Download Sharp 19J-M100 Service manual

21FL94
SERVICE MANUAL
S64T921FL94//
COLOR TELEVISION
Chassis No. GA-4
MODEL
21FL94
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 4
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 5
» SERVICE MODE .................................................................................................................................. 6
» ADJUSTMENT METHOD ................................................................................................................... 12
» WAVEFORMS ..................................................................................................................................... 25
» CHASSIS LAYOUT ............................................................................................................................. 26
» BLOCK DIAGRAM .............................................................................................................................. 27
» DESCRIPTION OF SCHEMATIC DIAGRAM ...................................................................................... 31
» SCHEMATIC DIAGRAMS ................................................................................................................... 32
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 36
» REPLACEMENT PARTS LIST ............................................................................................................40
» PACKING OF THE SET ...................................................................................................................... 46
ELECTRICAL SPECIFICATIONS
POWER INPUT ....................................... AC 110~220 V, 50/60 Hz
POWER RATING .................................................................... 90W
PICTURE SIZE .......................................... 1,239 cm2 (192sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS .................................................. QFP/UNI-B1 Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency ...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ........................................ 4.0 W(RMS) x 2pcs
SHARP CORPORATION
SPEAKER
SIZE ................................................................... 12 x 5 cm, 2pcs
VOICE COIL IMPEDANCE ............................. 16 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ..................................................... 75 ohm Unbalanced
TUNING RANGES
VHF-Channels ............................................................... 2 thru 13
UHF-Channels ............................................................ 14 thru 69
CATV Channels ........................................................... 1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
21FL94
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation.
The only potential source of X-ray in current solid
state TV receivers is the picture tube. However, the
picture tube does not emit measurable X-Ray
radiation, if the high voltage is as specified in the
"High Voltage Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem.
Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry.
6. W h e n t r o u b l e s h o o t i n g a n d t a k i n g t e s t
measurements on a receiver with excessive high
voltage, avoid being unnecessarily close to the
receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
21FL94
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
21FL94
LOCATION OF USER'S CONTROL
4
21FL94
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 3.15A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 110~220V
AC line voltage, with a strong air signal or a properly
tuned in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 28.7kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 110~220V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to P603 pin3 and make
sure that the voltmeter reads 20 ±1.1V.
5. Apply external 27V DC at P603 pin3 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between P603 pin1 and P603 pin2.
Now make sure that normal picture appears on the
screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
5
21FL94
SERVICE MODE
Service Mode Overview
1.
2.
3.
4.
5.
Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.
Service mode is cleared by entering SERVICE key command during service mode.
If key input port (SERVICE) input is LOW, then it is in service mode.
During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE is disabled.
Service mode can be switched to 4 modes as follows by key input MENU;
Adjustment mode
First mode of service mode when SERVICE key is
pressed.
Setting mode
Check mode
First mode of service mode when local key
CH-UP + VOL-DOWN is pressed after MCU reset.
Option mode
6. AFT processing is disabled during service mode. PLL setting data is set to fo data.
7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively
in service mode. Energy Save is off.
8. Sleep timer, View timer, on timer and off timer are inactivated in Service mode.
9. Sound is muting in service mode except at Adjustment Items V20, M01, M03, M04, M05, and M06.
6
21FL94
Adjustment Mode Items
No.
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
Item Name
SUB-PICTURE
SUB-TINT
SUB-COLOR
SUB-BRIGHT
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
IC
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
Register
CONTRAST
TINT
COLOR
BRIGHT
VIDEO-TONE
V-SHIFT
H-PHASE
RF-DELAY
V-SIZE
VIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
Range
0~127
0~127
0~127
0~255
0~63
0~7
0~31
0~127
0~63
0~63
0~255
0~255
0~255
Default
127
64
64
128
32
4
16
127
32
32
127
127
127
V14
V15
V16
V17
V18
V19
V20
V21
M01
M02
M03
M04
M05
M06
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
SCREEN CUT OFF
SUB-VOL
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
1 Chip
1 Chip
1 Chip
1 Chip
MICON
1 Chip
1 Chip
1 Chip
MTS
MTS
MTS
MTS
MTS
MTS
R-DRIVE
B-DRIVE
COLOR
BASEBAND-TINT
CC-POS
CUT OFF
A-ATT
H-VCO
ATT (MTS)
VCO (MTS)
FILTER (MTS)
WIDEBAND (MTS)
SPECTRAL (MTS)
VOL (MTS)
0~127
0~127
0~127
0~127
0~255
0~2
0~127
0~7
0~15
0~63
0~63
0~63
0~63
0~63
64
64
64
64
32
0
127
4
10
32
28
27
32
63
7
21FL94
Ë SELF ADJUSTMENT
H-VCO
1.
2.
3.
4.
5.
6.
7.
When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
H-FREE(1chip) is set to 1.
H-OUT is set by intelligent monitor output.
IM input is set as TIM input.
H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC
1.
2.
3.
4.
When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
AGC-OUT is set by intelligent monitor output.
IM input is set as AD input.
By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO
1.
2.
3.
4.
5.
6.
7.
When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
VIF-DEF(1chip) is set to 1.
AFC is set by intelligent monitor output.
IM input is set as AD input.
VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
8
21FL94
Setting Mode Items
No.
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
Item Name
VIDEO TONE -GAIN (TV)
VIDEO TONE -GAIN (AV)
VIDEO TONE -GAIN (S-AV)
VIDEO TONE -GAIN(YUV)
ABCL
BS
ABCL-G
SHP-AV
SHP-SAV
SHP-YUV
RGB-CLIP
E-SAVE
FAO-VOL
PIF-G
Y-DELAY(TV)
Y-DELAY(AV)
Y-DELAY(SAV)
Y-DELAY(YUV)
TINT-AV
TINT-SAV
COL-AV
COL-SAV
R-DRI(R2)
R-DRI( R)
R-DRI(B)
B-DRI(R2)
B-DRI( R)
B-DRI(B)
V-FREE
GAMMA
TRAP(TV)
TRAP(AV)
H-FREE
1W(TV)
1W(AV)
YLPF
BS-D
BS-C
SL(TV)
SL(AV)
SL(SAV)
SL(YUV)
AFC2
VD(TV)
VD(AV)
AS(TV)
AS(AV)
AS(SAV)
AS(YUV)
FBP(TV)
FBP(AV)
FBP(SAV)
FBP(YUV)
C.CLIP LEVEL
IC
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
OFFSET
OFFSET
OFFSET
1 Chips
OFFSET
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
Register
V-TONE
V-TONE
V-TONE
V-TONE
ABCL
BS-OFF
ABCL-G
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
EXTRGB-CLIP
CONTRAST(OFFSET)
A-ATT
VIF-GAIN
Y-DELAY
Y-DELAY
Y-DELAY
Y-DELAY
TINT(OFFSET)
TINT(OFFSET)
COLOR(OFFSET)
COLOR(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
V-FREE
GAMMA
TRAP-FINE
TRAP-FINE
H-FREE
V.WINDOW
V.WINDOW
YSW-LPF
BS-DISCHARGE
BS-CHARGE
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
AFC2-G
VSYNC-DET
VSYNC-DET
AUTO-SLICE
AUTO-SLICE
AUTO-SLICE
AUTO-SLICE
FBP VTH
FBP VTH
FBP VTH
FBP VTH
C.CLIP LEVEL
9
Range
0/1
0/1
0/1
0/1
0/1
0/1
0/1
-16~+16
-16~+16
-16~+16
0/1
0~63
0~127
0~7
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
0/1
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0~3
0~3
0~3
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
Default
0
0
0
0
0
0
0
0
0
0
0
30
120
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
21FL94
Setting Mode Items (Continued)
No.
F55
F56
F57
F58
F59
F60
F61
F62
F63
F64
F65
F66
F67
F68
F69
F70
Item Name
PSW
FAO-VOL
CP
CC LEVEL
OSD POS
OFFSET-ADJ-COL
OFFSET-ADJ-TINT
OFFSET-ADJ-TINT-YUV
TIMER4-LOW SPEED
TIMER4-HIGH SPEED
R-CUT-YUV
G-CUT-YUV
B-CUT-YUV
R-DRI-YUV
B-DRI-YUV
CLOCK-ADJ
IC
MTS
MTS
PLL
MICON
MICON
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
1 Chips
Register
PSW
VOL
CHARGE PUMP
CC LEVEL
OSD POS
COLOR
TINT
BASEBAND-TINT
TIMER4 VALUE
TIMER4 VALUE
R-CUT(OFFSET)
G-CUT(OFFSET)
B-CUT(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
10
Range
0/1
0~63
0/1
0/1
0/1
-32~+32
-32~+32
-32~+32
0~225
0~225
-63~+63
-63~+63
-63~+63
-63~+63
-63~+63
0~25
Default
0
60
0
0
0
0
0
0
50
125
0
0
0
0
0
25
21FL94
Option Mode Items
No
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
OPTION FUNCTION
DEMO
DOWNLOAD
V-CHIP
SPEAKER
FAO
P.PREF
UNIV+
VIEW TIMER
EZ-SETUP
PON-CH
FAV-COL
COMPONENT
AV
AV2
MTS
TONE-CTRL
AUTO-OFF
INIT-LANG
SETUP-FLAG
AV-FR
AV3/S-IN
COMB
AUTO-INPUT
CLOCK
LED
FLAT
BASS BOOST
DSE
SRS
WHITE-OUT
0
1
Without DEMO
With DEMO
Without V-CHIP OP
With V-CHIP OP
Without V-CHIP
With V-CHIP
Without SPEAKER
With SPEAKER
Without FAO
With FAO
Without P.REF
With P.REF
Without UNIV+
With UNIV+
Without VIEW TIMER
With VIEW TIMER
EZ-SETUP
AUTO PRESET
Without POWER-ON
With POWER-ON
FAV-COL
COL-TEMP
Without COMPONENT
With COMPONENT
Without AV
With AV
AV1 system
AV2 system
Without MTS
With MTS
Without S-ADJ
With S-ADJ
Without AUTO-OFF
With AUTO-OFF
ENGLISH
SPANISH
NO SET UP
AUTO SET UP
"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
Without AV3/S-IN
With AV3/S-IN
Without COMB
With COMB
Without AUTO-INPUT
With AUTO-INPUT
Without CLOCK
With CLOCK
SEMEX MODEL
SPC MODEL
Not FLAT MODEL
FLAT MODEL
Without BASS BOOST
With BASS BOOST
Without DSE
With DSE
Without SRS
With SRS
Without WHITE-OUT
With WHITE-OUT
Default Data
1
0
0
1
1
1
1
1
0
0
1
1
1
1
1
1
1
1
1
3
0
0
1
1
0
1
0
0
0
1
Check Mode
Micron mask version, software version and ROM correction function status are displayed in check mode.
11
21FL94
ADJUSTMENT METHOD
Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways
is short the main chassis JA301 and JA410
There is three stage of Service Mode data
First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F70
to go into third stage of service mode data, press MENU key
Third stage data from 001 ~ 030
Below is the contents of these data
First Stage
Data
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
V21
M01
M02
M03
M04
M05
M06
Service Mode
SUB-PICTURE
SUB-TINT
SUB-COLOR
SUB-BRIGHT
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
SCREEN CUT OFF
SUB-VOL
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
Function
CONTRAST
TINT
COLOR
BRIGHT
VIDEO-TONE
V-SHIFT
H-PHASE
RF-DELAY
V-SIZE
VIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-DRIVE
B-DRIVE
COLOR
BASEBAND-TINT
CC-POS
CUT OFF
A-ATT
H-VCO
ATT (MTS)
VCO (MTS)
FILTER (MTS)
WIDEBAND (MTS)
SPECTRAL (MTS)
VOL (MTS)
Auto Adjustment Item
1. H-VCO
2. RF-AGC
3. PIF-VCO
12
Range
0~127
0~127
0~127
0~255
0~63
0~7
0~31
0~127
0~63
0~63
0~255
0~255
0~255
0~127
0~127
0~127
0~127
0~255
0~2
0~127
0~7
0~15
0~63
0~63
0~63
0~63
0~63
Default Data
127
64
64
128
32
4
16
127
32
32
127
127
127
64
64
64
64
32
0
127
4
10
32
28
27
32
63
21FL94
Second Stage
Data
Service Mode
F01
VIDEO TONE -GAIN (TV)
F02
VIDEO TONE -GAIN (AV)
F03
VIDEO TONE -GAIN (S-AV)
F04
VIDEO TONE -GAIN(YUV)
F05
ABCL
F06
BS
F07
ABCL-G
F08
SHP-AV
F09
SHP-SAV
F10
SHP-YUV
F11
RGB-CLIP
F12
E-SAVE
F13
FAO-VOL
F14
PIF-G
F15
Y-DELAY(TV)
F16
Y-DELAY(AV)
F17
Y-DELAY(SAV)
F18
Y-DELAY(YUV)
F19
TINT-AV
F20
TINT-SAV
F21
COL-AV
F22
COL-SAV
F23
R-DRI(R2)
F24
R-DRI( R)
F25
R-DRI(B)
F26
B-DRI(R2)
F27
B-DRI( R)
F28
B-DRI(B)
F29
V-FREE
F30
GAMMA
F31
TRAP(TV)
F32
TRAP(AV)
F33
H-FREE
F34
1W(TV)
F35
1W(AV)
F36
YLPF
F37
BS-D
F38
BS-C
F39
SL(TV)
F40
SL(AV)
F41
SL(SAV)
F42
SL(YUV)
F43
AFC2
F44
VD(TV)
F45
VD(AV)
F46
AS(TV)
F47
AS(AV)
F48
AS(SAV)
F49
AS(YUV)
F50
FBP(TV)
F51
FBP(AV)
F52
FBP(SAV)
F53
FBP(YUV)
F54
C.CLIP LEVEL
F55
PSW
F56
FAO-VOL
Function
V-TONE
V-TONE
V-TONE
V-TONE
ABCL
BS-OFF
ABCL-G
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
EXTRGB-CLIP
CONTRAST(OFFSET)
A-ATT
VIF-GAIN
Y-DELAY
Y-DELAY
Y-DELAY
Y-DELAY
TINT(OFFSET)
TINT(OFFSET)
COLOR(OFFSET)
COLOR(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
V-FREE
GAMMA
TRAP-FINE
TRAP-FINE
H-FREE
V.WINDOW
V.WINDOW
YSW-LPF
BS-DISCHARGE
BS-CHARGE
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
AFC2-G
VSYNC-DET
VSYNC-DET
AUTO-SLICE
AUTO-SLICE
AUTO-SLICE
AUTO-SLICE
FBP VTH
FBP VTH
FBP VTH
FBP VTH
C.CLIP LEVEL
PSW
VOL
13
Range
0/1
0/1
0/1
0/1
0/1
0/1
0/1
-16~+16
-16~+16
-16~+16
0/1
0~63
0~127
0~7
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
0/1
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0~3
0~3
0~3
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0~63
Default Data
0
0
0
0
0
0
0
0
0
0
0
30
120
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
60
21FL94
Second Stage (Continued)
Data
F57
F58
F59
F60
F61
F62
F63
F64
F65
F66
F67
F68
F69
F70
Service Mode
CP
CC LEVEL
OSD POS
OFFSET-ADJ-COL
OFFSET-ADJ-TINT
OFFSET-ADJ-TINT-YUV
TIMER4-LOW SPEED
TIMER4-HIGH SPEED
R-CUT-YUV
G-CUT-YUV
B-CUT-YUV
R-DRI-YUV
B-DRI-YUV
CLOCK-ADJ
Third Stage
Data
OPTION FUNCTION
001
DEMO
002
DOWNLOAD
003
V-CHIP
004
SPEAKER
005
FAO
006
P.PREF
007
UNIV+
008
VIEW TIMER
009
EZ-SETUP
010
* PON-CH
011
FAV-COL
012
COMPONENT
013
AV
014
AV2
015
MTS
016
TONE-CTRL
017
AUTO-OFF
018
INIT-LANG
019
SETUP-FLAG
020
AV-FR
021
AV3/S-IN
022
COMB
023
AUTO-INPUT
024
CLOCK
025
LED
026
FLAT
027
BASS BOOST
028
DSE
029
SRS
030
WHITE-OUT
Function
CHARGE PUMP
CC LEVEL
OSD POS
COLOR
TINT
BASEBAND-TINT
TIMER4 VALUE
TIMER4 VALUE
R-CUT(OFFSET)
G-CUT(OFFSET)
B-CUT(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
Range
0/1
0/1
0/1
-32~+32
-32~+32
-32~+32
0~225
0~225
-63~+63
-63~+63
-63~+63
-63~+63
-63~+63
0~25
Default Data
0
0
0
0
0
0
50
125
0
0
0
0
0
25
DATA = "0"
DATA ="1"
DEMO DISABLE
ENABLE
V-CHIP OP DISABLE
ENABLE
V-CHIP DISABLE
ENABLE
SPEAKER DISABLE
ENABLE
FAO DISABLE
ENABLE
P.REF DISABLE
ENABLE
UNIV+ DISABLE
ENABLE
VIEW TIMER DISABLE
ENABLE
EZ-SETUP
AUTO PRESET
POWER-ON DISABLE
ENABLE
FAV-COL
COL-TEMP
COMPONENT DISABLE
ENABLE
AV DISABLE
ENABLE
AV1
AV2
MTS DISABLE
ENABLE
S-ADJ DISABLE
ENABLE
AUTO-OFF DISABLE
ENABLE
ENGLISH
SPANISH
NO SET UP
AUTO SET UP
"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
AV3/S-IN DISABLE
ENABLE
COMB DISABLE
ENABLE
AUTO-INPUT DISABLE
ENABLE
CLOCK DISABLE
ENABLE
SEMEX MODEL
SPC MODEL
FLAT DISABLE
ENABLE
BASS BOOST DISABLE
ENABLE
DSE DISABLE
ENABLE
SRS DISABLE
ENABLE
WHITE-OUT DISABLE
ENABLE
**POWER ON BY CH-UP/CH-DOWN KEY
14
Default Data
1
0
0
1
1
1
1
1
0
0
1
1
1
1
1
1
1
1
1
3
0
0
1
1
0
1
0
0
0
1
15
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
001
002
0
0
1
1
1
SYMBOL
DEF
21FL94
FUNCTION
21FL94
FUNCTION
1
AV3
1
AV2
1
MTS
1
1
0
A-IN CLOCK LED
023 024 025
1
AV
013 014 015
016 017 018
1
15-1
REVISED CONTENT,
1
1
0
0
FLAT BASS DSE
026 027 028
1
TONE AUTO LAN
011 → ”0”=FAV-COL
“1”=COL-TEMP
018 → “0”=ENGLISH “1”=SPANISH
019 → “0”=NO SET UP “1”=AUTO SETUP
025 → “0”=SEMEX SPEC “1”=SPC SPEC
0
022
COMB
021
0
1
1
012
COMP
011
FAV-COL
1
FAO P.PREF UNIV+ VIEW
010
020
0
PON-CH
0
SRS
029
1
0
WHITE
030
3
SETUP AV-FR
019
0
EZ
007 008 009
REFER AS BELOW
“0”=DISABLE “1”=ENABLE
009 → “0”=EZ-SETUP “1”=AUTO PRESET
1
SP
003 004 005 006
DEMO DOWNLOAD V-CHIP
BUS OPTION FOR THIRD STAGE SERVICE DATA
DEF
21FL94
FUNCTION
BUS OPTION FOR THIRD STAGE SERVICE DATA
OSD CHECKING
OUTPUT
–
CONTENT
21FL94
–
PRE-ADJUST
REQUIREMENT
INPUT
CONDITION
–
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
REFER AS BELOW
OPTION SET UP
ADJUSTMENT
ITEM
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
REFER AS BELOW
V05 F15
F16
F19
F21 F23 F24
F25 F26 F27 F28
5
GAMMA 1W(AV)
50
SL(TV)
2
4
+8
+3
-2
C-OF
-18 -8
SL(AV) VD(TV) AS(TV) AS(AV) FAO-VOL CP
-7
TINT-OF
+6
SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV R-D(R2) R-D(R) R-D(B) B-D(R2) B-D(R) B-D(B)
SYMBOL
DEF
21FL94
FUNCTION
21FL94
1
F67
1
+36
+2
1
15-2
REVISED CONTENT,
-12
TI-YUV G-C-YUV B-C-YUV
F62 F66
1
1
1
1
58
1
+10 +8
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
F30 F35 F39 F40 F44 F46 F47 F56 F57 F60 F61
FUNCTION
DEF
21FL94
FUNCTION
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
OSD CHECKING
OUTPUT
–
CONTENT
21FL94
–
PRE-ADJUST
REQUIREMENT
INPUT
CONDITION
–
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
REFER AS BELOW
BUS SET UP
ADJUSTMENT
ITEM
21FL94
US 4 CH LION HEAD (MONOSCOPE)
AC 220V, US MAGNETIC FIELD
CONFIRMATION BY CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
16
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, CRT-PURITY
PRE-ADJUST
REQUIREMENT
0-31
AC 220V
CONFIRMATION BY CRT SCREEN
INPUT
CONDITION
OUTPUT
16-1
HISTORY
OF REVISION
16-2
REVISED CONTENT,
SYMBOL
REVISED CONTENT,
SYMBOL
ADJUSTMENT
PROCEDURE
US 4 CH LION HEAD
CONTENT
[CHECKING SPEC]
OVERSCAN 10 ± 2.5%
B
OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST
PRE-ADJUST
REQUIREMENT
ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS
SPECIFIED BELOW.
CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE
ADJUSTMENT.
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V09
V-SIZE
ADJUSTMENT
ITEM
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
A
1. ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO SPEC
OF A=B.
2. IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT
B SLIDELY SMALLER THAN A
I2C BUS CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V07
H-POSITION
ADJUSTMENT
ITEM
21FL94
US 4 CH LION HEAD (MONOSCOPE PATTERN)
220V, RF INPUT, ZERO MAGNETIC FIELD
CONFIRMATION ON CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
17
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, CRT-PURITY
PRE-ADJUST
REQUIREMENT
0-7
US 4 CH LION HEAD
AC 220V
CONFIRMATION ON CRT DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
17-1
HISTORY
OF REVISION
17-2
REVISED CONTENT,
SYMBOL
REVISED CONTENT,
SYMBOL
A
TEXT BOX BLK
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
0~255
B
1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED.
2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO
SPEC OF A=B.
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V18
CLOSED CAPTION SET UP
ADJUSTMENT
ITEM
[CHECKING CONFIRMATION]
ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL POSITION.
THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL
POSITION
NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD
ENOUGH
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V06
V-PHASE
ADJUSTMENT
ITEM
21FL94
NO SIGNAL (RASTER) CONDITION
AC 220V
IC 801 PIN 11
CONTENT
INPUT
CONDITION
OUTPUT
18
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
0-7
SYMBOL
18-1
REVISED CONTENT,
[CHECKING SPEC]
FREQ = 15.735 ± 0.2 KHz
(SELF ADJ)
1) GO TO SERVICE MODE,BY SELECTING THE SERVICE DATA V21
2) PRESS THE R/C TO OPERATE AUTO H-VCO,OSD APPEAR "OK" AT
SCREEN
3) IF APPEAR "NG" PLS REPEAT STEP2
(MANUAL ADJ)
1) GO TO SERVICE MODE,
2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V21
H-VCO
ADJUSTMENT
ITEM
NO SIGNAL (RASTER) CONDITION
AC 220V
CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).
CONTENT
INPUT
CONDITION
OUTPUT
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
SYMBOL
18-2
REVISED CONTENT,
[CHECKING SPEC]
2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)
(AT MANUAL ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 2 VOLTAGE BECOME
AS SPECIFIED BELOW
(AT SELF ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT
SCREEN
3) IF APPEAR “NG” PLS REPEAT STEP2
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V10
PIF-VCO
ADJUSTMENT
ITEM
21FL94
TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION
OUTPUT
19
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
INPUT
CONDITION
RF INPUT
FIELD STRENGTH 53dBµV (FIX)
INPUT
CONDITION
19-1
19-2
REVISED CONTENT,
SYMBOL
HISTORY
OF REVISION
SYMBOL
REVISED CONTENT,
0-255
1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO
64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR
IN CUT-OFF CONDITION
2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW
BRIGHT, THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR
IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=RCUTOFF, V12=G-CUTOFF, V13=B-CUT-OFF, FIX THE DATA OF THE
COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE
OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BECOME WHITE.
3) TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE YMUTE SO THAT PICTURE APPEAR IN NORMAL MODE.
CONFIRMATION ON CRT DISPLAY
220V
WINDOW PATTERN OR US4CH LION HEAD
[VOLTAGE CONFIRMATION]
ADJUSTMENT
PROCEDURE
OUTPUT
SCREEN
STEP RANGE
OPTION SET UP, BUS SET UP
I2C CONTROL
V11,V12,V13
[VOLTAGE CONFIRMATION]
MAX - 0.1V dc
(AT MANUAL ADJUSTMENT MODE)
1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BECOME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE.
2. CHANGE THE ANTENNA INPUT SIGNAL TO 63-67 dBµV, AND MAKE
SURE THERE IS NO NOISE
3. CHANGE THE ANTENNA INPUT SIGNAL TO 90-95 dBµV TO BE SURE
THAT THERE IS NO CROSS MODULATION BEAT.
(AT SELF ADJUSTMENT MODE)
1. GO TO SERVICE MODE
2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC
KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN.
3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN.
CONTENT
US10CH HALF COLOR BAR
CONTENT
PRE-ADJUST
REQUIREMENT
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
I2C CONTROL
0-127
ADJUSTMENT
ITEM
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V08
RF-AGC
ADJUSTMENT
ITEM
21FL94
23CH 501RE WINDOW PATTERN
220V
CRT SCREEN DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
20
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN
PRE-ADJUST
REQUIREMENT
0-127, 0~255
SYMBOL
20-1
REVISED CONTENT,
[CHECKING CONFIRMATION]
X=0.273, Y=0.280 (11,600°K + 1 MPCD)
WHITE
US14
BLACK
1) WHITE (HIGH BEAM)
FIRST LET THE GUN POINT AT BLACK POSITION (AS DRAWING
ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN
LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH),
ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST
THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS
OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280
2) BLACK (LOW BEAM)
LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED
AWAY FROM THE DATA ADJUSTED IN STEP 1), ADJUST AGAIN THE
TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST
SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE.
*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING
THIS ADJUSTMENT.
**REPEAT STEP 1), 2) TO GET A REGULATED POSITION.
I2C BUS CONTROL
STEP RANGE
WHITE BALANCE
CONTROL
ADJUSTMENT
V14,V15,V11,V12,V13
POSITION
ADJUSTMENT
ITEM
STEP RANGE
SUB-BRIGHT
0-255
US14
20-2
REVISED CONTENT,
[VOLTAGE CONFIRMATION]
BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
BLACK
1) LET THE GUN POINT AT BLACK POSITION (AS ATTACH DRAWING),
ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN
STEP DOWN MORE 4 STEP
CRT SCREEN DISPLAY.
220V
WINDOW PATTERN
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
I2C CONTROL
V04
SYMBOL
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
21FL94
WINDOW PATTERN
220V
CRT SCREEN DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
21
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS
PRE-ADJUST
REQUIREMENT
220V
B-AMP TR BASE (TP853)
CONFIRRM WITH OSCILLOSCOPE
INPUT
CONDITION
OUTPUT
21-1
21-2
REVISED CONTENT,
SYMBOL
HISTORY
OF REVISION
SYMBOL
REVISED CONTENT,
[CONFIRMATION]
US14
US 10 CH HALF COLOR BAR PATTERN
CONTENT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST
REQUIREMENT
0-127
B-AMP BASE (TP853)
MUST BE IN STEPPING
LEVEL
1) GET IN Y-MUTE FUNCTION BY R/C.
2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.
3) DISABLE THE Y-MUTE
**PLS TAKE NOTE THAT SERVICE MODE DATA F61 NEED TO SET +8
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V02
SUB-TINT
ADJUSTMENT
ITEM
[VOLTAGER CONFIRMATION]
BRIGHTNESS Y=150 cd/m2
WHITE
1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING),
ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=150 cd/m2.
NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH
THE SPEC
I2C BUS CONTROL
0-127
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V01
SUB-PICTURE
ADJUSTMENT
ITEM
21FL94
R-AMP TR BASE (TP851)
CONFIRRM WITH OSCILLOSCOPE
OUTPUT
22
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OUTPUT
220V
INPUT
CONDITION
Y
SYMBOL
22-1
REVISED CONTENT,
[CHECKING CONFIRMATION]
W
G
100% WHITE
Cy
Mg
R
B
*PLEASE TAKE NOTE THAT SERVICE DATA F60 MUST SET TO +10
1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW
2) THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS
OF COLOR BAR BEAT AT THE SAME LEVEL
INPUT
CONDITION
US 10 CH HALF COLOR BAR PATTERN
CONTENT
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
CONTENT
PRE-ADJUST
REQUIREMENT
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TNT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
I2C BUS CONTROL
0-127
ADJUSTMENT
ITEM
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V03
SUB-COLOR
ADJUSTMENT
ITEM
–
STEP RANGE
–
22-2
REVISED CONTENT,
27V
26± 1.1V DC
SYMBOL
OPERATION VOLTAGE
TP VOLTAGE
[VOLTAGE CONFIRMATION]
[CAUTION]
FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC
CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUGGING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN
RESET.)
[RECOVER INFORMATION]
PULL OUT THE AC CORD.
[OPERATION CONFIRMATION]
SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PROTECTOR IS FUNCTIONED.
HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.
[VOLTAGE CONFIRMATION]
CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.
SET THE USER CONTROL TO SHIPMENT POSITION.
CONFIRMATION BY THE CRT
AC 220V, RF INPUT
US 4 CH LION HEAD (MONOSCOPE PATTERN)
AFTER ALL ADJUSTMENT FINISHED.
–
X-RAY PROTECTION OPERATING CONFIRMATION
21FL94
AC 220V, RF INPUT
CRT ANODE VOLTAGE
INPUT
CONDITION
OUTPUTΩ
23
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
–
SYMBOL
23-1
REVISED CONTENT,
[CAUTION POINT]
USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/
DHHS STANDARD TO MAKE CORRECTION AND CONTROL.
BELOW 30kV
HIGH VOLTAGE
SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH
ON Y-MUTE BY R/C CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH
VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.
AFTER ALL ADJUSTMENT FINISHED.
–
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
–
HIGH VOLTAGE
ADJUSTMENT
ITEM
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
STEP RANGE
0~15
SYMBOL
23-2
REVISED CONTENT,
[CHECKING SPEC]
490 ± 10mVrms (CHECKING SPEC :490 ± 20mVrms)
1) SET THE SOUND VOLUME CONTROL MORE THAN 1.
2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BECOME AS SPECIFIED BELOW.
IC 3001 39 PIN
AC 220V, RF INPUT
MONORAL SIGNAL (400HZ 100% MODULATION)
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
I2C BUS CONTROL
M01
MS LEVEL ADJUSTMENT
21FL94
STEREO SIGNAL SIGNAL 1,: MODULATION 30%, L-CH ONLY, NR-ON, 300Hz
SIGNAL 2,: MODULATION 30%, L-CH ONLY, NR-ON, 3kHz
RF INPUT
IC 3001 39 PIN
CONTENT
INPUT
CONDITION
OUTPUT
24
HISTORY
OF REVISION
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO, FILTER
PRE-ADJUST
REQUIREMENT
SYMBOL
24-1
REVISED CONTENT,
[CHECKING SPEC]
OVER 25 dB (CHECKING SPEC : OVER 20 dB)
SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE
READING FROM THE SPEAKER TERMINAL MUST BE OVER THE SPEC
AS SPECIFIED BELOW.
1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNTIL THE OF 39 PIN
BECOME MINIMUM LEVEL.
2) INPUT SIGNAL 2, ADJUST BUS DATA OF M05 UNTIL THE AC VOLTAGE OF 39 PIN BECOME MINIMUM LEVEL.
3) REPEAT STEP 1) AND 2).
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M04, M05
SEPARTION ADJUSTMENT
ADJUSTMENT
ITEM
24-2
21FL94
21FL94
WAVEFORMS
25
21FL94
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
1
2
3
4
26
5
6
21FL94
CRT BLOCK DIAGRAM
H
G
F
E
D
C
B
A
1
2
3
4
27
5
6
21FL94
MAIN BLOCK DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
28
7
8
9
10
21FL94
10
11
12
13
14
15
29
16
17
18
19
21FL94
MTS BLOCK DIAGRAM
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
30
7
8
9
10
21FL94
DESCRIPTION OF SCHEMATIC DIAGRAM
WAVEFORM MEASUREMENT CONDITIONS:
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
å AND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
ç MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES åET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
31
21FL94
SCHEMATIC DIAGRAM: MAIN Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
32
7
8
9
10
21FL94
10
11
12
13
14
15
33
16
17
18
19
21FL94
SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
1
2
3
4
34
5
6
21FL94
SCHEMATIC DIAGRAM: MTS Unit
H
G
F
E
D
C
B
A
1
2
3
4
35
5
6
21FL94
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
1
2
3
4
36
5
6
21FL94
H
RJ 1 4
RJ 1 5
B1
R1 0 2 7
R1 0 2 4
R3 8 4
R3 8 3
R1 0 0 3
R1 0 0 2
R3 8 2
C1 0 1 6
R3 8 1
R1 0 0 9
R1 0 0 8
R1 0 0 6
RJ 1 7
RJ 1 6
R1 0 0 7
RJ 8
F DC1
R1 0 8 3
Z1
A1
Q1 0 7 2
R1 0 5 6
R1 0 7 9
Q1 0 7 0
Q1 0 0 2
R1 0 8 5
G
R3 0 0 6
R1 0 7 8
R1 0 8 7
RJ 2 4
I C3 0 0 2
R3 1 4
R3 0 0 9
C3 0 8 1
C3 1 3
R3 1 5
RJ 2 3
R8 2 7
R1 8 4 9
R3 0 5
R8 2 1
Q8 0 5
C3 0 8
R3 0 7
RJ 4
R3 0 3
R3 0 8
RJ 2 6
R1 8 5 0
R8 3 1
Q1 0 7 3
R8 3 9
R1 8 9 5
R1 8 9 6
C8 4 5
R8 3 5
F
C8 4 6
R8 2 8
R7 1 4
R1 0 8 1
R7 0 9
C8 0 4
F DC3
R8 0 2
Q7 0 2
D8 0 1
R8 4 3
D8 1 0
C8 3 9
R8 3 3
C8 4 7
C8 0 2
C8 0 8
Q7 0 1
RJ 1 3
C8 0 6
R8 0 3
R8 0 4
R8 4 0
C8 4 1
R7 0 7
C1 8 6 7
C8 0 9
R8 0 5
D8 1 1
R1 8 5 1
R1 8 5 2
C8 3 6
R8 0 6
D8 1 2
R1 8 5 3
R1 8 0 2
RJ 3
I C8 0 1
C8 1 0
RJ 2 9
R8 0 7
C8 5 3
R6 6 2
RJ 3 0
R8 4 5
RJ 2 5
C8 3 2
R8 5 3
Q6 0 4
C8 3 3
C8 3 1
C8 1 4
E
C8 1 6
C8 1 5
R1 0 6 2
R8 4 2
R8 4 7
R1 0 6 3
R8 4 4
C8 3 0
R8 1 2
C8 1 9
C8 2 8
R1 8 5 4
R8 1 6
Q8 0 4
R8 1 4
C1 8 5 6
C8 2 1
R8 0 1
R8 3 2
R8 1 5
R8 1 7
C8 2 3
Q8 0 1
C8 2 6
C1 0 0 9
RJ 3 2
C1 0 1 1
R1 0 6 1
RJ 3 1
C1 0 1 3
C1 0 0 8
R1 0 6 5
R1 0 6 4
C1 8 5 5
D1 0 8 6
R1 0 5 5
R1 0 4 9
R1 0 4 8
R1 0 4 7
D1 0 8 9
D1 0 8 5
R1 0 4 6
D
I C1 0 0 1
R1 0 6 6
R1 0 7 7
R1 0 5 9
C1 0 1 5
R1 0 7 2
R1 0 9 6
R1 0 4 4
R1 0 3 7
R5 2 8
R1 0 3 6
R1 0 7 6
R1 0 3 4
R1 0 3 3
R1 0 9 0
R1 0 9 1
R3 0 1
R1 0 4 3
Q1 0 0 1
R1 0 7 4
R1 0 3 2
R1 0 3 8
R4 4 1
RJ 1 1
R1 0 3 9
C1 8 6 4
C1 8 6 2
C1 0 0 4
I C1 0 0 7
C1 8 9 6
R1 8 6 7
R1 0 4 1
R1 0 9 7
RJ 1 0
I C1 0 0 3
R2 1 3
C5 1 9
RJ 2 0
RJ 5
R5 2 0
Q2 0 2
R4 3 9
C5 1 8
R1 0 9 8
RJ 1 2
R5 0 4
C1 8 6 1
R2 2 0
R2 0 6
RJ 1 8
C1 8 6 3
Q2 0 1
C2 0 8
C2 1 0
C2 0 9
R2 1 1
R2 0 7
R2 1 0
RJ 2 2
R2 0 9
R2 0 8
C2 0 7
R2 0 5
C2 0 5
R4 3 7
R4 4 0
RJ 7
R2 1 2
C2 1 3
C2 1 2
RJ 2 7
R8 4 6
C
I C4 0 3
C4 0 1
R8 3 0
D2 0 2
RJ 2 8
RJ 1 9
C4 3 6
RJ 2
I C4 0 1
Q8 0 3
RJ 9
C2 0 3
R4 3 1
R4 3 2
Z2
R3 7 2
R3 7 7
R3 5 3
R3 7 3
R3 7 4
RJ 6
R4 6 2
I C4 0 2
R2 0 1
A2
I C3 0 5
R3 7 8
R2 0 2
R4 3 8
R3 6 5
R6 2 4
R6 1 7
RJ 1
C4 3 9
RJ 2 1
R3 6 6
R3 6 2
R3 6 3
R6 2 6
Z3
R1 8 6 1
F DC2
R4 3 5
R1 8 6 2
R6 1 8
R6 2 3
R4 3 3
R4 3 4
R4 6 1
C4 5 3
R4 5 8
R6 1 3
B
PWB-A: MAIN Unit (Chip Parts Side)
A
1
2
3
4
37
5
6
21FL94
H
G
F
E
D
C
PWB-B: CRT Unit (Wiring Side)
B
A
1
2
3
4
38
5
6
21FL94
H
G
F
E
PWB-C: MTS Unit (Wiring Side)
D
R3 0 0 4
R3 0 0 3
R3 0 2 5
C3 0 4 3
C3 0 0 2
Q3 0 0 4
R3 0 3 5
R3 0 0 5
R3 0 3 0
Q3 0 0 1
R3 0 2 9
R3 0 3 4
R3 0 2 8
Q3 0 0 2
R3 0 3 2
R3 0 2 6
R3 0 2 1
R3 0 2 7
Q3 0 0 5
R3 0 3 1
I C3 0 0 1
C3 0 4 2
R3 0 8 4
R3 0 8 5
C3 0 3 1
C3 0 2 6
R3 0 8 3
R3 0 1 6
C3 0 3 2
C3 0 2 8
C3 0 2 7
C3 0 1 3
R3 0 0 7
C3 0 3 6
R3 0 1 1
C3 0 2 4
C3 0 2 3
R3 0 1 3
C3 0 3 5
RJ 1 0 1
R3 0 1 0
R3 0 1 7
R3 0 1 5
R3 0 0 8
R3 0 1 2
R3 0 3 6
R3 0 3 3
B
C3 0 2 5
C3 0 3 3
R3 0 1 4
Q3 0 0 6
R3 0 1 9
Q3 0 0 7
A
PWB-C: MTS Unit (Chip Parts Side)
1
2
3
4
39
5
6
R3 0 0 2
C3 0 0 8
R3 0 8 2
R3 0 1 8
R3 0 0 1
C
21FL94
Ref. No.
Part No.
★
Description
Code
REPLACEMENT
PARTS
LIST
Ref. No.
Q604
Q751
Q752
Q753
Q754
Q801
Q804
Q805
Q1001
Q1002
Q1073
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics
are identified in this manual; electrical components having such
features are identified by "å" in the Replacement Parts Lists.
The use of a substitute replacement part which does not have the
same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or
other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
MARK
Ref. No.
2. REF. NO.
4. DESCRIPTION
: SPARE PARTS-DELIVERY SECTION.
★
Part No.
Description
Code
PICTURE TUBE
å L706
RCiLG0069PEZZ
X Degaussing Coil
VB51QDK191X1E X Picture Tube
QEARCA012WJZZ X Grounding Strap
AH
BV
AC
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
PWB-A DUNTKC522WEA0 - MAIN Unit
PWB-B DUNTKA599WED5 - CRT Unit
PWB-C DUNTKC574WEA0 - MTS Unit
—
—
—
DUNTKC522WEA0
PWB-A MAIN UNIT
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY NOT INDEPENDENTLY.
å TU201 VTUVT1T5UF202 X VHF Tuner
AP
INTEGRATED CIRCUITS
å
å
å
å
IC301
IC401
IC402
IC501
IC601
IC701
IC702
IC703
IC801
IC1001
IC1003
VHiAN17820B-1
VHiMM1501XN-1Y
VHiMM1501XN-1Y
VHiSTV9302A-1
VHiKA78R09AP1
VHiSTRW6753-1
RH-FXA003WJZZ
VHiSE125N++-F
VHiM61251CF1EQ
RH-iXA983WJZZ
VHiBR24L04F-1Y
Q201
Q601
Q602
Q603
VS2SC2735//1EY
VS2SC2235Y/1E+
VSTT2140+++-F
VS2SC3198-G-1+
X
X
X
X
X
X
X
X
X
X
X
AN17820B
MM1501XN
MM1501XN
STV9302A
KA78R09AP
STRW6753
FXA003WJ
SE125N++
M61251CF1
IXA983WJ
BR24L04F
AG
AC
AC
AD
AC
AG
AB
AD
AN
AK
D201
D203
D392
D502
D503
D505
D510
D601
D602
D603
D606
å D701
D702
D703
D704
D705
D706
D707
D708
D710
D714
D716
D751
D752
D801
D802
D803
D806
D810
D811
D812
D1001
D1081
D1085
D1086
D1089
D1091
D1094
D1095
D1801
VA701
RH-EX0676GEZZY
VHD1SS119//-1Y
RH-DX0452CEZZ
RH-EX0652GEZZY
RH-EX0612GEZZY
RH-DX0441CEZZY
RH-DX0131CEZZY
VHD1SS119//-1Y
VHD1SS244//-1Y
RH-EX0667GEZZY
RH-DX0131CEZZY
RH-DX0476CEZZ
RH-DX0490CEZZY
VHD1SS119//-1Y
RH-EX0650GEZZY
RH-DX0066GEZZY
RH-DX0066GEZZY
RH-DX0066GEZZY
RH-EX0621GEZZY
VHD1SS119//-1Y
VHD1SS119//-1Y
RH-EX0601GEZZY
RH-DXA006WJZZ
RH-DX0247CEZZ
RH-EX1393CEZZY
RH-EX0630GEZZY
VHD1SS119//-1Y
VHD1SS119//-1Y
RH-EX0263TAZZY
RH-EX0263TAZZY
RH-EX0263TAZZY
RH-PX0013PEZZ
VHD1SS119//-1Y
RH-EX1393CEZZY
RH-EX1393CEZZY
RH-EX1393CEZZY
VHD1SS119//-1Y
VHD1SS119//-1Y
VHD1SS119//-1Y
VHD1SS119//-1Y
RH-VX0073CEZZ
å PR701
å R751
å R752
X801
RMPTP0001PEZZ
RR-DZ0049CEZZY
RR-DZ0049CEZZY
RCRSAA009WJZZ
2SC2735
2SC2235Y
TT2140+++
2SC3198-G
X
X
X
X
X
X
X
X
X
X
X
2SD601AR
2SD468-C
2SD468-C
2SC3198-G
2SD468-C
2SD601AR
2SB709AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
Code
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Zener, EX0676GE
1SS119
DX0452CE
Zener, EX0652GE
Zener, EX0612GE
DX0441CE
DX0131CE
1SS119
1SS244
Zener, EX0667GE
DX0131CE
DX0476CE
DX0490CE
1SS119
Zener, EX0650GE
DX0066GE
DX0066GE
DX0066GE
Zener, EX0621GE
1SS119
1SS119
Zener, EX0601GE
DXA006WJ
DX0247CE
Zener, EX1393CE
Zener, EX0630GE
1SS119
1SS119
Zener, EX0263TA
Zener, EX0263TA
Zener, EX0263TA
PhotoDiode
1SS119
Zener, EX1393CE
Zener, EX1393CE
Zener, EX1393CE
1SS119
1SS119
1SS119
1SS119
Varistor
AB
AA
AB
AB
AB
AB
AA
AB
AB
AC
AB
AA
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AA
AB
AB
AB
AA
AA
AA
AA
AB
PACKAGED CIRCUITS
X
X
X
X
Packaged Circuit
Resistor
Resistor
Crystal, CRSAA009WJ
AE
AB
AB
AC
FILTERS
CF201
CF802
SF201
RFiLC0447CEZZ
RFiLC0446CEZZ
RFiLC0405CEZZ
X Filter, FiLC0447CE
X Filter, FiLC0446CE
X Filter, FiLC0405CE
L202
L203
L204
L602
L701
L751
L801
VP-CF270K0000Y
VP-DF270K0000Y
VP-XF1R2K0000Y
RCiLP0223CEZZ
RCiLFA060WJZZ
RCiLP0179CEZZ+
VP-DF100K0000Y
AB
AB
AD
COILS
TRANSISTORS
X
X
X
X
VS2SD601AR/-1Y
VS2SD468-C/-1+
VS2SD468-C/-1+
VS2SC3198-G-1+
VS2SD468-C/-1+
VS2SD601AR/-1Y
VS2SB709AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
Description
DIODES AND LED
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER
3. PART NO.
★
Part No.
AB
AD
AB
40
X
X
X
X
X
X
X
Peaking, 27µH
Peaking, 27µH
Peaking, 1.2µH
Coil, 3.3µH
Coil, CiLFA060WJ
Coil, CiLP0179CE
Peaking, 10µH
AB
AB
AB
AB
AD
AB
AB
21FL94
Ref. No.
Part No.
★
L802
L803
L804
L806
L807
L1861
L1862
VP-DF100K0000Y
VP-DF100K0000Y
VP-XF150K0000Y
VP-DF100K0000Y
VP-XF1R2K0000Y
VP-XF8R2K0000Y
VP-XF8R2K0000Y
X
X
X
X
X
X
X
Description
Peaking, 10µH
Peaking, 10µH
Peaking, 15µH
Peaking, 10µH
Peaking, 1.2µH
Peaking, 8.2µH
Peaking, 8.2µH
Code
AB
AB
AB
AB
AB
AB
AB
TRANSFORMERS
å T602
å T603
å T701
RTRNFA095WJZZ X Transformer
RTRNZA058WJZZ X Transformer
RTRNWA137WJZZ X Transformer
AR
AB
CAPACITORS
C201
C202
C203
C205
C206
C207
C208
C209
C210
C213
C301
C304
C308
C310
C311
C312
C313
C317
VCEA0A1CW476M+X
VCEA0A0JW108M+ X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCEA0A1HW106M+X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCKYCY1HB102KY X
VCEA0A1CW477M+X
VCEA0A1CW106M+X
VCKYCY1HB822KY X
VCEA0A1HW105M+X
VCEA0A1HW105M+X
VCEA0A1HW224M+X
VCKYCY1HB822KY X
VCE9GA1CW106M+X
C318
C321
C322
C391
C392
C393
C434
VCEA0A1CW107M+X
VCEA0A1HW224M+X
VCEA0A1HW105M+X
VCKYPA1HB102K+ X
VCQYTA1HM103J+ X
VCEA0A1EW108M+X
VCE9GA1CW106M+X
C435
VCE9GA1CW106M+X
C436
C437
VCKYCY1EF104ZY X
VCE9GA1HW106M+X
C438
C439
C452
VCEA0A1CW106M+X
VCKYCY1HF103ZY X
VCE9GA1CW106M+X
C505
C508
C511
C512
C513
C514
C515
C518
C601
C602
C603
C604
C606
å C607
VCEA0A1HW107M+X
VCFYAA2AA224J+ X
VCEA0A1VW477M+X
VCKYPA2HB102K+ X
RC-EZA332WJZZ+ X
VCFYSA1JB273J+ X
VCEACA1HC335J+ X
VCKYCY1HF103ZY X
VCQYTA1HM563J+ X
VCEA0A1HW475M+X
VCEA0A1HW105M+X
VCEA0A2EW336M+X
VCKYPA2HB102K+ X
VCFPFD3ZA912H X
C608
C610
C611
VCQYTA2AA103K+ X
VCEA0A1EW227M+X
VCFPVC2DB334J X
C642
C643
C650
å C701
C702
C703
C704
VCEA0A1EW476M+X
VCEA0A1AW477M+X
VCKYPA2HB101K+ X
RC-FZ029SCEZZ X
RC-KZ0029CEZZ+ X
RC-KZ0029CEZZ+ X
RC-KZ0029CEZZ X
47
16V Electrolytic
1000 6.3V Electrolytic
0.01 50V Ceramic
0.01 50V Ceramic
10
50V Electrolytic
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
1000p 50V Ceramic
470 16V Electrolytic
10
16V Electrolytic
8200p 50V Ceramic
1
50V Electrolytic
1
50V Electrolytic
0.22 50V Electrolytic
8200p 50V Ceramic
10
16V Electrolytic,
(N.P)
100 16V Electrolytic
0.22 50V Electrolytic
1
50V Electrolytic
1000p 50V Ceramic
0.01 50V Mylar
1000 25V Electrolytic
10
16V Electrolytic,
(N.P)
10
16V Electrolytic,
(N.P)
0.1
25V Ceramic
10
50V Electrolytic,
(N.P)
10
16V Electrolytic
0.01 50V Ceramic
10
16V Electrolytic,
(N.P)
100 50V Electrolytic
0.22 100V
470 35V Electrolytic
1000p 500V Ceramic
Capacitor
0.027 63V
3.3
50V Electrolytic
0.01 50V Ceramic
0.056 50V Mylar
4.7
50V Electrolytic
1
50V Electrolytic
33
250V Electrolytic
1000p 500V Ceramic
9100p 1800V
MetalIzed Polypro Film
0.01 100V Mylar
220 25V Electrolytic
0.33 200V
MetalIzed Polypro Film
47
25V Electrolytic
470 10V Electrolytic
100p 500V Ceramic
Capacitor
0.01 250V Ceramic
0.01 250V Ceramic
0.01 250V Ceramic
AB
AB
AA
AA
AB
AA
AA
AA
AA
AA
AB
AA
AA
AB
AB
AB
AA
AB
AB
AB
AB
AA
AB
AB
AB
AB
AA
AB
AA
AA
AB
AB
AC
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
41
Ref. No.
Part No.
★
å C705
C706
C708
C709
C710
C711
C718
C743
C750
C751
C752
C753
C754
C755
C756
C784
C801
C802
C803
C804
C805
C806
C807
C808
C809
C810
C811
C814
C815
C816
C817
C818
C819
C820
C821
C822
RC-EZA097WJZZ X
VCEA0A1VW226M+X
VCKYPA1HB471K+ X
VCEA9M1HW105M+X
VCFYFA1HA104J+ X
VCKYPA1HB681K+ X
VCKYPA2HB472K+ X
VCKYPH3DB561K X
VCKYPA2HB102K+ X
RC-KZ0106GEZZ X
VCKYPH3DB561K X
RC-EZ0724CEZZ X
RC-EZ0638CEZZ X
VCQYTA1HM103J+ X
VCEA0A1EW228M+X
RC-KZ0341CEZZ X
VCFYFA1HA105J+ X
VCKYCY1HF103ZY X
VCEA9M1CW476M+X
VCKYCY1HF103ZY X
VCEA0A1HW105M+X
VCKYCY1HF103ZY X
VCEA0A1CW337M+X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCEA9M1CW106M+X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCKYCY1EF104ZY X
VCEA9M1CW107M+X
VCEA9M1HW475M+X
VCCCCY1HH121JY X
VCEA9M1HW474M+X
VCKYCY1HF153ZY X
VCE9GA1HW105M+X
C823
C824
C825
VCKYCY1EF104ZY X
VCEA0A1CW337M+X
VCE9GA1HW105M+X
C826
C827
C828
C829
C831
C833
C834
C835
C836
C837
C839
C840
C841
C842
C843
C845
C846
C847
C848
C1001
C1003
C1004
C1006
C1007
C1008
C1009
C1011
C1012
C1013
C1014
VCKYCY1HF103ZY X
VCEA0A1CW476M+X
VCKYCY1HF103ZY X
VCEA9M1CW476M+X
VCKYCY1EF104ZY X
VCKYCY1EF104ZY X
VCEA0A1CW107M+X
VCEA0A1CW106M+X
VCKYCY1HF103ZY X
VCEA9M1HW105M+X
VCCCCY1HH680JY X
VCFYFA1HA105J+ X
VCCCCY1HH101JY X
VCEA9M1HW474M+X
VCEA0A1HW105M+X
VCKYCY1CF224ZY X
VCKYCY1HF103ZY X
VCCCCY1HH220JY X
VCEA9M1HW105M+X
VCEA0A1AW107M+X
VCEA0A1CW106M+X
VCKYCY1CF474ZY X
VCEA0A1HW225M+X
VCEA0A1CW107M+X
VCKYCY1HF103ZY X
VCKYCY1HF103ZY X
VCKYCY1HB221KY X
VCEA0A1HW105M+X
VCKYCY1HB102KY X
VCE9GA1HW475M+X
C1015
C1016
C1020
C1081
VCCCCY1HH101JY X
VCKYCY1EF104ZY X
VCEA0A0JW477M+ X
VCQYTA1HM104J+ X
Description
220
22
470p
1
0.1
680p
4700p
560p
1000p
3300p
560p
100
33
0.01
2200
1000p
1
0.01
47
0.01
1
0.01
330
0.01
0.01
0.01
10
0.01
0.01
0.1
100
4.7
120p
0.47
0.015
1
(N.P)
0.1
330
1
(N.P)
0.01
47
0.01
47
0.1
0.1
100
10
0.01
1
68p
1
100p
0.47
1
0.22
0.01
22p
1
100
10
0.47
2.2
100
0.01
0.01
220p
1
1000p
4.7
(N.P)
100p
0.1
470
0.1
Code
400V
35V Electrolytic
50V Ceramic
50V Electrolytic
50V
50V Ceramic
500V Ceramic
2000V Ceramic
500V Ceramic
250V Ceramic
2KV Ceramic
160V Electrolytic
160V Electrolytic
50V Mylar
25V Electrolytic
25V
50V Mylar
50V Ceramic
16V Electrolytic
50V Ceramic
50V Electrolytic
50V Ceramic
16V Electrolytic
50V Ceramic
50V Ceramic
50V Ceramic
16V Electrolytic
50V Ceramic
50V Ceramic
25V Ceramic
16V Electrolytic
50V Electrolytic
50V Ceramic
50V Electrolytic
50V Ceramic
50V Electrolytic,
AG
AB
AA
AA
AB
AA
AB
AB
AB
AB
AB
AC
AC
AB
25V Ceramic
16V Electrolytic
50V Electrolytic,
AA
AB
AB
50V
16V
50V
16V
25V
25V
16V
16V
50V
50V
50V
50V
50V
50V
50V
16V
50V
50V
50V
10V
16V
16V
50V
16V
50V
50V
50V
50V
50V
50V
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Electrolytic,
AA
AB
AA
AA
AA
AA
AB
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AB
AA
AB
50V
25V
6.3V
50V
Ceramic
Ceramic
Electrolytic
Mylar
AA
AA
AB
AB
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Ceramic
AB
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AB
21FL94
Ref. No.
Part No.
★
C1849
C1855
C1856
C1861
C1862
C1863
C1864
C1868
VCFYFA1HA223J+ X
VCKYCY1HB561KY X
VCKYCY1HB102KY X
VCCCCY1HH221JY X
VCKYCY1HB102KY X
VCCCCY1HH221JY X
VCKYCY1HB102KY X
VCEA9M1CW336M+X
RJ1
RJ3
RJ5
RJ9
RJ10
RJ12
RJ13
RJ14
RJ17
RJ18
RJ19
RJ20
RJ22
RJ25
RJ26
RJ29
RJ30
RJ101
R201
R202
R205
R206
R207
R208
R209
R216
R220
R301
R302
R303
R304
R305
R307
R308
R311
R314
R315
R362
R363
R365
R366
R381
R382
R383
R384
R431
R432
R433
R434
R435
R436
R437
R438
R461
R462
R502
R503
R504
R506
R507
R513
R514
R520
R524
R525
R526
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF000JY X
VRS-CY1JF101JY X
VRS-CY1JF101JY X
VRS-CY1JF680JY X
VRS-CY1JF122JY X
VRS-CY1JF221JY X
VRS-CY1JF331JY X
VRS-CY1JF392JY X
VRS-RG3LB333J+ X
VRS-CY1JF221JY X
VRS-CY1JF102JY X
VRN-RL3DBR10J+ X
VRS-CY1JF473JY X
VRD-RA2BE683JY X
VRS-CY1JF274JY X
VRS-CY1JF222JY X
VRS-CY1JF822JY X
VRD-RA2BE103JY X
VRS-CY1JF822JY X
VRS-CY1JF222JY X
VRS-CY1JF332JY X
VRS-CY1JF564JY X
VRS-CY1JF564JY X
VRS-CY1JF332JY X
VRS-CY1JF564JY X
VRS-CY1JF332JY X
VRS-CY1JF564JY X
VRS-CY1JF332JY X
VRS-CY1JF101JY X
VRS-CY1JF750JY X
VRS-CY1JF750JY X
VRS-CY1JF750JY X
VRS-CY1JF750JY X
VRD-RA2BE101JY X
VRS-CY1JF101JY X
VRS-CY1JF000JY X
VRS-CY1JF750JY X
VRS-CY1JF101JY X
VRS-RG3AB102J+ X
VRN-RL3DB1R2J+ X
VRS-CY1JF222JY X
VRS-RG3AB331J+ X
VRD-RM2HD1R0JY X
VRD-RM2HD333JY X
VRD-RM2HD682JY X
VRS-CY1JF123JY X
VRD-RA2BE103JY X
VRD-RA2BE122JY X
VRD-RA2BE101JY X
Description
0.022
560p
1000p
220p
1000p
220p
1000p
33
50V
50V
50V
50V
50V
50V
50V
16V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
AA
AA
AA
AA
AA
AA
AA
å
RESISTORS
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
100
100
68
1.2k
220
330
3.9k
33k
220
1k
0.1
47k
68k
270k
2.2k
8.2k
10k
8.2k
2.2k
3.3k
560k
560k
3.3k
560k
3.3k
560k
3.3k
100
75
75
75
75
100
100
0
75
100
1k
1.2
2.2k
330
1
33k
6.8k
12k
10k
1.2k
100
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
3W
1/16W
1/16W
2W
1/16W
1/8W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1W
2W
1/16W
1W
1/2W
1/2W
1/2W
1/16W
1/8W
1/8W
1/8W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Ref. No.
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
å
å
å
å
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
42
R528
R601
R602
R603
R604
R605
R607
R608
R609
R611
R612
R613
R614
R615
R616
R617
R618
R621
R622
R631
R637
R638
R639
R642
R661
R662
R701
R702
R704
R705
R706
R710
R711
R712
R713
R725
R726
R753
R754
R756
R801
R802
R803
R804
R805
R806
R807
R808
R812
R814
R815
R816
R817
R818
R823
R824
R826
R827
R828
R829
R830
R831
R832
R833
R835
R836
R838
R839
R840
R841
R842
R843
R847
R1002
R1003
R1006
Part No.
★
VRS-CY1JF683JY
VRD-RM2HD820JY
VRD-RA2BE393JY
VRD-RA2BE273JY
VRD-RA2BE473JY
VRD-RM2HD104JY
VRD-RM2HD121JY
VRD-RM2HD102JY
VRD-RM2HD270JY
VRN-RL3AB1R0J+
VRD-RM2HD270JY
VRS-CY1JF000JY
VRD-RA2BE154JY
VRD-RA2BE102JY
VRD-RA2BE102JY
VRS-CY1JF123JY
VRS-CY1JF103JY
VRN-RL2HC4R7J+
VRS-VV3DB682J
VRS-KT3LB391J
VRD-RA2BE331JY
VRD-RA2BE181JY
VRD-RM2HD271JY
VRN-RL3DB2R2J+
VRD-RA2BE102JY
VRS-CY1JF103JY
VRW-KQ3NC1R5K
VRD-RM2HD154JY
VRD-RA2BE101JY
VRN-RL3DBR47J+
VRN-RL3DBR39J+
VRD-RM2HD220JY
VRD-RA2EE122JY
VRD-RA2BE102JY
VRD-RA2BE102JY
VRD-RM2HD821JY
VRN-RL2HCR47J+
VRD-RM2HD124JY
VRN-RL3AB8R2J+
VRS-RG3DB121J+
VRS-CY1JF561JY
VRS-CY1JF682JY
VRS-CY1JF103JY
VRS-CY1JF222JY
VRS-CY1JF222JY
VRS-CY1JF222JY
VRS-CY1JF222JY
VRD-RA2BE273JY
VRS-CY1JF101JY
VRS-CY1JF473JY
VRS-CY1JF473JY
VRS-CY1JF223JY
VRS-CY1JF473JY
VRD-RS2BE102JY
VRD-RA2BE101JY
VRD-RA2BE101JY
VRD-RA2BE101JY
VRS-CY1JF102JY
VRS-CY1JF471JY
VRD-RA2BE472JY
VRS-CY1JF393JY
VRS-CY1JF271JY
VRS-CY1JF822JY
VRS-CY1JF221JY
VRS-CY1JF332JY
VRD-RA2BE470JY
VRD-RA2BE105JY
VRS-CY1JF101JY
VRS-CY1JF124JY
VRD-RA2BE821JY
VRS-CY1JF471JY
VRS-CY1JF103JY
VRS-CY1JF475JY
VRS-CY1JF183JY
VRS-CY1JF822JY
VRS-CY1JF822JY
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Description
68k
82
39k
27k
47k
100k
120
1k
27
1
27
0
150k
1k
1k
12k
10k
4.7
6.8k
390
330
180
270
2.2
1k
10k
1.5
150k
100
0.47
0.39
22
1.2k
1k
1k
820
0.47
120k
8.2
120
560
6.8k
10k
2.2k
2.2k
2.2k
2.2k
27k
100
47k
47k
22k
47k
1K
100
100
100
1k
470
4.7k
39k
270
8.2k
220
3.3k
47
1M
100
120k
820
470
10k
4.7M
18k
8.2k
8.2k
1/16W
1/2W
1/8W
1/8W
1/8W
1/2W
1/2W
1/2W
1/2W
1W
1/2W
1/16W
1/8W
1/8W
1/8W
1/16W
1/16W
1/2W
2W
3W
1/8W
1/8W
1/2W
2W
1/8W
1/16W
7W
1/2W
1/8W
2W
2W
1/2W
1/4W
1/8W
1/8W
1/2W
1/2W
1/2W
1W
2W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Metal Film
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Film
Carbon
Metal Oxide
Cement
Carbon
Carbon
Metal Film
Metal Film
Carbon
Carbon
Carbon
Carbon
Carbon
Metal Film
Carbon
Metal Film
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Code
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
21FL94
Part No.
★
R1007
R1008
R1009
R1011
R1012
R1023
R1024
R1027
R1031
R1032
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1042
R1043
R1044
R1045
R1046
R1047
R1048
R1049
R1051
R1053
R1054
R1055
R1056
R1059
R1061
R1062
R1063
R1064
R1065
R1066
R1072
R1073
R1074
R1076
R1081
R1087
R1096
R1097
R1098
R1801
R1802
R1849
R1850
R1851
R1852
R1853
R1854
R1855
R1861
R1862
R1894
R1895
R1896
VRS-CY1JF103JY
VRS-CY1JF183JY
VRS-CY1JF103JY
VRD-RA2BE101JY
VRD-RA2BE101JY
VRD-RA2BE271JY
VRS-CY1JF101JY
VRS-CY1JF104JY
VRD-RA2BE101JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRD-RA2BE101JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRS-CY1JF562JY
VRS-CY1JF102JY
VRD-RA2BE273JY
VRS-CY1JF103JY
VRD-RA2BE101JY
VRS-CY1JF104JY
VRS-CY1JF101JY
VRD-RA2BE101JY
VRS-CY1JF101JY
VRS-CY1JF183JY
VRS-CY1JF101JY
VRS-CY1JF183JY
VRD-RA2BE473JY
VRD-RA2BE101JY
VRD-RA2BE101JY
VRS-CY1JF332JY
VRS-CY1JF332JY
VRS-CY1JF103JY
VRS-CY1JF102JY
VRS-CY1JF105JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRS-CY1JF561JY
VRS-CY1JF221JY
VRD-RA2BE101JY
VRS-CY1JF103JY
VRS-CY1JF102JY
VRS-CY1JF103JY
VRS-CY1JF391JY
VRS-CY1JF103JY
VRS-CY1JF472JY
VRS-CY1JF104JY
VRD-RA2BE222JY
VRS-CY1JF124JY
VRS-CY1JF222JY
VRS-CY1JF472JY
VRS-CY1JF221JY
VRS-CY1JF221JY
VRS-CY1JF221JY
VRS-CY1JF103JY
VRD-RA2BE102JY
VRS-CY1JF121JY
VRS-CY1JF121JY
VRD-RA2BE103JY
VRS-CY1JF473JY
VRS-CY1JF473JY
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
FB601
RBLN-0091GEZZY X Balun, BLN-0091GE
S1001
S1002
S1003
S1004
S1005
S1006
QSW-K0202PEZZ+
QSW-K0202PEZZ+
QSW-K0202PEZZ+
QSW-K0202PEZZ+
QSW-K0202PEZZ+
QSW-K0114CEZZ
Ref. No.
Description
10k
18k
10k
100
100
270
100
100k
100
10k
10k
100
10k
10k
5.6k
1k
27k
10k
100
100k
100
100
100
18k
100
18k
47k
100
100
3.3k
3.3k
10k
1k
1M
10k
10k
10k
560
220
100
10k
1k
10k
390
10k
4.7k
100k
2.2k
120k
2.2k
4.7k
220
220
220
10k
1k
120
120
10k
47k
47k
1/16W
1/16W
1/16W
1/8W
1/8W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Code
Ref. No.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
å FH702
J401
J402
J403
J404
J405
J406
P302
P601
P602
P603
P701
P702
P1001
P1002
RDA301
RDA501
RDA601
RDA602
RDA701
RMC1001
å RY701
Fuse Holder
Jack, 5Pin
Jack, 3Pin
Jack, 3Pin
Jack, 3Pin
Jack, 9Pin
Jack, 4Pin
Plug, 4Pin (S)
Plug, 6Pin (K)
Plug, 4Pin
Plug, 3Pin (TP651-3)
Plug, 2Pin (M)
Plug, 2Pin
Plug, 5Pin
Plug, 5Pin (BC)
Heat Sink, IC301
Heat Sink, IC501
Heat Sink, IC601
Heat Sink
Heat Sink, IC701
Remote Receiver
Relay
Holder
Code
AB
AD
AB
AB
AB
AE
AC
AB
AB
AB
AB
AB
AB
AB
AA
AB
AB
AB
AC
AC
AC
AB
TRANSISTORS
Q853
Q854
Q855
Q894
VS2SC3789//2E
VS2SC3789//2E
VS2SC3789//2E
VS2SA1015Y/1E+
X
X
X
X
2SC3789
2SC3789
2SC3789
2SA1015Y
AB
AB
AB
AB
D859
D898
VHD1SS119//-1Y
VHD1SS119//-1Y
L851
VP-MK820K0000+ X Peaking, 82µH
C851
C852
C853
C880
C893
VCKYPA1HB221K+ X
VCKYPA1HB221K+ X
VCKYPA1HB221K+ X
RC-KZ0153CEZZ X
VCEA0A1CW336M+X
DIODES
X 1SS119
X 1SS119
AA
AA
COIL
AB
CAPACITORS
220p
220p
220p
1000p
33
50V
50V
50V
3KV
16V
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
AA
AA
AA
AB
AA
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
R849
R850
R851
R852
R854
R855
å R859
å R861
å R863
R864
R876
R877
R878
R880
R881
R882
R889
R891
R892
R894
R895
SWITCHES
Switch, CH-Up
Switch, CH-Down
Switch, VOL-Up
Switch, VOL-Down
Switch, MENU
Switch, POWER
QFSHD1014CEZZ+ X
QJAKGA015WJZZ X
QJAKE0108CEZZ X
QJAKE0183CEZZ X
QJAKE0184CEZZ X
QJAKG0093CEZZ X
QJAKFA008WJZZ X
QPLGN0461CEZZA X
QPLGN0660CEZZ X
QPLGN0461CEZZA X
QPLGN0361CEZZA X
QPLGN0260CEZZ X
QPLGN0269GEZZ X
QPLGN0561CEZZA X
QPLGN0561CEZZ X
PRDARA121WJFW X
PRDARA120WJFW X
PRDARA131WJFW X
PRDAR0337PEFW X
PRDARA119WJFW X
RRMCUA009WJZZ X
RRLYJA006WJZZ X
LHLDP1066PE00 X
Description
DUNTKA599WED5
PWB-B CRT UNIT
BALUN
X
X
X
X
X
X
★
Part No.
AB
AB
AB
AB
AB
AC
VRD-RA2BE221JY
VRD-RA2BE470JY
VRD-RA2BE470JY
VRD-RA2BE470JY
VRD-RA2BE271JY
VRD-RA2BE271JY
VRS-VV3DB123J
VRS-VV3DB123J
VRS-VV3DB123J
VRD-RA2BE470JY
VRD-RA2BE121JY
VRD-RA2BE121JY
VRD-RA2BE121JY
VRD-RM2HD332JY
VRD-RM2HD332JY
VRD-RM2HD332JY
VRD-RA2BE821JY
VRD-RA2BE561JY
VRD-RA2BE391JY
VRD-RA2BE152JY
VRD-RA2BE561JY
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
220
47
47
47
270
270
12k
12k
12k
47
120
120
120
3.3k
3.3k
3.3k
820
560
390
1.5k
560
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
2W
2W
2W
1/8W
1/8W
1/8W
1/8W
1/2W
1/2W
1/2W
1/8W
1/8W
1/8W
1/8W
1/8W
MISCELLANEOUS PARTS
MISCELLANEOUS PARTS
å F701
å FH701
QFS-C3229CEZZ X Fuse, T3. 15AL
QFSHD1013CEZZ+ X Fuse Holder
P860
P880
SC851
AB
AB
43
QPLGN0461CEZZ X Plug, 4Pin
QPLGN0561CEZZ X Plug, 5Pin
QSOCV0933CEZZ X Socket, 12Pin
AA
AA
AC
21FL94
Ref. No.
Part No.
★
Description
Ref. No.
Code
DUNTKC574WEA0
PWB-C MTS UNIT
PWB-C MTS UNIT
INTEGRATED CIRCUIT
IC3001 VHiCXA2194Q-1Y
X CXA2194Q
AP
TRANSISTORS
Q3001
Q3002
Q3004
Q3005
Q3006
Q3007
VS2SD601AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
VS2SD601AR/-1Y
X
X
X
X
X
X
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
C3001
C3017
C3018
C3019
C3020
C3021
C3022
C3023
C3024
C3025
C3026
C3030
C3031
C3034
C3037
C3038
C3039
C3042
C3043
C3044
C3045
C3046
C3047
C3048
VCE9GA1HW475M+X 4.7
(N.P)
VCKYCY1HB562KY X 5600p
VCQYTA1HM123K+ X 0.012
VCEA0A1HW105M+X 1
VCEA0A1HW475M+X 4.7
VCEA0A1CW106M+X 10
VCEA0A1HW475M+X 4.7
VCKYCY1HF103ZY X 0.01
VCEA0A1CW227M+X 220
VCE9GA1HW475M+X 4.7
(N.P)
VCEA0A1HW475M+X 4.7
VCE9GA1HW475M+X 4.7
(N.P)
VCKYCY1HB272KY X 2700p
VCQYTA1HM473K+ X 0.047
VCEACA1HC335K+ X 3.3
VCE9GA1HW475M+X 4.7
(N.P)
VCEACA1CC106K+ X 10
VCEA0A1HW105M+X 1
VCEA0A1CW106M+X 10
VCEA0A1CW106M+X 10
VCEA0A1CW106M+X 10
VCEA0A1CW106M+X 10
VCKYCY1HF103ZY X 0.01
VCKYCY1HF103ZY X 0.01
VCKYCY1HF473ZY X 0.047
VCKYCY1HF473ZY X 0.047
VCQYTA1HM682K+ X 6800p
VCKYCY1HF682ZY X 6800p
VCEA0A1HW224M+X 0.22
VCEA0A1HW335M+X 3.3
VCEA0A1HW335M+X 3.3
VCEA0A1HW224M+X 0.22
VCKYCY1HB681KY X 680p
VCKYCY1HB681KY X 680p
VCEA0A1EW476M+X 47
VCEA0A1HW335M+X 3.3
VCEA0A1HW335M+X 3.3
VCEA0A1HW335M+X 3.3
VCEA0A1HW335M+X 3.3
R3001
R3002
R3003
R3004
R3005
R3006
R3007
R3008
R3009
R3010
R3011
R3012
R3013
R3014
VRS-CY1JF221JY
VRS-CY1JF221JY
VRS-CY1JF105JY
VRS-CY1JF104JY
VRS-CY1JF623JY
VRS-CY1JF101JY
VRS-CY1JF332JY
VRS-CY1JF302JY
VRS-CY1JF101JY
VRS-CY1JF392JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF102JY
AB
AB
AB
AB
AB
AB
CAPACITORS
C3002
C3003
C3004
C3005
C3006
C3007
C3008
C3009
C3010
C3011
C3012
C3013
C3014
C3015
C3016
50V Electrolytic,
AB
50V
50V
50V
50V
16V
50V
50V
16V
50V
Ceramic
Mylar
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Electrolytic,
AA
AB
AB
AB
AA
AB
AA
AB
AB
50V Electrolytic
50V Electrolytic,
AB
AB
50V
50V
50V
50V
Ceramic
Mylar
Electrolytic
Electrolytic,
AA
AB
AB
AB
16V
50V
16V
16V
16V
16V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
25V
50V
50V
50V
50V
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Mylar
Ceramic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
AB
AB
AA
AA
AA
AA
AA
AA
AB
AB
AA
AB
AA
AA
AB
AA
AA
AB
AA
AA
AA
AA
220
220
1M
100k
62k
100
3.3k
3k
100
3.9k
1k
1k
1k
1k
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
R3016
R3018
R3019
R3021
R3025
R3026
R3027
R3028
R3029
R3030
R3031
R3032
R3033
R3034
R3035
R3036
R3082
R3083
R3084
R3085
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF272JY
VRS-CY1JF331JY
VRS-CY1JF392JY
VRS-CY1JF683JY
VRS-CY1JF392JY
VRS-CY1JF683JY
VRS-CY1JF182JY
VRS-CY1JF223JY
VRS-CY1JF102JY
VRS-CY1JF182JY
VRS-CY1JF223JY
VRS-CY1JF102JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRS-CY1JF103JY
P3007
P3008
P3009
QPLGZ0610CEZZ
QPLGZ0610CEZZ
QPLGZ0810CEZZ
★
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Description
1k
1k
1k
1k
2.7k
330
3.9k
68k
3.9k
68k
1.8k
22k
1k
1.8k
22k
1k
10k
10k
10k
10k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
RESISTORS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Part No.
44
X Plug, 6Pin
X Plug, 6Pin
X Plug, 8Pin
AB
AB
AB
21FL94
Ref. No.
Part No.
★
Description
Code
AC Cord
Speaker
AC Cord Holder
Holder
Holder
Caution Card
Connecting Cord
Connecting Cord
Connecting Cord
Plug
AC
AK
AB
AB
AB
AB
AB
AC
AC
AC
SUPPLIED ACCESSORIES
ACCESSORIES
RRMCGA108WJSA X Infrared R-C
TiNS-B246WJZZ
X Operation Manual
AT
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKCB318WJZZ
SPAKPA055WJZZ
SPAKXA145WJZZ
SSAKA0101GJZZ
TLABM0005GJZZ
TLABZA713WJZZ
-
Packing Case
Wrapping Paper
Buffer Material
Polyethylene Bag
Model Label
Label
—
—
—
—
—
—
CABINET PARTS
1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
2
CCABAA596WEH0
Not Avairable
HBDGB3155CESA
HDECQA403WJSA
JBTN-A070WJKD
MSPRC0005PEFW
GDORFA015WJKD
MSPRPA012WJFW
HiNDPA194WJSA
GBFL-A007WJZZ
GCABBA088WJKA
X
X
X
X
X
X
X
X
X
X
Front Cabinet Ass'y
Front Cabinet
SHARP Badge
LED, R/C Cover
Power Button
Power Button Spring
Door
Door Spring
Indication Plate
Speaker Baffer
Rear Cabinet
Part No.
★
Description
CABINET PARTS LOCATION
MISCELLANEOUS PARTS
å ACC701 QACCZA020WJPZ X
SP301 VSP1205PB09WA X
LHLDK0014PEZZ X
LHLDZA096WJZZ X
LHLDZA107WJZZ X
TCAUH3045GJZZ X
QCNW-A871WJZZ X
QCNW-A872WJZZ X
QCNW-A873WJZZ X
QPLGA0017CEZZ X
Ref. No.
—
AD
AA
AB
AC
AC
AX
45
Code
21FL94
Ref. No.
Part No.
★
Description
PACKING OF THE SET
Ref. No.
Code
46
Part No.
★
Description
Code
21FL94
Ref. No.
Part No.
★
Description
Code
Ref. No.
-MEMO-
47
Part No.
★
Description
Code
21FL94
Ref. No.
Part No.
★
Description
Ref. No.
Code
Part No.
★
Description
Code
COPYRIGHT © 2004 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
TQ1756-S
Jun 2004 Printed in Japan
In Japan gedruckt
Design and Production Information
Design
: SEM
Production : SEMEX
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
MY. DS
48