Download 2007 - Product Guide

Contents
Competitive Comparisons
Mixer Amps
Mixers
Amplifiers
Zone Paging Systems
CD Players and Tuners
Equalizers
Crossover
Compressor-Limiter
Contractor Tools
Headphone amp
Phantom Power Supply
Mic Spliiter
Line Splitter
Pro to consumer level matching
Pages 3-4
Pages 5-11
Pages 12-15
Pages 16-19
Pages 20-23
Page 24
Page 25
Page 26
Pages 26
Pages 27-28
Direct box
Mic Pre-amp
Hum eliminator
Speaker-to-line level matching
Distribution amp
Monitor panel
AV Essentials - microphones
Pages 29-30
Join the Aussie Team
Australian Monitor is a world wide firmly established brand that has avid U.S. supporters from
its initial introduction here. Starin is ready to help you make this a staple in your product mix.
Australian Monitor products are built well with an excellent price/performance value. Compare
to other products you may already know. Just try it and you will make the switch.
From larger, leading contractors like Esco Communications with four offices across their
state...to smaller operations...the value and reliability of Australian monitor has grown camps of
supporters. See for yourself by trying it why they are so convinced of its effectiveness.
“I have been using the Australian
Monitor products this past year and
am very pleased to hear that Starin
will be handling distribution. We
have had very good success with
this product line and I look forward
to continuing to use it.”
-Chip Roth Esco Communications
-Mark Fritz Esco Communications
“This is fantastic news Starin taking over, since I love this product
line. Please get me all materials, catalogs, dealer apps etc. I’ve
used this all the time and it’s a great product. Wonderful news for
Starin and us!”
-Don Lanier Pearl Productions
Competitive Comparisons
120w Mixer/Amplifier Comparison
Australian Monitor AMIS120
Australian Monitor AMIS120XL
TOA A-512A
4 mic/line
8 mic/line
2 mic, 2 mic/line, 2 line
Inputs
Yes, via Ch 2
Yes, via Ch 2
No
Telephone Input
18v DC (all mic inputs)
18v DC (all mic inputs)
15v DC (inputs 1&2)
Phantom Power
Master Bass & Treble
Master Bass, Mid & Treble
Master Bass & Treble
Equalisation
Yes (VOX), inputs 1&2 mute 3&4
Yes (VOX), multi-stage
Yes (Switch), mutes inputs 3-5
Priority
120w
120w
120w
Output Power
4Ω, 8Ω, 25v, 70v
4Ω, 8Ω, 25v, 70v
4Ω, 25v, 70v
Outputs
Yes, 6 zones
No
No
Speaker Zone Selection
Yes
Yes
No
Remote Master Volume
Yes,
4
tones
Yes,
4
tones
No
Tone Generator
Yes
Yes
Yes
Insert Point
Yes
Yes
Yes
Mix and Tape Output
Yes
Yes
No
Rack Kit Included
2RU
2RU
2RU
Rack Space
Yes
Yes
Yes
Mains and DC Power
$535.00
$660.00
$762.00
List Price
Inputs
Telephone Input
Phantom Power
Equalisation
Priority
Output Power
Outputs
Speaker Zone Selection
Remote Master Volume
Tone Generator
Insert Point
Mix and Tape Output
Rack Kit Included
Rack Space
Mains and DC Power
List Price
J.W, Davis DA-120A
2 mic, 3 mic/line
Yes
Yes, volts not stated
Master Bass & Treble
Yes, VOX on Tel, switch mutes ch 2-5
120w
4-16Ω, 25v, 70v
No
No
No
Yes
Yes
No
2RU
No, mains only
$648.00
TOA BG-1120
1 mic, 1 Tel, 2 line & Module
Yes
24v DC (input 1)
Bass & Treble (rear)
Yes (VOX/switch), 1 mutes all
120w
4Ω, 25v, 70v, MOH
No
No
No
Yes
No, Mix out only
No
2RU
No, mains only
$710.00
TOA A-712
6 mic/line, 2 line & Module
Yes
23v DC (input 1-6)
Master Bass & Treble
Yes (VOX/switch), multi-stage
120w
4Ω, 25v, 70v
No
Yes
No
Yes
Yes
No
2RU
No, mains only
TBA
Inter M A-120
Inter M PA-4000
Bogen C100
Bogen GS100
3 mic, 2 line
5 mic/line, 1 line
1 mic, 1 mic/line, 1 line
4 mic, 1 mic/tel, 1 mic/line, 1 line
No
Yes, via Ch 1
Yes
Yes
No
No
No
Yes, volts not stated
Master 10 band EQ & loudness/Aphex
Master Bass & Treble
Master 5 band EQ
Master Bass & Treble
Yes (VOX/switch), Mic/Tel priority
Yes (VOX), mic 1 mutes all Yes (VOX/switch), mutes inputs 3-6 Yes (VOX/switch), Mic/Tel mutes aux
100w
120w
120w
100w
4Ω, 8Ω, 25v, 70v
4Ω, 70v, 100v
4Ω, 8Ω, 25v, 70v
4Ω, 8Ω, 16Ω, 25v, 70v
No
No
Yes, 5 zones
No
Yes
No
No
No
No
No
Yes, 2 tones
No
Yes
No
Yes
No
Yes
No
No, Mix out only
Yes
No
No
?
No
2RU
2RU
2RU
2RU
No, mains only
No, mains only
No, mains only
No, mains only
$827.20
$390.00
$672.00
$693.00
Page 4 • September 2007
Competitive Comparisons
1RU Mono Mixer Comparison
Australian Monitor MX62
6 mic/line
mono
Master Bass & Treble
Optional VOX muting cards
Yes
Yes
18v DC (all mic inputs)
Optional 4 tone card
1RU
$275.00
Inputs
Mono or Stereo
Equalisation
Priority
Remote Master Level
Mix and Tape Output
Phantom Power
Tone Generator
Rack Space
List Price
Biamp 601
6 mic/line
mono
Master Bass & Treble
VOX, inputs 1-5 mute 6
Yes
No, mix only
24v DC (all mic inputs)
No
1RU
Not Available
Inter M PP-9113
6 mic, 1 phono, 5 line
mono
Master Bass & Treble
VOX, inputs 1-2 mute line inputs
No
Yes
No
No, but has Chime input
1RU
$334.00
Rane MLM-42
4 mic/line
mono
Bass, Mid & Treble per input
No
No
Yes
15v DC (all mic inputs)
No
1RU
$449.00
Bogen CAM8
8 mic/line
mono
None
No
No
Yes
15v DC (all mic inputs)
No
1RU
$877.80
1RU Stereo Mixer Comparison
Australian Monitor MX81
6 mic/line, 2 stereo
stereo
Bass & Treble per input
VOX, Inputs 1-2 mute all
Yes
On inputs 1-6
Yes
15v DC (all mic inputs)
Yes, 4 tones
1RU
$545.00
Inputs
Mono or Stereo
Equalisation
Priority
Remote Master Level
Direct Outputs
Mix and Tape Output
Phantom Power
Tone Generator
Rack Space
List Price
TOA M-243
2 mic/line, 4 stereo
stereo & mono outputs
Master Bass & Treble
VOX, Inputs 1-2 mute all
No
No
Yes
No
No
1RU
$892.00
Ashly DLM-821
4 mic/line, 4 stereo
stereo & mono outputs
None
VOX, Inputs 1-2 mute all
No
No
Yes
18v DC (all mic inputs)
No
1RU
$605.00
120w Power Amplifier Comparison
Australian Monitor AMIS 120P
TOA P-912MK2
Output Power
120w
120w
Outputs
4Ω, 8Ω, 25v, 70v
4Ω, 8Ω, 25v, 70v
Inputs
Line level XLR with loop output Unbalanced or Module
Level Control
Rear
Front
Rack Space
2RU
2RU
Rack Kit Included
Yes
No
Mains and DC Power
Yes
No, mains only
List Price
$385.00
$844.00
Inter M PA-9312
Bogen HT125A
120w
125w
4Ω, 70v, 100v
4Ω, 8Ω, 25v, 70v
Line level XLR with loop output Balanced and hi-z input
Rear
Rear
3RU
3RU
Yes
Yes
Yes
No, mains only
$550.00
$935.00
Stereo Zone Mixer Comparison
Zone Outputs
Mic Inputs
Stereo Line Inputs
Input Equalisation
Output Equalisation
Remote wall panel control
Off Position for music
Assignable Mic Inputs
Priority
Julebox Priority
Expandable
Optional Zone Mic
Phantom Power
Emergency Input
Rack Space
List Price
Australian Monitor ZoneMix 3
3 stereo
2 Mic/Line & 1 Zone Mic
4
2 band EQ on mic/line inputs
5 band EQ per zone
Yes, source select & volume
Yes
Yes, any mic to any zone
Yes, multi-stage
Yes, on stereo input 4
Yes, to 6 stereo zones
Yes
15v DC (all mic inputs)
Yes
1RU
$1,075.00
JBL Soundzone Z32S
Rane CP64
Cloud CX-242
2 stereo & subwoofer
1 stereo, 1 mono
2 stereo
1 Mic
2 Mic
2 Mic
3
4
4
2 band EQ on mic input
None
None
2 band EQ on line signal per zone
7 band EQ per zone
2 band EQ on mic and line per zone
Yes, source select & volume
Yes, source select & volume
Yes, source select & volume
No
No
Yes
Yes, one mic to either zone
Yes, any mic to any zone
Yes, level of both mics in zones
Yes, multi-stage
Yes, multi-stage
Yes, multi-stage
Yes, on stereo input 3
Yes, on stereo input 4
Yes, on stereo input 4
Yes, to multple units
Limited, one pre-mixed output
Yes, to 4 stereo zones
No
No, but paging panel
No
No
15v DC (all mic inputs)
No
Yes
No
Switch muting to cut music
1RU
1RU
1RU
$720.00
$849.00
N/A. Contractor price $479
250w Power Amplifier Comparison
Output Power
Outputs
Inputs
Level Control
Rack Space
Rack Kit Included
Mains and DC Power
List Price
Australian Monitor AMIS 250P
250w
4Ω, 8Ω, 25v, 70v
Line level XLR with loop output
Rear
2RU
Yes
Yes
$725.00
TOA P-924MK2
240w
4Ω, 8Ω, 25v, 70v
Unbalanced or Module
Front
3RU
No
No, mains only
$1,468.00
Inter M PA-9324
240w
4Ω, 70v, 100v
Line level XLR with loop output
Rear
3RU
Yes
Yes
$700.00
Bogen HT250A
250w
4Ω, 8Ω, 25v, 70v
Balanced and hi-z input
Rear
3RU
Yes
No, mains only
$1,507.00
Specifications are subject to change without notice.
J.W. Davis D-250AL
250w
8Ω, 25v, 70v
Unbalanced RCA with loop out
Front
2RU
Yes
No, mains only
$960.00
AMC 30
Page
September
2007
September
2007 • 2007
Page
Page
2007
Page
• September
September
20075
Page
5 55
•5••September
30 Watt 2RU MIXER-AMPLIFIER
•
•
•
•
•
•
•
•
•
3 balanced XLR mic/dual RCA line inputs
30 watt output power
2 Rack units in height
70 volt or 4 ohm operation
Master treble and bass control
Channel 1 has priority over channels 2 & 3 (defeatable)
Facility to add a tone generator module
Tape output (pre master)
Balanced line output
The Australian Monitor Installation Series AMC line of amplifiers
takes the heritage & reliability of our famous AMIS series &
integrates these features into a low cost amplifier format for
applications where reliability is everything, but the more elaborate
features of our AMIS series are not required. The 30 watt version of
the AMC series is a 2 RU mixer amplifier featuring 70 volt line (100v
230/240V version) & 4 ohm outputs & 3 universal mic/line inputs.
Master volume & overall treble/bass controls are provided, along
with Voice triggered muting (defeatable) giving channel 1 priority
over inputs 2 & 3. There is also facility to internally add a tone
generator card.
The Australian Monitor AMC series give the contractor a low cost
alternative in applications that are cost sensitive, but still require a
high quality of sound reproduction & reliability.
Specifications are subject to change without notice.
SPECIFICATIONS
Power output:
30W
Outputs:
4 Ohms, 70/100V
THD before clipping
0.5%
Inputs
3x (Mic/Aux)
Input connectors
3x (XLR/RCA)
Mic sensitivity
1mV+/-0.2mV
AUX sensitivity
0.5V+/-100mV
S/N ratio
> 75dBr
Bandwidth
On 70V terminals
85Hz-15kHz
(-3dB +0dB)
Tone Controls
Bass @ 100Hz
+/- 12 dB
Treble @ 10kHz
+/- 9 dB
Power source (Switchable)
115V 60 Hz
230-240V 50Hz
Current draw (full power)
.73 A
Fuses
1A - AC mains & DC
Line Out
1V
Tape Out
300mV
Mic 1 Automatic
Priority over Mic 2/3
Size
19” W x 3.5” H x 7.5” D
Protections
1) Short circuit
2) No Thermal
Output Regulation
96%
Net Weight
13.2lb
Shipping Dimensions
20.1” W x 5.7” H x 11.7”
D
Shipping Weight
16.5lb
Warranty
1 year
AMC 60
Page 6 • September 2007
60 Watt 2RU MIXER-AMPLIFIER
•
•
•
•
•
•
•
•
•
3 balanced XLR mic/dual RCA line inputs
60 watt output power
2 Rack units in height
70 volt or 4 ohm operation
Master treble and bass control
Channel 1 has priority over channels 2 & 3 (defeatable)
Facility to add a tone generator module
Tape output (pre master)
Balanced line output
The Australian Monitor Installation Series AMC line of amplifiers
takes the heritage & reliability of our famous AMIS series &
integrates these features into a low cost amplifier format for
applications where reliability is everything, but the more elaborate
features of our AMIS series are not required. The 60 watt version of
the AMC series is a 2 RU mixer amplifier featuring 70 volt line (100v
230/240V version) & 4 ohm outputs & 3 universal mic/line inputs.
Master volume & overall treble/bass controls are provided, along
with Voice triggered muting (defeatable) giving channel 1 priority
over inputs 2 & 3. There is also facility to internally add a tone
generator card. Protection includes short circuit and thermal
detection and shut-down.
The Australian Monitor AMC series give the contractor a low cost
alternative in applications that are cost sensitive, but still require a
high quality of sound reproduction & reliability.
Specifications are subject to change without notice.
SPECIFICATIONS
Power output:
60W
Outputs:
4 Ohms, 70/100V
THD before clipping
0.5%
Inputs
3x (Mic/Aux)
Input connectors
3x (XLR/RCA)
Mic sensitivity
1mV+/-0.2mV
AUX sensitivity
0.5V+/-100mV
S/N ratio
> 75dBr
Bandwidth
On 70V terminals
75Hz-15kHz
(-3dB +0dB)
Tone Controls
Bass @ 100Hz
+/- 12 dB
Treble @ 10kHz
+/- 9 dB
Power source (Switchable)
115V 60 Hz
230-240V 50Hz
Current draw (full power)
1.38 A
Fuses
1A - AC mains & DC
Line Out
1V
Tape Out
300mV
Mic 1 Automatic
Priority over Mic2/3
Size
19” W x 3.5” H x 11.1” D
Protections
1) Short circuit
2) Thermal at 95%
Output Regulation
96%
Net Weight
18.7lb 1
Shipping Dimensions
20.1” W x 5.7” H x 11.7”D
Shipping Weight
23.1 lb
Warranty
1 year
AMC 120
Page
September
2007
September
2007 • 2007
Page
Page
2007
Page
• September
September
20077
Page
7 77
•7••September
120 Watt 2RU MIXER-AMPLIFIER
•
•
•
•
•
•
•
•
•
3 balanced XLR mic/dual RCA line inputs
120 watt output power
2 Rack units in height
70 volt or 4 ohm operation
Master treble and bass control
Channel 1 has priority over channels 2 & 3 (defeatable)
Facility to add a tone generator module
Tape output (pre master)
Balanced line output
The Australian Monitor Installation Series AMC line of amplifiers
takes the heritage & reliability of our famous AMIS series &
integrates these features into a low cost amplifier format for
applications where reliability is everything, but the more elaborate
features of our AMIS series are not required. The 120 watt version
of the AMC series is a 2 RU mixer amplifier featuring 70 volt line
(100v 230/240V version) & 4 ohm outputs, & 3 universal mic/line
inputs.
Master volume & overall treble & bass controls are provided, along
with Voice triggered muting (defeatable) giving channel 1 priority
over inputs 2 & 3. There is also facility to internally add & a tone
generator card. Protection includes short circuit and thermal
detection and
shut-down.
The Australian Monitor AMC series give the contractor a low cost
alternative in applications that are cost sensitive, but still require a
high quality of sound reproduction & reliability.
Specifications are subject to change without notice.
SPECIFICATIONS
Power output:
120W
Outputs:
4 Ohms, 70/100V
THD before clipping
0.5%
Inputs
3x (Mic/Aux)
Input connectors
3x (XLR/RCA)
Mic sensitivity
1mV+/-0.2mV
AUX sensitivity
0.5V+/-100mV
S/N ratio
> 80dBr
Bandwidth
On 70V terminals
75Hz-15kHz
(-3dB +0dB)
Tone Controls
Bass @ 100Hz
+/- 12 dB
Treble @ 10kHz
+/- 9 dB
Power source (Switchable)
115V 60 Hz
230-240V 50Hz
Current draw (full power)
2.5 A
Fuses
1A - AC mains & DC
Line Out
1V
Tape Out
300mV
Mic 1 Automatic
Priority over Mic2/3
Size
19” W x 3.5” H x 11.1” D
Protections
1) Short circuit
2) Thermal at 95%
Output Regulation
96%
Net Weight
23.1lb
Shipping Dimensions
20.1” W x 5.7” H x 11.7” D
Shipping Weight
27.6 lb
AMIS 60
Page 8 • September 2007
4 Input 60 Watt MIXER-AMPLIFIER
Inputs
The AMIS60 has four universal input channels with separate level controls.
Each channel will accept balanced or unbalanced microphone, line and
auxiliary inputs. The unit has industry standard XLR microphone sockets and
dual RCA auxiliary sockets for each channel. An electronically-balanced 600
ohm telephone input for paging is also provided. An insert point is also featured
on the rear panel for those applications where an additional EQ or feedback
eliminator may be required.
Outputs
The AMIS60 features 70 volt and 8 ohm isolated transformer outputs, plus a
tape recorder output by means of dual RCA sockets. A balanced 700mV XLR
output is also provided to feed up to 6 power amplifiers. A vox triggered relay
output is also available on the rear panel for activation of external devices from
the vox muting circuit. In most cases this would be used as a muting bypass
relay, which when used with the appropriate external attenuator will maintain
paging levels irrespective of the attenuator setting.
VCA Control
The master volume can be controlled remotely. External VCA control would
normally be via a pot connected to a two wire rear panel barrier strip.
Speaker Zone Selector
A six position push button speaker zone selector with overriding “all call” is
located on the front panel. Each of the six zone selectors switch the 70 volt
speaker line output to 6 separate speaker zones. The “all call” selector
overrides all 6 zones regardless of their on/off condition and places the 70 volt
output to all 6 zones.
Tone Generator
The AMIS60 comes standard with an in-built four tone generator module. Tones
include Bell, Pre-announce Chime, Alert Tone and Evacuate Tone. Any of these
tones may be activated from a simple contact closure connected to the rear
panel of the amplifier. A Pre-announce defeat switch is located on the front
panel.
Muting
VOX muting is standard on the AMIS60. A mic or line signal on channels 1 or 2
will mute channels 3 and 4. The muting function can be disabled via an internal
link.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
60 Watts RMS
Maximum Load
80 Ohms @ 70 Volts
Power Bandwidth
60Hz - 17kHz (- 3dB)
Frequency Response
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion
0.5% @ 1kHz
rated power
Signal To Noise Ratio
-74dB all controls center
Tone Controls
Bass @ 100Hz
Boost +12dB Cut -12dB
Treble @ 10kHz
Boost +9dB Cut -9dB
Input Sensitivity
Mics: 1mV @ 200 Ohms
Aux: 150mV @ 47K Ohms
Outputs
Speaker: 70 Volts, 4 & 8 Ohm
Tape: 350mV @10KOhms
Line: Balanced 700mV
Phantom Power
18 V DC Mic ins- Switch
Controls
4 input channel gain
1 Bass control
1 Treble control
1 Master gain control
6 Speaker zone selector
1 Speaker “all call” selector
1 Pre-announce defeat switch
1 Phantom Power switch
Tone Generators
Four tone generator with Bell,
Pre-Announce, Alert and Evac
Protection
Soft limiter for overload
protection, plus AC and
DC fuses.
Muting
Channels 1 and 2 will
mute channels 3 and 4
Indicators
Power “on” LED
Power Source
120VAC 60Hz
3 pin IEC connector; 24VDC
Power Consumption
125 Watts
Dimensions
3.5" H x 19" W x 13" D
Weight
22 lbs.
AMIS 120
Page
September
2007
September
2007 • 2007
Page
Page
2007
Page
• September
September
20079
Page
9 99
•9••September
4 Input 120 Watt MIXER-AMPLIFIER
Description
The AMIS120 is a 4 channel, 120 watt mixer amplifier suitable for rack or desk
mounting. The amplifier is a self contained compact unit of solid steel
construction.
Inputs
The AMIS120 has four universal input channels with separate level controls.
Each channel will accept balanced or unbalanced microphone, line and auxiliary
inputs. The unit has industry standard XLR microphone sockets and dual RCA
auxiliary sockets for each channel. An electronically-balanced 600 ohm
telephone input for paging is also provided. An insert point is also featured on
the rear panel for those applications where an additional EQ or feedback
exterminator may be required.
Outputs
The AMIS120 features 70 volt, 4 & 8 ohm isolated transformer outputs, plus a
tape recorder output by means of dual RCA sockets. A balanced 700mV XLR
output is also provided to feed up to six power amplifiers. A vox triggered relay
output is also available on the rear panel for activation of external devices from
the vox muting circuit. In most cases this would be used as a muting bypass
relay, which when used with the appropriate external attenuator will maintain
paging levels irrespective of the attenuator setting.
VCA Control
The master volume can be controlled remotely. External VCA control would
normally be via a pot connected to a two wire rear panel barrier strip.
Speaker Zone Selector
A six position push button speaker zone selector with overriding “all call” is
located on the front panel. Each of the six zone selectors switch the 70 volt
speaker line output to six separate speaker zones. The “all call” selector
overrides all 6 zones regardless of their on/off condition and places the 70 volt
output to all six zones.
Tone Generator
The AMIS120 comes standard with an in-built four tone generator module. Tones
include Bell, Pre-Announce Chime, Alert Tone and Evacuate Tone. Any of these
tones may be activated from a simple contact closure connected to the rear
panel of the amplifier. A Pre-announce defeat switch is located on the front
panel.
Muting
VOX muting is standard on the AMIS120. A mic or line signal on channels 1 or 2
will mute channels 3 and 4. The muting function can be disabled via an internal
link.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
120 Watts RMS
Maximum Load
40 Ohms @ 70 Volts
Power Bandwidth
60Hz - 17kHz (- 3dB)
Frequency Response
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion
0.5% @ 1kHz
rated power
Signal To Noise Ratio
-74dB all controls center
Tone Controls
Bass @ 100Hz
Boost +12dB Cut -12dB
Treble @ 10kHz
Boost +9dB Cut -9dB
Input Sensitivity
Mics: 1mV @ 200 Ohms
Aux: 150mV @ 47K Ohms
Outputs
Speaker: 70 Volts, 4 & 8 Ohm
Tape: 350mV @10KOhms
Line: Balanced 700mV
Phantom Power
18 V DC Mic ins- Switch
Controls
4 input channel gain
1 Bass control
1 Treble control
1 Master gain control
6 Speaker zone selector
1 Speaker “all call” selector
1 Pre-announce defeat switch
1 Phantom Power switch
Tone Generators
Four tone generator with Bell,
Pre-Announce, Alert and Evac
Protection
Soft limiter for overload
protection, plus AC and
DC fuses.
Muting
Channels 1 and 2 will
mute channels 3 and 4
Indicators
Power “on” LED
Power Source
120VAC 60Hz
3 pin IEC connector; 24VDC
Power Consumption
250 Watts
Dimensions
3.5" H x 19" W x 13" D
Weight
26.5 lbs.
AMIS 120XL
Page 10 • September 2007
8 Input 120 Watt MIXER-AMPLIFIER
Description
The AMIS120XL is an 8 channel, 120 watt mixer amplifier suitable for
rack or desk mounting. The amplifier is a self contained compact unit of
solid steel construction. This amplifier features a status LED.
Inputs
The AMIS120XL has eight universal input channels with separate level
controls. Each channel will accept balanced or unbalanced microphone,
line and auxiliary inputs. The unit has industry standard XLR microphone
sockets and dual RCA auxiliary sockets for each channel. Rear panel dip
switches per channel allow the adjustment of line input sensitivity. An
insert point is also featured on the rear panel for those applications where
an additional EQ or Feedback Exterminator may be required. An
electronically-balanced 600 ohm telephone input for paging is also
provided.
Outputs
The AMIS120XL features 70 volt, 4 & 8 ohm isolated transformer outputs,
plus a tape recorder output by means of dual RCA sockets. A balanced
700mV XLR output is also provided to feed up to 6 power amplifiers. A
vox triggered relay output is also available on the rear panel for activation
of external devices from the vox muting circuit. In most cases this would
be used as a muting bypass relay, which when used with the appropriate
external attenuator will maintain paging levels irrespective of the
attenuator setting.
VCA Control
The master volume level can be controlled remotely. External VCA control
would normally be via a pot connected to a two wire rear panel barrier
strip.
Tone Generator
The AMIS120XL comes standard with an in-built four tone generator
module. Tones include Bell, Pre-announce Chime, Alert Tone and
Evacuate Tone. Any of these tones may be activated from a simple
contact closure connected to the rear panel of the amplifier.
Muting
Multiple levels of VOX muting is standard on the AMIS120XL. A mic or
line signal on channels 1 will mute channels 2 to 8, on channel 2 will
mute 3-8 and channel 3, will mute 4-8. The muting function can be
disabled via an internal link. A vox triggered relay output is also available
on the rear panel for activation of external devices from the vox muting
circuit. In most cases this would be used as a muting bypass relay, which
when used with the appropriate external attenuator will maintain paging
levels irrespective of the attenuator setting.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
120 watts RMS
Maximum Load
40 Ohms @ 70 Volts
Power Bandwidth
60Hz - 17kHz (- 3dB)
Frequency Response
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion
0.5% @ 1KHz rated power
Signal To Noise Ratio
-74dB with all controls at center
Tone Controls
Bass @ 100Hz
Boost +12dB Cut -12dB
Mid @ 600Hz
Boost +12dB Cut -12dB
Treble @ 10kHz
Boost +9dB Cut -9dB
Inputs
Eight mic/aux universal inputs
with XLR female and dual RCA
plugs ; 600 ohm transformer
balanced telephone paging input
Input Sensitivity
Mics: 1mV @ 200 Ohms
Aux: 150mV @ 47K Ohms
with 9, 12, 15dB Pads
Outputs
Speaker: 70 Volts, 4 & 8 Ohms
Tape: 350mV @ 10K Ohms
Line: Balanced 700mV
Phantom Power
18V DC on all Mic ins- Switch
Controls
8 Input channel gain controls
1 Bass control
1 Mid Control
1 Treble control
1 Master gain control
VCA rear panel strip
Dip Switch per Channel for line
sensitivity and phantom power
and a vox relay ouput
Tone Generators
Four tone generator with Bell,
Pre-Announce, Alert and Evac
Muting
Channel 1 will mute chans. 2 to
8, channel 2 mutes 3 - 8, channel
3 mutes 4 - 8. Also a vox
relay to external devices.
Indicators
Power “on” & signal present LEDs
Dimensions:
3.5" H x 19" W x 13" D
Weight 26.5lb
AMIS 250
Page
11
September
2007
September
2007 • Page
11
Page
2007
Page
11
• September
September
2007
Page
1111
• ••September
2007
6 Chan 250 Watt MIXER-AMPLIFIER
Description
The AMIS250 is a 6 channel, 250 watt mixer amplifier suitable for rack or
desk mounting. The amplifier is a self contained compact unit of solid
steel construction.
Inputs
The AMIS250 has six universal input channels with separate level
controls. Each channel will accept balanced or unbalanced microphone,
line and auxiliary inputs. The unit has industry standard XLR microphone
sockets and dual RCA auxiliary sockets for each channel. An
electronically-balanced 600 ohm telephone input for paging is also
provided. An insert point is also featured on the rear panel for those
applications where an additional EQ or feedback exterminator may be
required.
Outputs
The AMIS250 features 70 volt and 4 ohm isolated transformer outputs,
plus a tape recorder output by means of dual RCA sockets. A balanced
700mV XLR output is also provided to feed up to 6 power amplifiers.
Tone Generator
The AMIS250 comes standard with an in-built four tone generator
module. Tones include Bell, Pre-announce Chime, Alert Tone and
Evacuate Tone. Any of these tones may be activated from a simple
contact closure on the rear panel of the amplifier.
Muting
VOX muting is standard on the AMIS250. A mic or line signal on channels
1 or 2 will mute channels 3, 4, 5 and 6. The muting function can be
disabled via an internal link.
Phantom Power
Phantom Power (18V DC) is available from all mic inputs. A rear panel
phantom power on/off switch is also provided.
Protection
Internal current limiting protects the amplifier from both overload and
overdrive conditions. Australian Monitor Installation Series amplifiers
feature a protection network that provides greater stability and
performance. Our amplifiers are recognised worldwide for their reliability
and this is due to the extensive levels of current limiting which protect the
amplifiers from both overload and overdrive conditions.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
250 watts RMS
Maximum Load
20 Ohms @ 70 Volts
Power Bandwidth
60Hz - 17kHz (- 3dB)
Frequency Response
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion
0.5% @ 1kHz rated power
Signal To Noise Ratio
-74dB with all controls at center
Tone Controls
Bass @ 100Hz:
Boost +12dB Cut -12dB
Mid @ 600Hz:
Boost +12dB, Cut -12dB
Treble @ 10kHz:
Boost +9dB Cut -9dB
Inputs
Six mic/aux universal inputs
with XLR female mic sockets
and dual RCA Phono aux
sockets; 600 ohm transformer
balanced telephone paging input
Input Sensitivity
Mics: 1mV @ 200 Ohms
Aux: 150mV @ 47K Ohms
Outputs Speaker: 70 V, 4 Ohms
Tape: 350mV @ 10K Ohms
Line: Balanced 700mV
Phantom Power
18 Volts DC on all Mic inputs
Controls
6 Input channel gain controls
1 Bass control
1 Mid Control
1 Treble control
1 Master gain control
1 Phantom Power on/off switch
Tone Generators
Four tone generator with Bell,
Pre-Announce, Alert and Evac
Muting
Built-in VOX muting.
Channels 1 and 2 will mute
channels 3, 4, 5 and 6
Indicators
Power “on” and “Protect” LED
Power Source
120VAC 60Hz 3 pin IEC; 24VDC
Power Consumption
400 Watts
Dimensions
3.5" H x 19" W x 13" D
Weight 33.1lb
AMC MIX
Page 12 • September 2007
3 Chan MIXER
·
·
·
·
·
3 Mic/line input mono mixer
Master Volume, overall treble & bass controls
1 RU
Optional tone generator
On board priority
The Australian Monitor Installation Series AMC-MIX mixer brings the
affordability & ease of use of the AMC series amplifiers and offers
accommodations a low cost mixer for applications where reliability is
everything but the more elaborate features of the MX mixers series are
not required.
The AMC-MIX is a 1 RU mixer that features 3 universal mic/line inputs.
Master volume & overall treble & bass controls are provided, along with
vox triggered muting (defeatable) giving channel 1 priority over channels
2 & 3. There is also facility to add an optional on board tone generator
card. The AMC-MIX gives the contractor a low cost alternative in
applications that are price sensitive but still require reliability & a high
level of sound reproduction.
OPTIONS (not included)
AMMUTE1 Single Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at
channel 1 and the channel volume is turned up
AMMUTE3 Triple Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1
• Allows for muting of channels 3 and higher when signal is present at channel 2
• Allows for muting of channels 4 and higher when signal is present at channel 3
• Ability to adjust threshold of the trigger signal along with the the release time of the
ducked signal
AMVCA Remote Master Volume Control
• Enables the end user to utilize a localized volume control
• Remote volume control is pre the mixers front panel master volume and thus can
be set up to give a limited volume range to the end user
• Supplied with RC1 remote volume control as a complete kit ready for installation
AMTONE1 Tone Module
• Generates four tones: Evacuation, Alert, Bell and Pre Announce Chime
Specifications are subject to change without notice.
SPECIFICATIONS
FREQUENCY RESPONSE
20Hz - 20kHz (+0,-3dB)
DISTORTION
< 0.5% @ 1kHz (THD)
SIGNAL TO NOISE RATIO
> 84dB (pots at center)
CROSSTALK
> 60dB
TONE CONTROLS
BASS @100HZ +/- 12dB
TREBLE @10KHZ +/9dB
SENSITIVITY
Mic Sens 0.7mV, -61dBu
Imp 1k3ohm
RCA 500mV, -4dBu Imp
>100kohm
MAX LEVEL IN
XLR mic -20dBu
RCA >30dBu
MAX LEVEL OUT
+14dBu
MASTER OUT
Nominal Level 0dBu into
1k Ohm Imp 100
Ohm
MONO TAPE OUT
Nom -16dB into 10k Ohm
Imp 10k Ohm
POWER INPUT
20V AC via
2.1mmx5.5mm
barrel
POWER CONSUMPTION
7 VA (max)
DIMENSIONS HxWxD
1.75”x19”x7.54”
WEIGHT
Net 5.5lb
Shipping 7.7lb
MX 61
Page
13
September
2007
September
2007 • Page
13
Page
2007
Page
13
• September
September
2007
Page
1313
• ••September
2007
6 Channel 1RU MIXER
· 6 input mono mixer
· XLR input switchable between mic & line level
· 15dB +/- gain trim control per input
· Input 1 is switchable to be pre/post master
· 24VDC or mains power operation
· Optional remote VCA/Tone generator/ Muting boards
· Whisper quiet operation
· Dual color signal present indication LED per input
The Australian Monitor Installation Series MX61 mixer brings a range of
new features to the AMIS standard 1 RU mixer range. The MX61 mixer
features the new Australian Monitor Standard (AMS) input section which
has an XLR input switchable between mic & line level, dual RCA line
inputs, signal present LED indication, individually switchable phantom
power, & +/- 15dB of gain trim available per input. The MX61 also boasts
whisper quiet operation, 4 segment output level indication & balanced line
output, record output & headphone outputs. The MX61 has 6 AMS inputs
to one output & will operate via 110 or 220-240 VAC or 24VDC via an
external 24 volt power supply. Optional remote VCA volume control, tone
generators & muting boards are also available for the MX61. The MX61
mixer is extremely versatile & represents excellent value for money.
OPTIONS (not included)
AMMUTE1 Single Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at
channel 1 and the channel volume is turned up
AMMUTE3 Triple Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1
• Allows for muting of channels 3 and higher when signal is present at channel 2
• Allows for muting of channels 4 and higher when signal is present at channel 3
• Ability to adjust threshold of the trigger signal along with the the release time of the
ducked signal
AMVCA Remote Master Volume Control
• Enables the end user to utilize a localized volume control
• Remote volume control is pre the mixers front panel master volume and thus can
be set up to give a limited volume range to the end user
• Supplied with RC1 remote volume control as a complete kit ready for installation
AMTONE1 Tone Module
• Generates four tones: Evacuation, Alert, Bell and Pre Announce Chime
Specifications are subject to change without notice.
SPECIFICATIONS
FREQUENCY RESPONSE
20Hz - 20kHz (+0,3dB)
TOTAL HARMONIC
DISTORTION
< 0.1% @ 1kHz
SIGNAL TO NOISE RATIO
> 90dB (all pots at
center)
CROSSTALK
>70dB
TONE CONTROLS
BASS @ 100HZ +/- 12dB
MID @ 1.6KHZ +/- 12dB
TREBLE @ 10KHZ +/12dB
SENSITIVITY
Mic Sens 4.36mV, -45dBu
Imp 1k3ohm (Trim center- 0dB)
Line Sens 0.775V, 0dBu
Imp >100k
RCA 200mV, -12dBu
Imp 30kohm
MAX LEVEL IN
XLR mic -15dBu line
+30dBu
RCA >30dBu
MAX LEVEL OUT
+21dBu
PHANTOM POWER
15V DC
MASTER OUT
Nominal Level 0dBu
into 1kohm Imp 100ohm
MONO HEADPHONE OUT
Nom -6dB into 200ohm
Imp 10ohm
MONO REC OUT
Nom -12dB into
10kohm
Imp 10kohm
POWER INPUT
AC: 115V/60Hz, 3 pin IEC,
DC: 24 Volts
POWER CONSUMPTION
(MAX)
7VA
FUSES
MAINS (115V) 120mA
DIMENSIONS H x W x D
1.75“x19”x7.2”
WEIGHT
NET 6.1lb
SHIPPING 8.3lb
MX 81
Page 14 • September 2007
8 Channel 1 RU MIXER
•
•
•
•
•
•
•
•
8 input mono mixer
XLR input switchable between mic & line level
15dB +/- gain trim control per input
Input 1 is switchable to be pre/post master
24VDC or mains power operation
Optional remote VCA/Tone generator/ Muting boards
Whisper quiet operation
Dual color signal present indication LED per input
The Australian Monitor Installation Series MX81 mixer brings a range of
new features to the AMIS standard 1 RU mixer range. The MX81 mixer
features the new Australian Monitor Standard (AMS) input section which
has an XLR input switchable between mic & line level, dual RCA line
inputs (on the first 6 inputs only), signal present LED indication,
individually switchable phantom power, & +/- 15dB of gain trim & treble &
bass controls available per input. The MX81 also boasts whisper quiet
operation, 4 segment output level indication & balanced line output,
record output & headphone outputs. The MX81 has 6xAMS and 2xXLR
inputs to one output & will operate via 110 or 220-240 VAC or 24VDC via
an external 24 volt power supply. Optional remote VCA volume control,
tone generators & muting boards are also available for the MX81. The
MX81 mixer is extremely versatile & represents excellent value for
money.
OPTIONS (not included)
AMMUTE1 Single Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at
channel 1 and the channel volume is turned up
AMMUTE3 Triple Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1
• Allows for muting of channels 3 and higher when signal is present at channel 2
• Allows for muting of channels 4 and higher when signal is present at channel 3
• Ability to adjust threshold of the trigger signal along with the the release time of the
ducked signal
AMVCA Remote Master Volume Control
• Enables the end user to utilize a localized volume control
• Remote volume control is pre the mixers front panel master volume and thus can
be set up to give a limited volume range to the end user
• Supplied with RC1 remote volume control as a complete kit ready for installation
AMTONE1 Tone Module
• Generates four tones: Evacuation, Alert, Bell and Pre Announce Chime
SPECIFICATIONS
FREQUENCY RESPONSE
20Hz - 20kHz (+0,3dB)
DISTORTION
> 0.1% @ 1kHz THD
SIGNAL TO NOISE RATIO
> 90dB (all pots at
center)
CROSSTALK
>70dB
TONE CONTROLS
BASS @ 100HZ +/- 12dB
TREBLE @ 10KHZ +/12dB
SENSITIVITY
Mic Sens 4.36mV, 45dBu
(Trim in center 0dB)
Imp 1k3ohm
Line Sens 0.775V, 0dBu
Imp >100k
RCA 200mV, -12dBu
Imp 30k Ohm
MAX LEVEL IN
XLR mic -15dBu line
+30dBu
RCA
>30dBu
MAX LEVEL OUT
+21dBu
PHANTOM POWER
15V DC
MASTER OUT
Nominal Level 0dBu into
1k Ohm Imp 100
Ohm
MONO HEADPHONE OUT
Nom -6dB into 200
Ohm
Imp 10 Ohm
MONO REC OUT
Nom -12dB into 10kohm
Imp 10k Ohm
POWER INPUT
AC: 115V/60Hz, 3 pin
IEC320-C14
DC: 24 Volts
POWER CONSUMPTION
7 VA (max)
FUSES
MAINS (115V) 120mA
DIMENSIONS H x W x D
1.75“x19”x7.2”
WEIGHT
NET 6.1lb
SHIPPING 3.75kg (8.3lb)
Specifications are subject to change without notice.
SM 16 / SM12
Page
15
September
2007
September
2007 • Page
15
Page
2007
Page
15
• September
September
2007
Page
1515
• ••September
2007
SM16
• 8 Mic channels & 4 Stereo channels
• Mic channels features• XLR/1/4” jack input
• Phantom power
• low cut switch gain trim
• HF, sweepable mid range & LF equalization
• EQ on/bypass button
• Aux 1 pre/aux 2 post
• Pan
• Channel PFL/Mute/fader
• Stereo channels features• Gain trim
• HF, mid & LF equalization
• EQ on/bypass button
• Aux 1 pre/aux 2 post
• Pan
• Channel PFL/Mute/fader
• Stereo output bus & L/R alt output bus
• Control room output
• Headphone out c/w level
•Tape in/ record out
SM12
• 4 Mic channels & 4 Stereo channels
• Other features same as above
Specifications are subject to change without notice.
AMIS 120P
Page 16 • September 2007
120 Watt 70 Volt/ 8 Ohm AMPLIFIER
Description
The AMIS120P is a 120 watt power amplifier with outputs for 4 and 8
ohms and 70 volt line. It may be desk or rack mounted. The AMIS120P
features a flat screwdriver accessible gain control on the rear panel.
This amplifier features a status LED.
Inputs and Outputs
The AMIS120P features a balanced line level XLR input with a parallel
output to feed additional power amplifiers. The unit has industry
standard 3 pin XLR microphone sockets. The AMIS120P features 70
volt, 8 and 4 ohm isolated transformer outputs via a rear panel barrier
strip.
Protection
Internal current limiting protects the amplifier from both overload and
overdrive conditions. Should the amplifier be overdriven, a current
limiter will protect the unit, and in a worst case scenario the amplifier will
shut down until the problem is resolved. Once the problem is fixed
(shorted speaker line or overdriven input), the amplifier will
automatically reset and continue operation. The AMIS120P features
generous heatsinking. Australian Monitor Installation Series amplifiers
feature a protection network that provides greater stability and
performance. Our amplifiers are recognized worldwide for their
reliability and this is due to the extensive levels of current limiting which
protect the amplifiers from both overload and overdrive conditions.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
120 Watts RMS
Maximum Load
40 Ohms @ 70 Volts
Power Bandwidth
60Hz - 17kHz (- 3dB)
Frequency Response
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion
0.5% @ 1kHz rated
power
Signal To Noise Ratio
-80dB
Input Sensitivity
700mV
Outputs
70V, 4 Ohm, 8 Ohm
Controls
One gain control on rear
of the unit via flathead
screwdriver control
Indicators
Power “on” LED
Power Source
120VAC 60Hz 3 pin IEC
connector; 24VDC
Power Consumption
300 Watts
Protection
Current Limiter
protection, plus AC and
DC fuses
Dimensions
3.5" H x 19" W x 11" D
Weight
26.5lb
Rack Mounting
Standard
AMIS 250P
Page
17
September
2007
September
2007 • Page
17
Page
2007
Page
17
• September
September
2007
Page
1717
• ••September
2007
250 Watt 70 Volt/ 8 Ohm AMPLIFIER
Description
The AMIS250P is a 250 watt power amplifier with outputs for 4 ohms and
70 volt line. It may be desk or rack mounted. The AMIS250P features a flat
screwdriver accessible gain control on the rear panel.
Inputs
The AMIS250P features one signal input. The unit has industry standard 3
pin XLR microphone sockets. Two line level sockets are provided for
bridged in/out connection.
Outputs
The AMIS250P features 70 volt and 4 ohm isolated transformer outputs.
Protection
Internal current limiting protects the amplifier from both overload and
overdrive conditions. The AMIS250P also features protection in the form of
excess temperature auto cut out. A built-in auto temperature sensing fan
will turn on at a factory default level but in most situations, will never be
required. Australian Monitor Installation Series amplifiers feature a
protection network that provides greater stability and performance. Our
amplifiers are recognized worldwide for their reliability and this is due to the
extensive levels of current limiting which protect the amplifiers from both
overload and overdrive conditions.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
250 Watts RMS
Maximum Load
20 Ohms @ 70 Volts
Power Bandwidth
60Hz - 17kHz (- 3dB)
Frequency Response
60Hz - 23kHz (- 3dB)
Distortion
0.5% @ 1 kHz rated
power (THD)
Signal To Noise Ratio 8
80dB
Input Sensitivity
700mV Outputs 70V,
4 Ohm
Controls
One gain control on
rear of the unit via
flathead screwdriver
control
Indicators
Power “on” and
“Protect” LED
Power Source
120VAC 60Hz 3 pin
IEC connector;
24VDC
Power Consumption
400 Watts
Protection
Current Limiter
protection, plus AC
and DC fuses
Dimensions HWD
3.5" x 19" x 13"
Weight
33.1lb
Rack Mounting
Standard
AMIS 1202P
Page 18 • September 2007
2 chan. 120 Watt 70 Volt/ 8 Ohm AMP
Description
The AMIS1202P is a dual channel 120W + 120W power amplifier
designed to deliver continuous full range performance in a compact and
reliable package. The AMIS1202P is two independent amplifiers in the
one chassis making it the perfect choice for multi-zone or multi-channel
applications.
Inputs and Outputs
The AMIS1202P provides dual balanced XLR inputs (male and female)
per channel. These two inputs are wired in parallel enabling a line level
‘split’ to be taken from the second input of each channel. 70 volt line and
4/8 ohm outputs are available via the rear panel barrier strip.
Controls and Metering
A recessed input attenuation control for each channel is included on the
rear panel. These pots are accessible using a screwdriver. The
AMIS1202P features a signal-present LED per channel and power-on
LED.
Protection
The AMIS1202P features ‘slow start’ and dual AC and DC fuse protection.
Also featured is automatic speaker protection. The AMIS1202P includes
generous heat sinking for reliable operation in even the most extreme
conditions. Australian Monitor Installation Series amplifiers feature a
protection network that provides greater stability and performance. Our
amplifiers are recognized worldwide for their reliability and this is due to
the extensive levels of current limiting which protect the amplifiers from
both overload and overdrive conditions.
Specifications are subject to change without notice.
SPECIFICATIONS
Power Output
120 Watts per channel
Maximum Load
40 Ohms on 70 Volt
line setting
Frequency Response
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion
0.5% at 1kHz
(1 Watt - full power)
Signal To Noise Ratio
-80dB at 70V
-80dB at 8 Ohms
-80dB at 4 Ohms
Input Sensitivity
0.5 Volt RMS - 70 Volt
Input Impedance
10K Ohms
Input Connection
Active balanced input
with male and female
3 pin XLR input/output
Outputs
70 Volt line and 4/8
Ohm via rear panel
barrier strip.
Line out to feed
additional amplifiers
from one of the
paralleled XLR input
Controls
Front power
switch;
Recessed rear input
attenuator (per chan)
Metering/Indicators
Signal-present LED
per chan.
Power Source
120VAC 60Hz 3 pin
IEC; 24VDC
Power Consumption
400 Watts (maximum)
Protection
Fuses for overload &
short circuit protect,
High temperature trip
(at 120¼C), DC Output
Sensing (disconnects
load if DC is present)
Dimensions:
3.5" H x 19" W x 11" D
Weight
3.1lb
Rack Mounting
Standard
AMIS 480P
Page
19
September
2007
September
2007 • Page
19
Page
2007
Page
19
• September
September
2007
Page
1919
• ••September
2007
4 Chan. 80 Watt 70 Volt/ 8 Ohm AMP
The Australian Monitor Installation Series AMIS480P is a robust, highly
featured 4 channel power amplifier. Offering 4 independent channels,
each delivering 80 watts into 4 ohms or 70/100 volt line, the AMIS480P is
designed to operate in extreme conditions to give the contractor the
most reliable 4 channel amplifier available today.
Engineered with maximum attention to channel isolation, with individual
ground lift switches and level control for each channel, the AMIS480P
will operate as 4 individual amplifiers in a rack space friendly, 2RU
chassis.
For ease of installation, each channel input can be routed to the next
channel via rear panel link switches, eliminating the need for daisy
chaining or Y-split cables. The AMIS480P also offers signal present and
clip LED indicators for each channel as well as a thermal protect
indicator.
The AMIS480P is a significant advance in 4 channel amp design offered
at a contractor friendly price.
Specifications are subject to change without notice.
SPECICIATIONS
Power Output
4 x 80W
Freq. Response (1W)
80Hz - 20kHz
DISTORTION
1% THD, all
channels driven
Power Bandwidth
85Hz - 20kHz
S/N Ratio
94dB (ref 100V)
Crosstalk
1kHz 80dB; 20Hz 20kHz Better than
60dB
Input Sensitivity
0.775V RMS
(0dBu)
Input Impedance
20K
Voltage Gain (pot at max)
100V out 129
(42dB)
70V out 90
(39dB)
4ohm out 23
(27dB)
Output Regulation
95% (1kHz)
Dimensions
4.36" H x 19" W x 17" D
Weight
44lb
Shipping Weight
53lb
DIGIPAGE
Page 20 • September 2007
Zone Paging System
• Starts as an 8 x 8 system and can be expanded to a 16 x 16
• From 8 to 16 zones
• Remote paging stations
• Remote source & volume selection
• Extremely user friendly remote panels
• Extremely contractor friendly CAT 5 cable
DigiPage Base Station
• Each of the 8 zones has a dedicated local mic/line input
• 6 Mic/Line inputs routable to any of the 8 zones (or 16 when a
slave unit is added)
• 1 priority input which has total priority over all other inputs and is
activated by contact closure. The priority input has its own level
control.
• Alert, Evacuation, Bell and Pre Announce Chimes
• Priority Ducking Circuitry
• 4 CAT-5 ports which are used to connect to the remote zone
paging microphones and the remote source/volume selectors
which are daisy-chained on CAT-5 cable.
• Various levels of input and output level control
• Multi-stage volume status LEDs & easy input selection
• Separate paging volume level adjustment per zone
• Treble and Bass control per zone
Specifications are subject to change without notice.
SPECIFICATIONS
Data/Digital Audio Mic
RJ45 CAT5 Connector
Program Sources (Trim Max.)
Unbalanced (RCA): Input
Impedance:100KW;
Sensitivity:150mV
Balanced (XLR): Input
Impedance:1k3W;
Sensitivity:1mV
Min.Trim: -46dB
Local Source
Unbalanced (RCA): Input
Impedance:100KW;
Sensitivity: 1.5V
Balanced (XLR) MIC: Input
Impedance:1k3W;
Sensitivity:11mV
Balanced (XLR) LINE: Input
Impedance:45KW;
Sensitivity:350mV
Sum Input
Input Sensitivity:330mV;
Threshold: -46dBu
(at output, ind.of input)
Frequency Response (3dB)
15Hz - 17kHz
THD
0.005%
Noise
Page Mic: -84dB;
Other Inputs: -89dB
Power Supply 2
4VDC 30VA Plug-pack
Dimensions
5.2” H x 19.01” W x 6.7” D
Weight
13.2 lbs.
Shipping weight
15.4 lbs
DIGIPAGE JR
Page
21
September
2007
September
2007 • Page
21
Page
2007
Page
21
• September
September
2007
Page
2121
• ••September
2007
Zone Paging System
The DigiPage Jr is a matrix switching system allowing any one of up to 8 remote
paging microphones (DPJ88M) to page into any combination of up to 8 output
zones over industry standard CAT-5 cable. The system also allows any one of
up to 4 program inputs to be directed to any or all of the 8 output zones. An
emergency input is also provided.
The DigiPage Jr matrix is an attractive, slim-line, 2RU steel cabinet, desk or 19"
rack mounted. It includes inputs for each of the 8 remote DPJ88M microphone
stations (line level signal and control) and a line level output to each of the 8
output zones. Also included are inputs for the 4 program sources (CD, tape,
tuner etc) with associated level trim pots and an input for an emergency signal
such as from an EWIS control panel or priority message system. Alert and
evacuate signal tone generators are connected internally and may be activated
remotely by simple contact closure.
The DigiPage Jr allows for total control over the operation of each of the 8
output zones. Each of the 8 output zones is equipped with controls for program
selection, by means of 4 interlocking push buttons, with controls for microphone
level, program level, bass, treble and master output level. Each zone also has
an associated push button to allow any zone the option to be isolated from
receiving paging announcements.
The DigiPage Jr may be powered via AC mains 240 volts or DC, 12 - 24 volts.
(alternate voltages on special order)
Specifications are subject to change without notice.
SPECIFICATIONS
Data/Digital Audio Mic
RJ45 CAT5 Connector
Program Sources (Trim Max.)
Unbalanced (RCA): Input
Impedance:100KW;
Sensitivity:150mV
Balanced (XLR): Input
Impedance:1k3W;
Sensitivity:1mV -57dbu
Min.Trim: -46dB
Local Source
Unbalanced (RCA): Input
Impedance:100KW;
Sensitivity: 1.5V
Balanced (XLR) MIC: Input
Impedance:1k3W;
Sensitivity:11mV
Balanced (XLR) LINE: Input
Impedance:45KW;
Sensitivity:350mV
Sum Input
Input Sensitivity:330mV;
Threshold: -46dBu
(at output, ind.of input)
Frequency Response (3dB)
15Hz - 17kHz
THD
0.005%
Noise
Page Mic: -84dB;
Other Inputs: -89dB
Power Supply 2
4VDC 30VA Plug-pack
Dimensions (H x W x D)
5.2” H x 19.01” W x 6.7” D
Weight
9.9 lbs.
Shipping weight
12.2 lbs
ZM 3
Page 22 • September 2007
Zone Paging Mixer
Description
The Australian Monitor ZoneMix3 is an extremely versatile and innovative
mixer and signal router. Featuring a broadcast quality audio spec, the
ZoneMix3 allows selection of 4 stereo sources to 3 stereo zones either at the
ZoneMix3 or remotely. One stereo source can have selectable priority per
zone and each stereo zone boasts 5 stage equalization. The ZoneMix3 also
has the ability to route two independent mic or line signals to any zone or
combination of zones. Add to this remote volume controls in each zone and
the ZM3M 3 zone paging microphone (both running via inexpensive CAT-5
cabling) and you have an extremely high quality zone selecting mixer at a
fraction of the cost of other products in this market.
Inputs
There are two MIC/LINE inputs. The balanced XLR inputs accepts mic level
signals. The dual RCA inputs accept line level inputs and are summed to mono
internally. Gain and EQ are controlled from the front panel. These inputs
supply 15V phantom power, unless internally disabled. These inputs may have
priority over program inputs, if this feature is enabled.
There are four program inputs. These are stereo RCA line level inputs. Trim is
controlled from the front panel. LINE4 is a priority input, if this feature is
enabled.
PAGE INPUT: There is an RJ45 connector on the rear of the unit accepts a
CAT-5 cable from the optional ZM3M Paging Station.
SUM INPUT: This input has overall priority and is usually used for an
emergency tone or message.
Outputs
There are 3 Stereo Zone balanced XLR Outputs. The zone outputs are
configured as stereo left and right as default but can be internally changed to
mono.
Link
Two ZoneMix3 Units can be linked together to provide six stereo zone outputs.
Controls
There are various levels of control you can use to ensure the optimum result
from your ZoneMix3. They include: Trim Control for all inputs 5 Stage EQ on
each zone output Mic/Line Selection for the first two inputs Program Control for
selecting a program source via the front panel. This can also be done
remotely with the ZM3R Remote Source/Volume Selection Unit.
Specifications are subject to change without notice.
SPECIFICATIONS
Sensitivity (for 0dB out):
Mic/Line Input (RCA)
86mV (-19dB);
Mic/Line Input (XLR)
1.55mV (-54dB);
Prog Input (RCA)
190mV (-12dB)
Max Level Out:
10V RMS (+22dB)
Frequency Response:
20Hz - 20kHz
(0dB/-3dB)
THD:
Less than 0.1%
Noise:
-80dB
Crosstalk:
Better than 65dB
Phantom Power:
15VD
Metering and Status:
A “status” LED gives an
indication of OUTPUT
signal. It glows green
at 30dB and red at
0dBV(1V). This is meant
to indicate clip within the
ZoneMix3. When used
with Australian
MonitorSynergy
amplifiers, both LEDS on
the ZoneMix3 and the
Synergy amplifier will go
red simultaneously
indicating system clip
(with pot at full on the
amplifier).
A “remote” LED indicates
that the zone is in remote
control mode.
A “power” LED indicates
there is power to the unit.
Power Input:
20VAC; 30VA max.
Dimensions
1.74” H x 18.9” W x 11.2” D
Weight:
5.5lb
Shipping
6.6lb
ZM4
Page
23
September
2007
September
2007 • Page
23
Page
2007
Page
23
• September
September
2007
Page
2323
• ••September
2007
Zone Paging Mixer
• 6 universal inputs
• +/- 15dB gain trim per input
• 4 balanced outputs
• Input 1 has selectable priority
• Individual output assign with LED
• Switchable mic/line balanced XLR inputs indication per input
• Bi colour status LED per output
• Bi colour status LED per input
• Remote VCA volume control per output
• HPF & 15 VDC Phantom power
• On board Pre announce, bell, alert & evac tones switchable
per input
• 2 stage EQ per input
Featuring 6 inputs that can be balanced XLR mic or dual RCA/balanced
XLR line level, all available to any combination of 4 zone outputs.
Input one can be designated as a paging input with priority over all other
inputs individualy selectable at each zone output. Front panel switches
with LED indication provide for simple routing of each input. Each input
has bi colour status LED indication & 2 stage equalization. Each input
has an internal gain trim which can provide a further +/- 15dB of gain to
allow the perfect set up of input gain no matter what the input signal may
be. Phantom power & high pass filters are also supplied per input.
Each balanced XLR zone output also features a dual colour status LED &
switchable paging mic priority. Remote VCAs are also available for each
output allowing for a wall mounted volume control to be installed in
remote zones giving a volume range from off to whatever the master level
on the AMIS ZRM4 relevant zone output is set to. Alert, Evacuation, Bell
& Pre announce tones are also provided on board. The AMIS ZRM4 is a
compact yet extremely versatile zone routingmixer which makes the
complex task of multizone signal routing simple & cost effective.
Specifications are subject to change without notice.
SPECIFICATIONS
Sensitivity:
(input for 0dBu out)
RCA In -26dBu to
+4dBu (39mV
to 1.23 V)
XLR Line In -26dBu
to +4dBu
(39mV - 1.23V)
XLR Mic In -60dBu
to -30dBu (0.78mV
to 25mV)
Max Level In
>14.1 Vrms (+25dBu)
Max Level Out
>15.4 Vrms (+26dBu)
Frequency Response
<5Hz to >22kHz
(0dB/-3dB)
THD
Less than 0.1%
Noise
<90dBu 20Hz-20kHz
(all pots centered)
Crosstalk
<-65dB @ 1kHz
Phantom Power
15VDC
Power Input
20VAC; 600mA max or
24 to 34v DC regulated
600mA max
Dimensions
44.0h x 482.0w x 188.0d
Weight Net
6.4lb
Shipping
9.7lb
BGM2 Series
Page 24 • September 2007
Dual CD player / CD Player & Tuner /Dual Tuner
· 1 RU dual program source
· MP3 compatible CD player
· Option IR control for the CD player
· up to 20 tracks programmable on the CD player
· 10 user selectable presets on the AM/FM tuner
· Discrete stereo outputs for each module
· Priority stereo output as standard
· Tuner sleep function
The Australian Monitor Installation Series BGM2 program source series is
a one rack unit, dual program source positions that can be populated
witrh 2 CD players (BGM2-DCD), a CD player and an AM/FM tuner
(BGM2-TCD) or dual tuners (BGM2-DT). The tuner module has one FM
band and one AM band, with 10 user selectable preset stations, there is
also a programmable sleep function for the tuner. The CD/MP3 player is
fully programmable up to 20 tracks and includes Random track selection
for CDs and Repeat single track or Repeat all track functions for both CD
and MP3s. There is also an optional IR control available for the CD/MP3
player.
The BGM2 is supplied with an IEC power lead and AM/FM antenna (on
tuner models). The BGM2 has individual stereo outputs from both the
Tuner and CD player as well as a stereo priority output.
Specifications are subject to change without notice.
SPECIFICATIONS
CD/MP3 PLAYER
Output Level
@ 1kHz, 0dB 1.2V +/0.3V
Frequency Response
20Hz-20kHz +/- 2dB
Separation
1kHz, 0dB >60 dB
T.H.D+ Noise
1kHz, 0dB <0.05%
AM / FM TUNER
FM Tuning Range
87.5 MHz -108 MHz
IF Frequency & Rejection
10.7 MHz >80 dB
Image Rejection
>25 dB
S/N Ratio
1mV/M Input 46db
T.H.D
1mV <1.0%
Auto Tuning Sens.
<50uV
AM Tuning Range
522kHz – 1620kHz
IF Frequency & Rejection
450 kHz >45dB
Image Rejection
>30dB
S/N Ratio
5mV/M Input >35dB
Auto tuning sens.
<2mV
Dimensions
18.97” W x 1.73” H x 9.84” D
Weight 5kg
AMIS 215 EQ & 31EQ
Page
25
September
2007
September
2007 • Page
25
Page
2007
Page
25
• September
September
2007
Page
2525
• ••September
2007
2 Channel 15 Band Equalizer
The Australian Monitor Pro Series AMIS 215EQ is a single rack unit
graphic equalizer. Featuring constant Q circuitry, selectable 6dB or 12dB
slider range, balanced XLR, 6.35mm TRS & unbalanced RCA inputs &
outputs, EQ bypass switches, ground lift switches, output level controls &
overload LED’s.
Single Channel 31 Band Equalizer
The Australian Monitor Pro Series AMIS 31EQ is single rack unit graphic
equalizer. Featuring constant Q circuitry, selectable 6dB or 12dB slider
range, balanced XLR, 6.35mm TRS & unbalanced RCA inputs & outputs,
EQ bypass switches, ground lift switches, output level controls, overload
LED’s & variable high & low pass filters.
The features found in Australian Monitor Pro Series graphic EQ’s are
usually associated with equalizers many times the price of these. The
AMIS 215EQ and AMIS 31EQis an extremely well featured graphic
equalizer at a contractor friendly price.
Specifications are subject to change without notice.
EQUALIZER
AMIS215EQ - 2 x 15 2/3 Octave ISO
Spacing from 20Hz – 20kHz
AMIS31EQ - 31 1/3 Octave ISO
Spacing from 20Hz - 20kHz
Type Constant Q
Accuracy 3% Center Frequency
Travel 20mm Positive Centre Detent
Range +/- 6dB or +/- 12dB
selectable
2. INPUTS
Type Active balanced/unbalanced
Connectors 3 pin XLR, 6.35mm TRS
balanced, RCA unbalanced
Impedance 20k Ohms balanced, 15k
Ohms unbalanced
Max level +22dBm (level control at
centre)
3. OUTPUTS
Type Active balanced/unbalanced
Connectors 3 pin XLR, 6.35mm TRS
balanced, RCA unbalanced
Impedance <150 Ohms Typical
Max Level +22dbm (2k ohms)
+18dBm (600 ohms)
4. RFI FILTERS Yes
5. PASSIVE BYPASS SWITCHES
Yes
6. OVERLOAD LED SWITCHES
5dB below clipping
7. LOW CUT FILTER (AMIS31EQ
only) 10-250Hz, 12dB per octave
8. HIGH CUT FILTER (AMIS31EQ
only) 3kHz-40kHz, 12dB per octave
9. FREQUENCY RESPONSE 20Hz20kHz
10. IM DISTORTION (SMPTE)
0.005%
11. SIGNAL TO NOISE RATIO 94dB (20kHz noise bandwidth)
12. CHANNEL SEPARATION 50dB
13. COMMON MODE REJECTION
50:1
14. VOLTAGE 190-250VAC, 50Hz
15. DIMENSIONS* 1.75” H x 19.01”
W x 8.50 D
16. WEIGHT* 5.51lbs
AMIS 23x & CL2
Page 26 • September 2007
2 Way Crossover
SPECIFICATIONS
Frequency Range
X1 80Hz to 920 Hz
kHz
X2 800Hz to 9.2
Hum and Noise
>93dBu
Low Frequency Section
Output @ 0dB <-106 dBu
High Frequency Section
Output @ 0 dB <-97d dBu
The Australian Monitor Pro Series AMIS23X is a one rack unit, fourth
order Linkwitz-Riley electronic crossover. The AMIS23X can be
confi- gured as either a stereo two way or a mono three way
crossover. Featuring clip LED indication per band per channel,
frequency range selector switch, CD horn boost switch & polarity
reverse switching, the AMIS 23X is a professional price-performing
crossover.
Compressor - Limiter
The Australian Monitor Pro Series AMIS CL2 is a 1 RU, dual channel
compressor limiter. Featuring an expander/gate, compression & limiting
per channel, the AMISCL2 utilizes a high quality VCA to give excellent
performance from a budget priced dynamics processor. With added
features like selectable Automatic attack & release times & EQ
enhancement which automatically compensates for high end loss when
heavy compression is taking place, the AMISCL2 has the features & the
performance of a compressor/limiter many times the price.
Specifications are subject to change without notice.
Signal-To-Noise Ratio
118 dB
CONTROLS
Input Level Continuously
variable; Output Level
Low, High Cont. variable;
CD Boost Rear panel
switch; mute Front panel
switch; Channel link Rear
panel switch; Phase Rear
panel switch
Dimensions HxWxD
1.75” x 19” x 8.5”
Weight
5.5 lbs
SPECIFICATIONS
Input
Type RF-filtered, Servobalances input stage
Impedance 60K balanced
Nominal Operating Level 10dBu to 4dBu
Maximum Input Level
+21dBu balanced and
unbalanced
CMR
@ 1kHz >40dB
Input detection
Type DC de-coupled,
unbalanced input
Impedance >20K ohms
Maximum Input+21dBu
Output
Type Electronically
buffered output stage
Impedance <40 ohms
Bandwidth
5Hz to 50kHz, +0, -1dB
THD
@ +4dBu 0.05%typ..
IMD (SMPTE)
@ +10dBu 0.01% typ.
Noise & Hum
>93dBu
Crosstalk
@ 20kHz >85dBu
CONTRACTOR TOOLS
Page
27
September
2007
September
2007 • Page
27
Page
2007
Page
27
• September
September
2007
Page
2727
• ••September
2007
Multican (HA4 ) 4-Channel Headphone Amplifier The Australian
Monitor Installation Series HA4 is a high quality, low price 4channel
stereo headphone amplifier. Featuring a stereo 6.35mm jack input
& 4 stereo 6.35mm headphone jack outputs, the AMIS HA4 offers
separate volume controls per channel & a simple layout for ease of
operation. The AMIS HA4 is powered by a supplied 12VDC power
supply.
Juiced Up (PPA2 ) Dual Phantom Power Supply is an in-line
power supply that provides phantom power for 2 condenser mics.
Selectable between 12VDC & 48VDC, it will power nearly any
commercially available microphone. The AMIS PPA2 can run off 29
volt batteries or be powered by the supplied 12 VDC power supply.
Get Up 2 Way Stereo Converter converts consumer level signals
to professional level. Input will convert a pair of professional
balanced XLR signals to a consumer level stereo RCA signal. The
stereo path has its own volume control . The AMIS SC2 is powered
by a supplied 12 VDC power supply
Get Down 2 Way Stereo Converter converts professional level to
consumer level signals.
Let’s Split (MSC1) Microphone Splitter / Combiner produces 2
balanced XLR signals, (1 direct, 1 transformer isolated) from a
single balanced XLR input. The AMIS MCS1 provides a ground lift
switch to eliminate hum.
Let’s Split (LSC1) Line Splitter / Combiner produces 2 balanced
XLR signals, (1 direct, 1 transformer isolated) from a single
balanced XLR line level input. The AMIS LSC1 provides a ground
lift switch to eliminate hum.
Mixed Up (PM4 ) 4 Channel Passive Mixer is a 4 input, 1 output
passive mixer that can be used for mixing 4 mics, instruments, or
line sources or forconverting stereo feeds to mono. The AMIS PM4
requires no batteries or other external power source. The unit
features unbalanced 6.35mm jack inputs & outputs and can be
used as a 1 in 4 out signal splitter when all channel volumes are
run at maximum.
Specifications are subject to change without notice.
CONTRACTOR TOOLS
Page 28 • September 2007
Pre Me (PRE1 ) Mini Microphone Preamp features balanced XLR
& unbalanced 6.35mm jack inputs & outputs, switchable 36 volt
phantom power, gain control & signal clip LED. Powered by a
supplied 12VDC power supply,
Injector (DI1) Passive Direct Injection Box features a balanced
XLR output, a 6.35 mm TRS through output, 3 stage pad offering
up to 40dB of attenuation & a ground lift switch for hum
elimination.
Buzz Off (HE2) Dual Hum Eliminator tool for eliminating hum &
signal noise caused by ground loops. The AMIS HE2 has two
discreet signal paths via balanced XLR inputs & outputs. The
AMIS HE2 is a passive device & can also be used as a converter
of balanced & unbalanced signals. As part of the AMIS Contractor
Tools range, the AMIS HE2 is an inexpensive
Drop Me 70 volt to line level converter with phoenix to XLR and
level control.
AMIS26 2 x 6 Mic/Line Distribution Amplifier. 24VDC Phantom
Power switchable per input. Either input can be routed to any of
the 6 outputs via front panel dip switches
MP8 8 Channel Monitor Panel. 100/70V Line or Low Impedance
Applications. Includes 2.5 inch speaker with volume control.
Simply select any of 8 amplifier via the front panel switch and you
can monitor its output through the speaker and via an LED array.
Signal Present LED provided for each zone for easy
troubleshooting. Loop in, loop out terminal strips for inputs from
amplifiers and outputs to speakers.
Specifications are subject to change without notice.
MICROPHONES
Page 29 • September 2007
AV Essentials
AV 1
Continuously Variable pattern desktop boundary layer microphone
• Continuously variable pick-up pattern selector Potentiometer
• Programmable feather-touch membrane switch
• Selectable Push-To-Talk or Push-To-Mute
• Selectable power up ON or power up MUTED
• Selectable bass roll-off filter (12dB/oct @ 200Hz)
• Status LED
• Special energy absorbing shock mount compound on bottom
• Security control cover
• Available in white
AV Essentials
AV 2
RF Resistant Cardioid Desktop Boundary Microphones
• RF resistant design
• Unidirectional for rejection of feedback or unwanted ambient sounds
• Rugged, double layered, perforated steel screen
• Non slip rubber pad for shock isolation
• Key hole mounting slots for permanent installation
• Detachable 30' audio cable terminating in male 3-pin XLR type connector
• Available in white
AV Essentials
AV 3
RF Resistant Cardioid Condenser Mini-Boundary Microphones
• RF resistant design
• Low profile mounting in panels, table tops, walls or ceilings
• Hemi cardioid directional pick-up pattern
• Dual surface and bottom shock isolation bushings
• Low noise transformerless electronic design
• 13/16" (20mm) threaded diameter with mounting hardware
• Available in white
MICROPHONES
Page 30 • September 2007
Astatic GSM-1
Heavy-Duty Installation Shockmount
• Hi mass for maximum shock absorption
• No"sag" or "droop", even when using longer gooseneck microphones
Astatic 827A-13, 827A-17
Cardioid Mini Gooseneck Condenser Microphones
• Unidirectional for rejection of feedback or unwanted
ambient sounds
• Unique all flex gooseneck design for precise positioning
• Low noise transformerless electronic design
• Includes foam pop filter
Astatic 40-118
Hi Mass, Heavy-Duty Portable Desk Stand with LED
• Large, soft-Touch programmable membrane switch with LED
• LED Status indicator on electronically noiseless switch
• Selectable Push-To-Talk or Push-To-Mute (-55dB)
• Selectable power up ON or power up MUTED
Astatic AMC105SNO Series
Heavy duty omni directional paging microphone (one DPDT switch)
• Heavy-duty gooseneck and mounting flange
• High impact resistant Cycolac housing
• Broad rising frequency response tailored for speech
intelligibility and communication
• Switch wired normally open
• Low impedance
• Internal shock mount
Astatic AMC105SNO-2
Heavy duty Omnidirectional Paging Microphone (two DPDT switch)
• Omnidirectional
• Two switches for various paging and zone paging options
Astatic 611L
Dynamic Omni-directional Palm Held Microphone
• Rugged polyester mic element resists effects of extreme temperature, moisture, most acids, alkaline & solvents
• Low impedance for long canle runs and hum resistance
• Molded high impact resistant Cycolac body
• 75,000 cycle switch
• Permanently attached heavy duty, 4-conducter, 2-shielded, coiled chord with
stripped & tinned ends
• Included panel mount hanger-clip
Astatic 631L
Dynamic Noise Canceling Palm Held Microphone
• 360° elimination of background noise and resists feedback
• Soft curved lip guard to encourage proper spacing for best up-close use
• Other features same as 611L
Specifications are subject to change without notice.
In every system there are the primary core components like the projector, the codec, the audio
conference processor, etc.
AV Essentials is a collection of lines and a Starin line unto itself that provide the “glue” to the
system. From interfaces & switching to power conditioning, projection screens, playback sources,
assistive listening, mounting hardware, intercom, mirophones and more.
It is our aim at Starin to provide you with readily available support material for AV Essentials by
way of our RESELLER PORTALS. You will find resources to help understand the technical and
selling points of the products. There are mutli-media streaming training modules, FAQs, sales
tools, promotions, trouble escalation, warranty info, contacts and of course...pricing.
AL
TINEX
ALTINEX
APC
ELITE SCREENS
FEC RA
CK MOUNT
S
RACK
MOUNTS
GENTNER ALS
JV
C CONSUMER
JVC
KENA -VISION
KEN-A
KRAMER
NA
VIT
AR
NAVIT
VITAR
NIGEL B
OMNIMOUNT
TELEX INTER
COM
INTERCOM
www.Starin.biz
Enter your pasword into the Starin.biz home page
to click thru to portal links on the left column.
RESELLER PORTALS
Distributed exclusively in the U.S. by
Reseller Portal for Pricing, Programs and Product Details:
http://AustralianMonitor.Starin.biz
Represented by:
(IL, WI)
(OTHER AREAS)
Starin
136 Venturi Drive
Chesterton, IN 46304
PH: 800-846-5606
FX: 219-929-4377
www.starin.biz
(TX, OK, AR, LA)
Cowser Lee Marketing
6701 Mt. Vernon Ct.
Arlington, TX 76017
PH: 817-572-6433
FX: 817-478-5262
www.cowserleemarketing.com
Loft AV
1110 Scalon Drive D-1
Wheeling, IL 60090
PH: 847-520-9020
FX: 847-609-2221
www.loftav.com
(AL, GA, IN, KY, MS, NC, SC, TN)
Tech Rep
508 Cinnamon Place
Nashville, TN 37211
PH: 615-941-8461
FX: 615-941-8471
www.techrepmarketing.com
(FL)
NuWay Technologies
110 South Ridge Road
Andalusia, AL 36420
PH: 334-222-8950
FX: 334-222-4317
www.nu-waytech.com