrite mapping
options, as shown in Figure 7-75.
Figure 7-75 Device Mapping Option Dialog Box
7-78
5.
If your router includes the SmartWrite feature, Enable or Disable the
options as you want.
6.
Click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Confirm Mapping dialog box displays the mapping and option
selections, as shown in Figure 7-76.
Figure 7-76 Confirm Mapping Dialog Box
7.
Review the information and, if correct, click Next.
The Local Router Admin Password dialog box displays, as shown in
Figure 7-77.
Figure 7-77 Local Password Dialog Box
8.
FI0054601-00 C
Type the local router admin password (default=config), then click OK.
7-79
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The Remote Mapping Status screen displays a list of newly mapped
devices, as shown in Figure 7-78.
Figure 7-78 Local Router Admin Password Dialog Box
9.
Review the status information, then click Finish.
The system prompts you to refresh the display, as shown in Figure 7-79.
Figure 7-79 Refresh Screen
10.
7-80
Click Yes to refresh the display.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
11.
View the mapped devices in the router’s tree window. Figure 7-80 shows the
mapping created in the sample procedures.
Figure 7-80 Remote Mapped Device
Unmap Remote Initiator/Target Wizard
The Unmap Remote Initiator/Target Wizard provides a set of dialog boxes that
walk you through the steps required for removing an initiator-to-target mapping.
You can start this wizard at any time by selecting Unmap Remote Initiator/Target
Wizard from the Wizards Menu or from the Action Menu.
When the Unmap Remote Initiator/Target wizard launches, the Device Selection
dialog box displays a list of remote mapped devices, as shown in Figure 7-81.
FI0054601-00 C
7-81
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
Figure 7-81 Device Selection Dialog Box
To unmap an initiator and target:
1.
7-82
Select the device to be unmapped, then click Next.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Local Router’s Admin Password dialog box requests the local
router’s admin password to continue with the unmap, as shown in
Figure 7-82.
Figure 7-82 Local Router Admin Password Dialog Box
2.
Type the local router’s admin password (default=config), then click OK.
The Remote Unmap Initiator-Target Status dialog box displays the status
of the unmap operation, as shown in Figure 7-83.
Figure 7-83 Remote Unmap Initiator-Target Status Dialog Box
3.
FI0054601-00 C
Review the status, then click Finish.
7-83
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
Discover iSCSI Target Wizard
The Discover iSCSI Target Wizard provides a set of dialog boxes that walk you
through the steps required for discovering an iSCSI target.
You can start this wizard at any time by selecting Discover iSCSI Target from the
Wizards Menu or from the Action Menu.
When the Discover iSCSI Target wizard launches, the first window requests you to
enter data: an IP address for the iSCSI target, the target’s TCP port number
(default is 3260) and the router’s GE port to be used for the discovery, as shown in
Figure 7-84.
Figure 7-84 Discover iSCSI Target Wizard—IP Address Dialog Box
To discover an iSCSI target:
1.
Enter the IP address.
2.
Select the GE port from the Outbound Port drop-down list.
3.
Click Finish to initiate the discovery operation.
The Security Check dialog box requests the administrator password, as
shown in Figure 7-85.
Figure 7-85 Discover iSCSI Target Wizard—Security Check Dialog Box
7-84
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
4.
Type the appropriate password, then click OK to confirm the discovery of the
iSCSI target.
If the wizard detected iSCSI targets, the Refresh dialog box signifies the
discovery of the iSCSI target, as shown in Figure 7-86. This dialog box may
take a few seconds before appearing.
Figure 7-86 Discover iSCSI Target Wizard—Refresh Dialog Box
5.
Click Yes to refresh system tree with the discovered iSCSI target, or click No
to skip the refresh.
After the refresh is complete, you can see the Discovered iSCSI Target in
the system tree, as shown in Figure 7-87.
Figure 7-87 iSCSI Discovered Targets
FI0054601-00 C
7-85
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
FCIP Route Add Wizard
The FCIP Route Add Wizard provides a set of dialog boxes that walk you through
the steps required for adding an FCIP route.
You can start this wizard at any time by selecting FCIP Route Add from the
Wizards Menu or from the Action Menu.
When the FCIP Route Add Wizard launches, it displays a warning message,
letting you know the operation may drop the connection to the selected GE and
FC ports. If the router uses the selected ports in FC or iSCSI mappings, it will lose
connectivity to them. Using this wizard will also momentarily disrupt connectivity
on the GE port not selected for the FCIP route.
Figure 7-88 FCIP Route Add Wizard—Warning Dialog Box
To add an FCIP route:
1.
7-86
Read the warning. If you want to proceed, click Yes and continue with
step 2. Otherwise, click No to cancel the wizard.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The FC and GigE Port Selection dialog box prompts you to select an
FC-GigE port pair, as shown in Figure 7-89.
Figure 7-89 FCIP Route Add Wizard—Port Selection Dialog Box
2.
Select the FC-GigE Port pair. The corresponding parameter options become
available.
3.
If desired, configure the following port route/parameters:
4.
FI0054601-00 C
„
FCIP Interfaces FC & GE – Provides a drop-down box you can use to
enable or disable the FCIP route. Disabling the route places the FC
and GE ports in a down state. It still retains all route configuration
parameters.
„
GigE Port Programmed Link Rate – Provides a drop-down box you
can use select one of four options for the GigE link rate: auto, 10, 100,
or 1000. The default link rate is auto.
„
Link Rate Mode – Provides a drop-down box you can use select one
of three options for the link rate mode: auto, half duplex, or full duplex.
This dialog box is available only when the GigE link rate is set to
something other than auto.
„
GigE Port Flow Control – Provides a drop-down box you can use to
enable or disable GigE port flow control. The default is enabled. This
dialog box is available only when the GigE link rate is set to something
other than auto.
After selecting a port pair and setting GE port parameters, click Next to
continue or click Cancel to quit the wizard.
7-87
7 – SANsurfer iSCSI/FC Router Manager
Wizards
S
The Local and Remote IP Address dialog box requests entry of IP
addresses (see Figure 7-90).
Figure 7-90 FCIP Route Add Wizard—Local and Remote IP Address Dialog Box
5.
6.
7-88
Configure any of the following parameters:
„
Local IP Address – Enter the IP address the GigE port will use. An
uninitialized port has an IP address of all zeros.
„
Subnet Mask – Enter the subnet mask the GigE port will use.
„
Gateway IP Address – Enter the gateway IP address the GigE port
will use.
„
Remote IP Address – Enter the IP address of the GigE port the GigE
port will use on the remote router.
After setting the IP address parameters, click Next to continue or click
Cancel to quit the wizard.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The TCP/IP Options dialog box requests entry of TCP/IP parameters, as
shown in Figure 7-91.
Figure 7-91 FCIP Route Add Wizard—TCP/IP Options Dialog Box
7.
FI0054601-00 C
Configure any of the following parameters:
„
Jumbo Frames – Provides a drop-down box you can use to enable or
disable Jumbo IP frames. When disabled the MTU is 1500 bytes.
When enabled the MTU is 9000 bytes.
„
TCP Window Size – Provides a drop-down box you can use select
one of three options for TCP window size: 8192, 16384, or 32768
bytes. The default is 32768.
„
Window Scaling – Provides a drop-down box you can use to enable
or disable window scaling. The default is disabled.
„
Window Scaling Factor – Provides a drop-down box you can use
select one of six options for TCP window scaling, any number between
0–5.
„
VLAN Enabled – Provides a drop-down box you can use to enable or
disable VLAN support. The default is disabled.
„
VLAN ID – Provides a text field you can use to enter the VLAN ID. This
option is available only when VLAN is enabled. The VLAN ID must be
the same on both routers participating in the FCIP route (that is, local
and remote routers must be using same VLAN ID) and the Ethernet
switches.
7-89
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
„
8.
VLAN Priority – Provides a drop-down box that contains eight options
for the VLAN priority: any number between 0–7. This dialog box is
available only when VLAN is enabled.
After setting the TCP/IP parameters, click Next to continue or click Cancel
to quit the wizard.
The FCIP Options dialog box requests entry of FCIP parameters, as shown
in Figure 7-92.
Figure 7-92 FCIP Route Add Wizard—FCIP Options Dialog Box
9.
7-90
Configure any of the following parameters:
„
FCIP Timestamp – Provides a drop-down box you can use to enable
or disable FCIP timestamps. The default is enabled.
„
Error Detect Timeout – Provides a drop-down box you can use to
select one of five options for the error detect timeout: any number
between 1 to 5 seconds. The default is one second.
„
Resource Allocate Timeout – Provides a drop-down box you can use
to select one of five options for the resource allocate timeout: any
number between 1 to 5 seconds. The default is one second.
„
FCIP SW Compression – Provides a drop-down box you can use to
enable or disable FCIP compression. The default is disabled.
„
Bandwidth (Mbit/sec) – Provides a text field in which you can enter
the maximum bandwidth (in megabits per second) used by the GigE
port during transmits. The range of values supported is 1 to 1000
megabits per second. This setting allows you to limit the bandwidth
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
used by the FCIP route so as to not consume all the available link
bandwidth. For example, if the slowest link in the WAN being used is a
DS-3 link, the maximum available bandwidth is 45 megabits per
second. To limit the FCIP route to 33% of the overall link bandwidth set
the bandwidth to 15 megabits per second.
10.
After setting the FCIP parameters, click Next to continue or click Cancel to
quit the wizard.
The Security Check dialog box requests the administrator password, as
shown in Figure 7-93.
Figure 7-93 FCIP Route Add Wizard—Security Check Dialog Box
11.
Type the appropriate password, then click OK to confirm adding the FCIP
route.
The Add FCIP Route Complete dialog box lets you know when the
configuration is complete, as shown in Figure 7-94.
Figure 7-94 FCIP Route Add Wizard—Completed Dialog Box
NOTE:
This dialog box may take a few seconds before appearing.
12.
FI0054601-00 C
Click OK to exit the dialog box.
7-91
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
FCIP Route Remove Wizard
The FCIP Route Remove Wizard provides a set of dialog boxes that walk you
through the steps required for removing an FCIP route.
You can start this wizard at any time by selecting FCIP Route Remove from the
Wizards Menu or from the Action Menu.
When the FCIP Route Remove wizard launches, it displays a warning message,
letting you know the operation may drop the connection to the selected GE and
FC ports. If the router uses the selected ports in FC or iSCSI mappings, it will lose
connectivity to them. Using this wizard will also momentarily disrupt connectivity
on the GE port not selected for the FCIP route.
Figure 7-95 FCIP Route Remove Wizard—Warning Dialog Box
To remove an FCIP route:
1.
7-92
Read the warning. If you want to proceed, click Yes and continue with
step 2. Otherwise, click No to cancel the wizard.
FI0054601-00 C
A
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The FCIP Remove dialog box displays a list of existing FCIP routes, as
shown in Figure 7-96.
Figure 7-96 FCIP Route Remove Wizard—Route Selection Dialog Box
2.
Select the FCIP route you want to remove, then click Finish.
The Security Check dialog box requests the administrator password, as
shown in Figure 7-97.
Figure 7-97 FCIP Route Remove Wizard—Security Check Dialog Box
3.
FI0054601-00 C
Type the appropriate password, then click OK to confirm the removal of the
FCIP route.
7-93
S
7 – SANsurfer iSCSI/FC Router Manager
Wizards
The Add FCIP Route Complete dialog box lets you know when the
configuration is complete, as shown in Figure 7-98.
Figure 7-98 FCIP Route Remove Wizard—Completed Dialog Box
NOTE:
This dialog box may take a few seconds before appearing.
4.
7-94
Click OK to exit the dialog box.
FI0054601-00 C
A
Command Reference
The command line interface (CLI) enables you to perform a variety of router
management tasks through an Ethernet or serial port connection. This section
describes the following:
„
Logging On to a SAN Router
„
Guest Account
„
Working with SAN Router Configurations
„
Commands
Logging On to a SAN Router
To log on to a router using Telnet, open a command line window on the
workstation and enter the Telnet command followed by the router IP address:
# telnet <ip_address>
A Telnet window opens prompting you for a login. Enter an account name and
password.
To log on to a switch through the serial port, configure the workstation port with the
following settings:
„
115200 baud
„
8-bit character
„
1 stop bit
„
No parity
Enter an account name and password when prompted.
FI0054601-00 C
A-1
S
A – Command Reference
Guest Account
Guest Account
Routers come from the factory with the following account already defined:
Account name: guest
Password: password
This guest account provides access to the router and its configuration. After
planning your router management needs, consider changing the password for this
account.
The guest account is automatically closed after 15 minutes of inactivity.
See the Password Command for information about changing passwords.
Working with SAN Router Configurations
Successful management of routers with the command line interface depends on
the effective use of router configurations. Modifying configurations, backing up
configurations, and restoring configurations are key router management tasks.
Modifying a Configuration
The router has three major areas of configuration:
„
„
Management port configuration, which uses the following commands:
„
Set Mgmt Command
„
Show Mgmt Command
ISCSI port configuration, which uses the following commands:
„
Set iSCSI Command
„
Show iSCSI Command
Saving and Restoring Router Configurations
Saving and restoring a configuration can help protect your work or for use as a
template in configuring other routers.
A-2
FI0054601-00 C
A
A – Command Reference
Working with SAN Router Configurations
Save Router Configuration and Persistence
Perform the following steps to save the router’s configuration and persistent data.
Persistent data consists of LUN mappings, discovered FC targets, and discovered
iSCSI initiators.
1.
Execute the Fru save CLI command (see FRU Command) to generate a file
(iSR-6142_FRU.bin) containing the saved data. This file is stored locally
on the router in an FTP directory.
2.
Transfer the saved data from the router to a workstation by executing an
FTP utility on a workstation. The following text is an example of an FTP
transfer to get the saved router configuration data:
c:\>ftp 172.17.137.102
Connected to 172.17.137.102.
220 (none) FTP server (GNU inetutils 1.4.2) ready.
User (172.17.137.102:(none)): ftp
331 Guest login ok, type your name as password.
Password: ftp
230 Guest login ok, access restrictions apply.
ftp> bin
200 Type set to I.
ftp> get iSR-6142_FRU.bin
200 PORT command successful.
150 Opening BINARY mode data connection for
'iSR-6142_FRU.bin' (6168 bytes).
226 Transfer complete.
ftp: 6168 bytes received in 0.00Seconds
6168000.00Kbytes/sec.
ftp> quit
221 Goodbye.
FI0054601-00 C
A-3
A – Command Reference
Working with SAN Router Configurations
S
Restore Router Configuration and Persistence
Perform the following steps to restore the router’s configuration and persistent
data:
1.
Transfer the saved data from a workstation to the router by executing an
FTP utility on the workstation. The following text is an example of an FTP
transfer to put previously saved router configuration data on the router:
c:\>ftp 172.17.137.102
Connected to 172.17.137.102.
220 (none) FTP server (GNU inetutils 1.4.2) ready.
User (172.17.137.102:(none)): ftp
331 Guest login ok, type your name as password.
Password: ftp
230 Guest login ok, access restrictions apply.
ftp> bin
200 Type set to I.
ftp> put iSR-6142_FRU.bin
200 PORT command successful.
150 Opening BINARY mode data connection for
'iSR-6142_FRU.bin'.
226 Transfer complete.
ftp: 6168 bytes sent in 0.00Seconds
6168000.00Kbytes/sec.
ftp> quit
221 Goodbye.
2.
A-4
Execute the Fru restore CLI command (see FRU Command) to update the
router with the saved configuration data. The FRU restore command has the
following two options:
„
Full restore – Restores all router configuration parameters, including IP
addresses, subnet masks, gateways, Local/Remote mappings, and all
other persistent data.
„
Partial restore – Restores only the Local/Remote mappings and
persistent data, such as discovered FC targets and iSCSI initiators.
FI0054601-00 C
A
A – Command Reference
Commands
Commands
The CLI command syntax is as follows:
command
keyword
keyword [value]
keyword [value1] [value2]
The command is followed by one or more keywords. Consider the following rules
and conventions:
„
Commands and keywords are case insensitive.
„
Required keyword values appear in standard font: [value]. Optional values
are shown in italics: [value].
„
Underlined portions of the keyword in the command format indicate the
abbreviated form that can be used. For example, the Delete keyword can be
abbreviated Del.
The command-line completion feature makes entering and repeating commands
easier.Table A-1 describes the command-line completion keystrokes.
Table A-1. Command Line Completion
Keystroke
Effect
Tab
Completes the command line. Enter at least one character
and press the tab key to complete the command line. If
more than one possibility exists, press Tab key again to display all possibilities
Up Arrow
Scrolls backward through the list of previously entered commands.
Down Arrow
Scrolls forward through the list of previously entered commands.
Control-A
Moves cursor to the beginning of the command line.
Control-E
Moves cursor to the end of the command line.
The command set performs monitoring and configuration tasks. Commands
related to monitoring tasks are available to all account names. Commands related
to configuration tasks are available only within an Admin session. An account
must have admin authority to enter the Admin Start command, which opens an
admin session. Refer to the Admin Command.
FI0054601-00 C
A-5
A – Command Reference
Commands
S
Admin Command
Opens and closes an administrator session. You can run any command that
changes the router configuration within an Admin session. Only one Admin
session can be open on the router at any time. An inactive Admin session will time
out after 15 minutes.
Authority
None
Syntax
admin
start (or begin)
end (or stop)
cancel
Keywords
start (or begin)
Opens the Admin session.
end (or stop)
Closes the Admin session. The Logout, Shutdown, and Reset commands will also
end an Admin session.
cancel
Terminates an Admin session opened by another user. Use this keyword with
care, because it terminates the Admin session without warning the other user and
without saving pending changes.
Notes
Closing a Telnet window during an Admin session does not release the session. In
this case, you must either wait for the Admin session to time out, or use the Admin
Cancel command.
Examples
Opening and closing an admin session example:
QRouter #> admin start
Password : ******
QRouter(admin) #>
...
QRouter(admin) #> admin end
QRouter #>
A-6
FI0054601-00 C
A
A – Command Reference
Commands
Beacon Command
Enables or disables the Heartbeat and System Fault LEDs flashing. The
heartbeat and system fault LEDs flash synchronously (on and off, together). No
other LEDs are affected.
Authority
Admin session
Syntax
beacon
on
off
Keywords
on
Turns on the router beacon.
off
Turns off the router beacon.
Examples
Beacon command example:
QRouter #> beacon on
FI0054601-00 C
A-7
A – Command Reference
Commands
S
Clear Command
The clear command provides two operations: it removes all entries from the
router’s log file, or it resets the Fibre Channel and iSCSI statistic counters.
Authority
Admin session
Syntax
clear [logs or stats]
Keywords
logs
Clears all entries from router’s log file.
stats
Resets the statistic counters.
Examples
Clear command example:
QRouter (admin) #> clear logs
QRouter (admin) #> clear stats
A-8
FI0054601-00 C
A
A – Command Reference
Commands
Date Command
This command displays or sets the date and time. To set the date and time, the
information string must be provided in this format: MMDDhhmmCCYY. The new
date and time takes effect immediately.
Authority
Admin session to set the date and time. No authority required to display the
current date and time.
Syntax
date
[MMDDhhmmCCYY]
Keywords
[MMDDhhmmCCYY]
Specifies the date—this requires an Admin session. If you omit
[MMDDhhmmCCYY], the command uses the current date, which does not require
an admin session.
Notes
Network time protocol (NTP) must be disabled to set the time with the Date
command. Refer to the Set NTP Command for information about NTP.
Examples
Date command example:
QRouter
Tue Jan
QRouter
Tue Jan
FI0054601-00 C
(admin) #>
1 14:28:00
(admin) #>
1 14:28:14
date 010314282007
2008
date
2008
A-9
S
A – Command Reference
Commands
FcipRoute Command
The FCIP route command provides for configuring a new FCIP route and
modifying or deleting an existing FCIP route. Each FCIP route requires a
dedicated FC and Gigabit Ethernet port. Configuring an FCIP route, specifying an
FC and GE port pair, take precedence over any previous configuration for the port
pair (FC/GE). This removes the previous configuration of the port pair.
Authority
Admin session.
Syntax
fciproute
add
mod
rm
Keywords
add
The FCIP route add command configures a new FCIP route.
modify
The FCIP route modify command modifies an existing FCIP route.
remove
The FCIP route remove command removes an existing FCIP route.
Examples
FCIP route add command example:
QRouter (admin) #> fciproute add
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE
ports.
Configuring FCIP Route: 1
--------------------------FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled
]
FC Port (1=FC1, 2=FC2, ...)
[FC1
]
GE Port (1=GE1, 2=GE2, ...)
[GE1
]
IP Address (IPv4 or IPv6; 0=IPv6 Link Local)
[0.0.0.0
] 0
Selected IPv6 Link Local Address: fe80::2c0:ddff:fe0c:8be2
A-10
FI0054601-00 C
A
A – Command Reference
Commands
Remote IPv6 Address
fe80::21b:21ff:fe06:d517
[::
]
MTU Size (0=Normal, 1=Jumbo, 2=Other)
[Normal
]
TCP Window Size (0=8KB, 1=16KB, 2=32KB)
[32768
]
Window Scaling (0=Enable, 1=Disable)
[Disabled
]
TCP Port No. (Min=1024, Max=65535)
[3225
]
GE Port Speed (0=Auto, 1=100Mb, 2=1Gb)
[Auto
]
FCIP Time Stamp (0=Enable, 1=Disable)
[Enabled
]
Resource Allocate TimeOut (Min=1sec, Max=5sec)[1
]
Bandwidth, Mbit/sec (Min=1, Max=1000)
[1000
]
VLAN (0=Enable, 1=Disable)
[Disabled
]
FCIP SW Compression (0=Enable, 1=Disable)
[Disabled
]
All attribute values for FCIP Route 1 will now be saved.
FCIP route modify command example:
QRouter (admin) #> fciproute mod
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE
ports.
Route
FC Port ID
GE Port ID
-----
----------
----------
1
FC1
GE1
Please select a FCIP route from the list above ('q' to quit): 1
Configuring FCIP Route: 1
--------------------------FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled
]
IP Address (IPv4 or IPv6; 0=IPv6 Link Local)
]
[::
Selected IPv6 Link Local Address: fe80::2c0:ddff:fe0c:8be2
Remote IPv6 Address [fe80::21b:21ff:fe06:d517]
fe80::21b:21ff:fe06:d514
MTU Size (0=Normal, 1=Jumbo, 2=Other)
FI0054601-00 C
[Normal
]
A-11
S
A – Command Reference
Commands
TCP Window Size (0=8KB, 1=16KB, 2=32KB)
[32768
]
Window Scaling (0=Enable, 1=Disable)
[Disabled
]
TCP Port No. (Min=1024, Max=65535)
[3225
]
GE Port Speed (0=Auto, 1=100Mb, 2=1Gb)
[Auto
]
FCIP Time Stamp (0=Enable, 1=Disable)
[Enabled
]
Resource Allocate TimeOut (Min=1sec, Max=5sec)[1
]
Bandwidth, Mbit/sec (Min=1, Max=1000)
[1000
]
VLAN (0=Enable, 1=Disable)
[Disabled
]
FCIP SW Compression (0=Enable, 1=Disable)
[Disabled
]
All attribute values for FCIP Route 1 will now be saved.
FCIP route remove command example:
QRouter (admin) #> fciproute rm
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE
ports.
Route
FC Port ID
GE Port ID
-----
----------
----------
1
FC1
GE1
Please select a FCIP route from the list above ('q' to quit): 1
FCIP Route 1 has been removed from the system.
A-12
FI0054601-00 C
A
A – Command Reference
Commands
FRU Command
The FRU command saves and restores the router’s configuration.
Authority
Admin session to restore.
Syntax
fru
restore
save
Keywords
restore
The FRU restore command requires that you first ftp the tar file containing the
desired configuration to the router. After issuing this command, you are prompted
for the restore level. You can fully restore the router’s configuration (all
configuration parameters and LUN mappings) or restore only the LUN mappings.
The restored configuration will not take effect until you reboot the router.
save
The FRU save command creates a tar file containing the router’s persistent data,
configuration, and LUN mappings. It stores the file in the router’s /var/ftp directory.
You must then ftp the tar file from the router.
Examples
FRU restore command example:
QRouter (admin) #> fru restore
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Type of restore (0=full, 1=mappings only) [full]
FRU restore completed.
Please reboot the system for configuration to take effect.
FRU save command example:
QRouter (admin) #> fru save
FRU save completed. Configuration File is QLogic_Router_FRU.bin
Please use FTP to extract the file out from the System.
FI0054601-00 C
A-13
S
A – Command Reference
Commands
Help Command
The help command displays a list of the commands and their syntax.
Authority
None
Syntax
help
Examples
Help command example:
QRouter #> help
amin [ cancel | start | end ]
beacon [ on | off ]
date [ <MMDDhhmmCCYY> ]
clear [ logs | stats ]
fciproute [ add | mod | rm ]
discover
fru [ restore | save ]
history
image [ cleanup | list | unpack ]
image cleanup
image list
image unpack [ <filename> ]
initiator [ add | rm ]
localmap [ add | rm ]
logout
passwd
ping
quit
reboot
remotemap [ add | mod | rm ]
remotepeer [ add | rm ]
reset factory
save [ capture | logs | traces ]
set [ chap | fc | features | iscsi
isns | mgmt | ntp | properties
snmp | system ]
set chap
set fc [ <PORT_NUM> ]
set features
set iscsi [ <PORT_NUM> ]
set isns [ <PORT_NUM> ]
set mgmt
set ntp
set properties
set snmp [trap_destinations [ <DEST_NUM> ]]
set system
show [ chap | fc | fciproutes
features | initiators | iscsi
isns | localmaps | logs
A-14
FI0054601-00 C
A
A – Command Reference
Commands
memory | mgmt | ntp
perf | presented_initiators | presented_targets
properties | remotemaps | remotepeers
snmp | stats | system
targets ]
show chap
show fc [ <PORT_NUM> ]
show fciproutes [ <LINK_ID> ]
show features
show initiators [ fc | iscsi ]
show iscsi [ <PORT_NUM> ]
show isns [ <PORT_NUM> ]
show localmaps
show logs
show memory
show mgmt
show ntp
show perf [ byte | init_rbyte | init_wbyte | tgt_rbyte | tgt_wbyte ]
show presented_initiators [ fc | iscsi ]
show presented_targets [ fc | iscsi ]
show properties
show remotemaps
show remotepeers
show snmp
show stats
show system
show targets [ fc | iscsi ]
shutdown
target [ add | rm ]
FI0054601-00 C
A-15
A – Command Reference
Commands
S
History
Displays a numbered list of the previously entered commands.
Authority
None
Syntax
History
Examples
History command example:
QRouter (admin) #> history
1: admin start
2: help
3: history
A-16
FI0054601-00 C
A
A – Command Reference
Commands
Image Command
Updates the router’s firmware image and cleans up (removes) the image files in
the router’s /var/ftp directory.
NOTE:
Use FTP to transfer an image file to the router’s /var/ftp directory.
Authority
Admin session
Syntax
image
cleanup
list
unpack [file]
Keywords
cleanup
Removes all firmware image files in the router’s /var/ftp directory. You can transfer
these are files when updating the router’s firmware image.
list [file]
Displays a list of the firmware image files in the router’s /var/ftp directory.
unpack [file]
Unpacks the firmware image file specified in the [file] parameter and installs the
firmware image on the router. You must reboot the router to activate the new
firmware image.
Image cleanup command example:
QRouter (admin) #> image cleanup
Image list command example:
QRouter (admin) #> image list
isr-6142-2_1_1_0.bin
Image unpack command example:
QRouter (admin) #> image unpack isr-6142-2_1_1_0.bin
Unpack Completed. A reboot is required for the FW to take effect.
Do you wish to reboot the System at the current time (y/n): n
FI0054601-00 C
A-17
A – Command Reference
Commands
S
Initiator Command
Adds, modifies, and removes an initiator in the router’s database.
Authority
Admin session
Syntax
initiator
add
mod
remove
Keywords
add
Adds an initiator the router’s database.
mod
Modifies the settings of an initiator.
remove
Removes an initiator.
Examples
Initiator add command example:
QRouter (admin) #> initiator add
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
iSCSI Initiator Name (Max = 256 characters) [ ]
iqn.1991-05.com.microsoft:qlogic-09sd5i4l
All attribute values for that have been changed will now be saved.
Initiator mod (modify) command example:
QRouter (admin) #> initiator mod
Index (WWNN/iSCSI Name)
----- ----------------0 iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Please select an Initiator from the list above ('q' to quit): 0
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
All attribute values for that have been changed will now be saved.
A-18
FI0054601-00 C
A
A – Command Reference
Commands
Initiator remove command example:
QRouter (admin) #> initiator rm
Index (WWNN/iSCSI Name)
----- ----------------0 iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Please select an Initiator from the list above ('q' to quit): 0 All
attribute values for that have been changed will now be saved.
FI0054601-00 C
A-19
A – Command Reference
Commands
S
Localmap Command
The localmap command maps a locally-connected initiator device to a
locally-connected target device. The initiator and target are not on the same FC
port.
Authority
Admin session
Syntax
localmap
add
rm
Keywords
add
Add local initiator to target mapping.
rm
Remove local initiator to target mapping.
Examples
Localmap add command example with FC port query:
QRouter (admin) #> localmap add
The following wizard will query for attributes before persisting and
activating the updated mapping in the system configuration. If you
wish to terminate this wizard before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 50:06:01:60:b0:22:0c:d1,50:06:01:68:30:22:0c:d1
1 iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Please select an Initiator from the list above ('q' to quit) : 1
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7
1 50:06:01:60:b0:22:0c:d1,50:06:01:68:30:22:0c:d1
2 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0
3 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab
Please select a Target from the list above ('q' to quit) : 3
iSCSI port used to access the Initiator (1=GE1, 2=GE2, ...) : 2
FC port used to access the Target (1=FC1, 2=FC2, ...) : 1
The selected initiator has not been presented on the port that was
selected to access the target. The following steps in the wizard will
now setup the initiator so that it is presented on the port that will
be used to access the target. A default name for the presented
A-20
FI0054601-00 C
A
A – Command Reference
Commands
initiator is assigned below. To accept the default assigned name
simply press the ENTER key or enter a new name.
FC presented initiator WWPN [21:01:00:c0:dd:0c:8b:e2 ] :
The selected target has not been presented on the port that was
selected to be accessed the initiator. The following steps in the
wizard will now setup the target so that it is presented on the port
that will be used by the initiator. A default name for the presented
target is assigned below. To accept the default assigned name simply
press the ENTER key or enter a new name.
iSCSI presented target name
[iqn.2004-08.com.qlogic:isr-6142.0608a00471.1.220000
2037fd8bab.2000002037fd8bab] :
All attribute values for that have been changed will now be saved.
Localmap add command example without FC port query:
QRouter (admin) #> localmap add
The following wizard will query for attributes before persisting and
activating the updated mapping in the system configuration. If you
wish to terminate this wizard before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 50:06:01:60:b0:22:0c:d1,50:06:01:68:30:22:0c:d1
1 iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Please select an Initiator from the list above ('q' to quit) : 1
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7
1 50:06:01:60:b0:22:0c:d1,50:06:01:68:30:22:0c:d1
2 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0
3 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab
Please select a Target from the list above ('q' to quit) : 3
iSCSI port used to access the Initiator (1=GE1, 2=GE2, ...) : 2
The selected initiator has not been presented on the port that was
selected to access the target. The following steps in the wizard will
now setup the initiator so that it is presented on the port that will
be used to access the target. A default name for the presented
initiator is assigned below. To accept the default assigned name
simply press the ENTER key or enter a new name.
FI0054601-00 C
A-21
A – Command Reference
Commands
S
FC presented initiator WWPN [21:01:00:c0:dd:0c:8b:e2 ] :
The selected target has not been presented on the port that was
selected to be accessed the initiator. The following steps in the
wizard will now setup the target so that it is presented on the port
that will be used by the initiator. A default name for the presented
target is assigned below. To accept the default assigned name simply
press the ENTER key or enter a new name.
iSCSI presented target name
[iqn.2004-08.com.qlogic:isr-6142.0608a00471.1.220000
2037fd8bab.2000002037fd8bab] :
All attribute values for that have been changed will now be saved.
Localmap remove command example:
172.17.137.171 (admin) #> localmap rm
The following wizard will query for attributes before persisting and
activating the updated mapping in the system configuration. If you
wish to terminate this wizard before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:14:c3:44:9a:fa,22:00:00:14:c3:44:9a:fa
1 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7
2 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0
3 20:00:00:14:c3:44:9b:9d,22:00:00:14:c3:44:9b:9d
4 20:00:00:14:c3:3d:d2:bf,22:00:00:14:c3:3d:d2:bf
5 20:00:00:14:c3:44:9b:86,22:00:00:14:c3:44:9b:86
6 20:00:00:14:c3:3d:cf:80,22:00:00:14:c3:3d:cf:80
7 20:00:00:14:c3:44:9a:f1,22:00:00:14:c3:44:9a:f1
8 20:00:00:14:c3:44:9b:0b,22:00:00:14:c3:44:9b:0b
9 20:00:00:14:c3:44:9b:7c,22:00:00:14:c3:44:9b:7c
Please select a Target from the list above ('q' to quit): 0 The
following is a list of the initiators that have been mapped to the
selected target and the port that was configured for the initiator to
be presented on in order to access the target.
Target
Index Port Initiator (WWNN,WWPN/iSCSI Name)
----- ------ -------------------------------0 FC1 iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Please select an Initiator to remove ('q' to quit) : 0
All attribute values for that have been changed will now be saved.
A-22
FI0054601-00 C
A
A – Command Reference
Commands
Logout Command
Exits the command line interface and returns you to the login prompt.
Authority
None
Keywords
logout
Examples
Logout command example:
QRouter (admin) #> logout
(none) login:
FI0054601-00 C
A-23
A – Command Reference
Commands
S
Password Command
Changes the guest and administrator passwords.
Authority
Admin session
Syntax
password
Examples
Password command example:
QRouter (admin) #> passwd
Press 'q' and the ENTER key to abort this command.
Select password to change (0=guest, 1=admin) : 1
account OLD password : ******
account NEW password (6-128 chars) : ******
please confirm account NEW password : ******
Password has been changed.
A-24
FI0054601-00 C
A
A – Command Reference
Commands
Ping Command
The ping command verifies the connectivity of each Ethernet port, management,
GE1 (iSCSI 1), and GE2 (iSCSI 2).
Authority
Admin session
Syntax
ping
Examples
Ping command example:
QRouter (admin) #> ping
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
IP Address (IPv4 or IPv6)
fe80::217:a4ff:fe99:c279
[0.0.0.0]
Iteration Count (0=Continuously)
[0
] 10
Outbound Port (0=Mgmt, 1=GE1, 2=GE2, ...) [Mgmt
]
Size Of Packet (Min=1, Max=65486 Bytes)
]
[56
Pinging fe80::217:a4ff:fe99:c279 with 56 bytes of data:
Request timed out.
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.4ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.3ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.3ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.2ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.3ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.3ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.7ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.2ms
Reply from fe80::217:a4ff:fe99:c279: bytes=64 time=0.2ms
Ping Statistics for fe80::217:a4ff:fe99:c279:
Packets:
Sent
= 10,
Received = 9, Lost = 1
Approximate round trip times in milli-seconds:
Minimum = 0.2ms, Maximum = 0.7ms, Average = 0.3ms
FI0054601-00 C
A-25
S
A – Command Reference
Commands
Quit Command
Exits the command line interface and returns you to the login prompt.
Authority
None
Syntax
quit
Examples
Quit command example:
QRouter (admin) #> quit
(none) login:
A-26
FI0054601-00 C
A
A – Command Reference
Commands
Reboot Command
Restarts the router firmware.
Authority
Admin session
Syntax
reboot
Examples
Reboot command example:
QRouter (admin) #> reboot
Are you sure you want to reboot the System (y/n): y
System will now be rebooted...
FI0054601-00 C
A-27
S
A – Command Reference
Commands
Remote Map Command
The remotemap command provides for the mapping of an initiator and target, one
of which is located on a remote system (router). It prompts you to enter the remote
system (router), then lists the devices (initiators and targets) located on the
remote system. You can select a device from the remote system and then the
local system.
Authority
Admin session
Syntax
remotemap
add
mod
rm
Keywords
add
Adds a device mapping, initiator to target, one of which is remote.
mod
Modifies an existing remote device mapping.
rm
Removes a remote device mapping.
Examples
Remotemap add command example:
QRouter (admin) #> remotemap add
The following wizard will create a mapping a device connected to the
local system and a device connected to the selected remote peer
system. If you wish to terminate this wizard before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Index (System Info, Mgmt IP Address)
----- -----------------------------0 iSR-6142.0608A00487(172.17.137.215)
Please select a REMOTE system from the list above ('q' to quit) : 0
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:20:00:d0:b2:02:86:d0,21:20:00:d0:b2:02:86:d0
1 20:21:00:d0:b2:02:86:d0,21:21:00:d0:b2:02:86:d0
2 20:20:00:d0:b2:02:86:d1,21:20:00:d0:b2:02:86:d1
3 20:21:00:d0:b2:02:86:d1,21:21:00:d0:b2:02:86:d1
(Init/Tgt)
(Init/Tgt)
(Init/Tgt)
(Init/Tgt)
Please select a LOCAL device from the list above ('q' to quit) : 0
A-28
FI0054601-00 C
A
A – Command Reference
Commands
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:e0:8b:08:5f:3d,21:00:00:e0:8b:08:5f:3d (Initiator)
1 20:00:00:d0:b2:00:19:f0,21:00:00:d0:b2:00:19:f0 (Init/Tgt)
Please select a REMOTE device from the list above ('q' to quit) : 0
NOTE: Both the LOCAL and REMOTE systems do not have the SMART-WRITE
feature, therefore the querying of the SMART-WRITE settings are not
applicable and will be skipped for this mapping. All attribute values
for that have been changed will now be saved.
Remotemap add command example with SMART-WRITE licenses:
QRouter (admin) #> remotemap add
The following wizard will create a mapping a device connected to the
local system and a device connected to the selected remote peer
system. If you wish to terminate this wizard before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Index (System Info, Mgmt IP Address)
----- -----------------------------0 iSR-6142.0608A00471(172.17.137.143)
Please select a REMOTE system from the list above ('q' to quit) : 0
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:01:00:e0:8b:28:5f:3d,21:01:00:e0:8b:28:5f:3d (Initiator)
1 20:00:00:e0:8b:08:5f:3d,21:00:00:e0:8b:08:5f:3d (Initiator)
Please select a LOCAL device from the list above ('q' to quit) : 0
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:14:c3:3d:d2:bf,22:00:00:14:c3:3d:d2:bf (Target)
1 20:00:00:14:c3:44:9b:86,22:00:00:14:c3:44:9b:86 (Target)
2 20:00:00:14:c3:44:9b:9d,22:00:00:14:c3:44:9b:9d (Target)
3 20:00:00:14:c3:44:9a:fa,22:00:00:14:c3:44:9a:fa (Target)
4 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7 (Target)
5 20:00:00:20:37:fd:8a:b0,22:00:00:20:37:fd:8a:b0 (Target)
6 20:00:00:14:c3:3d:cf:80,22:00:00:14:c3:3d:cf:80 (Target)
7 20:00:00:14:c3:44:9a:f1,22:00:00:14:c3:44:9a:f1 (Target)
8 20:00:00:14:c3:44:9b:0b,22:00:00:14:c3:44:9b:0b (Target)
9 20:00:00:14:c3:44:9b:7c,22:00:00:14:c3:44:9b:7c (Target)
10 20:00:00:20:37:fd:8b:ab,22:00:00:20:37:fd:8b:ab (Target)
Please select a REMOTE device from the list above ('q' to quit) : 0
FI0054601-00 C
A-29
S
A – Command Reference
Commands
Smart-Write (0=Enable, 1=Disable) [Enabled ]
Smart-Write Compression (0=Enable, 1=Disable) [Disabled ]
Smart-Write Load Balance (0=Enable, 1=Disable) [Disabled ]
All attribute values for that have been changed will now be saved.
Remotemap add command example wihout SMART-WRITE licenses:
QRouter (admin) #> remotemap add
The following wizard will create a mapping a device connected to the
local system and a device connected to the selected remote peer
system. If you wish to terminate this wizard before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Index (System Info, Mgmt IP Address)
----- -----------------------------0 iSR-6142.0608A00487(172.17.137.215)
Please select a REMOTE system from the list above
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:20:00:d0:b2:02:86:d0,21:20:00:d0:b2:02:86:d0
1 20:21:00:d0:b2:02:86:d0,21:21:00:d0:b2:02:86:d0
2 20:20:00:d0:b2:02:86:d1,21:20:00:d0:b2:02:86:d1
3 20:21:00:d0:b2:02:86:d1,21:21:00:d0:b2:02:86:d1
('q' to quit) : 0
(Init/Tgt)
(Init/Tgt)
(Init/Tgt)
(Init/Tgt)
Please select a LOCAL device from the list above ('q' to quit) : 0
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:e0:8b:08:5f:3d,21:00:00:e0:8b:08:5f:3d (Initiator)
1 20:00:00:d0:b2:00:19:f0,21:00:00:d0:b2:00:19:f0 (Init/Tgt)
Please select a REMOTE device from the list above ('q' to quit) : 0
NOTE: Both the LOCAL and REMOTE systems do not have the SMART-WRITE
feature, therefore the querying of the SMART-WRITE settings are not
applicable and will be skipped for this mapping. All attribute values
for that have been changed will now be saved.
Remotemap modify command example with SMART-WRITE licenses:
QRouter (admin) #> remotemap mod
The following wizard will be used to modify various settings of a
remote mapping. If you wish to terminate this wizard before reaching
the end of the list press 'q' or 'Q' and the ENTER key to do so.
Index Local Device (WWPN) Remote Device (WWPN)
----- ------------------- -------------------0 21:00:00:e0:8b:08:5f:3d 22:00:00:20:37:fd:8a:b0
A-30
FI0054601-00 C
A
A – Command Reference
Commands
Please select a remote mapping from the list above ('q' to quit): 0
Smart-Write Compression (0=Enable, 1=Disable) [Disabled ] 1
Smart-Write Load Balance (0=Enable, 1=Disable) [Enabled ] 1
All attribute values for that have been changed will now be saved.
Remotemap modify command example without SMART-WRITE licenses:
QRouter (admin) #> remotemap mod
The following wizard will be used to modify various settings of a
remote mapping. If you wish to terminate this wizard before reaching
the end of the list press 'q' or 'Q' and the ENTER key to do so.
Index Local Device (WWPN)
----- ------------------0 21:20:00:d0:b2:02:86:d0
1 21:21:00:d0:b2:02:86:d0
2 21:20:00:d0:b2:02:86:d1
3 21:21:00:d0:b2:02:86:d1
4 21:20:00:d0:b2:02:86:d0
Remote Device (WWPN)
-------------------21:00:00:d0:b2:00:19:f0
21:00:00:d0:b2:00:19:f0
21:00:00:d0:b2:00:19:f0
21:00:00:d0:b2:00:19:f0
21:00:00:e0:8b:08:5f:3d
Please select a remote mapping from the list above ('q' to quit): 0
The SMART-WRITE feature license in not applicable for the selected
mapping. Only mappings with the SMART-WRITE feature can be modified by
this command.
Command aborted.
Remotemap remove command example:
QRouter (admin) #> remotemap rm
The following wizard will query for attributes before persisting and
activating the updated mapping in the system configuration. If you
wish to terminate this wizard before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
Index Local Device (WWPN) Remote Device (WWPN)
----- ------------------- -------------------0 21:00:00:e0:8b:08:5f:3d 22:00:00:14:c3:44:9a:fa
Please select a remote mapping from the list above ('q' to quit): 0
All attribute values for that have been changed will now be saved.
FI0054601-00 C
A-31
A – Command Reference
Commands
S
Remote Peer Command
The remotepeer command lets you assign a router peer to a local router, which
can have up to four peers.
Authority
Admin session
Syntax
remotepeer
add
rm
Keywords
add
Add a peer router.
rm
Remove a peer router.
Examples
Remotepeer add command example:
QRouter (admin) #> remotepeer add
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
REMOTE MGMT port IP Address [0.0.0.0] 172.17.137.143
Contacting REMOTE system (timeout=120 seconds) ...
<Admin> password of REMOTE system: ******
<Admin> password confirmed.
Remote System Information
------------------------Product Name iSR-6142
Symbolic Name
Serial Number 0608A00471
HW Version 3
SW Version 2.3.0.1
No. of iSCSI Ports 2
iSCSI Base Name iqn.2004-08.com.qlogic:isr-6142.0608a00471
Mgmt IP Address 172.17.137.143
iSCSI Port 1 IP Address 10.3.5.106
iSCSI Port 1 TCP Port No. 3260
iSCSI Port 2 IP Address 10.3.5.107
iSCSI Port 2 TCP Port No. 3260
Do you wish to create a connection with the REMOTE system (y/n): y
All attribute values for that have been changed will now be saved.
A-32
FI0054601-00 C
A
A – Command Reference
Commands
Remotepeer remove command example:
QRouter (admin) #> remotepeer rm
Index (System Info, Mgmt IP Address)
----- -----------------------------0 iSR-6142.0608A00487(172.17.137.215)
Please select a remote system from the list above ('q' to quit): 0
WARNING:
Remote mappings exist between the LOCAL system and the selected REMOTE
system. Removing this REMOTE system will also remove these mappings.
Do you wish to continue the 'remotepeer rm' operation (y/n): y All
attribute values for that have been changed will now be saved.
FI0054601-00 C
A-33
A – Command Reference
Commands
S
Reset Factory Command
Restores the router configuration parameters to the factory default values. It
deletes all LUN mappings, as well as all persistent data regarding targets, LUNs,
and initiators. It also restores the factory default IP addresses.
Authority
Admin session
Syntax
reset
factory
Keywords
factory
Restores the router to factory default configuration.
Examples
Reset command example:
QRouter (admin) #> reset factory
Are you sure you want to restore to factory default settings (y/n): y
Please reboot the System for the settings to take effect.
A-34
FI0054601-00 C
A
A – Command Reference
Commands
Save Command
Saves logs and traces.
Authority
Admin session
Syntax
save
capture
logs
traces
Keywords
capture
The save capture command creates a debug file that captures all debug dump
data. After the command completes, you must ftp the debug capture file from the
router.
logs
The save logs command creates a tar file containing the router’s log data, storing
the file in the router’s /var/ftp directory. After the command completes, you must
ftp the log’s tar file from the router.
traces
The save traces command creates a tar file containing the router’s dump data,
storing the tar file in the router’s /var/ftp directory. After the command completes,
you must ftp the trace’s tar file from the router. If the router does not have any
dump data, you will be notified when executing this command. The system
creates an event log entry whenever it generates dump data.
Examples
Save capture command example:
QRouter (admin) #> save capture
Debug capture completed. Package is System_Capture.tar.gz
Please use FTP to extract the file out from the System.
Save logs command example:
QRouter (admin) #> save logs
Save Event Logs completed. Package is Router_Evl.tar.gz
Please use FTP to extract the file out from the System.
FI0054601-00 C
A-35
A – Command Reference
Commands
S
Two Save traces command examples:
QRouter (admin) #> save traces
Save ASIC Traces completed. Package is Router_Asic_Trace.tar.gz
Please use FTP to extract the file out from the System.
QRouter (admin) #> save traces
No ASIC trace files exist to save. Command aborted.
A-36
FI0054601-00 C
A
A – Command Reference
Commands
Set Command
Configures general router parameters as well as parameters that are specific to
the Fibre Channel, iSCSI, and management ports.
Authority
Admin session
Syntax
set
chap
fc [port_num]
features
Iscsi [port_num]
Isns [port_num]
mgmt
ntp
properties
snmp
system
Keywords
chap
Sets the CHAP secrets.
fc [port_num]
Sets the Fibre Channel port parameters.
features
Sets licensed router features such as SmartWrite or additional host ports.
iscsi [port_num]
Sets the iSCSI port parameters.
isns [port_num]
Sets the iSNS parameters.
mgmt
Sets the management port parameters.
ntp
Sets the network time protocol (NTP) parameters.
properties
Sets CLI properties.
snmp
Sets the simple network management protocol (SNMP) parameters.
FI0054601-00 C
A-37
A – Command Reference
Commands
S
system
Sets system parameters such as symbolic name and log level.
A-38
FI0054601-00 C
A
A – Command Reference
Commands
Set CHAP Command
Configures general router parameters.
Authority
Admin session
Syntax
set chap
Examples
Set CHAP command example:
QRouter (admin) #> set chap
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0
iqn.2004-08.com.qlogic.isr-6142.0539A01064.0.2000002037fd8bab.2200002
037fd8bab
1
iqn.2004-08.com.qlogic.isr-6142.0539A01064.1.2000002037fd8bab.2200002
037fd8bab
Please select a presented target from the list above ('q' to quit): 0
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
CHAP (0=Enable, 1=Disable) [Disabled]
All attribute values for that have been changed will now be saved.
FI0054601-00 C
A-39
A – Command Reference
Commands
S
Set FC Command
Configures a Fibre Channel port.
Authority
Admin session
Syntax
set fc [port_num]
Keywords
[port_num]
The number of the FC port to be configured.
Examples
Set FC command example:
QRouter (admin) #> set fc 1
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both ports.
Configuring FC Port: 1
------------------------Port Status (0=Enable, 1=Disable) [Enabled ]
Link Rate (0=Auto, 1=1Gb, 2=2Gb, 4=4Gb) [Auto ]
Frame Size (0=512B, 1=1024B, 2=2048B) [2048 ]
Execution Throttle (Min=16, Max=256) [64 ]
Programmed Connection Option:
(0=Loop Only, 1=P2P Only, 2=Loop Pref) [Loop Pref ]
All attribute values for Port 1 that have been changed will now be
saved.
A-40
FI0054601-00 C
A
A – Command Reference
Commands
Set Features Command
The set features command lets you enter licensed router features such as
SmartWrite or additional host ports.
NOTE:
The date and time must be set prior to entering feature license keys.
Authority
Admin session
Syntax
set features
Examples
Set Features command example:
QRouter (admin) #> set features
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value.
If you wish to terminate this process before reaching the end of the
list press 'q' or 'Q' and the ENTER key to do so. Enter feature key to
be saved/activated: 1-LCWC6XKAFKC7S-SMART_WRITE
Please reboot the system for these changes to take effect.
FI0054601-00 C
A-41
S
A – Command Reference
Commands
Set iSCSI Command
Configures an iSCSI port.
Authority
Admin session
Syntax
set iscsi [port_num]
Keywords
[port_num]
The number of the iSCSI port to be configured.
Examples
Set iSCSI command example:
QRouter (admin) #> set iscsi 1
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both
ports.
Configuring iSCSI Port: 1
---------------------------
A-42
Port Status (0=Enable, 1=Disable)
[Enabled
]
IP Address
[0.0.0.0
]
Subnet Mask
[0.0.0.0
]
Gateway IP Address
[0.0.0.0
]
Target TCP Port No. (Min=1024, Max=65535)
[3260
]
MTU Size (0=Normal, 1=Jumbo, 2=Other)
[Normal
]
Window Size (0=8KB, 1=16KB, 2=32KB)
[32768
]
Window Scaling (0=Enable, 1=Disable)
[Enabled
]
Window Scaling Factor (Min=0, Max=5)
[1
]
Port Speed (0=Auto, 1=100Mb, 2=1Gb)
[Auto
]
Header Digests (0=Enable, 1=Disable)
[Enabled
]
Data Digests (0=Enable, 1=Disable)
[Enabled
]
VLAN (0=Enable, 1=Disable)
[Disabled
]
IPv6 Address 1
2001::1234
[::
]
IPv6 Address 2
[::
]
IPv6 Default Router
[::
]
FI0054601-00 C
A
A – Command Reference
Commands
IPv6 Tgt TCP Port No. (Min=1024, Max=65535) [3260
]
IPv6 Window Scaling (0=Enable, 1=Disable)
[Enabled
]
IPv6 Window Scaling Factor (Min=0, Max=5)
[1
]
IPv6 VLAN (0=Enable, 1=Disable)
[Disabled
]
All attribute values for Port 1 that have been changed will now be
saved.
FI0054601-00 C
A-43
S
A – Command Reference
Commands
Set iSNS Command
Configures iSNS parameters for an iSCSI port.
Authority
Admin session
Syntax
set isns [port_num]
Keywords
[port_num]
The number of the iSCSI port to be configured for iSNS.
Examples
Set iSNS command example:
QRouter (admin) #> set isns 1
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Configuring iSNS iSCSI Port: 1
-------------------------------iSNS (0=Enable, 1=Disable)
[Disabled
] 0
iSNS Address (IPv4 or IPv6)
fe80::21b:21ff:fe06:d517
[0.0.0.0
]
TCP Port No.
[3205
]
All attribute values for Port 1 that have been changed will now be
saved.
A-44
FI0054601-00 C
A
A – Command Reference
Commands
Set Mgmt Command
Configures the router’s management port (10/100).
Authority
Admin session
Syntax
set mgmt
Examples
Set Mgmt command example:
QRouter (admin) #> set mgmt
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to the MGMT
port.
IPv4 Interface (0=Enable, 1=Disable)[Enabled ]
IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp)[Dhcp ]
IPv6 Interface (0=Enable, 1=Disable)[Enabled ]
IPv6 Mode (0=Manual, 1=AutoConfigure)[Manual ] 1
All attribute values that have been changed will now be saved.
FI0054601-00 C
A-45
A – Command Reference
Commands
S
Set NTP Command
Use the set NTP command to configure the network time protocol parameters.
NTP sets the date and time on the router from a network time server.
Authority
Admin session
Syntax
set ntp
Examples
Set NTP command example:
QRouter (admin) #> set ntp
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
NTP (0=Enable, 1=Disable) [Enabled ]
TimeZone Offset from GMT (Min=-12hrs,Max=12hrs) [-8 ]
IP Address [0] [0.0.0.0 ] 207.126.97.57
IP Address [1] [0.0.0.0 ]
IP Address [2] [0.0.0.0 ]
All attribute values that have been changed will now be saved.
A-46
FI0054601-00 C
A
A – Command Reference
Commands
Set Properties Command
Configures the CLI (command line interface) properties.
Authority
Admin session
Syntax
set properties
Examples
Set Properties command example:
QRouter (admin) #> set properties
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
CLI Inactivty Timer (0=Disable, 1=15min, 2=60min) [Disabled]
CLI Prompt (Max=32 Characters) [QRouter ] RTR1
All attribute values that have been changed will now be saved.
FI0054601-00 C
A-47
S
A – Command Reference
Commands
Set SNMP Command
Configures the general simple network management protocol (SNMP) properties,
as well as configuring eight trap destinations.
Authority
Admin session
Syntax
set snmp
trap_destinations
Keywords
trap_destinations
Specifies the setting of the trap destinations.
Examples
Set SNMP command example for setting the general properties:
QRouter (admin) #> set snmp
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Configuring SNMP:
----------------Read Community [ ] Public
Trap Community [ ] Private
System Location [ ]
System Contact [ ]
Authentication Traps (0=Enable, 1=Disable) [Disabled ]
All attribute values that have been changed will now be saved.
Set SNMP command example for configuring an SNMP trap destination:
QRouter (admin) #> set snmp trap_destinations
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
Configuring SNMP Trap Destination 1 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ] 0
IP Address [0.0.0.0 ] 10.0.0.5
Destination Port [0 ] 1024
Trap Version [0 ] 2
Configuring SNMP Trap Destination 2 :
A-48
FI0054601-00 C
A
A – Command Reference
Commands
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
Configuring SNMP Trap Destination 3 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
Configuring SNMP Trap Destination 4 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
Configuring SNMP Trap Destination 5 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
Configuring SNMP Trap Destination 6 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
Configuring SNMP Trap Destination 7 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
Configuring SNMP Trap Destination 8 :
------------------------------------Destination enabled (0=Enable, 1=Disable) [Disabled ]
All attribute values that have been changed will now be saved.
FI0054601-00 C
A-49
A – Command Reference
Commands
S
Set System Command
Configures the general router parameters.
Authority
Admin session
Syntax
set system
Examples
Set System command example:
QRouter (admin) #> show system
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
System Symbolic Name (Max = 64 characters) [ ]
System Log Level (Min = 0, Max = 3) [0 ]
All attribute values that have been changed will now be saved.
A-50
FI0054601-00 C
A
A – Command Reference
Commands
Show Command
Displays router operational information.
Authority
None
Syntax
show
chap
fc [port_num]
fciproutes [link_id]
features
initiators [fc or iscsi]
iscsi [port_num]
isns [port_num]
localmaps
logs
memory
mgmt
ntp
perf [ byte | init_rbyte | init_wbyte | tgt_rbyte | tgt_wbyte ]
presented_initiators [ fc | iscsi ]
presented_targets [fc or iscsi]
properties
remotemaps
remotepeers
snmp
stats
system
targets [fc or iscsi]
Keywords
chap
Displays Chap information.
fc [port_num]
Displays Fibre Channel port information.
fciproutes [link_id]
Displays FCIP routes in effect and their configuration parameters.
features
Displays installed licenses (port / SmartWrite).
initiators [fc or iscsi]
Displays SCSI initiator information: iSCSI or FC.
FI0054601-00 C
A-51
S
A – Command Reference
Commands
iscsi [port_num]
Displays iSCSI port information and configuration.
isns [port_num]
Displays the router’s iSCSI name server (iSNS) configuration.
localmaps
Displays local mappings, FC to FC, iSCSI to FC, and FC to iSCSI.
logs
Displays contents of the router logs.
memory
Displays memory managed by router. Includes total and available.
mgmt
Displays the router’s management port (10/100) configuration.
ntp
Displays the router’s network time protocol (NTP) configuration.
perf
Displays router performance data.
presented_initiators
Displays initiators presented by the router.
presented_targets [fc or iscsi]
Displays targets presented by the router: FC, iSCSI, or both.
properties
Displays the router’s CLI (command line interface) properties.
remotemaps
Displays all remote maps that have been configured.
remotepeers
Displays all remote peers.
snmp
Displays the router’s simple network management protocol (SNMP) properties
and trap configurations.
stats
Displays the router statistics, both FC and iSCSI.
A-52
FI0054601-00 C
A
A – Command Reference
Commands
system
Displays router product information including serial number, software version,
hardware version, configuration, and temperature.
targets [fc or iscsi]
Displays targets discovered by the router: FC, iSCSI, or both.
FI0054601-00 C
A-53
A – Command Reference
Commands
S
Show CHAP Command
Displays CHAP configuration.
Authority
None
Syntax
show chap
Examples
Show CHAP command example:
QRouter #> show chap
The following is a list of iSCSI nodes that have been configured with
CHAP 'ENABLED':
Type iSCSI Node
-------- -----------No entires found.
A-54
FI0054601-00 C
A
A – Command Reference
Commands
Show FC Command
Displays Fibre Channel port information for the specified port. If you do not specify
the port, it displays both ports.
Authority
None
Syntax
show fc [port_num]
Keywords
[port_num]
The number of the FC port to display.
Examples
Show FC command example:
QRouter (admin) #> show fc
FC Port Information
--------------------FC Port 1
Port Status Enabled
Link Status Up
Current Link Rate 2Gb
Programmed Link Rate Auto
WWNN 20:00:00:c0:dd:0c:8b:e2
WWPN 21:00:00:c0:dd:0c:8b:e2
Port ID 02-02-ef
Firmware Revision No. 3.03.07
Frame Size 2048
Execution Throttle 64
Connection Mode Loop
Programmed Connection Option Loop Preferred
FC Port 2
Port Status Enabled
Link Status Up
Current Link Rate 2Gb
Programmed Link Rate Auto
WWNN 20:00:00:c0:dd:0c:8b:e3
WWPN 21:00:00:c0:dd:0c:8b:e3
Port ID 02-06-ef
Firmware Revision No. 3.03.07
Frame Size 2048
Execution Throttle 64
Connection Mode Loop
Programmed Connection Option Loop Preferred
FI0054601-00 C
A-55
S
A – Command Reference
Commands
Show FcipRoutes Command
Displays FCIP route(s) configuration parameters.
Authority
None
Syntax
show fciproutes [link_id]
Keywords
[link_id]
The number of the FCIP route to be displayed (1 or 2).
Examples
Show FCIP routes command example:
QRouter (admin) #> show fciproutes
FCIP Route Information
------------------------
A-56
FCIP Route
1
FCIP Interfaces Status
Enabled
FCIP Link Status
Down
FC Port
FC1
GE Port
GE1
GE Link Status
Up
IPv6 Link Local
fe80::2c0:ddff:fe0c:8be2
IPv6 Remote Address
fe80::21b:21ff:fe06:d517
MTU Size
Normal
TCP Window Size
32768
Window Scaling
Disabled
TCP Port No
3225
GE Port Speed
Auto
FCIP Time Stamp
Enabled
Error Detect TimeOut
1
Resource Allocate TimeOut
1
Bandwidth, Mbit/sec
1000
VLAN
Disabled
FCIP SW Compression
Disabled
FI0054601-00 C
A
A – Command Reference
Commands
Show Features Command
The show features command displays the licensed features that have been
enabled on the router.
Authority
None
Syntax
show features
Examples
Show Features command example:
QRouter (admin) #> show features
Feature Key Information
------------------------Key 7-LC7D9RMLD05XI-iSR-6142 (SMART-WRITE,39_HOSTS,62_HOSTS)
Date Applied Mon Jun 19 10:08:21 2007
FI0054601-00 C
A-57
A – Command Reference
Commands
S
Show Initiators Command
Displays SCSI initiator information for iSCSI, FC, or both.
Authority
None
Syntax
show initiators
fc
iscsi
Keywords
fc
Specifies the display of Fibre Channel initiators.
iscsi
Specifies the display of iSCSI initiators.
Examples
Show Initiators command example:
QRouter #> show initiators
Initiator Information
----------------------Initiator Name iqn.1991-05.com.microsoft:qlogic-8qdaqlxt
Alias
IP Address 10.3.5.130
Portal No. 1
Status Logged In
A-58
FI0054601-00 C
A
A – Command Reference
Commands
Show iSCSI Command
Displays iSCSI information for the specified port. If you do not specify the port, this
command displays both ports.
Authority
None
Syntax
show iscsi [port_num]
Keywords
[port_num]
The number of the iSCSI port to display.
Examples
Show iSCSI port command example:
QRouter (admin) #> show iscsi
iSCSI Port Information
-----------------------iSCSI Port
1
Port Status
Enabled
Link Status
Up
iSCSI Base Name
iqn.2004-08.com.qlogic:isr-6142.0608a00471.0
FI0054601-00 C
MAC Address
00-c0-dd-0c-8b-e2
IP Address
0.0.0.0
Subnet Mask
0.0.0.0
Gateway IP Address
0.0.0.0
Firmware Revision No.
3.00.02.44
No. of Open Connections
0
Target TCP Port No.
3260
MTU Size
Normal
Window Size
32768
Window Scaling
Enabled
Window Scaling Factor
1
Current Port Speed
1Gb/FDX
Programmed Port Speed
Auto
Header Digests
Enabled
Data Digests
Enabled
Max Burst
262144
Max First Burst
65536
VLAN
Disabled
IPv6 Address 1
::
IPv6 Address 2
::
A-59
S
A – Command Reference
Commands
IPv6 Link Local
fe80::2c0:ddff:fe0c:8be2
IPv6 Default Router
::
IPv6 Target TCP Port No.
3260
IPv6 Window Scaling
Enabled
IPv6 Window Scaling Factor 1
IPv6 VLAN
Disabled
iSCSI Port
2
Port Status
Enabled
Link Status
Up
iSCSI Base Name
iqn.2004-08.com.qlogic:isr-6142.0608a00471.1
MAC Address
00-c0-dd-0c-8b-e3
IP Address
0.0.0.0
Subnet Mask
0.0.0.0
Gateway IP Address
0.0.0.0
Firmware Revision No.
3.00.02.44
No. of Open Connections
0
Target TCP Port No.
3260
MTU Size
Normal
Window Size
32768
Window Scaling
Enabled
Window Scaling Factor
1
Current Port Speed
1Gb/FDX
Programmed Port Speed
Auto
Header Digests
Enabled
Data Digests
Enabled
Max Burst
262144
Max First Burst
65536
VLAN
Disabled
IPv6 Address 1
::
IPv6 Address 2
::
IPv6 Link Local
fe80::2c0:ddff:fe0c:8be3
IPv6 Default Router
::
IPv6 Target TCP Port No.
3260
IPv6 Window Scaling
Enabled
IPv6 Window Scaling Factor 1
IPv6 VLAN
A-60
Disabled
FI0054601-00 C
A
A – Command Reference
Commands
Show iSNS Command
Displays iSNS configuration information for the specified iSCSI port. If you do not
specify the port, this command displays the iSNS configuration information for
both iSCSI ports.
Authority
None
Syntax
show isns [port_num]
Keywords
[port_num]
The iSCSI port number whose iSNS configuration you want to display.
Examples
Show iSNS command example:
QRouter (admin) #> show isns
iSNS Information
------------------
FI0054601-00 C
iSCSI Port
1
iSNS
Enabled
IPv6 Address
fe80::21b:21ff:fe06:d517
TCP Port No.
3205
iSCSI Port
2
iSNS
Disabled
IP Address
0.0.0.0
TCP Port No.
3205
A-61
S
A – Command Reference
Commands
Show Localmaps Command
The show localmaps command displays all local mappings on the router. Local
mappings are mappings between initiator and target devices.
Authority
None
Syntax
show localmaps
Examples
Show Localmaps command example:
QRouter (admin) #> show localmaps
Local Mappings
---------------Initiator iqn.1991-05.com.microsoft:qlogic-09sd5i4l
Target 20:00:00:20:37:fd:9c:f7,22:00:00:20:37:fd:9c:f7
Initiator Port GE2
Target Port FC1
Initiator 20:01:00:e0:8b:28:5f:3d,21:01:00:e0:8b:28:5f:3d
Target 20:00:00:00:87:1d:fa:64,22:00:00:00:87:1d:fa:64
Initiator Port FC2
Target Port FC2
A-62
FI0054601-00 C
A
A – Command Reference
Commands
Show Logs Command
Displays the router event log.
Authority
None
Syntax
show logs
Examples
Show Logs command example:
QRouter #> show logs
01/01/2008
01/01/2008
01/01/2008
01/01/2008
FI0054601-00 C
00:00:13
00:00:21
00:00:13
00:00:22
System
QL4022
System
QL4022
3
3
3
3
Tuesday 01 January 12:13 AM
#0: QLIsrDecodeMailbox: Link up
Tuesday 01 January 12:13 AM
#0: QLIsrDecodeMailbox: Link up
A-63
A – Command Reference
Commands
S
Show Memory Command
Displays the router’s memory usage. If there are no configured FCIP routes, it
shows the FCIP memory usage of zero.
Authority
None
Syntax
show memory
Examples
Show Memory command example with no FCIP routes configured:
QRouter #> show memory
Memory Units Free/Total
-------------- ---------Physical 15MB/505MB
Buffer Pool 11520/12544
Process Blocks 8192/8192
Request Blocks 8192/8192
Event Blocks 1024/1024
Control Blocks 256/256
FCIP Buffer Pool 0/0
FCIP Request Blocks 16384/16384
Show Memory command example with one FCIP route configured:
QRouter #> show memory
Memory Units Free/Total
-------------- ---------Physical 28MB/251MB
Buffer Pool 2176/4224
Process Blocks 4096/4096
Request Blocks 4096/4096
Event Blocks 512/512
Control Blocks 128/128
FCIP Buffer Pool 13320/16384
FCIP Request Blocks 15368/16384
A-64
FI0054601-00 C
A
A – Command Reference
Commands
Show Mgmt Command
Displays the router’s management port (10/100) configuration.
Authority
None
Syntax
show mgmt
Examples
Show Mgmt command example:
QRouter (admin) #> show mgmt
Management Port Information
-----------------------------
FI0054601-00 C
IPv4 Interface
Enabled
IPv4 Mode
Dhcp
IPv4 IP Address
172.17.137.129
IPv4 Subnet Mask
255.255.254.0
IPv4 Gateway
172.17.136.1
IPv6 Interface
Disabled
Link Status
Up
MAC Address
00-c0-dd-0c-8b-e1
A-65
A – Command Reference
Commands
S
Show NTP Command
Displays the router’s network time protocol (NTP) configuration.
Authority
None
Syntax
show ntp
Examples
Show NTP command example:
QRouter #> show ntp
NTP Information
----------------Mode Disabled
Status Offline
TimeZone Offset (Hours) 0
A-66
FI0054601-00 C
A
A – Command Reference
Commands
Show Performance Command
Displays router performance data.
Authority
None
Syntax
show perf
byte
init_rbyte
init_wbyte
tgt_rbyte
tgt_wbyte
Keywords
byte
Displays data transfer rate of each port (FC and GE).
init_rbyte
Displays initiator read transfer rate per port.
init_wbyte
Displays initiator write transfer rate per port.
tgt_rbyte
Displays target read transfer rate per port.
tgt_wbyte
Displays target write transfer rate per port.
Examples
Show Performance (all) command example:
QRouter #> show perf
Port Bytes/s Bytes/s Bytes/s Bytes/s Bytes/s
Number (init_r) (init_w) (tgt_r) (tgt_w) (total)
------ -------- -------- -------- -------- -------GE1 0 0 22M 26M 48M
GE2 0 0 49M 50M 99M
FC1 50M 52M 0 0 103M
FC2 20M 28M 0 0 49M
FI0054601-00 C
A-67
A – Command Reference
Commands
S
Show Performance byte command example:
QRouter #> show perf byte
Displaying bytes/sec (total)... (Press any key to stop display)
GE1 GE2 FC1 FC2
-----------------------------47M 93M 94M 48M
47M 94M 96M 47M
46M 96M 96M 47M
45M 94M 97M 48M
47M 92M 93M 48M
45M 93M 94M 46M
A-68
FI0054601-00 C
A
A – Command Reference
Commands
Show Presented Initiators Command
Displays initiators presented by the router: FC.
Authority
None
Syntax
show presented_initiators
Examples
Show Presented Initiators command example:
QRouter #> show presented_initiators
Presented Initiator Information
--------------------------------FC Presented Initiators
------------------------WWNN 20:01:00:c0:dd:0c:8b:e3
WWPN 21:01:00:c0:dd:0c:8b:e3
Port FC2
<MAPS TO>
WWNN 20:01:00:e0:8b:28:5f:3d
WWPN 21:01:00:e0:8b:28:5f:3d
WWNN 20:01:00:c0:dd:0c:8b:e2
WWPN 21:01:00:c0:dd:0c:8b:e2
Port FC1
<MAPS TO>
Name iqn.1991-05.com.microsoft:qlogic-09sd5i4l
FI0054601-00 C
A-69
A – Command Reference
Commands
S
Show Presented Targets Command
Displays targets presented by the router: FC, iSCSI, or both.
Authority
None
Syntax
show presented_targets
fc
iscsi
Keywords
fc
Specifies the display of FC presented targets.
iscsi
Specifies the display of iSCSI presented targets.
Examples
Show Presented Targets command example where the interface is not
specified:
QRouter #> show presented_targets
Presented Target Information
-----------------------------FC Presented Targets
---------------------WWNN 20:01:00:c0:dd:0c:8b:e3
WWPN 21:01:00:c0:dd:0c:8b:e3
Port FC2
<MAPS TO>
WWNN 20:00:00:00:87:1d:fa:64
WWPN 22:00:00:00:87:1d:fa:64
iSCSI Presented Targets
------------------------Name
iqn.2004-08.com.qlogic:isr-6142.0608a00471.1.2200002037fd9cf7.2000002
037fd9cf7
Port GE2
<MAPS TO>
WWNN 20:00:00:20:37:fd:9c:f7
WWPN 22:00:00:20:37:fd:9c:f7
The following is an example of the Show Presented FC Targets command:
QRouter #> show presented_targets fc
No Presented Targets found.
A-70
FI0054601-00 C
A
A – Command Reference
Commands
Show Presented iSCSI Targets command example:
QRouter #> show presented_targets iscsi
Presented Target Information
-----------------------------iSCSI Presented Targets
------------------------Name
iqn.2000-04.com.qlogic:isr6142:0.50001fe150069d20.50001fe150069d2c
IP 10.3.5.66
<MAPS TO>
WWNN 50:00:1f:e1:50:06:9d:20
WWPN 50:00:1f:e1:50:06:9d:2c
Name
iqn.2000-04.com.qlogic:isr6142:1.50001fe150069d20.50001fe150069d2c
IP 10.3.5.67
<MAPS TO>
WWNN 50:00:1f:e1:50:06:9d:20
WWPN 50:00:1f:e1:50:06:9d:2c
Name
iqn.2000-04.com.qlogic:isr6142:0.50001fe150011150.50001fe150011158
IP 10.3.5.66
<MAPS TO>
WWNN 50:00:1f:e1:50:01:11:50
WWPN 50:00:1f:e1:50:01:11:58
Name
iqn.2000-04.com.qlogic:isr6142:1.50001fe150011150.50001fe150011158
IP 10.3.5.67
<MAPS TO>
WWNN 50:00:1f:e1:50:01:11:50
WWPN 50:00:1f:e1:50:01:11:58
FI0054601-00 C
A-71
A – Command Reference
Commands
S
Show Properties Command
Displays the router’s CLI (command line interface) properties.
Authority
None
Syntax
show properties
Examples
Show Properties command example:
QRouter #> show properties
CLI Properties
---------------Inactivty Timer Disabled
Prompt String QRouter
A-72
FI0054601-00 C
A
A – Command Reference
Commands
Show Remotemaps Command
Displays all remote maps that have been configured.
Authority
None
Syntax
show remotemaps
Examples
Show Remotemaps command example:
QRouter #> show remotemaps
Remote Mappings
----------------Local Device 20:01:00:e0:8b:28:5f:3d,21:01:00:e0:8b:28:5f:3d
(Initiator)
Remote Device 20:00:00:14:c3:3d:d2:bf,22:00:00:14:c3:3d:d2:bf
(Target)
Local Port FC2
FC1
Remote System iSR-6142.0608A00471(172.17.137.143)
Status Online
Smart-Write Enabled
Compression Disabled
Load Balance Disabled
FI0054601-00 C
A-73
S
A – Command Reference
Commands
Show Remotepeers Command
The show remotepeers commands displays all remote peers.
Authority
None
Syntax
show remotepeers
Examples
Show Remotepeers command example:
QRouter #> #> show remotepeers
Remote System Information
------------------------Product Name iSR-6142
Symbolic Name
Serial Number 0608A00487
HW Version 3
SW Version 2.2.0.4
No. of iSCSI Ports 2
iSCSI Base Name iqn.2004-08.com.qlogic:isr-6142.0608a00487
Mgmt IP Address 172.17.137.215
iSCSI Port 1 IP Address 10.3.5.103
iSCSI Port 1 TCP Port No. 3260
iSCSI Port 2 IP Address 10.3.5.104
iSCSI Port 2 TCP Port No. 3260
A-74
FI0054601-00 C
A
A – Command Reference
Commands
Show SNMP Command
Displays the router’s simple network management protocol (SNMP) and any
configured traps.
Authority
None
Syntax
show snmp
Examples
Show SNMP command example:
QRouter #> show snmp
SNMP Configuration
-----------------Read Community Public
Trap Community Private
System Location
System Contact
Authentication traps Disabled
System OID 1.3.6.1.4.1.3873.1.5
System Description iSR-6142
Trap Destination 1
-----------------IP Address 10.0.0.5
Trap Port 1024
Trap Version 2
FI0054601-00 C
A-75
A – Command Reference
Commands
S
Show Stats Command
Displays the router statistics: FC and iSCSI.
Authority
None
Syntax
show stats
Examples
Show Statistics command example:
QRouter #> show stats
FC Port Statistics
-------------------FC Port 1
Interrupt Count 23
Target Command Count 0
Initiator Command Count 0
FC Port 2
Interrupt Count 1717443350
Target Command Count 0
Initiator Command Count 1815115822
iSCSI Port Statistics
----------------------iSCSI Port 1
Interrupt Count 3108358287
Target Command Count 1815115673
Initiator Command Count 0
MAC Xmit Frames 54392137663
MAC Xmit Byte Count 61199467593726
MAC Xmit Multicast Frames 0
MAC Xmit Broadcast Frames 0
MAC Xmit Pause Frames 0
MAC Xmit Control Frames 0
MAC Xmit Deferrals 0
MAC Xmit Late Collisions 0
MAC Xmit Aborted 0
MAC Xmit Single Collisions 0
MAC Xmit Multiple Collisions 0
MAC Xmit Collisions 0
MAC Xmit Dropped Frames 0
MAC Xmit Jumbo Frames 0
MAC Rcvd Frames 42061498217
MAC Rcvd Byte Count 60362392962831
MAC Rcvd Unknown Control Frames 0
MAC Rcvd Pause Frames 0
MAC Rcvd Control Frames 0
MAC Rcvd Dribbles 0
MAC Rcvd Frame Length Errors 0
MAC Rcvd Jabbers 0
A-76
FI0054601-00 C
A
A – Command Reference
Commands
MAC Rcvd Carrier Sense Errors 0
MAC Rcvd Dropped Frames 0
MAC Rcvd CRC Errors 0
MAC Rcvd Encoding Errors 0
MAC Rcvd Length Errors Large 1
MAC Rcvd Small Errors Small 0
MAC Rcvd Multicast Frames 34394
MAC Rcvd Broadcast Frames 33144
iSCSI Port 2
Interrupt Count 51604
Target Command Count 0
Initiator Command Count 0
MAC Xmit Frames 0
MAC Xmit Byte Count 0
MAC Xmit Multicast Frames 0
MAC Xmit Broadcast Frames 0
MAC Xmit Pause Frames 0
MAC Xmit Control Frames 0
MAC Xmit Deferrals 0
MAC Xmit Late Collisions 0
MAC Xmit Aborted 0
MAC Xmit Single Collisions 0
MAC Xmit Multiple Collisions 0
MAC Xmit Collisions 0
MAC Xmit Dropped Frames 0
MAC Xmit Jumbo Frames 0
MAC Rcvd Frames 186
MAC Rcvd Byte Count 39260
MAC Rcvd Unknown Control Frames 0
MAC Rcvd Pause Frames 0
MAC Rcvd Control Frames 0
MAC Rcvd Dribbles 0
MAC Rcvd Frame Length Errors 0
MAC Rcvd Jabbers 0
MAC Rcvd Carrier Sense Errors 0
MAC Rcvd Dropped Frames 0
MAC Rcvd CRC Errors 0
MAC Rcvd Encoding Errors 0
MAC Rcvd Length Errors Large 0
MAC Rcvd Small Errors Small 0
MAC Rcvd Multicast Frames 94
MAC Rcvd Broadcast Frames 91
iSCSI Shared Statistics
----------------------PDUs Xmited 2729500577
Data Bytes Xmited 55036896842234
PDUs Rcvd 2655246170
Data Bytes Rcvd 0
I/O Completed 1815115669
FI0054601-00 C
A-77
A – Command Reference
Commands
S
Unexpected I/O Rcvd 0
iSCSI Format Errors 0
Header Digest Errors 0
Data Digest Errors 0
Sequence Errors 0
PDU Xmit Count 2729500577
PDU Xmit Count 2729500577
PDU Xmit Count 2729500577
IP Xmit Packets 54392134283
IP Xmit Byte Count 59132566295008
IP Xmit Fragments 0
IP Rcvd Packets 42061430681
IP Rcvd Byte Count 58764046068744
IP Rcvd Fragments 0
IP Datagram Reassembly Count 0
IP Error Packets 0
IP Fragment Rcvd Overlap 0
IP Fragment Rcvd Out of Order 0
IP Datagram Reassembly Timeouts 0
TCP Xmit Segment Count 54392134284
TCP Xmit Byte Count 57389353022514
TCP Rcvd Segment Count 42061430681
TCP Rcvd Byte Count 57418079800284
TCP Persist Timer Expirations 0
TCP Rxmit Timer Expired 116
TCP Rcvd Duplicate Acks 986657165
TCP Rcvd Pure Acks 816265831
TCP Xmit Delayed Acks 3584507
TCP Rcvd Pure Acks 177811024
TCP Rcvd Segment Errors 0
TCP Rcvd Segment Out of Order 1
TCP Rcvd Window Probes 0
TCP Rcvd Window Updates 18500272
TCP ECC Error Corections 0
A-78
FI0054601-00 C
A
A – Command Reference
Commands
Show System Command
Displays router product information including the serial number, software version,
hardware version, configuration, and temperature.
Authority
None
Syntax
show system
Examples
Show System command example:
QRouter #> show system
System Information
-------------------Product Name
iSR-6142
Symbolic Name
FI0054601-00 C
Serial Number
0608A00471
HW Version 5
(IPv6 Supported)
SW Version
2.4.2.0rc2
No. of FC Ports
2
No. of iSCSI Ports
2
Temperature (C)
31
A-79
A – Command Reference
Commands
S
Show Targets Command
Displays targets the router discovered: FC, iSCSI, or both.
Authority
None
Syntax
show targets
fc
iscsi
Keywords
fc
Specifies the display of FC targets.
iscsi
Specifies the display of iSCSI targets.
Examples
Show FC Targets command example:
QRouter #> show targets fc
Target Information
-------------------WWNN 50:00:1f:e1:50:01:11:50
WWPN 50:00:1f:e1:50:01:11:58
Port ID 01-0d-00
Portal No. 1
State Online
WWNN 50:00:1f:e1:50:06:9d:20
WWPN 50:00:1f:e1:50:06:9d:2c
Port ID 01-08-00
Portal No. 1
State Online
Show iSCSI Targets command example:
QRouter #> show targets iscsi
No Targets found.
A-80
FI0054601-00 C
A
A – Command Reference
Commands
Show VLAN Command
Displays the router’s VLAN configuration.
Authority
None
Syntax
show vlan [port_num]
Keywords
[port_num]
The iSCSI port number whose VLAN configuration you want to display.
Examples
Show VLAN command example:
QRouter #> show vlan
VLAN Information
-----------------Port 1
VLAN Disabled
ID 0
Priority 0
Port 2
VLAN Disabled
ID 0
Priority 0
QRouter #> show vlan 1
VLAN Information
-----------------Port 1
VLAN Disabled
ID 0
Priority 0
FI0054601-00 C
A-81
A – Command Reference
Commands
S
Shutdown Command
The shutdown command provides for an orderly shutdown of the routers firmware.
It does not power down the router.
Authority
Admin session
Syntax
shutdown
Examples
Shutdown command example:
QRouter (admin) #> shutdown
A-82
FI0054601-00 C
A
A – Command Reference
Commands
Target Command
Removes targets from the router’s database. Typically, you can use this command
to remove targets from the database that are no longer connected to the router.
The target add command is not currently supported.
Authority
Admin session
Syntax
target
add
rm
Keywords
add
Not supported
rm
Remove a target from the router’s target database.
Examples
Target add command example:
QRouter (admin) #> target add
Command 'target add' is currently not supported.
Target rm (remove) command example:
QRouter (admin) #> target rm
Index (WWNN,WWPN/iSCSI Name)
----- ---------------------0 20:00:00:20:37:fd:8b:ab:00:00:00:00:fc:b6:1f:fa
Please select an 'OFFLINE' Target from the list above ('q' to quit): q
Command aborted.
FI0054601-00 C
A-83
S
A – Command Reference
Commands
Traceroute Command
Prints the route a network packet takes to the reach the destination specified by
the user.
Authority
Admin session
Syntax
traceroute
Examples
Traceroute command example:
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current
value. If you wish to terminate this process before reaching the end
of the list press 'q' or 'Q' and the ENTER key to do so.
IP Address (IPv4 or IPv6)
[0.0.0.0] 172.17.136.18
Outbound Port (0=Mgmt, 1=GE1, 2=GE2, ...) [Mgmt
]
Tracing route to 172.17.136.18 over a maximum of 30 hops:
1
172.17.136.18
2.3ms
0.2ms
0.2ms
Traceroute completed in 1 hops.
A-84
FI0054601-00 C
B
Log Messages
Log Data
The router maintains a message log you can retrieve and review using either the
command line interface or the SANsurfer Router Manager. The message log is
persistent, maintained across router power cycles and reboots. The three log
message categories are:
„
Informational
„
Error
„
Fatal
The following sections describe the log message categories.
Informational Log Messages
The following sections list and describe the informational log messages by
reporting module.
Application Modules
The application modules generate the informational log messages listed in
Table B-1 and described following the table.
Table B-1. Application Modules—Informational Log Messages
ID
FI0054601-00 C
Log Message
No.
53254
System (router) Booting up
6
53357
QLBA_ProcessTpb: De-compression failed. Disabling
compression temporarily
109
54274
QLFC_Login: Origin 0x%x, VP Index 0x%x, Id 0x%x
1026
54275
QLFC_Login: Port ID %.2x%.2x%.2x
1027
54276
QLFC_Login: Node
Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x
1028
54277
QLFC_Login: Port
Name %.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x
1029
B-1
S
B – Log Messages
Informational Log Messages
Table B-1. Application Modules—Informational Log Messages (Continued)
ID
B-2
Log Message
No.
54306
QLFC_Logout: Origin 0x%x, VP Index 0x%x, Id 0x%x
1058
54307
QLFC_Logout: Port ID %.2x%.2x%.2x
1059
54308
QLFC_Logout: Node Name
%.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x
1060
54309
QLFC_Logout: Port Name
%.2x%.2x%.2x%.2x%.2x%.2x%.2x%.2x
1061
54359
QLFC_HandleTeb: FC Login. VP 0x%x
1111
54368
QLFC_CreateVirtualInitiatorObject: Maximum host (%d) limit
reached.
1120
54938
QLIS_HandleTeb: UTM_EC_OPEN_CONNECTION
1690
54939
QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION or
UTM_EC_CONNECTION_CLOSED
1691
54940
QLIS_HandleTeb: UTM_EC_CONNECTION_OPENED
1692
54941
QLIS_HandleTeb:iSNS Server Open Connection succeeded
1693
54943
QLIS_HandleTeb: UTM_EC_ISNS_SCN
1695
54945
QLIS_HandleTeb: UTM_EC_ISNS_CLIENT_DISCOVERED
1697
54947
QLIS_HandleTeb: UTM_EC_CLOSE_CONNECTION
1699
54948
QLIS_HandleTeb: UTM_EC_CONNECTION_CLOSED
1700
54963
QLIS_SetDdbEntryContinue:[%d:%d] Remote system connection
established
1715
54986
QLIS_HandleSessionTimer: Re-enabling compression
1738
55299
QLSC_CollectBUVUIO: Freeing dead TRB: State 0x%02X,
AbortReason %d, Flags 0x%02X
2051
6
Router is booting up.
109
De-compression failed and will be temporarily disabled.
1026
FC login occurred, origin xx (1 = HBA, 2 = target, 3 = initiator), VP (virtual port)
xx, ID (loop ID) xx.
1027
FC login occurred with port ID xx.xx.xx.
FI0054601-00 C
A
FI0054601-00 C
B – Log Messages
Informational Log Messages
1028
FC login occurred with WWNN xx.xx.xx.xx.xx.xx.xx.xx.
1029
FC login occurred with WWPN xx.xx.xx.xx.xx.xx.xx.xx.
1058
FC logout occurred, origin xx (1 = HBA, 2 = target, 3 = initiator), VP (virtual port)
xx, ID (loop ID) x.
1059
FC logout occurred with port ID xx.xx.xx.
1060
FC logout occurred with WWNN xx.xx.xx.xx.xx.xx.xx.xx.
1061
FC logout occurred with WWPN xx.xx.xx.xx.xx.xx.xx.xx.
1111
FC login event notification, VP (virtual port) xx.
1120
Maximum number of support hosts dd has been reached.
1690
Event notification: iSCSI open connection request.
1691
Event notification: iSCSI close connection request or connection closed.
1692
Event notification: iSCSI connection opened.
1693
Event notification: connection opened with iSNS server.
1695
Event notification: iSNS SCN received.
1697
Event notification: iSNS client discovered.
1699
iSCSI close connection request received.
1700
iSCSI connection closed.
1715
Remote system connection established using DDB d:d.
1738
Re-enabling compression.
2051
TRB freed, State xx, Abort Reason d, Flags xx.
B-3
S
B – Log Messages
Informational Log Messages
iSCSI Driver
The following informational log messages are common to both iSCSI ports: 1
(GE1) and 2 (GE2). The messages are listed in Table B-2 and described following
the table. Log messages beginning with #0 denote iSCSI port 1 (GE1) and log
messages beginning with #1 denote iSCSI port 2 (GE2).
Table B-2. iSCSI Driver—Informational Log Messages
ID
B-4
Log Message
No.
86343
#%d: QLPortUp: Set link configuration 0x%x
327
86347
#%d: QLDisable: Restart RISC
331
86349
#%d: QLEnable: Restart RISC to update EEPROM
333
86352
#%d: QLPortDown: Set link configuration 0x%x
336
86874
#%d: QLIsrDecodeMailbox: Link up
858
327
iSCSI port enabled, port up.
331
Restart iSCSI processor (RISC).
333
EEPROM updated, restart iSCSI processor (RISC).
336
iSCSI port disabled, port down.
858
Link up reported by iSCSI processor for GE1 or GE 2.
FI0054601-00 C
A
B – Log Messages
Informational Log Messages
Fibre Channel Driver
The following informational log messages are common to both Fibre Channel
ports: 1 (FC1) and 2 (FC2). The messages are listed in Table B-3 and described
following the table. Log messages beginning with #0 denote fibre channel port 1
(FC1). Log messages beginning with #1 denote fibre channel port 2 (FC2).
Table B-3. Fibre Channel Driver—Informational Log Messages
ID
FI0054601-00 C
Log Message
No.
118882
#%d: QLIoctlDisable: Reset adapter
98
119088
#%d: QLIsrEventHandler: LIP occurred (%x): mailbox1 = %x
304
119089
#%d: QLIsrEventHandler: LIP reset occurred (%x): mailbox1
= %x
305
119090
#%d: QLIsrEventHandler: Link up (%x) mailbox1 = %x
306
119092
#%d: QLIsrEventHandler: Link mode up (%x): RunTimeMode=%x
308
119093
#%d: QLIsrEventHandler: RSCN update (%x) rscnInfo: %x
309
119097
#%d: QLIsrEventHandler: Port update (%x) mb1-3 %x %x %x
313
119552
#%d: QLFcipIsrEventHandler: Link up (%x) mailbox1 = %x
768
119553
#%d: QLFcipIsrEventHandler: Link down (%x)
769
119554
#%d: QLFcipIsrEventHandler: Link mode up (%x)
770
98
Request to reset the FC processor (adapter) received from IOCTL interface.
304
Fibre Channel loop initialization procedure (LIP) occurred. The LIP type is
reported, as is the contents of the FC processor’s mailbox 1 register.
305
Fibre Channel LIP reset occurred. The LIP reset type is reported, as is the
contents of the FC processor’s mailbox 1 register.
306
Fibre Channel link up occurred. Event status is reported, as is the contents
of the FC processor’s mailbox 1 register.
308
Fibre Channel link up occurred. Event status is reported, as is the
RunTimeMode (0 = loop, 1 = point-to-point).
309
A RSCN was received. Event status is reported, as is the RSCN information.
313
Fibre Channel port update. Event status is reported, as is the contents of the
FC processor’s mailbox 1, 2, and 3 registers.
B-5
S
B – Log Messages
Informational Log Messages
768
FCIP - Fibre Channel link up occurred. Event status is reported, as is the
contents of the FC processor’s mailbox 1 register.
769
FCIP - Fibre Channel link down occurred.
770
FCIP - Fibre Channel link up occurred. Event status is reported, as is the
RunTimeMode (0 = loop, 1 = point-to-point).
User Modules
The user modules generate the log messages listed in Table B-4 and described in
the following table.
Table B-4. User Modules—Informational Log Messages
ID
B-6
Log Message
No.
151842
FW Upgrade performed: new version is: %d.%d.%d.%d
290
151843
REBOOT/SHUTDOWN Command from user. Code=%d
291
151889
#%d: qapisetfcinterfaceparams_1_svc: FC port configuration
changed
337
151890
#%d: qapisetiscsiinterfaceparams_1_svc: iSCSI port
configuration changed
338
151891
#%d: qapisetisns_1_svc:iSNS configuration changed
339
151892
qapisetntpparams_1_svc: NTP configuration changed
340
151893
#%d: qapisetvlanparams_1_svc: VLAN configuration changed
341
151896
qapisetmgmintfcparams_1_svc:Management port configuration
changed
344
151897
qapisetbridgebasicinfo_1_svc:Bridge configuration changed
345
151898
qapimapremote_1_svc: Remotemap added for local device
%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
346
151899
qapimapremote_1_svc: Remotemap added to remote device
%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
347
151900
qapiunmapremote_1_svc: Remotemap removed for local device
%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
348
151901
qapiunmapremote_1_svc: Remotemap removed to remote
device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
349
151902
qapimaptargettoinitiator_1_svc: Localmap added for initiator
%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
350
FI0054601-00 C
A
B – Log Messages
Informational Log Messages
Table B-4. User Modules—Informational Log Messages (Continued)
FI0054601-00 C
ID
Log Message
No.
151903
qapimaptargettoinitiator_1_svc: Localmap added to target device
%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
351
151904
qapiunmaptargettoinitiator_1_svc: Localmap removed for initiator
device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
352
151905
qapiunmaptargettoinitiator_1_svc: Localmap removed to target
device %.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x:%.2x
353
151906
qapimaptargettoinitiator_1_svc: Localmap added for initiator %s
354
151907
qapiunmaptargettoinitiator_1_svc: Localmap removed for initiator
%s
355
151908
GE%d: Port status changed by user to ENABLED.
356
151909
GE%d: Port status changed by user to DISABLED.
357
151910
FC%d: Port status changed by user to ENABLED.
358
151911
FC%d: Port status changed by user to DISABLED.
359
152069
qapisetfcipparams_1_svc: FCIPROUTE %d Added
517
152070
qapisetfcipparams_1_svc: FCIPROUTE %d Modified
518
152071
qapisetfcipparams_1_svc: FCIPROUTE %d Removed
519
290
Performed router firmware upgrade, new version number is d.d.d.d.
291
User performed a router reboot or shutdown.
337
FC port configuration has been modified.
338
iSCSI port configuration has been modified.
339
iSNS configuration has been modified.
340
NTP configuration has been modified.
341
VLAN configuration has been modified.
344
Management ethernet port configuration has been modified.
345
Router configuration has been modified.
346
Remotemap added for local FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
347
Remotemap added for remote FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
B-7
S
B – Log Messages
Informational Log Messages
348
Remotemap removed for local FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
349
Remotemap removed for remote FC device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
350
Localmap added for FC initiator WWPN xx.xx.xx.xx.xx.xx.xx.xx.
351
Localmap added to FC target device WWPN xx.xx.xx.xx.xx.xx.xx.xx.
352
Localmap removed for FC initiator.
353
Localmap removed to FC target device.
354
Localmap added for iSCSI initiator "iqn.dddd-dd.ttt.ttt.ttt.......".
355
Localmap removed for iSCSI initiator "iqn.dddd-dd.ttt.ttt.ttt.......".
356
User enabled GE port d.
357
User disabled GE port d.
358
User enabled FC port d.
359
User disabled FC port d.
517
FCIP route #d added.
518
FCIP route #d modified.
519
FCIP route #d removed.
FCIP
The FCIP module generates the informational log messages listed in Table B-5
and described following the table.
Table B-5. FCIP—Informational Log Messages
ID
B-8
Log Message
No.
184524
qlFcip_Linkchange#%d: GigE Link Down
204
184525
qlFcip_Linkchange#%d: GigE Link Up
205
204
FCIP Route GigE link d (1 or 2) is down.
205
FCIP Route GigE link d (1 or 2) is up.
FI0054601-00 C
A
B – Log Messages
Informational Log Messages
TOE Driver
The TOE driver generates the informational log messages listed in Table B-6 and
described following the table.
Table B-6. TOE—Informational Log Messages
ID
217350
262
Log Message
QL3022:eth%x: Interface is down
No.
262
The GigE interface d (0 or 1) used for an FCIP route is down.
System
The system modules generate the informational log messages listed in Table B-7
and described following the table.
Table B-7. System—Informational Log Messages
ID
249862
6
FI0054601-00 C
Log Message
“Temperature is back to normal range %d\n"
No.
6
The router temperature has returned to the normal operating range and is d (C).
B-9
S
B – Log Messages
Error Log Messages
Error Log Messages
The following sections list and describe the error log messages by reporting
module.
Application Modules
The application modules generate the error log messages listed in Table B-8 and
described following the table.
Table B-8. Application Module—Error Log Messages
ID
B-10
Log Message
No.
40967
QLBA_NullDoorbell: driver unloaded, port disabled
7
40996
QLBA_ProcessTrb: Processing unsupported ordered tag
command
36
41004
QLBA_ProcessTrb: Processing unsupported head of queue tag
command
44
41058
QLBA_CreateTargetDeviceObject: Too many devices
98
41060
QLBA_CreateTargetNodeObject: Too many devices
100
41067
QLBA_CreateLunObject: LunObject memory unavailable
107
41077
QLBA_CreateInitiatorObject: Too many initiators
117
41096
QLBA_DisplayTargetOperationStatus: PCI Error, Status 0x%.2x
136
41106
QLBA_DisplayInitiatorOperationStatus: DMA Error, Status
0x%.2x
146
41107
QLBA_DisplayInitiatorOperationStatus: Transport Error, Status
0x%.2x
147
41111
QLBA_DisplayInitiatorOperationStatus: Data Overrun, Status
0x%.2x
151
41234
QLIS_LoginPduContinue: Operation failed. Initiator 0x%x, TPB
status 0x%x
274
41238
QLKV_ValidateLoginTransitCsgNsgVersion failed (status 0x%x)
278
41257
QLIS_LoginPduContinue: Invalid initiator name. Initiator:
297
41265
QLIS_LoginPduContinue: Target not configured for Portal
305
41267
QLIS_LoginPduContinue: Target not found. Target name:
307
41268
QLIS_LoginPduContinue: Missing target name
308
FI0054601-00 C
A
B – Log Messages
Error Log Messages
Table B-8. Application Module—Error Log Messages (Continued)
FI0054601-00 C
ID
Log Message
No.
41270
QLIS_LoginPduContinue: TSIH is 0 but InitiatorName key/value
not provided
310
41272
QLIS_LoginPduContinue: CONN_STATE_IN_LOGIN, Unknown
InitTaskTag
312
41283
QLIS_LoginPduContinue: TSIH 0x%x out of range
323
41284
QLIS_LoginPduContinue: Session does not exist, invalid TSIH
0x%x
324
41353
QLIS_LoginPduContinue CHAP Validation Failure
393
41354
QLIS_LoginPduContinue Unexpected CHAP key detected
394
41508
QLBI_SetPortInfo: QLUT_AllocatePortalObject failed (PortType
0x%x, PortId 0x%x)
548
41626
QLBI_GetLunInfo: INQUIRY failed, TPB status 0x%x
666
41629
QLBI_GetLunInfo: QLBI_PassthruCommand failed for INQUIRY
(page code 0x83)
669
41635
QLBI_GetLunInfo: QLBI_PassthruCommand failed for READ
CAPACITY
675
41636
QLBI_GetLunInfo: READ CAPACITY failed, TPB status 0x%x
676
41696
QLBI_PassthruCommandCompletion: Passthru command
aborted
736
41700
QLBI_Passthru: Invalid CDB length %d bytes
740
41701
QLBI_Passthru: Invalid data length %d bytes
741
41717
QLBI_PassthruCommand: command interrupted or timed out
757
41750
QLBI_Ioctl: ERROR: Operation (0x%x) not supported in this mode
790
41768
QLBI_GetLunList: REPORT LUNS command failed
808
41769
QLBI_GetLunList: REPORT LUNS command failed with CHECK
CONDITION, SCSI STATUS 0x%02X
809
41771
QLBI_GetLunList: Lun allocation failed for LunId %d
811
41994
QLFC_Login: VpIndex (%d) out of range
1034
41995
QLFC_Login: VP Index 0x%x not configured
1035
42002
QLFC_Login: Can't open connection
1042
B-11
S
B – Log Messages
Error Log Messages
Table B-8. Application Module—Error Log Messages (Continued)
ID
B-12
Log Message
No.
42024
QLFC_Logout: No active path to device. WWPN:
%.2X%.2X%.2X%.2X%.2X%.2X%.2X%.2X
1064
42027
QLFC_Logout: VP Index 0x%x not configured
1067
42068
QLFC_HandleTeb: System Error
1108
42069
QLFC_HandleTeb: Driver Fatal Error
1109
42072
QLFC_HandleTeb: FC Logout
1112
42242
QLIS_AllocateSessionObject: Out of session resources
1282
42252
QLIS_EnqueueiScsiPdu: Duplicate PDU, CmdSN %d (0x%x),
dropping it
1292
42258
QLIS_InstantiateSession: Can't add Initiator to the database
1298
42404
QLIS_ProcessStartTrb: [%d] CmdSN %ld is out of range (%ld
- %ld), Cdb[0] 0x%02X, DataXferLen 0x%x.
1444
42648
QLIS_HandleTeb: Driver Fatal Error
1688
42649
QLIS_HandleTeb: Unload Driver
1689
42654
QLIS_HandleTeb: iSNS Connection Failed
1694
43012
QLSC_CollectBUVUIO: Allocation of DSD failed
2052
43013
QLSC_CollectBUVUIORecover: Allocation of DSD failed
2053
43265
QLUT_AllocateTpbExtension: TPB allocation failed
2305
43267
QLUT_AllocateTpbExtension: Data buffer allocation failed (length
%d)
2307
43268
QLUT_AllocateTpbExtension: Alloc of DSD failed for buffer len
%d
2308
43269
QLFCIP_IncomingFrame: BUGCHECK: Trb (0x%p) ValidFlag
(0x%x) Direction (0x%x)
2309
43270
QLFCIP_IncomingFrame: GetFcipMapPortal failed
2310
43271
QLFCIP_IncomingFrame: Got Status aborted
pTrb->pBufDescList[0]:%p Trb Direction:0x%x
2311
43272
QLFCIP_SystemError: System error
2312
43273
QLFCIP_SystemError: QLOP_IssuePortEnable failed
2313
FI0054601-00 C
A
B – Log Messages
Error Log Messages
Table B-8. Application Module—Error Log Messages (Continued)
ID
FI0054601-00 C
Log Message
No.
43280
QLFCIP_HandleTeb: Driver Fatal error
2320
43281
QLFCIP_ConfigPortal: Find portal object failed for
QLUT_TYPE_FC, PortId (%d)
2321
43282
QLFCIP_ConfigPortal: QLFCIP_ConfigPortal: Invalid PortId for
FCIP link PortID(%d)
2322
43283
QLUT_AllocateFcipTrbPool: Allocation failed (size 0x%x))
2323
43284
QLUT_GetFcipTrb: Null portal object in map table
2324
43285
QLUT_GetFcipTrb: Unable to get the Free Trb
2325
43286
QLUT_GetFcipTrb: Duplicate allocation of FcipTrb (0x%p)
2326
43287
QLUT_FreeFcipTrb: Null portal object in map table
2327
43288
QLUT_FreeFcipTrb: Duplicate Free of FcipTrb (0x%p)
2328
43289
QLUT_InitializeFcipBufDescPool: Memory allocation for
FCIP_BUF_EXT_DESC failed (size 0x%x)
2329
43296
QLUT_FreeFcipDataBuffers: Duplicate Freeing of DataBuf
(0x%p)
2336
43297
QLUT_AllocateFcipDataBuffers: Duplicate allocation of
DataBuffer (0x%p)
2337
43298
QLUT_AllocateFcipDataBuffer: Got NULL PORTAL Object in map
table MEM LEAK!!!!!
2338
43299
QLUT_DeallocateFcipDataBuffer: Null portal object in map table
2339
43300
QLUT_CreateFcipDataBufferpool: Allocation of 32K buffers from
LargeBufferPool failed
2340
43521
QLSC_BreakupVUIOAllocPhase: TPB allocation failed
2561
43522
QLSC_BreakupVUIOAllocPhase: Data buffer and TPB allocation
failed
2562
7
NULL doorbell routine for unloaded drivers. When a driver is unloaded, the
doorbell routine is redirected to this NULL routine.
36
Processing unsupported ordered tag task management command.
44
Processing unsupported head-of-queue task management command.
B-13
S
B – Log Messages
Error Log Messages
B-14
98
Unable to create an object for the target device: exceeded the maximum
number of target devices.
100
Unable to create an object for the target node: exceeded the maximum
number of target devices.
107
Memory unavailable for LUN object.
117
Unable to create an object for initiator object: exceeded the maximum number
of initiators.
136
Process control block status indicates that a PCI error occurred during a target
operation.
146
Process control block status indicates that a DMA error occurred during an
initiator operation.
147
Process control block status indicates that a transport error (protocol)
occurred during an initiator operation.
151
Process control block status indicates that a data overrun error occurred
during an initiator operation.
274
iSCSI login failed between receipt of PDU and request for the data segment.
278
iSCSI login failed due to unsupported version number in received login PDU.
297
iSCSI Login PDU contains invalid initiator name. The format and character
set used to form the initiator name is invalid.
305
iSCSI target login was attempted to a portal (iSCSI1 or iSCSI2) on which the
target is not presented.
307
iSCSI Login PDU received for a target with a target name unknown to the
router.
308
iSCSI Login PDU received without a target name for a normal session.
310
iSCSI Login PDU received without an initiator name key/value.
312
iSCSI Login PDU received with an incorrect initiator task tag for a session
which is partially logged in. This would occur if a login PDU other than the
initial login PDU used an initiator task tag which was different than the initiator
task tag provided in the initial login PDU.
323
iSCSI Login PDU was received with a TSIH out of range. This would occur if
the iSCSI initiator attempting the login failed to used the TSIH value provided
in the Target Login Response PDU (router is target) in subsequent login PDUs.
FI0054601-00 C
A
FI0054601-00 C
B – Log Messages
Error Log Messages
324
iSCSI Login PDU was received with an invalid TSIH value. The TSIH is invalid
because there is no session with that TSIH value. This would occur if the
iSCSI initiator attempting the login failed to used the TSIH value provided in
the target login response PDU (router is target) in subsequent login PDUs.
393
CHAP validation failed during login.
394
Unexpected CHAP key.
548
Failed to allocate an object for Set Port Info IOCTL processing:
PortType: 0 = FC, 1 = iSCSI
PortId: 0 = FC1 or iSCSI1(GE1), 1 = FC2 or iSCSI2 (GE2)
666
Inquiry command failed. The Inquiry command was issued by the router as
part of its discovery process.
669
Pass-Through command for Inquiry command for page 83 failed. The Inquiry
command was issued by the router as part of its discovery process.
675
Pass-Through command for Read Capacity command failed. The Read
Capacity command was issued by the router as part of its discovery process.
676
Read Capacity command failed. The Read Capacity command was issued
by the router as part of its discovery process.
736
Pass-Through command issued by management application (such as
SANsurfer Router Manager) was aborted.
740
Pass-Through command issued by management application (such as
SANsurfer Router Manager) failed due to invalid CDB length.
741
Pass-Through command issued by management application (such as
SANsurfer Router Manager) failed due to invalid data length.
757
Pass-Through command issued by management application (such as
SANsurfer Router Manager) was interrupted or timed out.
790
IOCTL operation unsupported. Operation code provided in log message.
808
Report LUNs command failed. The Report LUNs command was issued by
the router as part of its discovery process.
809
Report LUNs command failed with check condition status. The Report LUNs
command was issued by the router as part of its discovery process.
811
Failed to allocate LUN object: out of resources.
1034
Login attempted using Fibre Channel virtual port (VP) index that is
out-of-range (range = 0–31). Index reported in log message.
1035
Login attempted using Fibre Channel VP index that has not been configured.
Operation attempted on an unconfigured VP.
B-15
S
B – Log Messages
Error Log Messages
B-16
1042
Attempting login but Fibre Channel connection cannot be opened.
1064
Attempting logout of device for which there is no active path (WWPN not
found).
1067
Logout attempted using Fibre Channel VP index that has not been configured.
Operation attempted on an unconfigured VP.
1108
Event notification: Fibre Channel processor encountered a system error
(unrecoverable firmware error).
1109
Event notification: Fibre Channel driver encountered a fatal error.
1112
Event notification: Fibre Channel port logged out.
1282
Failed to allocate object for iSCSI session: out of session resources.
1292
Received iSCSI PDU with duplicate command sequence number (CmdSN).
Command PDU will be dropped.
1298
Unable to allocate iSCSI initiator object while instantiating session.
1444
Failed to execute iSCSI Command PDU because its CmdSN is out-of-range.
Log message contains the incorrect CmdSN, the valid CmdSN range, the first
byte of the CDB, and the data length.
1688
Event notification: iSCSI driver encountered a fatal error.
1689
Event notification: an IOCTL request was received to unload the iSCSI driver.
1694
Event notification: attempt to connect to the iSNS server failed.
2052
iSNS connection failed.
2053
Break up I/O DSD allocation failed.
2305
Break up I/O recover DSD allocation failed.
2307
Data buffer allocation failed (length %d) during tpb extension allocation.
2308
Allocation of DSD failed during Tpb extension allocation. Buffer length %d.
2309
FCIP incoming frame: BUGCHECK: Trb (0x%p) ValidFlag (0x%x) Direction
(0x%x).
2310
FCIP incoming frame: GetFcipMapPortal failed.
2311
FCIP incoming frame: Got Status aborted pTrb->pBufDescList[0]:%p Trb
Direction:0x%x.
2312
FCIP system error.
2313
FCIP system error: QLOP_IssuePortEnable failed.
FI0054601-00 C
A
FI0054601-00 C
B – Log Messages
Error Log Messages
2320
FCIP handle Teb: Driver Fatal error.
2321
FCIP configure portal: Find portal object failed for QLUT_TYPE_FC, PortId
(%d).
2322
FCIP configure portal: QLFCIP_ConfigPortal: Invalid PortId for FCIP link
PortID(%d).
2323
FCIP allocate TRB pool: Allocation failed (size 0x%x).
2324
FCIP Trb: Null portal object in map table.
2325
FCIP eet TRB: Null portal object in map table.
2326
FCIP get TRB: Duplicate allocation of FcipTrb (0x%p).
2327
FCIP free TRB: Null portal object in map table.
2328
FCIP free TRB: Duplicate Free of FcipTrb (0x%p).
2329
FCIP initialize buffer descriptor pool: memory allocation for
FCIP_BUF_EXT_DESC failed (size 0x%x).
2336
FCIP free data buffers: Duplicate Freeing of DataBuf (0x%p).
2337
FCIP allocate data buffers: Duplicate allocation of DataBuffer (0x%p).
2338
FCIP allocate data buffer: Got NULL PORTAL Object in map table MEM LEAK.
2339
FCIP de-allocate data buffer: Null portal object in map table.
2340
FCIP create data buffer pool: Allocation of 32K buffers from LargeBufferPool
failed.
2561
Break up I/O: TPB allocation failed.
2562
Break up I/O: Data buffer and TPB allocation failed.
B-17
S
B – Log Messages
Error Log Messages
iSCSI Driver
The following error log messages are common to both iSCSI ports, 1 (GE1) and 2
(GE2). They are listed in Table B-9 and described following the table. Log
messages beginning with #0 denote iSCSI port 1 (GE1). Log messages beginning
with #1 denote iSCSI port 2 (GE2).
Table B-9. iSCSI Driver—Error Log Messages
ID
B-18
Log Message
No.
73990
#%d: QLUtmIoctlEnable: Initialize FW failed
262
74046
#%d: QLPortUp: MBOX_CMD_SET_PORT_CONFIG %04x
failed %04x
318
74056
#%d: QLRunDiag: MBOX Diag test internal loopback
failed %x %x
328
74057
#%d: QLRunDiag: MBOX Diag test external loopback
failed %x %x
329
74065
#%d: QLPortDown: MBOX_CMD_SET_PORT_CONFIG %04x
failed %04x
337
74241
#%d: QLiSNSEnableCallback: iSNS Server TCP Connect failed
513
74577
#%d: QLIsrDecodeMailbox: NVRAM invalid
849
74587
#%d: QLIsrDecodeMailbox: Link down
859
74656
#%d: QLReadyTimer: Adapter missed heartbeat for %d seconds. Time left %d
928
74661
#%d: QLTimer: Abort pTpb=%p, Type %x, Timeout 0x%x DrvCount 0x%x, DdbIndex 0x%x
933
74663
#%d: QLReadyTimer: MBOX_CMD %04x %04x %04x %04x
%04x %04x %04x %04x timed out
935
74665
#%d: QLReadyTimer: QLiSNSReenable failed.
937
74784
#%d: QLUpdateInitiatorData: No more room in Initiator Database.
1056
74800
#%d: QLSetTargetData: No more room in Target Database.
1072
262
The iSCSI processor failed firmware initialization.
318
The iSCSI processor command to enable a GE port failed.
328
The iSCSI processor failed the internal loopback test.
FI0054601-00 C
A
FI0054601-00 C
B – Log Messages
Error Log Messages
329
The iSCSI processor failed the external loopback test.
337
The iSCSI processor command to disable a GE port failed.
513
The iSCSI processor could not connect with the iSCSI name server (iSNS).
849
The iSCSI processor reported that the iSCSI port NVRAM contains invalid
data (checksum error).
859
The iSCSI processor reported a link down condition.
928
The driver failed to receive a heartbeat from the iSCSI processor for the
specified number of seconds.
933
The driver timed out an iSCSI processor operation and is aborting the operation.
935
The driver timed out an iSCSI processor mailbox command.
937
The driver timed out while attempting to reconnect with the iSNS.
1056
The driver’s initiator database is full. The driver is capable of storing
1024 iSCSI initiators in its database. Use the CLI or SANsurfer Router Manager to remove unwanted/unused iSCSI initiators.
1072
The driver’s target database is full. Use the CLI or SANsurfer Router Manager to remove unwanted/unused iSCSI targets.
B-19
S
B – Log Messages
Error Log Messages
Fibre Channel Driver
The following error log messages are common to both Fibre Channel ports, 1
(FC1) and 2 (FC2). They are listed in Table B-10 and described in this section.
Log messages beginning with #0 denote fibre channel port 1 (FC1) and log
messages beginning with #1 denote fibre channel port 2 (FC2).
Table B-10. Fibre Channel Driver—Error Log Messages
B-20
ID
Log Messages
No.
106583
#%d: QLUtmReceiveIo: Path invalid/FW No resource count %x
87
106589
#%d: QLIoctlEnable: Adapter disabled
93
106590
#%d: QLIoctlEnable: Initialize FW error
94
106592
#%d: QLIoctlRunDiag: Diagnostic loopback command failed %x
% %x %x
96
106593
#%d: QLIoctlDisable: Re-initialize adapter failed
97
106595
#%d: QLUtmReceiveIo: Invalid VP Loop Id 0x%x
99
106803
#%d: QLIsrEventHandler: Link down (%x)
307
106813
#%d: QLIsrEventHandler: Unexpected async event (%x),
MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x,
MB7=%x
317
106846
#%d: QLProcessResponseQueueFS: TRB is NULL: %d
350
106853
#%d: QLTimer: Link error count (0x%x) exceeded, link down
357
106912
#%d: QLReserveLoopId: out of loop Ids
416
106928
#%d: QLMarkDeviceOffline: Device Id: %x marked offline,
cLinkDownTimeout = %x, cPortDownRetryCount=%x
432
106948
#%d: QLSnsGetAllNext: Name server login FAILED %x
452
107029
#%d: QLUpdateDeviceData: out of slots in host database
533
107030
#%d: QLUpdateDeviceData: out of slots in target database
534
107041
#%d: QLUpdateDeviceDatabase 0x%x: GET_ID failed %x
545
107056
#%d: QLUpdateDeviceDatabase 0x%x: out of slots in host
database
560
107058
#%d: QLUpdateDeviceDatabase 0x%x:
MBOX_CMD_GET_VP_DATABASE failed %x
562
107078
#%d: QLUpdatePort 0x%x: out of slots in host database
582
FI0054601-00 C
A
B – Log Messages
Error Log Messages
Table B-10. Fibre Channel Driver—Error Log Messages (Continued)
ID
FI0054601-00 C
Log Messages
No.
107254
#%d: QLUpdateSinglePortCont 0x%x: out of slots in host
database
758
107267
#%d: QLFcipIsrEventHandler: System error event (%x),
MB1=%x, MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x,
MB7=%x
771
87
The FC processor received a SCSI command for an unknown target path or
has run out of resources to execute additional commands.
93
The FC processor was disabled by an IOCTL request to the driver.
94
The FC processor firmware failed initialization. The request to initialize was
received by the driver in an IOCTL request.
96
The FC processor failed the external loopback test.
97
The FC processor failed to re-initialize in response to an IOCTL disable
request.
99
Invalid Virtual Port loop ID.
307
The FC processor reported a link down condition.
317
The FC processor reported an unexpected asynchronous event. The mailbox
registers provide status, event code, and data related to the event.
350
FCIP Response queue entry TRB pointer is NULL.
357
The driver has determined that the FC link is unreliable and unusable due to
the number of errors encountered. The link has been taken down.
416
The FC processor was unable to obtain the number of loop IDs required. This
failure occurs only when the FC processor is running multi-ID firmware.
432
The driver was unable to re-establish connection to the target within the
timeout and retry counts, and is therefore marking it offline.
452
The FC processor is unable to log into the FC fabric name server.
533
The driver’s host (initiator) database is full.
545
The driver’s target database is full.
560
The driver’s host (initiator) database is full. Maximum host database is 64.
562
FC processor "Get VP Database entry command" failed.
B-21
S
B – Log Messages
Error Log Messages
582
The drivers host (initiator) database is full.
758
No slots available in host database.
771
FCIP system error event.
User Modules
The user modules generate the error log messages listed in Table B-11 and
described following the table.
Table B-11. User Modules—Error Log Messages
ID
B-22
Log Message
No.
139265
QBRPC_Initialize: Entered
1
139266
QBRPC_Initialize:GetBridge Mem Allocation error
2
139267
QBRPC_Initialize:GetBridgeAdv Mem Allocation error
3
139268
QBRPC_Initialize:GetMgmt Mem Allocation error
4
139269
QBRPC_Initialize:GetIscsi Mem Allocation error
5
139270
QBRPC_Initialize:GetIscsiAdv Mem Allocation error
6
139271
QBRPC_Initialize:GetIsns Mem Allocation error
7
139272
QBRPC_Initialize:GetFcIntfc Mem Allocation error
8
139273
QBRPC_Initialize:GetFcAdv Mem Allocation error
9
139280
QBRPC_Initialize:GetFcSfp Mem Allocation error
16
139281
QBRPC_Initialize:GetLog Mem Allocation error
17
139282
QBRPC_Initialize:GetStats Mem Allocation error
18
139283
QBRPC_Initialize:InitListMem Allocation error
19
139284
QBRPC_Initialize:TargetList Mem Allocation error
20
139285
QBRPC_Initialize:LunList MemAllocation error
21
139286
QBRPC_Initialize:PresTarget Mem Allocation error
22
139287
QBRPC_Initialize:LunMask Mem Allocation error
23
139288
QBRPC_Initialize:Init Mem Allocation error
24
139289
QBRPC_Initialize:TgtDevice Mem Allocation error
25
139296
QBRPC_Initialize:FcTgt Mem Allocation error
32
FI0054601-00 C
A
B – Log Messages
Error Log Messages
Table B-11. User Modules—Error Log Messages (Continued)
ID
FI0054601-00 C
Log Message
No.
139297
QBRPC_Initialize:BridgeStatus Mem Allocation error
33
139298
QBRPC_Initialize:Diag Mem Allocation error
34
139299
QBRPC_Initialize:DiagLog Mem Allocation error
35
139300
QBRPC_Initialize:FruImage Mem Allocation error
36
139301
QBRPC_Initialize:OemMfg Mem Allocation error
37
139302
QBRPC_Initialize:Status Mem Allocation error
38
139303
QBRPC_Initialize:TcpIpStats Mem Allocation error
39
139304
QBRPC_Initialize:NtpStats Mem Allocation error
40
139305
QBRPC_Initialize:LunList MemAlloc error
41
139315
QBRPC_FreeResources:Entered
51
139553
checkDuplicateIp: Detected Error %08x %08x%04x
289
1
RPC (remote procedure call) server initialization entry point.
2
Get System API memory allocation failed.
3
Get System Advanced API memory allocation failed.
4
Get Management API memory allocation failed.
5
Get iSCSI API memory allocation failed.
6
Get iSCSI advanced API memory allocation failed.
7
Get iSNS API memory allocation failed.
8
Get FC Interface API memory allocation failed.
9
Get FC Advanced API memory allocation failed.
16
Failed memory allocation for Get FC SFP API.
17
Failed memory allocation for Get Log API.
18
Failed memory allocation for Get Statistics API.
19
Failed memory allocation for Get Initiator List API.
20
Failed memory allocation for Get Target List API.
B-23
S
B – Log Messages
Error Log Messages
B-24
21
Failed memory allocation for Get LUN List API.
22
Failed memory allocation for Get Presented Targets List API.
23
Failed memory allocation for Get LUN Mask API.
24
Failed memory allocation for Initiator API.
25
Failed memory allocation for Target Device API.
32
Failed memory allocation for FC Target API.
33
Failed memory allocation for System Status API.
34
Failed memory allocation for Diagnostic API.
35
Failed memory allocation for Diagnostic Log API.
36
Failed memory allocation for FRU Image API.
37
Failed memory allocation for OEM Manufacturing API.
38
Failed memory allocation for Status API.
39
Failed memory allocation for TCP/IP Statistics API.
40
Failed memory allocation for NTP Status API.
41
Failed memory allocation for LUN List API.
51
RPC free resources entry point.
289
Detected duplicate IP address for management port.
FI0054601-00 C
A
B – Log Messages
Fatal Log Messages
System
The system modules generate the error log messages listed in Table B-12 and
described following the table.
Table B-12. System—Error Log Messages
ID
Log Message
No.
237572
"Failed to kill sys killer %d\n"
4
237573
"Temperature over high threshold %d\n"
5
4
Failed to kill system task.
5
Reporting router exceeds maximum operating temperature.
Fatal Log Messages
The following sections list and describe the fatal log messages by reporting
module.
iSCSI Driver
The following fatal log messages are common to both iSCSI ports, 1 (GE1) and 2
(GE2). They are listed in Table B-13 and described following the table. Log
messages beginning with #0 denote iSCSI port 1 (GE1). Log messages beginning
with #1 denote iSCSI port 2 (GE2).
Table B-13. iSCSI Driver—Fatal Log Messages
ID
FI0054601-00 C
Log Message
No.
69652
#%d: qlutm_init: Diagnostic failed, invalid SRAM
20
69653
#%d: qlutm_init: Diagnostic failed, fail reboot
21
69654
#%d: qlutm_init: Diagnostic failed, invalid NVRAM
22
69655
#%d: qlutm_init: Diagnostic failed, invalid DRAM
23
69656
#%d: qlutm_init: Failed to return diagnostic result to Bridge
24
69941
#%d: QLUtmProcessResponseQueue: Invalid handle %x
EntryType %x
309
69951
#%d: QLSetNvram: QLRebootTimer failed AF %x RS %x
Time %d
319
B-25
S
B – Log Messages
Fatal Log Messages
Table B-13. iSCSI Driver—Fatal Log Messages (Continued)
B-26
ID
Log Message
No.
69964
#%d: QLDisable: QLRebootTimer failed AF %x RS %x Time %d
332
69966
#%d: QLEnable: QLRebootTimer failed AF %x RS %x Time %d
334
70224
#%d: QLProcSrblessiSNSResponse: Invalid handle %x
592
70400
#%d: QLInitializeDevice: QLStartAdapter failed
768
70417
#%d: QLInitializeAdapter: QLInitializeFW failed
785
70432
#%d: QLDoInterruptServiceRoutine: PortFatal interrupt.
PortFatalErrorStatus %08x CSR %08x AS %x AF %x
800
70448
#%d: QLStartAdapter: QLRebootTimer failed AF %x RS %x
Time %d
816
70489
#%d: QLIsrDecodeMailbox: System Error 8002 MB[1-7] %04x
%04x %04x %04x %04x %04x %04x
857
70499
#%d: QLProcessResponseQueue: Invalid handle for
ET_PASSTHROUGH_STATUS
867
70501
#%d: QLProcessResponseQueue: Invalid entry type in response
queue %x
869
70502
#%d: QLProcessResponseQueue: Invalid handle %x
EntryType %x
870
70524
#%d: QLProcessAen: Invalid event %x
892
70544
#%d: QLRebootTimer: Reboot failed!
912
70563
#%d: QLReadyTimer: Adapter missed heartbeat for 0x%x
seconds. Rebooting
931
70564
#%d: QLReadyTimer: Abort pTpb=%p failed, DrvCount 0x%x
932
70609
#%d: QLProcessSystemError: Restart RISC
977
70610
#%d: QLProcessSystemError: RebootHba failed
978
70784
#%d: QLConfigChip: invalid NVRAM
1152
70835
#%d: QLStartFw: MBOX_CMD_SET_FLASH failed %x
1203
70836
#%d: QLStartFw: Invalid Fw loader state 0x%x
1204
70837
#%d: QLStartFw: Load Fw loader timeout
1205
FI0054601-00 C
A
FI0054601-00 C
B – Log Messages
Fatal Log Messages
20
iSCSI processor SRAM test failed.
21
iSCSI processor failed diagnostic reboot.
22
iSCSI processor failed NVRAM diagnostic.
23
iSCSI processor failed DRAM diagnostic.
24
iSCSI processor failed to return diagnostic results.
309
Response queue entry contains an invalid handle.
319
Set NVRAM reboot timer failed.
332
Port disable reboot timer failed.
334
Port enable reboot timer failed.
592
iSNS response contains an invalid handle.
768
Start iSCSI processor failed.
785
iSCSI processor firmware initialization failed.
800
iSCSI processor port fatal error.
816
Start iSCSI processor reboot timer failed.
857
iSCSI processor fatal system error.
867
Response queue invalid handle for ET pass-through.
869
Response queue invalid entry type.
870
Response queue invalid handle for specified entry type.
892
Asynchronous event for unknown event type.
912
Reboot timer failed.
931
iSCSI driver missed iSCSI processor heartbeat. iSCSI processor rebooted.
932
iSCSI processor failed to complete operation before timeout.
977
iSCSI processor system error restart.
978
iSCSI processor reboot failed.
1152
iSCSI processor NVRAM invalid (checksum error).
1203
iSCSI FLASH (NVRAM) command failed.
1204
iSCSI firmware loader invalid state.
1205
iSCSI failed to load firmware in time allotted.
B-27
S
B – Log Messages
Fatal Log Messages
FC Driver
The following fatal log messages are common to both Fibre Channel ports, 1
(FC1) and 2 (FC2). They are listed in Table B-14 and described following the
table. Log messages beginning with #0 denote fibre channel port 1 (FC1). Log
messages beginning with #1 denote fibre channel port 2 (FC2).
Table B-14. Fibre Channel Driver—Fatal Log Messages
ID
B-28
Log Message
No.
102419
#%d: qlutm_init: Diagnostic failed, port 1 invalid SRAM
19
102420
#%d: qlutm_init: Diagnostic failed, port 1 POST failed
20
102421
#%d: qlutm_init: Diagnostic failed, port 2 invalid SRAM
21
102422
#%d: qlutm_init: Diagnostic failed, port 2 POST failed
22
102423
#%d: qlutm_init: Failed to return diagnostic result to Bridge
23
102656
#%d: QLInitializeAdapter: Reset ISP failed
256
102657
#%d: QLInitializeAdapter: Load RISC code failed
257
102658
#%d: QLInitializeAdapter: Load ISP2322 receive sequencer code
failed
258
102659
#%d: QLInitializeAdapter: Load ISP2322 transmit sequencer
code failed
259
102662
#%d: QLInitializeAdapter: Verify Checksum command failed (%x)
262
102680
#%d: QLInitializeFW: FAILED
280
102688
#%d: QLInterruptServiceRoutine: Risc pause %x with parity error
hccr %x, Disable adapter
288
102689
#%d: QLInterruptServiceRoutine: Invalid interrupt status: %x
289
10691
#%d: QLFcipInterruptServiceRoutine: Risc pause %x with parity
error hccr %x, Disable adapter
291
10692
#%d: QLFcipInterruptServiceRoutine: Invalid interrupt status: %x
292
102716
#%d: QLIsrEventHandler: System error event (%x), MB1=%x,
MB2=%x, MB3=%x, MB4=%x, MB5=%x, MB6=%x, MB7=%x
316
102746
#%d: QLProcessResponseQueue: Invalid handle %x, type %x
346
102747
#%d: QLProcessResponseQueueFS: Invalid buffer type: %x
347
102748
#%d: QLProcessResponseQueueFS: Invalid EntryType (0x%x)
348
FI0054601-00 C
A
B – Log Messages
Fatal Log Messages
Table B-14. Fibre Channel Driver—Fatal Log Messages (Continued)
FI0054601-00 C
ID
Log Message
No.
102749
#%d: QLProcessResponseQueueFS: Invalid handle 0x%x, type
0x%x
349
102752
#%d: QLTimer: Ext Ram parity error exceed limit cnt 0x%x, limit
0x%x, Disabled adapter
352
102755
#%d: QLTimer: Heartbeat failed
355
102800
#%d: QLRestartRisc: restart RISC
400
19
FC1 processor SRAM test failed.
20
FC1 processor power-on self-test (POST) failed.
21
FC2 processor SRAM test failed.
22
FC2 processor POST failed.
23
FC processor failed to return diagnostic results.
256
FC processor failed reset.
257
FC processor firmware load failed.
258
FC processor receive sequencer code load failed.
259
FC processor transmit sequencer code load failed.
262
FC processor firmware checksum failed.
280
FC processor firmware initialization failed.
288
FC processor paused due to internal parity error.
289
FC processor returned an invalid interrupt status.
291
FC processor invalid interrupt status.
292
FC processor paused due to RAM parity error.
316
FC processor system error.
346
Response queue entry contains an invalid handle.
347
FCIP: Response queue entry contains an invalid buffer type.
348
FCIP: Response queue entry contains an invalid entry type.
349
FCIP: Response queue entry contains an invalid handle.
B-29
S
B – Log Messages
Fatal Log Messages
352
FC processor external SRAM parity error count exceeded limit: FC port
disabled.
355
FC processor heartbeat failed.
400
FC processor being restarted.
TOE Driver
The TOE driver generates the fatal log messages listed in Table B-15 and
described following the table.
Table B-15. TOE—Fatal Log Messages
ID
B-30
Log Message
No.
200721
QL3022:ql3xxx_probe: Adapter eth#%d, Invalid NVRAM
parameters
17
200725
QL3022:eth%x: Resetting chip. PortFatalErrStatus register =
0x%x
21
17
Encountered invalid parameters in TOE NVRAM.
21
TOE chip reset due to detection of fatal error.
FI0054601-00 C
A
B – Log Messages
Fatal Log Messages
System
The system modules generate the fatal log messages listed in Table B-16 and
described following the table.
Table B-16. System—Fatal Log Messages
FI0054601-00 C
ID
Log Message
No.
233473
"memory monitor: Detected Uncorrectable Ecc %08lx system is
rebooting in 5 secs\n"
1
233474
"Failed to register interrupt handler!\n"
2
233475
"%s class_simple_create failed\n"
3
1
Uncorrectable memory error detected at address provided in log message.
2
Attempt to register the interrupt handler failed.
3
Failed class_simple_create system call from memory monitor initialization
routine.
B-31
B – Log Messages
Fatal Log Messages
S
Notes
B-32
FI0054601-00 C
C
Configuring CHAP
CHAP Definition
In challenge handshake authentication protocol (CHAP), the authentication agent
sends the client program a random value that is used only once and an ID value.
Both the sender and peer share a predefined secret. The peer concatenates the
random value, the ID, and the secret, and calculates a one-way hash using MD5
(Message-Digest algorithm 5). It sends the hash value to the authenticator, which
in turn builds that same string on its side, calculates the MD5 checksum, and
compares the result with the value received from the peer. If the values match, the
peer is authenticated.
By transmitting only the hash, the secret cannot be reverse-engineered. The ID
value is increased with each CHAP dialogue to protect against replay attacks.
Configuring CHAP Using CLI
The following sections describe the procedure for configuring CHAP from the
command line interface (CLI).
CLI—Discovery Session—Bi-directional CHAP
To configure a bi-directional CHAP used during a discovery session:
1.
2.
3.
FI0054601-00 C
On the router:
a.
Enable CHAP on the port.
b.
Create a secret (for example, secret_port).
c.
Using Set Chap, choose the iSCSI node that represented the GE port.
d.
Use Show Iscsi to find the iSCSI node name of the GE port.
Use Initiator add to add the initiator that is about to do discovery:
a.
Enable the CHAP for this initiator.
b.
Create a secret (for example, secret_initiator).
c.
Use Set Chap to update the CHAP settings of the initiator.
Go to the Microsoft iSCSI (MS) Initiator and perform the following steps:
C-1
S
C – Configuring CHAP
Configuring CHAP Using CLI
a.
Click General.
b.
Click Secret (in the middle of the screen). If this is the first time you are
setting secrets, reset all secrets.
c.
Type the secret (secret_port) that you created in Step 1.
4.
Click Discovery.
5.
Click Add.
6.
Type the address of the iSCSI port of the router.
7.
Click Advanced.
8.
Select Chap Login Information.
9.
Type the secret (secret_initiator) you created in Step 2 into Target Secret.
10.
Select Mutual Authentication.
11.
Click OK.
12.
Click OK. The initiator completes the discovery.
CLI—Discovery Session—Uni-directional CHAP
To configure a single-direction CHAP used during a discovery session:
C-2
1.
Do not enable CHAP on the ISCSI port.
2.
Use Initiator add:
a.
Add the initiator that is about to perform the discovery.
b.
Enable the CHAP for this initiator.
c.
Create a secret (for example, secret_initiator).
d.
Use Set Chap to update the initiator’s CHAP settings.
3.
Go to the MS Initiator.
4.
Click Discovery.
5.
Click Add.
6.
Type the address of the iSCSI port of the router.
7.
Click Advanced.
8.
Select Chap Login Information.
9.
In Target Secret, type the secret (secret_initiator) you created in Step 2.
10.
Click OK.
11.
Click OK. The initiator should complete discovery.
FI0054601-00 C
A
C – Configuring CHAP
Configuring CHAP Using CLI
CLI—Normal Session—Bi-directional CHAP
To configure a bi-directional CHAP used during a normal session:
1.
2.
3.
On the router
a.
Enable CHAP on the presented target to which the initiator will login.
b.
Create a secret (for example, secret_target).
c.
Use Set CHAP.
Use Initiator add to add the initiator that is about to do a normal login:
a.
Enable the CHAP for this initiator.
b.
Create a secret (for example, secret_initiator).
c.
Use Set Chap to update the CHAP settings of the initiator.
Go to the MS Initiator and perform the following steps:
a.
Click General.
b.
Click Secret (in the middle of the screen).
c.
If this is the first time you are setting secrets, reset all the secrets.
d.
Type the secret (secret_target) that you created in Step 1.
4.
Click Targets.
5.
Select the target you want to login to.
6.
Click Advanced.
7.
Select Chap Login Information.
8.
Type the secret (secret_initiator) that you created in Step 2 into Target
Secret.
9.
Select Mutual Authentication.
10.
Click OK.
11.
Click OK. The initiator completes the normal login.
FI0054601-00 C
C-3
S
C – Configuring CHAP
Configuring CHAP Using the GUI
CLI—Normal Session—Uni-directional CHAP
To configure single-direction CHAP to be used during a normal session:
1.
Do not enable CHAP on the presented target.
2.
Use Initiator add:
a.
Add the initiator that is about to do a normal login.
b.
Enable the CHAP for this initiator.
c.
Create a secret (for example, secret_initiator).
d.
Use Set Chap to update the CHAP settings of the initiator.
3.
Go to the MS Initiator.
4.
Click Targets.
5.
Select the target you want to login to.
6.
Click Advanced.
7.
Select Chap Login Information.
8.
Type the secret (secret_initiator) that you created in into Target Secret.
9.
Click OK.
10.
Click OK. The initiator completes the normal login.
Configuring CHAP Using the GUI
The following sections describe the procedure for configuring CHAP using the
SANsurfer Router Manager, the graphical user interface (GUI).
GUI—Discovery Session—Bi-directional CHAP
To configure a bi-directional CHAP during a discovery session:
1.
On the bridge, enable CHAP for the iSCSI port.
2.
Select the port in the left column.
3.
Click Advanced Configuration.
4.
Select Enable Chap.
5.
Type a secret in Chap secret (for example, secret_port).
6.
Check to see if the initiator exists on the discovered iSCSI initiators list:
7.
C-4
„
If the initiator is not part of the discovered iSCSI initiators list, then go
to the wizard menu and select Add Initiator Wizard.
„
If the initiator is part of the discovered list, then go to Step 10.
Type the IQN name string.
FI0054601-00 C
A
C – Configuring CHAP
Configuring CHAP Using the GUI
8.
Select Enable CHAP.
9.
Create a CHAP secret (for example, secret_initiator).
10.
Go to the MS Initiator and perform the following steps:
a.
Click General.
b.
Click Secret (in the middle of the screen).
c.
If this is the first time you are setting secrets, reset all secrets.
d.
Type the CHAP secret (secret_port) that you created in Step 5.
11.
Click Discovery.
12.
Click Add.
13.
Enter the address of the iSCSI port of the bridge.
14.
Click Advanced.
15.
Select Chap Login Information.
16.
Type the secret (secret_initiator) that you created in Step 9 into Target
Secret.
17.
Select Mutual Authentication.
18.
Click OK.
19.
Click OK. The initiator completes discovery.
GUI—Discovery Session—Uni-directional CHAP
To program a single-direction CHAP during a discovery session:
1.
Do not enable CHAP on the iSCSI port.
2.
Check to see if the initiator exists on the discovered iSCSI initiators list:
„
If the initiator is not part of the discovered iSCSI initiators list, then go
to the wizard menu and select Add Initiator Wizard.
„
If the initiator is part of the discovered list, then go to Step 6.
3.
Type the IQN name string.
4.
Select Enable Chap.
5.
Create a CHAP secret (for example, secret_initiator).
6.
Go to the MS Initiator and perform the following steps:
FI0054601-00 C
a.
Click Discovery.
b.
Click Add.
c.
Enter the address of the iSCSI port of the bridge.
C-5
S
C – Configuring CHAP
Configuring CHAP Using the GUI
d.
Click Advanced.
e.
Click Chap Login Information.
f.
Type the secret (secret_initiator) you created in Step 5 into Target
Secret.
7.
Click OK.
8.
Click OK. The initiator completes discovery.
GUI—Normal Session—Bi-directional CHAP
To program bi-directional CHAP during a normal session:
C-6
1.
On the bridge, enable CHAP for the iSCSI presented target.
2.
Select the presented target on the left column of the SANsurfer Router
Manager.
3.
Click Information.
4.
Select Enable Chap.
5.
Type a secret in the Chap secret dialog box (for example, secret_target).
6.
Check to see if the initiator exists on the discovered iSCSI initiators list:
„
If the initiator is not part of the discovered iSCSI initiators list, then go
to the wizard menu and select Add Initiator Wizard.
„
If the initiator is part of the discovered list, then go to Step 10.
7.
Fill in the IQN name string.
8.
Select Enable Chap.
9.
Create a CHAP secret (for example, secret_initiator).
10.
Go to the MS Initiator and perform the following steps:
a.
Click General.
b.
Click Secret (in the middle of the screen).
c.
If this is the first time you are setting secrets, reset all the secrets.
d.
Type the secret (secret_target) that you created in Step 5.
11.
Click Targets.
12.
Select the target you want to login to.
13.
Click Log On.
14.
Click Advanced.
15.
Select Chap Login Information.
FI0054601-00 C
A
C – Configuring CHAP
Configuring CHAP Using the GUI
16.
Type the secret (secret_initiator) that you created in Step 9 into Target
Secret.
17.
Select Mutual Authentication.
18.
Click OK.
19.
Click OK. The initiator completes normal login.
GUI—Normal Session—Uni-directional CHAP
To program single-direction CHAP during a normal session:
1.
Do not enable CHAP on the iSCSI presented target.
2.
Check to see if the initiator exists on the discovered iSCSI initiators list:
„
If the initiator is not part of the discovered iSCSI initiators list, then go
to the wizard menu and select Add Initiator Wizard.
„
If the initiator is part of the discovered list, then go too Step 6.
3.
Fill in the IQN name string.
4.
Select Enable Chap.
5.
Create a CHAP secret (for example, secret_initiator).
6.
Go to the MS Initiator and perform the following steps:
7.
FI0054601-00 C
a.
Click Targets.
b.
Select the target you want to login to.
c.
Click Log On.
d.
Click Advanced.
e.
Click Chap Login Information.
f.
Type the secret (secret_initiator) you created in Step 5 into Target
Secret,
g.
Click OK.
Click OK. The initiator completes normal login.
C-7
C – Configuring CHAP
Configuring CHAP Using the GUI
S
Notes
C-8
FI0054601-00 C
D
Simple Network
Management Protocol
(SNMP)
Introduction
Simple network management protocol (SNMP) provides monitoring and trap
functions for managing the router through third-party applications that support
SNMP. The router firmware supports SNMP versions 1 and 2 and a QLogic
Management Information Base (MIB). You may format the traps using SNMP
version 1 or 2 (See Notifications).
SNMP Properties
You can set the SNMP properties using either the command line interface (see
Set SNMP Command) or the SANsurfer Router Manager.
Table D-1 describes the SNMP properties.
Table D-1. SNMP Properties
Parameter
FI0054601-00 C
Description
Read community
A password that authorizes an SNMP management server to
read information from the router. This is a write-only field. The
value on the router and the SNMP management server must
be the same. The read community password can be up to
32 characters excluding the number sign (#), semicolon (;), and
comma (,). The default is password is public.
Trap community
A password that authorizes an SNMP management server to
receive traps. This is a write-only field. The value on the router
and the SNMP management server must be the same. The
trap community password can be up to 32 characters excluding
the number sign (#), semicolon (;), and comma (,). The default
password is public.
System location
Specifies the name of the router location. The name can be up
to 64 characters excluding the number sign (#), semicolon (;),
and comma (,). The default is undefined.
D-1
S
D – Simple Network Management Protocol (SNMP)
Introduction
Table D-1. SNMP Properties (Continued)
Parameter
Description
System contact
Specifies the name of the person to be contacted to respond to
trap events. The name can be up to 64 characters excluding
the number sign (#), semicolon (;), and comma (,). The default
is undefined.
Authentication traps
Enables or disables authentication trap generation in response
to authentication failures. The default is disabled.
SNMP Trap Configuration
SNMP trap configuration supports setting up to eight trap destinations. Choose
from Traps 1–Trap 8 to configure each trap. Table D-2 describes the parameters
for configuring a SNMP trap.
Table D-2. SNMP Trap Configuration Parameters
Parameter
Description
Trap n enabled
Enables or disables trap n. If disabled, the trap is not configured.
Trap address*
Specifies the IP address to which the SNMP traps are sent. A maximum of eight trap addresses are supported. The default address
for traps is 0.0.0.0.
Trap port*
The port number on which the trap is sent. The default is 162.
Trap version
Specifies the SNMP version (1 or 2) with which to format traps.
Table Notes
*
Trap address (other than 0.0.0.) and trap port combinations must be unique. For example, if trap 1 and trap 2
have the same address, then they must have different port values. Similarly, if trap 1 and trap 2 have the same
port value, they must have different addresses.
D-2
FI0054601-00 C
A
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
Management Information Base (MIB)
The following sections describe the QLogic management information base (MIB).
The MIB consists of four object groups:
„
System Information
„
Network Port Table
„
Fibre Channel Port Table
„
Fibre Channel Port Table
System Information
The system information objects provide the system serial number, version
numbers (hardware/software/agent), and number of ports (FC/GE).
qsrSerialNumber
Syntax SnmpAdminString
Access Read only
Description The system serial number.
qsrHwVersion
Syntax SnmpAdminString
Access Read only
Description The system hardware version number.
qsrSwVersion
Syntax SnmpAdminString
Access Read only
Description The system software (firmware) version
number.
qsrNoOfFcPorts
Syntax Unsigned32
Access Read only
Description The number of Fibre Channel ports on the
system.
FI0054601-00 C
D-3
S
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
qsrNoOfGbEPorts
Syntax Unsigned32
Access Read-only
Description The number of gigabit Ethernet ports on
the system.
qsrAgentVersion
Syntax SnmpAdminString
Access Read only
Description The version number of the agent software
on the system.
Network Port Table
The network port table contains a list of network ports that are operational on the
router. The entries in this table include the management port, the iSCSI ports, and
the TOE ports on the router. A single gigabit Ethernet port can function as an
iSCSI port and a TOE simultaneously; therefore, there may be up to two entries
for a given gigabit Ethernet port.
qsrNwPortTable
Syntax Sequence of QsrNwPortEntry
Access Not accessible
Description The entries in this table include the
management port, and the iSCSI, and TOE
ports on the router.
qsrNwPortEntry
Syntax QsrNwPortEntry
Access Not accessible
Description Each entry (row) contains information
about a specific network port.
QsrNwPortEntry
A network port entry consists of the following sequence of objects:
D-4
qsrNwPortRole
QsrPortRole
qsrNwPortIndex
unsigned32
qsrNwPortAddressMode
INTEGER
qsrIPAddressType
InetAddressType
qsrIPAddress
InetAddress
FI0054601-00 C
A
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
qsrNetMask
InetAddress
qsrGateway
InetAddress
qsrMacAddress
MacAddress
qsrNwLinkStatus
QsrLinkStatus
qsrNwLinkRate
QsrLinkRate
qsrNwPortRole
Syntax QsrPortRole
Access Not accessible
Description The operational role of this port:
management port, iSCSI port, a TOE.
qsrNwPortIndex
Syntax Unsigned32
Access Not accessible
Description A positive integer indexing each network
port in a given role.
qsrNwPortAddressMode
Syntax INTEGER
1 = Static
2 = DHCP
3 = Bootp
4 = RARP
Access Read only
Description The method by which the port gets its IP
address.
qsrIPAddressType
Syntax InetAddressType
Access Read only
Description The IP address type: ipv4 or ipv6.
qsrIPAddress
Syntax InetAddress
Access Read only
Description The IP address of the port.
FI0054601-00 C
D-5
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
S
qsrNetMask
Syntax InetAddress
Access Read only
Description The subnet mask for this port.
qsrGateway
Syntax InetAddress
Access Read only
Description The gateway for this port.
qsrMacAddress
Syntax IMacAddress
Access Read only
Description The MAC address for this port.
qstNwLinkStatus
Syntax QsrLinkStatus
Access Read only
Description The operational link status for this port.
qsrNwLinkRate
Syntax QsrLinkRate
Access Read only
Description The operational link rate for this port.
Fibre Channel Port Table
This table contains a list of the Fibre Channel (FC) ports on the router.There are
as many entries in this table as there are FC ports on the router.
qsrFcPortTable
Syntax Sequence of QsrFcPortEntry
Access Not accessible
Description A list of the FC ports on the router.There
are as many entries in this table as there
are FC ports on the router.
D-6
FI0054601-00 C
A
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
qsrFcPortEntry
Syntax QsrFcPortEntry
Access Not accessible
Description Each entry (row) contains information
about a specific FC port.
QsrFcPortEntry
A fibre channel port entry consists of the following sequence of objects:
qsrFcPortRole
QsrPortRole
qsrFcPortIndex
Unsigned32
qsrFcPortNodeWwn
PhysAddress
qsrFcPortWwn
PhysAddress
qsrFcPortId
PhysAddress
qsrFcPortType
Unsigned32
qsrFcLinkStatus
QsrLinkStatus
qsrFcLinkRate
QsrLinkRate
qsrFcPortRole
Syntax QsrPortRole
Access Not accessible
Description The operational role of this port: FCP mode
or frame shuttle mode.
qsrFcPortIndex
Syntax Unsigned32
Access Not accessible
Description A positive integer indexing each FC port in
a given role.
qsrFcPortNodeWwn
Syntax PhysAddress
Access Read only
Description The world wide name of the node that
contains this port.
FI0054601-00 C
D-7
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
S
qsrFcPortWwn
Syntax PhysAddress
Access Read only
Description The world wide name for this port.
qsrFcPortId
Syntax PhysAddress
Access Read only
Description The interface's 24-bit FC address identifier.
qsrFcPortType
Syntax Unsigned32
Access Read only
Description The type of FC port, as indicated by the use
of the appropriate value assigned by IANA.
The IANA-maintained registry for FC port
types can be found at:
www.iana.org/assignments/fc-port-types
qsrFcLinkStatus
Syntax QsrLinkStatus
Access Read only
Description The current link status for this port.
qsrFcLinkRate
Syntax QsrLinkRate
Access Read only
Description The current link rate for this port.
Sensor Table
This table contains a list of all the sensors on the router. There are as many
entries (rows) in this table as there are sensors.
qsrSensorTable
Syntax Sequence of QsrSensorEntry
Access Not accessible
Description A list of all the sensors on the router. There
are as many entries (rows) in this table as
there are sensors.
D-8
FI0054601-00 C
A
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
qsrSensorEntry
Syntax QsrSensorEntry
Access Not accessible
Description Each entry (row) corresponds to a single
sensor.
QsrSensorEntry
A sensor entry consists of the following sequence of objects:
qsrSensorType
INTEGER
qsrSensorIndex
Unsigned32
qsrSensorUnits
INTEGER
qsrSensorValue
Integer32
qsrUpperThreshold
Integer32
qsrLowerThreshold
Integer32
qsrSensorState
INTEGER
qsrSensorType
Syntax INTEGER
Temperature = 1
Access Not accessible
Description The type of data being measured by this
sensor.
qsrSensorIndex
Syntax Unsigned32
Access Not accessible
Description A positive integer identifying each sensor
of a given type.
qsrSensorUnits
Syntax INTEGER
Celsius = 1
Access Read only
Description The unit of measurement for the
sensor.
FI0054601-00 C
D-9
D – Simple Network Management Protocol (SNMP)
Management Information Base (MIB)
S
qsrSensorValue
Syntax Integer32
Access Read only
Description The current value of the sensor.
qsrUpperThreshold
Syntax Integer32
Access Read only
Description The upper-level threshold for this sensor.
qsrLowerThreshold
Syntax Integer32
Access Read only
Description The lower-level threshold for this
sensor.
qsrSensorState
Syntax INTEGER
Access Read only
Description The state of this sensor, indicating the
health of the system.
„ Unknown – The sensor value/thresholds cannot be determined.
D-10
„
Normal – The sensor value is within
normal operational limits.
„
Warning – The sensor value is
approaching a threshold.
„
Critical – The sensor value has
crossed a threshold.
FI0054601-00 C
A
D – Simple Network Management Protocol (SNMP)
Notifications
Notifications
The router provides the following notification types:
„
Notification Objects
„
Agent Start Up Notification
„
Agent Shut Down Notification
„
Network Port Down Notification
„
Fibre Channel Port Down Notification
„
Sensor Notification
„
Generic Notification
The following sections describe these notifications and objects they use.
Notification Objects
This section defines the objects used in notifications.
qsrEventSeverity
Syntax INTEGER
Access Accessible for notify
Description This notification indicates the severity of
the event. The value clear specifies that a
condition that caused an earlier trap is no
longer present.
qsrEventDescription
Syntax SnmpAdminString
Access Accessible for notify
Description A textual description of the event that
occurred.
qsrEventTimeStamp
Syntax DateAndTime
Access Accessible for notify
Description This notification indicates when the event
occurred.
Agent Start Up Notification
The agent startup notification indicates that the agent on the router has started
running.
FI0054601-00 C
D-11
D – Simple Network Management Protocol (SNMP)
Notifications
S
qsrAgentStartup uses the following object:
„
qsrEventTimeStamp
Agent Shut Down Notification
The agent shut down notification indicates that the agent on the router is shutting
down.
qsrAgentShutdown uses the following object:
„
qsrEventTimeStamp
Network Port Down Notification
The network port down notification indicates that the specified network port is
down. The next time the port comes up, this event is sent with the
qsrEventSeverity object set to clear.
qsrNwPortDown uses the following objects:
„
qsrNwLinkStatus
„
qsrEventTimeStamp
„
qsrEventSeverity
Fibre Channel Port Down Notification
The Fibre Channel port down notification indicates that the specified Fibre
Channel port is down. The next time the port comes up, this event is sent with the
qsrEventSeverity object set to clear.
qsrFcPortDown uses the following objects:
„
qsrFcLinkStatus
„
qsrEventTimeStamp
„
qsrEventSeverity
Sensor Notification
The sensor notification indicates that the state for the specified sensor is not
normal. When the sensor returns to the normal state, this event is sent with the
qsrEventSeverity object set to clear.
qsrSensorNotification uses the following objects:
D-12
„
qsrSensorValue
„
qsrSensorState
„
qsrEventTimeStamp
„
qsrEventSeverity
FI0054601-00 C
A
D – Simple Network Management Protocol (SNMP)
Notifications
Generic Notification
The generic notification reports events other than the defined event types. It
provides a description object that identifies the event in clear text.
qsrGenericEvent uses the following objects:
„
qsrEventTimeStamp
„
qsrEventSeverity
„
qsrEventDescription
FI0054601-00 C
D-13
D – Simple Network Management Protocol (SNMP)
Notifications
S
Notes
D-14
FI0054601-00 C